Question card crypto for VPN gateway router

Similar Questions

• Video support for voice gateway router can call?

  Hi all

  My gateway voice (Cisco 2921-V/K9) router to connect to the PSTN using SIP Trunk provider. CUCM 11 enter my ipphone and videoconferencing (SX20).

  If someone who using video-conferencing (SX20) to call my (SX20) videoconferencing via dial my number RTC, it only not Visual voice call of appeal.

  I have question: If the router voice gateway support video call?, if it can how to configure and there is an additional module?

  Thank you

  Cyriac

  Hi Cyriac,

  For a video call from point to point, you can see the "Configure the video telephony" section of the following link

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/CUCM/Admin/9_1_1/CCMS...

  If video conferencing Setup check the following "feature Deprecation announces for video Conferencing and transcoding using PVDM3 on ISR G2 product Bulletin"

  http://www.Cisco.com/c/en/us/products/collateral/unified-communications/...

  Manish

• Dynamic routing for VPN Failover L2L

  Hello

  Can someone offer me some advice on this please?

  I have attached a simple diagram of our EXTENSIVE referral network.

  Overview

  • The firewall is ASA 5510 running 8.4 (9)
  • Basic to the Headquarters network uses OSPF
  • On ASA static routes are redistributed into OSPF
  • On ASA for VPN static routes are redistributed into OSPF with 130 metric so redistributed BGP routes are preferred
  • Basic network has a static route to 10.0.0.0/8 to Corporate WAN, which is redistributed into OSPF
  • Branch Office WAN uses BGP - routes are redistributed into OSPF
  • The branch routers using VRRP for redundancy of the IP for the default gateway of local customers.
  • Branch router main past off VRRP IP to router backup when the WAN interface is down
  • BO backup router (. 253) contains only a default route to the internet
  • In normal operation, the traffic to and from BO uses Local Branch Office WAN
  • If local BO WAN link fails, traffic to and from the BO uses IPSec VPN via public Internet

  I try to configure dynamic routing on our network for when a branch switches to the IPsec VPN. What I want to happen (not sure if it is possible) is for the ASA announce the subnet to the remote end of the VPN in OSPF to Headquarters.

  I managed to get this working using IPP, but for some reason any VPN stay up all the time when we are not in a failover scenario. This causes the ASA added the table as a static route is the remote subnet in it and do not use the announced route of OSPF from the core network. This prevents the BO customers access to the Internet. If I remove the IPP on the VPN setting, ASA learns the route to the subnet via the WAN BO - resumes normal operation.

  I have configured the metric of the static routes that get redistributed into OSPF by ASA superior to 110. This is so that the routes redistributed by the WAN BO OSPF BGP, are preferred. The idea being that when the WAN link is again available, the routing changes automatically and the site fails to WAN BO.

  I guess what I need to know is; This design is feasible, and if so where I'm going wrong?

  Thank you

  Paul

  Hi Paul,.

  your ASA maintains the tunnel alive only because this path exists on ASA.  This is why you must use IP - SLA on ASA to push network taffic "10.10.10.0/24" based on the echo response, using the ALS-intellectual property

  Please look at the example below, in the example below shows that the traffic flows through the tunnel, only if the ASA cannot reach the 10.10.10.0/24 network via the internal network of HQ.

  This configuration illuminate ASA.

  Route inside 10.10.10.0 255.255.2550 10.0.0.2 track 10

  (assuming 10.0.0.2 ip peering from inside the ip address of the router to HO)

  Route outside 10.10.10.0 255.255.255.0 xxx.xxx.xxx.xxx 254

  (value of 254 is a more expensive route to go via IPSec tunnel and x = the bridge by default-ISP)

  ALS 99 monitor

  type echo protocol ipIcmpEcho 10.10.10.254 inside interface

  NUM-package of 3

  frequency 10

  Annex monitor SLA 99 life never start-time now

  track 10 rtr 99 accessibility

  Let me know, if this can help.

  Thank you

  Rizwan James

• Card crypto applied to the Vlan Interface of the 1841 router

  Currently, our 1841 router has a T1 connected to the WIC T1, Comcast Cable connected to Fa0/0 and the local network connected to Fa0/1.  Tuesday, our 1841 will have an ethernet connection to a new gateway router instead of use the WIC T1.  I added a 4-port ethernet module to the router in the anticipation of this change.  Since the 4-port module is not layer 3 capable, I created a virtual local area network so that I can address the Vlan with the IP address that has been previously configured on the WIC T1.  My goal is to move our IPSec vpn tunnel interface series interface vlan newly created.  I was able to add all orders of the interface vlan, but I wanted to make sure that when the time comes to make the transition, the tunnel will be actually get when it is configured on an interface vlan that is then assigned to one of the four ethernet ports in the add-on.  Has anyone done this or seen that fact?  Potential drawbacks?  Thank you very much!

  Hello

  Crypto-map is compatible with the IVR, so if everything else is in place, it does not work.

  HTH

  Laurent.

• Two RV016, gateway to gateway, routing over VPN

  Hello

  I have two RV016, I have a vpn connection from gateway to gateway between the two and I can ping computers on both sides, but I can't reach the third lan (10.0.0.0/255.0.0.0). I can join this network to routerA but not of routerB.

  My Network typology:

  

  Configuration of routers (see attachments)

  How can I configure static routes on router B?

  I tried to do, but it does not work (see RouterB_routing.jpg)

  Can someone help me?

  Thank you.

  Krzysztof,

  
  

  Unfortunately the rv016 you cannot make static through the vpn tunnel routes as it isn't an ipsec interface in the static routes section of the router.  This is normal, the router will recognize that the default setting of lan in the vpn tunnel.

  
  

  You need to business routers to make the static routes through the ipsec tunnel.

• Two links one for VPN Site to Site and another for internet on the same router configuration

  Hi all

  I have 2 internet links an ADSL and lease terminated on the same router. I need to configure ADSL for VPN site-to-site of HO and internet leased line dedicated for all users.

  my site IP subnet is 10.10.100.0/24 and HO subnet is 10.1.0.0/24.   Please find attached Config and advice it will be OK and works fine

  Thanks in advance...

  Mikael

  Hello

  For me, it looks like it has configured the route correctly;

  ip route 0.0.0.0 0.0.0.0 fastethernet4 -> for all traffic to the internet.

  Road 10.1.0.0 ip 255.255.255.0 Dialer1 -> for vpn traffic to HO.
  

  The public_IP_HO must be defined according to the map of encryption using the set by the peers command.

  I want to add is on the isakmp policy hash attribute, you can choose between sha/md5 or whatever available on your device. Make sure that the isakmp policy to match political isakmp of your HO.

  The other thing is the acl for the internet. You may want to consider replacing the deny statement if you want to deny traffic only to your jar currently it is said to deny all traffic 10.10.100.0 10.0.0.0 network, not to the 10.1.0.0 HO (network).

  HTH,

• ASA VPN missing routes

  Hi and thanks for reading.

  I'm trying to configure IPSec VPN on the SAA. The initial phase was successful - I applied the certificate, anyconnect images, etc. and thus can connect to the gateway. The problem I face is that I can not reach one of VLAN internal, or I can't go outside... Any tips are appreciated, as I am running out of ideas.

  The ASA configuration is as follows:

  ASA 9.1 Version 2
  !
  ASA host name
  activate the password * encrypted
  names of
  local pool VPN_POOL 10.194.0.10 - 10.194.0.100 255.255.254.0 IP mask
  !
  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  IP 123.44.120.22 255.255.255.248 watch 123.44.120.21
  !
  interface GigabitEthernet0/1
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/1.90
  VLAN 90
  nameif bn_management
  security-level 100
  IP 10.192.0.1 255.255.255.0 watch 10.192.0.2
  !
  interface GigabitEthernet0/1.100
  VLAN 100
  main nameif
  security-level 60
  IP 123.45.139.254 255.255.252.0 watch 123.45.139.253
  !
  interface GigabitEthernet0/1,110
  VLAN 110
  nameif vpn
  security-level 60
  IP 10.194.0.1 255.255.254.0 watch 10.194.0.2
  !
  interface GigabitEthernet0/1.120
  VLAN 120
  nameif v120
  security-level 70
  IP 10.194.2.1 255.255.254.0 watch 10.194.2.2
  !
  interface GigabitEthernet0/1,130
  VLAN 130
  nameif v130
  security-level 70
  IP 10.194.4.1 255.255.254.0 watch 10.194.4.2
  !
  interface GigabitEthernet0/1,200
  VLAN 200
  nameif v200
  security-level 40
  IP 10.196.0.1 255.255.252.0 watch 10.196.0.2
  !
  interface GigabitEthernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/6
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/7
  Failover LAN Interface Description
  !
  interface Management0/0
  management only
  nameif management
  security level 95
  IP 192.168.1.1 255.255.255.0 ensures 192.168.1.2
  !
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  permit same-security-traffic inter-interface
  network management_private object
  10.192.0.0 subnet 255.255.255.0
  network v200_public object
  Home 123.44.120.19
  network v200_private object
  subnet 10.196.0.0 255.255.252.0
  network management_services_public object
  Home 123.44.120.20
  service of the WWW_PORTS object
  tcp destination eq https service
  network v120_private object
  10.194.2.0 subnet 255.255.254.0
  network v130_private object
  10.194.4.0 subnet 255.255.254.0
  network vpn_pool object
  10.194.0.0 subnet 255.255.254.0
  network vpn_public object
  Home 123.44.120.18
  object-group network of WEB servers
  host of the object-Network 123.45.136.200
  host of the object-Network 123.45.136.202
  the UW_SOURCE object-group network
  host of the object-Network 109.74.242.9
  host of the object-Network 109.74.242.11
  the UW_DESTINATION object-group network
  host of the object-Network 123.45.139.208
  the DOMAIN_CONTROLLER object-group network
  host of the object-Network 123.45.139.205
  object-group service VPN_PORTS tcp - udp
  port-object eq 1701
  EQ port 1723 object
  port-object eq 500
  EQ object of port 443
  port-object eq 50
  port-object eq 4500
  port-object eq 47
  the INTERNAL_SUBNETS object-group network
  Description object-group for internal subnets
  object-network 10.192.0.0 255.255.255.0
  network-object 10.196.0.0 255.255.252.0
  network-object 10.194.2.0 255.255.254.0
  network-object 10.194.4.0 255.255.254.0
  object-group network the Super USERS
  host of the object-Network 123.45.136.76
  host of the object-Network 123.45.136.80
  the v120_VLAN object-group network
  network-object 10.194.2.0 255.255.254.0
  the v120_SOURCES object-group network
  host of the object-Network 123.45.136.24
  the v130_VLAN object-group network
  network-object 10.194.4.0 255.255.254.0
  the v130_SOURCES object-group network
  host of the object-Network 123.45.136.76
  host of the object-Network 123.45.139.125
  host of the object-Network 123.45.136.129
  host of the object-Network 123.45.136.83
  host of the object-Network 123.45.136.10
  MAIN_IN list extended access allowed icmp object-group SUPER INTERNAL_SUBNETS a group of objects
  MAIN_IN list extended ip access allow the SUPER object-group INTERNAL_SUBNETS group of objects
  MAIN_IN list extended access permitted ip object-group v130_SOURCES-group of objects v130_VLAN
  MAIN_IN list extended access permitted ip object-group v120_SOURCES-group of objects v120_VLAN
  MAIN_IN list extended access deny ip any object-group INTERNAL_SUBNETS
  MAIN_IN of access allowed any ip an extended list
  access-list v200_IN note v200 TRAFFIC
  v200_IN list extended access permit icmp any one
  v200_IN list extended access permit tcp any object-group servers WEB eq www
  v200_IN list extended access permit tcp any object-group eq https WEB servers
  v200_IN of access allowed any ip an extended list
  Allow NETFLOW_HOSTS to access extensive ip list a whole
  access-list to note ALLOWED INCOMING TRAFFIC
  to the allowed extended access list icmp any object-group of WEB servers
  to the allowed extended access list tcp any object-group eq www WEB servers
  to the allowed extended access list tcp any object-group eq https WEB servers
  to allowed extended access list tcp any object-group objects VPN_PORTS DOMAIN_CONTROLLER-group
  to the list of allowed extensive access udp any object-group DOMAIN_CONTROLLER-group of VPN_PORTS objects
  access-list be extended permitted tcp object-group objects UW_DESTINATION eq 5000 UW_SOURCE-group
  access-list be extended permitted udp object-group objects UW_DESTINATION eq 5000 UW_SOURCE-group
  v130_IN of access allowed any ip an extended list
  v120_IN of access allowed any ip an extended list
  access-list VPN_IN note authorized vpn traffic
  VPN_IN list of allowed ip extended access any external interface
  VPN_IN of access allowed any ip an extended list
  pager lines 24
  Enable logging
  timestamp of the record
  information recording console
  asdm of logging of information
  the logging queue 0
  main host 123.45.136.30 record
  Debugging trace record
  message 313001 debug level logging
  message 713130 level of registration information
  message 713257 level of registration information
  registration of notifications of message 713228 level
  registration of notifications of message 713184 level
  flow-export destination main 123.45.136.30 2055
  timeout-rate flow-export model 1
  time of flow-export flow - create 60
  Outside 1500 MTU
  bn_management MTU 1500
  MTU 1500 main
  MTU 1500 VPN
  V120 MTU 1500
  v130 MTU 1500
  V200 MTU 1500
  management of MTU 1500
  failover
  primary failover lan unit
  FAILOVER_LINK GigabitEthernet0/7 failover LAN interface
  failover UI FAILOVER_LINK 172.16.0.1 ip 255.255.255.0 ensures 172.16.0.2
  the interface of the monitor bn_management
  the interface of the primary monitor
  Monitor-interface vpn
  the v120 monitor interface
  the v130 monitor interface
  the v200 monitor interface
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any vpn
  ASDM image disk0: / asdm-731 - 101.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (bn_management, outside) source Dynamics management_private management_services_public
  NAT (v200, external) source Dynamics v200_private v200_public
  NAT (v120, external) source Dynamics v120_private management_services_public
  NAT (v130, external) source Dynamics v130_private management_services_public
  NAT (vpn, external) source Dynamics vpn_pool vpn_public
  Access-group compellingly in external interface
  Access-group MAIN_IN in the main interface
  Access-group interface vpn VPN_IN
  Access-group v120_IN in interface v120
  Access-group v130_IN in interface v130
  Access-group v200_IN in interface v200
  Route outside 0.0.0.0 0.0.0.0 123.44.120.17 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  WebVPN
  SVC request to enable default svc
  AAA-server BN_AAA protocol ldap
  AAA-server (main) 123.45.139.201 BN_AAA
  Timeout 5
  Server auto-type detection
  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 10.192.0.0 255.255.255.0 bn_management
  Main host community 123.45.136.30 SNMP server *.
  No snmp server location
  No snmp Server contact
  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  TRENDMICRO crypto ca trustpoint
  Terminal registration
  domain name full vpn.asa - gw.co
  subject name CN = vpn.asa - gw.co, OR =, O = some, L = some, ST = some, C = GB
  VPN_SERVICE key pair
  Configure CRL
  Crypto ca trustpoint ASDM_TrustPoint0
  Terminal registration
  Configure CRL
  Crypto ca trustpoint ASDM_TrustPoint1
  Terminal registration
  Configure CRL
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  name of the object CN = 10.192.0.1, CN = ASA
  Configure CRL
  trustpool crypto ca policy
  TRENDMICRO crypto ca certificate chain
  certificate 34cc4cb00ae501b8
  308204cd...
  quit smoking
  certificate ca 5b469990ec759d34
  30820478...
  quit smoking
  string encryption ca ASDM_TrustPoint0 certificates
  certificate ca 272b67229745d2438bf9774186aebd
  3082069c...
  quit smoking
  string encryption ca ASDM_TrustPoint1 certificates
  certificate ca 00bb401c43f55e4fb0
  308205ba...
  quit smoking
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate of 590c 2254
  308202ea...
  quit smoking
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 activate out of service the customer port 443
  trustpoint to ikev2 crypto TRENDMICRO remote access
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 123.45.138.202 255.255.255.255 bn_management
  SSH 10.192.0.0 255.255.255.0 bn_management
  SSH 123.45.136.0 255.255.252.0 main
  SSH 123.45.138.202 255.255.255.255 main
  SSH 123.45.138.202 255.255.255.255 management
  SSH timeout 10
  SSH version 2
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  access to the administration bn_management
  dhcpd dns 123.45.1.180 123.44.2.1
  !
  dhcpd address 10.192.0.200 - 10.192.0.230 bn_management
  bn_management enable dhcpd
  !
  dhcpd address 10.194.3.200 - 10.194.3.230 v120
  dhcpd enable v120
  !
  dhcpd address 10.196.0.32 - 10.196.1.31 v200
  !
  management of 192.168.1.3 - 192.168.1.254 addresses dhcpd
  !
  a basic threat threat detection
  host of statistical threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP 123.45.1.160 Server
  NTP 123.44.2.160 Server
  NTP 123.45.1.164 Server
  NTP 123.44.2.164 Server
  SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
  Trust ASDM_Launcher_Access_TrustPoint_0 bn_management vpnlb-ip SSL-point
  SSL-trust ASDM_Launcher_Access_TrustPoint_0 bn_management point
  SSL-trust TRENDMICRO out point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.05182-k9.pkg 1
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.05182-k9.pkg 2
  AnyConnect image disk0:/anyconnect-linux-3.1.05182-k9.pkg 3
  AnyConnect profiles BN_VPN_client_profile disk0: / BN_VPN_client_profile.xml
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_BN_VPN group strategy
  attributes of Group Policy GroupPolicy_BN_VPN
  WINS server no
  value of 123.45.1.1 DNS server 123.44.2.1
  L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
  value by default-domain asa - gw.co
  WebVPN
  AnyConnect value BN_VPN_client_profile type user profiles
  admin EoGC0ChIqyj0NIb5 encrypted privilege 15 password username
  rzachlod LnL.KcibQZ1OMF/d username encrypted password
  type tunnel-group BN_VPN remote access
  attributes global-tunnel-group BN_VPN
  address VPN_POOL pool
  Group Policy - by default-GroupPolicy_BN_VPN
  tunnel-group BN_VPN webvpn-attributes
  enable BN_VPN group-alias
  !
  class-map CX
  match any
  class-map inspection_default
  match default-inspection-traffic
  class-map NetFlow Traffic
  corresponds to the NETFLOW_HOSTS access list
  ins class-map
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  inspect the pptp
  class NetFlow Traffic
  destination 123.45.136.30 flow - create a flow-export-type of event
  flow-export-type of event all the destination 123.45.136.30
  class CX
  cxsc rescue
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:6be83997815380c8523971f8e7925de8
  : end

  The mention of VPN in the ACL refers to L2TP running on a Windows Server - I intend to replace this existing solution with IPSec to the ASA.

  The "details of the itinerary"on AnyConnect only shows the route 0.0.0.0/0. " After connecting to the ASA, I essentially ends in a black hole. I have the problem is with NAT, but after trying to sort on, I'm still stuck...

  My plan is to get VPN to work in the first instance and later to create a super users group, which allows access to the management of VLAN etc. I hope it's something trivial that I forgot, that I have set up the VPN to ASA in the past and doesn't not meet problems :/

  As always, tips are greatly appreciated!

  You can use an IP address for this traffic if you wish. And you can combine the NAT statements in a single statement. The config might look like this:

   object network PAT-OUTSIDE host a.b.c.23 nat (any,outside) after-auto source dynamic any PAT-OUTSIDE 

• Questions of implementation of VPN IPSec 887-> srp527

  Hey people,

  I have a few problems to an ipsec tunnel between a cisco 887VA router and a cisco srp527w router.

  I have a few books and some example materials. I worked through many combinations of what I had and I'm still a bit hard.

  I look at the results of debugging and it seems that policies do not correspond between devices:

  05:44:37.759 Jul 23: ISAKMP (0): received packet of 500 Global 500 (R) sport dport XXX.XXX.XXX.XXX MM_NO_STATE

  broute1 #.

  05:44:57.079 Jul 23: ISAKMP: (0): purge SA., his 85247558, delme = 85247558 =

  broute1 #.

  05:45:17.031 Jul 23: ISAKMP (0): received packet of XXX.XXX.XXX.XXX dport 500 sport 500 global (N) SA NEWS

  05:45:17.031 Jul 23: ISAKMP: created a struct peer XXX.XXX.XXX.XXX, peer port 500

  05:45:17.035 Jul 23: ISAKMP: new position created post = 0x8838C3F8 peer_handle = 0x800021CF

  05:45:17.035 Jul 23: ISAKMP: lock struct 0x8838C3F8, refcount 1 to peer crypto_isakmp_process_block

  05:45:17.035 Jul 23: ISAKMP: 500 local port, remote port 500

  05:45:17.035 Jul 23: ISAKMP: (0): insert his with his 87 84664 = success

  05:45:17.035 Jul 23: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH

  05:45:17.035 Jul 23: ISAKMP: (0): former State = new State IKE_READY = IKE_R_MM1

  Jul 23 05:45:17.035: ISAKMP: (0): treatment ITS payload. Message ID = 0

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID seems the unit/DPD but important shift 0

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID is DPD

  05:45:17.035 Jul 23: ISAKMP: (0): no pre-shared with XXX.XXX.XXX.XXX!

  05:45:17.035 Jul 23: ISAKMP: analysis of the profiles for xauth...

  05:45:17.035 Jul 23: ISAKMP: (0): audit ISAKMP transform against the policy of priority 1 0

  05:45:17.035 Jul 23: ISAKMP: type of life in seconds

  05:45:17.035 Jul 23: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0 x 53

  05:45:17.035 Jul 23: ISAKMP: DES-CBC encryption

  05:45:17.035 Jul 23: ISAKMP: SHA hash

  05:45:17.035 Jul 23: ISAKMP: pre-shared key auth

  05:45:17.035 Jul 23: ISAKMP: default group 1

  05:45:17.035 Jul 23: ISAKMP: (0): free encryption algorithm does not match policy.

  05:45:17.035 Jul 23: ISAKMP: (0): atts are not acceptable. Next payload is 0

  05:45:17.035 Jul 23: ISAKMP: (0): no offer is accepted!

  Jul 23 05:45:17.035: ISAKMP: (0): phase 1 SA policy is not acceptable! (local YYY. YYY. YYY. Remote YYY

  XXX.XXX.XXX.XXX)

  05:45:17.035 Jul 23: ISAKMP (0): increment the count of errors on his, try 1 of 5: construct_fail_ag_init

  Jul 23 05:45:17.035: ISAKMP: (0): could not build the message information AG.

  Jul 23 05:45:17.035: ISAKMP: (0): send package to XXX.XXX.XXX.XXX my_port 500 peer_port 500 (R) MM_NO_STATE

  05:45:17.035 Jul 23: ISAKMP: (0): sending a packet IPv4 IKE.

  05:45:17.035 Jul 23: ISAKMP: (0): the peer is not paranoid KeepAlive.

  05:45:17.035 Jul 23: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (peer

  XXX.XXX.XXX.XXX)

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID seems the unit/DPD but important shift 0

  Jul 23 05:45:17.035: ISAKMP: (0): load useful vendor id of treatment

  Jul 23 05:45:17.035: ISAKMP: (0): provider ID is DPD

  05:45:17.035 Jul 23: ISAKMP (0): action of WSF returned the error: 2

  05:45:17.035 Jul 23: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE

  05:45:17.035 Jul 23: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

  05:45:17.039 Jul 23: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (peer

  XXX.XXX.XXX.XXX)

  05:45:17.039 Jul 23: ISAKMP: Unlocking counterpart struct 0x8838C3F8 for isadb_mark_sa_deleted(), count 0

  05:45:17.039 Jul 23: ISAKMP: delete peer node by peer_reap for XXX.XXX.XXX.XXX: 8838C3F8

  05:45:17.039 Jul 23: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL

  05:45:17.039 Jul 23: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_DEST_SA

  Here is a slightly adjusted version of my run-fig (came out I was sure that no one would need things) and attached are screenshots of IPSec and IKE Policy of the srp527w strategy

  version 15.1

  hostname broute1

  !

  logging buffered 65535

  information recording console

  !

  No aaa new-model

  !

  iomem 10 memory size

  clock timezone estimated 10 0

  Crypto pki token removal timeout default 0

  !

  !

  IP source-route

  !

  !

  !

  !

  VDSL controller 0

  operation mode adsl2 Annex A

  !

  property intellectual ssh version 2

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  lifetime 28800

  ISAKMP crypto key PRE_SHARED_KEY_FOR_IKE (I_THINK) REMOTE_HOST hostname

  !

  !

  Crypto ipsec transform-set JWRE_BW-1 esp-3des esp-sha-hmac

  !

  !

  !

  IPSec-isakmp crypto 10 JWRE_BW-1 card

  defined peer XXX.XXX.XXX.XXX

  game of transformation-JWRE_BW-1

  match address 101

  !

  interface Loopback0

  no ip address

  !

  ATM0 interface

  Description - between node ADSL-

  no ip address

  no ip route cache

  load-interval 30

  No atm ilmi-keepalive

  !

  point-to-point interface ATM0.1

  no ip route cache

  PVC 8/35

  TX-ring-limit 3

  aal5snap encapsulation

  PPPoE-client dial-pool-number 1

  !

  !

  interface Vlan1

  Management Interface Description

  address IP AAA. AAA. AAA. AAA 255.255.255.0

  IP mtu 1452

  IP nat inside

  IP virtual-reassembly in

  no ip-cache cef route

  IP tcp adjust-mss 1420

  !

  interface Dialer1

  Description BETWEEN NŒUD ADSL-

  MTU 1492

  the negotiated IP address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  IP virtual-reassembly in

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP chap hostname ADSL_USERNAME

  PPP chap password 7 ADSL_PASSWORD

  PPP ipcp dns request accept

  No cdp enable

  card crypto JWRE_BW-1

  !

  recording of debug trap

  access-list 101 permit ip 192.168.7.0 0.0.0.255 10.0.1.0 0.0.0.255

  Dialer-list 1 ip protocol allow

  Some specific questions:

  (1) on the PSR in the example I used (and I have a few PRS-> RPS VPN work) I see you enter the pre-shared key, I do not see in the examples I've used something on the IKE pre-shared key on the box of IOS. Does anyone have examples where you use the pre-shared for IKE? I wonder if it is my main problem as clearly says the newspaper there is no pre-shared key :|

  (2) I used a mash of names between different sections mish as on ESP the naming convention is not the same thing; IE: what parts of the IPSEC negotiation come from IKE policy and including the IPSEC policy section section. The names really matter across different ends of the VPN?

  (3) I noticed when I run this command in the(config-crypto-map): #

  defined peer FQDN

  It is converted to:

  defined peer XXX.XXX.XXX.XXX

  Should it? I want the camera to watch the FQDN that this particular host using DDNS and do not use a static IP address.

  I could ask 1 million questions, but I'll leave it for there, if anyone can see anything out (or can answer Q1 in particular) please let me know.

  Thanks in advance for your time and help people.

  B

  The IKE policy doesn't seem to match, you must configure the corresponding IKE policy on the router as follows:

  crypto ISAKMP policy 10

  the BA

  sha hash

  preshared authentication

  Group 1

  lifetime 28800

  For the preshared key, use the address instead of the host name:

  crypto isakmp key address

• Client VPN Cisco router Cisco, MSW CA + certificates

  Dear Sirs,
  Let me approach you on the following problem.

  I wanted to use a secure between the Cisco VPN client connection
  (Windows XP) and Cisco 2821 with certificate-based authentication.
  I used the Microsoft certification authority (Windows 2003 server).
  Cisco VPN client used eTokenPRO Aladdin as a certificate store.

  Certificate of MSW CA registration and implementation in eToken ran OK
  Customer VPN Cisco doesn't have a problem with the cooperation of eToken.
  Certificate of registration of Cisco2821 MSW ca ran okay too.

  Cisco 2821 configuration is standard. IOS version 12.4 (6).

  Attempt to connect to the client VPN Cisco on Cisco 2821 was
  last update of the error messages:

  ISAKMP: (1020): cannot get router cert or routerdoes do not have a cert: had to find DN!
  ISAKMP: (1020): ITS been RSA signature authentication more XAUTH using id ID_FQDN type
  ISAKMP (1020): payload ID
  next payload: 6
  type: 2
  FULL domain name: cisco - ca.firm.com
  Protocol: 17
  Port: 500
  Length: 25
  ISAKMP: (1020): the total payload length: 25
  ISAKMP (1020): no cert string to send to peers
  ISAKMP (1020): peer not specified not issuing and none found appropriate profile
  ISAKMP (1020): Action of WSF returned the error: 2
  ISAKMP: (1020): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  ISAKMP: (1020): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

  Is there some refence where is possible to find some information on
  This problem? There is someone who knows how to understand these mistakes?
  Thank you very much for your help.

  Best regards
  P.Sonenberk

  PS Some useful information for people who are interested in the above problem.

  Address IP of Cisco 2821 10.1.1.220, client VPN IP address is 10.1.1.133.
  MSW's IP 10.1.1.50.
  Important parts of the Cisco 2821 configuration:

  !
  cisco-ca hostname
  !
  ................
  AAA new-model
  !
  AAA authentication login default local
  AAA authentication login sdm_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization sdm_vpn_group_ml_1 LAN
  !
  ...............
  IP domain name firm.com
  host IP company-cu 10.1.1.50
  host to IP cisco-vpn1 10.1.1.133
  name of the IP-server 10.1.1.33
  !
  Authenticated MultiLink bundle-name Panel
  !
  Crypto pki trustpoint TP-self-signed-4097309259
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 4097309259
  revocation checking no
  rsakeypair TP-self-signed-4097309259
  !
  Crypto pki trustpoint company-cu
  registration mode ra
  Enrollment url http://10.1.1.50:80/certsrv/mscep/mscep.dll
  use of ike
  Serial number no
  IP address no
  password 7 005C31272503535729701A1B5E40523647
  revocation checking no
  !
  TP-self-signed-4097309259 crypto pki certificate chain
  certificate self-signed 01
  30820249 308201B 2 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  .............
  FEDDCCEA 8FD14836 24CDD736 34
  quit smoking
  company-cu pki encryption certificate chain
  certificate 1150A66F000100000013
  30820509 308203F1 A0030201 02020 HAS 11 092A 8648 01000000 13300 06 50A66F00
  ...............
  9E417C44 2062BFD5 F4FB9C0B AA
  quit smoking
  certificate ca 51BAC7C822D1F6A3469D1ADC32D0EB8C
  30820489 30820371 A0030201 BAC7C822 02021051 D1F6A346 9D1ADC32 D0EB8C30
  ...............
  C379F382 36E0A54E 0A6278A7 46
  quit smoking
  !
  ...................
  crypto ISAKMP policy 30
  BA 3des
  md5 hash
  authentication rsa-BA
  Group 2
  ISAKMP crypto identity hostname
  !
  Configuration group customer isakmp crypto Group159
  key Key159Key
  pool SDM_POOL_1
  ACL 100
  !
  the crypto isakmp client configuration group them
  domain firm.com
  pool SDM_POOL_1
  ACL 100
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac 3DES-MD5
  !
  crypto dynamic-map SDM_DYNMAP_1 1
  the transform-set 3DES-MD5 value
  market arriere-route
  !
  card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
  map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
  client configuration address map SDM_CMAP_1 crypto answer
  map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
  !
  ................
  !
  end

  status company-cu of Cisco-ca #show cryptographic pki trustpoints
  Trustpoint company-cu:
  Issuing CA certificate configured:
  Name of the object:
  CN = firm-cu, dc = company, dc = local
  Fingerprint MD5: 5026582F 8CF455F8 56151047 2FFAC0D6
  Fingerprint SHA1: 47B 74974 7C85EA48 760516DE AAC84C5D 4427E829
  Universal router configured certificate:
  Name of the object:
  host name = cisco - ca.firm.com
  Fingerprint MD5: E78702ED 47D5D36F B732CC4C BA97A4ED
  Fingerprint SHA1: 78DEAE7E ACC12F15 1DFB4EB8 7FC DC6F3B7E 00138
  State:
  Generated keys... Yes (general purpose, not exportable)
  Authenticated issuing certification authority... Yes
  Request certificate (s)... Yes

  Cisco-ca #sh crypto pubkey-door-key rsa
  Code: M - configured manually, C - excerpt from certificate

  Name of code use IP-address/VRF Keyring
  C Signature name of X.500 DN default:
  CN = firm-cu
  DC = company
  DC = local

  C signature by default cisco-vpn1

  IMPORTANT: I don't have a Cisco IOS Software: 12.4 (5), 12.3 (11) T08, 12.4 (4.7) PI03c,.
  12.4 (4.7) T - there is error in the cryptographic module.

  Hey guys, it's weird that the router is not find cert after IKE is the cert and validates, it is certainly not reason, but I would go ahead and set up the mapping of certificate on this router to force the client to associate with Group of IKE, for that matter, that you need to change your config a bit for use iskamp profiles :

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_isakp.html

• VPN gateway with the traffic filtering

  I work in his laboratory on a configuration on a small scale in which client PC establishes an IPSEC VPN with Cisco 1921 router, I have two questions in this regard.

  (1) for wireless PC clients, uses an IPSEC VPN Client the best option or should I prefer other options. wireless clients also use Radius Server for authentication.

  (2) I want to make sure no other traffic can reach or pass the interface of local network other than the VPN Client traffic, I need to set up on the router to make sure that no other traffic cannot pass other than traffic APV.

  First: The real IPsec VPN client is the AnyConnect. The VPN-config for AnyConnect (especially for IPsec) gateway on the router IOS is much more difficult, so it's on the SAA. If you still have the possibility of changing the front doors, then go for a SAA. It is also much cheaper from a perspective of license given that no license of AnyConnect Essentials for the router. The Cisco VPN Client to the traditional address is EOL and should not begin a new deployment on this basis.

  Your questions:

  (1) all VPN - users should be authenticated in some way. Send the request to a central directory authentication is a best practice and usually done with RADIUS. In addition to authentication, you can also perform an authorization to control what rights Gets a VPN user.

  (2) If you only want to allow IPsec traffic, you must configure an access list, a permit for UDP/500, UDP/4500 and IP/50 of your router IP. With this config, all other traffic will be dropped.

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

  Hello

  Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

  The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

  Please, what missing am me?

  A few exits:

  ISAKMP crypto to show her:

  isakmp crypto #show her

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  Crypto ipsec to show her:

  Interface: GigabitEthernet0/0

  Tag crypto map: QRIOSMAP, local addr 62.173.32.122

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

  current_peer 62.173.32.50 port 500

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  #pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0

  #pkts not unpacked: 0, #pkts decompress failed: 0

  Errors #send 0, #recv 0 errors

  local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

  Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

  current outbound SPI: 0x4D7E4817 (1300121623)

  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:

  SPI: 0xEACF9A (15388570)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

  calendar of his: service life remaining (k/s) key: (4491222/1015)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  Please see my config:

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  encryption... isakmp key address 62.X.X... 50

  ISAKMP crypto keepalive 10 periodicals

  !

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

  !

  QRIOSMAP 10 ipsec-isakmp crypto map

  peer 62.X.X set... 50

  transformation-TS-QRIOS game

  PFS group2 Set

  match address 100

  !

  !

  !

  !

  !

  interface GigabitEthernet0/0

  Description WAN CONNECTION

  62.X.X IP... 124 255.255.255.248 secondary

  62.X.X IP... 123 255.255.255.248 secondary

  62.X.X IP... 122 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  card crypto QRIOSMAP

  !

  interface GigabitEthernet0/0.2

  !

  interface GigabitEthernet0/1

  LAN CONNECTION description $ES_LAN$

  address 192.168.20.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  !

  IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

  IP nat inside source list 1 pool mypool overload

  overload of IP nat inside source list 100 interface GigabitEthernet0/0

  !

  access-list 1 permit 192.168.20.0 0.0.0.255

  access-list 2 allow 10.2.0.0 0.0.0.255

  Note access-list 100 category QRIOSVPNTRAFFIC = 4

  Note access-list 100 IPSec rule

  access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

  access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

  access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

  access-list 101 deny ip any any newspaper

  access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 110 permit ip 192.168.20.0 0.0.0.255 any

  !

  !

  !

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

  Here are the things I see in your config

  I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

  IP route 0.0.0.0 0.0.0.0 62.X.X... 121

  IP route 0.0.0.0 0.0.0.0 62.172.32.121

  This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

  IP route 10.2.0.0 255.255.255.0 192.168.20.2

  In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

  IP route 172.17.0.0 255.255.0.0 Tunnel20

  IP route 172.17.2.0 255.255.255.0 Tunnel20

  And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

  IP route 172.18.0.0 255.255.0.0 Tunnel20

  IP route 172.18.0.0 Tunnel20 255.255.255.252

  HTH

  Rick

• Card Crypto GETVPN on loopback

  Hello

  We have 6 WAN routers connected through MPLS ISP cloud, we must apply GET VPN between these WAN routers.

  We have 2 servers of keys (1800 routers), and WAN routers will act as members of the Group (6 GMs)

  The configuration files are attached for work typical configuration GETVPN (crypto map applied to the WAN interface)

  In the key server configuration, the crypto isakmp command uses the WAN IP of each router WAN (172.16.x.x) address, and since KS routers are connected to the local network (VSS), they should be able to join 172.16.X.X and therefore the subnet in 172.16.X.X is announced for the local network (check GM-configuration file under eigrp - connected redist)

  That's what our customers want to avoid! they don't want 172.16.X.X to make advertising for the local network.

  I know it's possible in the configuration GETVPN to configure, the command crypto isakmp for use the loopback address of the routers WAN instead of the WAN IP address, but in this case the card encryption should be applied to address loopback, and for this, all traffic to be encrypted and decrypted to go through the loopback on all routers WAN interfaces.

  I was wondering what is the best solution in this case, I have to use the config below on GM

  card crypto-address loopback 0
  

  TEST allowed 10 route map

  set interface Loopback0

  TEST IP policy route map-local

  But I don't know if it is correct, or there may be a better idea... so I thought share with you guys to discuss all the best ideas.

  Ali,

  We do not support cryptographic cards on loopback interfaces.

  Use the crypto-local address (in the case of vanilla IPsec) card or customer record interface (even if it is for another use) order under specifcy gdoi what inetrface or VRF you want to record source to / receive to generate a new key on.

  You can take a look at DIG:

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6525/ps9370/ps7180/GETVPN_DIG_version_1_0_External.PDF

  section 4.2.1.2.3 and other talk.

  M.

• ASA does ACB support? and question site to site vpn.

  Hello.

  We must separate the traffic based on source network. It is possible to separate the network on Cisco ASA?

  or not, if we establish just the vpn lan to lan with VPN HQ device, the corresponding traffic access list back to the tunnel vpn automatically with any itinerary?

  then it's ok, but I think that Cisco ASA does not support the PBR(policy-base-routing) yet, I wonder if there is no specific route is required to report to IPSEC tunnel.

  If please attached the file review and let us know what is the best solution for our problem.

  Thanks vevery one

  Not quite sure what you mean by:

  conclusion, even through the same destination, the Card Crypto (static route not set to the specific) will be launched first that the normal delivery?

  If you have the static route on the SAA to a remote subnet / destination via a different interface of VPN, so he's not another. It will check the routing in this instance.

  Pls check if you have static route on the SAA for the destination network to a different interface that where ends the VPN.

• Site to site VPN (ASA-> router IOS, with two interfaces) help

  Dear,

  I need help to configure VPN from Site to Site of cisco ASA to the IOS router, the router has 2 WAN links, a primary and secondary backup.

  There was only a single week of link there is, now we have installed the second link as a backup, we use OSPF as the routing protocol.

  VPN with simple link worked fine, now, when the main link fails the network is down.

  Waiting for response.

  There is an easy solution.  On the router, you must terminate the VPN on the loopback interface.

  something like this:

  interface lo0

  IP x.x.x.x where x.x.x.x

  card crypto-address lo0

  interface wan_1

  vpn crypto card

  interface wan_2

  vpn crypto card

  One condition is that the loopback interface has accessible by the device of the SAA.