Qosmio G does not recognize the mouse using two left USB ports

Similar Questions

• installation screen does not recognize the mouse/keyboard

  Hello
  Passage of the Pro x 86 to x 64. I do not have a disk original as a burnt image, which seems to me to be recent. I got the link for him to store chat session windows today. Keyboard and wireless mouse work fine in the bios. When it is at the first Setup screen (where it asks for the language, country, etc) there is no cursor or keyboard response, so I can't start the installation. I have ONLY usb 3.0 on this build. X 86 installed fine. Any recommendations? I tried to unplug all other usb devices and tried UN / reconnect the bluetooth receiver. Nothing seems to help.

  Another couple of things you can try is:

  (1) check your BIOS for USB, mouse, wirelesss options settings.

  (2) move the transmitter to a different USB port USB wireless until you find one that works.

  (I suggest this because 2 of my ports were dead until I could insstall Windows, then the pilot, but worked at least 2 other ports).

  J W Stuart: http://www.pagestart.com

• L50-B-11J satellite does not recognize the HARD drive connected by USB 3.0

  Hello

  I recently bought a new laptop and install a new legal copy of windows pro 8.1.

  The problem that arises is actually a USB 3.0 port.
  Also, I have a drive external hard support standard USB 2.0 and 3.0.

  When I plug-in the hard drive into a USB 2.0 or any USB 3.0 port (two port supports USB 3.0 is disabled in the BIOS) fine, hard drive is recognized and I can access.

  But, when I plug-in the hard disk into a USB 3.0 port (two port supports USB 3.0 is active in the BIOS) Windows does not recognize it and I can't access it.

  The hard disk led flashes, so it has the power, but does not appear in the devices or Device Manager.
  My opinion is that the problem may be with the drivers for USB, but Toshiba is supported for driver for USB 3.0 for Windows 8.1.

  Then can someone suggest me what to do?

  Laptop: Satellite L50-B-11J
  USB ports: 1xUSB 2.0 port, 2xUSB 3.0 port
  Operating system: Windows Pro 8.1
  USB 3.0 driver: Intel (r) USB 3.0 eXtensible Host Control - 0100 (Microsoft)
  External hard drive: support USB 2.0 and USB 3.0 standard

  Intel USB 3.0 driver is part of the 8.1 Windows System... This is not supplied by Toshiba.

  Windows 7 contains no such USB 3.0 driver and so you can download driver Intel USB 3.0 page of the Toshiba driver as well as the Intel download site.

  By the way: try to disable the functionality of sleep & Charge and check how the HARD drive would work.

• Computer suddenly does not recognize the mouse.

  Mouse frozen earlier this evening. Tried to reboot the computer, but the mouse icon is stuck on the same position on the screen. I tried two other mice, USB connection or wireless all plugged into several USB ports. USB power lasers on mice, but there is no movement for the icon. Any help would be appreciated.

  Try a PS/2 mouse.

  Also, make sure that the other devices (except the mouse) on this port works fine or not?

  S.Chatterjee

• Computer does not recognize the phone when connected via USB

  original title: usb recogonozation

  I want to connect my phone to my pc via the usb port but its upcoming Dungeon with an error stating that my device has mafunctioned or he stopped window. can someone pls tell me what to do? Thank you very much

  As a first step, check for compatibility with Windows 7 at http://www.microsoft.com/windows/compatibility/windows-7/en-gb/Default.aspx and on the site of the manufacturer of phone support.

• Windows Vista does not recognize my camera when plugged into USB port

  I recently had a problem with updates do not install it on my laptop Gateway 6840 running Vista. Community Microsoft guided me through a process that solved the problem and it worked fine. However, later, I tried to plug my Fujifilm AX560 into a USB port and the computer is no longer recognized. Ports recognize my memory sticks though very slowly. I tried a lot of previous solutions on Microsoft Community, but nothing has worked. Appreciate any help.  Thank you.

  Problem solved! I used sugestion of Shekhar S to use Microsoft Fix It only the second I had my camera is plugged in and turned on. Thanks Shekhar S and thank you Microsoft Community.

• Qosmio G30 does not recognize the SD card

  Hello

  Can you help me? My SD card is not recognized when I push it.
  Is there a driver I need to download to fix this?

  Post edited by: ADMIN

  Hi Steve

  First of all, you should check if your SD card is compatible with the SD G30 s card slot.

  Not all SD card sizes are compatible and supported by the SD card reader and this could be the reason why the SD card can not be used Don t know what card you want to use, but the user manual should provide some details on the SD card compatible card formats.

  On the other hand, it would be possible that your SD card driver has stopped working. Why? Who knows, but in this case, you need to go to Device Manager and should remove the SD card reader in the list.
  Then restart the computer laptop windows operating system would recognize new devices immediately after new reboot and you would be able to trace the river of SD card

  After this short procedure try to insert the SD card and check if the card will be recognized.

• Laptop does not recognize the usb mouse or the internal speakers.

  The laptop does not recognize the USB mouse. I have re installed the drivers from the site of the constructor (HP), but it still does not work.

  In addition, the internal Laptop speakers no longer work. There is no sound coming out of the laptop and it does not recognize the external headphones plugged into the headphone jack.

  I ran several troubleshooting utilities (audio playback, FixIt) and they are no help.

  Hello

  Thank you for keeping us posted.

  Sorry for the late reply.

  I imagine the inconvenience that you are experiencing. However, I appreciate your efforts to resolve the issue.

  I would suggest trying the following methods and check if it helps.

  Method 1:

  How to use the tool File Checker system to repair missing or corrupted system files,

  Please follow the steps in the link provided below.

  https://support.Microsoft.com/kb/929833?WA=wsignin1.0

  Note: System File Checker is a Windows utility that allows users to find corruptions in Windows system files and restore the damaged files. This article describes how to run the system (SFC.exe) to File Checker tool analyzes your system files and to repair the system missing or corrupt files in Windows or Windows 8 8.1. If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected.

  If the problem persists, follow method 2

  Method 2:

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft, security scanner please follow the steps in the link provided below.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.   

       

  If the problem persists, follow method 3

  Method 3:

  I suggest you try the steps from the following link and check if it works.

  No sound in Windows.

  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-8&V1H=win8tab4&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  For the problem with the USB mouse, there could be a possibility that there is a conflict of material with the mouse.

  I suggest you to try some other USB mouse with the laptop and check if it works.

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

• Qosmio F30 - 112 - Windows XP does not recognize the HARD drive

  Hello.

  I have a Qosmio F30-112.
  I tried to install the Windows XP Professional instead of the Media Center edition.
  However, during the execution of the installer, my laptop does not recognize the hard drive. Therefore, the installation cannot continue.

  I thought it might be a problem of corruption with my laptop and reinstalled Media Center Edition successfully.
  But when I try to install XP Professional it always gives me the same error.

  Suggestions for the configuration of the BIOS or solutions for why this is happening?

  Thanks in advance.

  Hello

  Just a question:
  You are looking for in this forum for other similar issues with regard to the installation of Win XP and lack HARD drive? I doubt

  The fact is that your notebook has a SATA controller and you need a SATA (Intel Matrix Storage Manager) driver.

  You should have a look here in this doc from Toshiba:
  [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

  and should also search this forum for other threads

  Good bye

• Cannot use my printer Officejet 4635 to the Mexico. Printer does not recognize the new cartridge.

  I moved my printer in Mexico City, HP Officejet 4635. It uses #61 cartridges. I was told that the 61 in the United States is the same as the #122 to the Mexico. However, the printer say it does not recognize the cartridge.

  Can someone give me some advice?

  Hi artist1234,

  Welcome to the HP Forums.

  Why the printer does not is because the unit is not regionalized for this part of the country.

  To get the printer to work, you will need to contact HP Total Care so that a representative from HP can regionalize the printer for you.

  If you call in North America, the number is 1-800-474-6836.  Seeing that you are in Mexico, please click here to access the information page you need.

  Thanks for your time.

  See you soon,.

• Pavilion HPE h8 1103nl does not recognize the keyboard & mouse

  After 10 days of installation, copy and all that kind of stuff that comes with a new PC, everything worked, and finally, I put everything in place, put the wires out of sight and all. Of course, I had to sign a few things, and somewhere in the process of electricity is out. Well, the PC was off anyway (at least I thought it was. I also changed the USB port to which the keyboard and mouse were attached. When I turned on the computer, I had a "keyboard" error, could not start (because electricity had come off the coast), but as the PC does not recognize the keyboard or the mouse, I was unable to give a or something.

  Keyboard and wireless mouse tried again, also under the old, but that didn't work.  Tried to reconnect, but in vain.

  Now what can I do?

  Hi HardBeatZ

  Thans for your answer!

  I found the solution, after trying and try... but could not find my ad more (duhhh), so thanks for the answer!

  Apparently I did ' t hold the button "connect" quite a long time to make a new connection... :-(

  Everything works fine now... Thanks again!

  Mijni

• Is there a bug in 9 Captivate, which does not recognize the click of the mouse for the title text?  Mac question

  I just installed 9 Captivate on my Mac, and it does not recognize the double click of the mouse to enter text in a title area.  Subtitle text works, but the text is not title.  I work in a reactive mode.

  Hi rayhoskins,

  We have not encountered such a problem. Can you please clear Captivate preferences and try again. .

  Captivate preferences can be erased by double-clicking the following file: Applications\Adobe Captivaate 9\utils\ClearPreferencesMac

  If you still face the issue please provide the Machine config?

  -Derrick

  Captivate the engineering team

• Qosmio F30 does not recognize USB devices

  My new Qosmio F30 does not recognize USB devices. Displays Device Manager USB ENHANCED CONTROLLER and ROOT HUB works fine, but the machine still wants to install each device but cannot. BIOS version seems to be V1.30. I tried the devices on other machines, and they work fine.
  Is there something that I missed?

  Hello

  Before your shot the beautiful F30 can you please say what OS you are using?
  Did you use the OS from the Toshiba restore CD?
  On this CD, all drivers must be preinstalled and you don t need to install no matter what chipsets or anything like that.

• Windows 7 64 bit does not recognize the USB external drive HARD Stor E art 3.5 "

  I buy the art external disk HARD Stor E 3.5 "and spend a few days in windows does not recognize the HARD drive. Try to connect the drive to other USB 2 ports and nothing happens. Use a USB to see if has been a problem with the USB ports, but all 3 are OK. Try it on the laptop Asus and windows 7 recognizes the HARD disk. I formatted the drive in NTFS FS. In managing records do not show the external HARD disk. What can I do to fix this?

  My laptop is a Qosmio F60

  This is a really silly situation. It can be recognized by other laptops but not your Qosmio.
  According to the description of your HARD drive when connected simply doesn t exist for your Qosmio laptop.

  Some other HDD is recognized correctly?
  What you can try is to reinstall the chipset driver, restart the laptop and test it again.

  Since when you have this problem? Some installed updates of the last days?

• DreamColor LP2480zx does not recognize the USB for calibration

  Hello

  I have a DreamColor LP2480zx, which does not recognize the USB connection to the computer during calibration.  I have my eye HP connected through this monitor, so I know the connection and the cable is good and mouse, keyboard.  My setup is like this:

  Reference Dell 690 running 64 bit + Windows XP

  DreamColor LP2480zx

  Apple Cinema Display 23 "

  I bought the DreamColor used, and in all other respects, it seems to work very well.  The original owner didn't have it calibrated within a certain time, but said that having had no problem with the previous calibration.  I installed the last APS (version 2.0) and updated to the latest firmware.  These updates produces no change in recognition USB problem.

  The interesting thing is, I was able to calibrate the Apple Cinema Display, using the same configuration of connection (mouse, keyboard, and HP eye connected to the computer via the LP2480zx) APS was able to see the USB connection and this very well calibrated monitor.

  I had trouble with this problem for a few days.  I've looked around quite a bit online and found a few others who have this same problem, but I did not yet find someone who can point out a solution.  If anyone has had this same problem, or has heard of results that correct it, please let me know, because it's very frustrating.

  Thanks for any help

  Clay

  An update to my previous post, I realized a work around for this problem.

  Apparently, this problem has to do with the Dreamcolor screen and/or software APS do not like working with 64 bit systems.  I'm not saying that it is always the case, but I saw the other posts on this problem on 64-bit systems, and I spoke with two other people personally who told me that they also had the same problem, try to calibrate its Dreamcolor monitor when it was attached to a 64-bit system.  HP does not seem to be concerned about this problem, because they do not even recognize its existence, but since I'm far from being the first to report this problem, he's obviously not a one-time problem.

  My solution was this: I had connect the monitor to a regular running XP 32 bit system.  After I did, I could re - calibrate the monitor without the problem of USB connection.  This isn't a very good solution because not everyone has access to several machines, running different operating systems.  But it's a work around, and it worked for me.

  Hope this helps other people who have this same problem with their Dreamcolor monitors hooked to their 64-bit systems.

  Clay

  PS- I posted this as resolved, only because I was able to calibrate my monitor.  It's not really solved the problem, but it gets the monitor working again.  Maybe HP will address this problem in the future, but I'm not holding my breath.