raid question 6 UCS 210

Similar Questions

• UCS 210 - HDD not able to configure

  Hi all

  I am faced with the question in UCS 210 Server. One of the hard drive no is not configured correctly because of this I am facing problem to configure the raid.

  When I opened the Webbios I got the following error. Please suggest how to proceed further.

  

  Hello

  This part of HARD drive RAID another array?

  If you want to add the existing hard drive RAID 6 - Virtual Drive, then you must clear the foreign configuration and add it.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/SW/RAID/configuration/guide/MegaRAID.html#wp1058098

  Padma

• UCS 210 M2 RAID and VMWARE

  Hello"

  I have cisco UCS 210 M2 Server with 10 GB HD 140, I insert new HD and I have rebuilt the RAID, but when I installed Vmware 5.0 Server could not see the Vmware.

  See the attached picture, what this message is relarted

  Nice, please mark the thread as 'responded' so that in the future, users can see that you have solved your problem and the steps to get there, we took.

  -Kenny

• UCS C220 M3 raid question

  Hi all

  I have a UCS C220 M3 with 4 hard drives, when I want to create the Raid 5 is not enabled, I have only 1 or 10.

  Any ideas?

  Thank you.

  See this http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C220/ins...

  You need the software key, otherwise you will only be able to configure RAID 0,1 and 10

  "You can override this support by adding support of SAS RAID 5 with optional software key. See installing a key Module of software RAID for Embedded RAID 5 screens. »

  HTH,

  -Kenny

• Question on UCS C series

  Hello

  I have a question about the series C UCS. Is it possible that some now to connect to 6120 fabric Manager and manage as the blade series. Or are they only manageable through their port MMIC.

  In depth.

  The 1.3.x of the code, it is not possible.  This feature will be available in 1.4 which is just QA and should be available next month.

  Kind regards

  Robert

• Configuration RAID - on Cisco UCS C 220 M3 with controller RAID UCSC-RAID-11-C220 problem.

  Dear all,

  Hope everything is going well...

  Here is the error I encountered during the installation:

  While Installting and UCS C220 M3s server configuration & initially map is with card UCSC-RAID-MZ that supports RAID 0/1/10.

  Now I replaced it with UCSC-RAID-11-C220 mezzanine card so that it supports RAID 0/1/5/10/50.

  But when I opened the MMIC for the server & again, it is show that it supports only RAID 0/1/10...

  Please find the spare part for your reference.

  I have to activate or configure additional options on the BIOS to support RAID 5 Server?

  Looking forward to hear from you! Thanks in advance...

  Kind regards

  Gopi G

  Please mark the thread as "answered" for future users to see that you found the solution and if possible share the info for others facing the same issue.

  -Kenny

• Another RAID Question :)

  Until recently, we bought our licenses for ESXi 5 and before I have order my raid controller I would check with the community on certain things.

  Based on research I did on the forums and on the compatibility list, it's a pretty decent controller:

  http://www.Newegg.com/product/product.aspx?item=N82E16816118170

  What we seek to do is to take the above 8 port controller and set up 4 disks in RAID 10. Then down the line, connect a 4 discs additional for the controller even in another configuration of raid 10 or two matrices RAID 1.

  So my question is this: is it possible to install ESXi 5.5 on the first RAID 10 configuration, then later, to create additional tables on the same controller and then assign them to the existing installation of ESXi?

  Thanks in advance for answers!

  Yes, you can add new bays starting from the same controller to your ESXi installation at a later date. This will be done through host Configuration > storage. Once the berries are configured, they will appear in the list of available LUNS and can be connected to ESXi like additional data stores.

  I don't have experience with this particular model of LSI first hand, but it is listed on the HCL 5.x ESXi, so you should not encounter compatibility problems.

• RAID question...

  I have two in my system RAID arrays... lies in 3 x 1 TB RAID-5 (2 TB total) which is implemented using the controller onboard Marvell chip and Intel RAID software. The second is a 4 x 2 TB drive RAID-5 (total of 6 TB) inside a box external and put in place with a G Highpoint RAID card - Tech material on a PCI-e bus.

  I plan to do a thorough cleaning and a reinstallation of the operating system and programs, and my question is, can I safely do without risk of loss of data on RAID arrays? I'm pretty confident the hardware RAID will be correct, but as software RAID is configured using a software program that is installed on the operating system, I am afraid that wiping the OS (and, therefore, control software) and do a relocation will result in this RAID being ruined... thoughts?

  Since the Marvell raid is configured in the BIOS and not in the window, unless you tried to make it REALLY slow using the Windows software, you should be OK, but if you tried to make it even slower than it should be and you used the Windows software, you will lose all your material. Is not really important, because you'll have a good backup in place strategy, I hope.

  The G-Tech raid will survive a new installation, but will still suffer from the eSATA connection. I think it would be a good time to add a dedicated raid controller to improve your performance.

• W700 RAID question

  My W700 is almost 4 years and service policy was released last December.

  Yesterday, the Console matrix Intel has indicated one of the disks RAID 1 (drive 0) had failed and is in mode "gradient".

  I got a new spare drive which I installed it and the table was being rebuilt.

  Somewhere after 60% (possibly after complete reconstruction), the array returned in mode "Gradient" with drive 0 showing again failed. The same drive I just replace it with a new one (rebuilt/unused).

  I'm probably looking to two HD failures or possible failure in the HD on the motherboard, BIOS RAID support?

  I won't buy another HD if it's not necessary?

  The W700 supports any flavor of SSD (no raid configuration)?

  I might consider a RAID SSD not because otherwise, the W700 has been flawless.

  Opportunities and guidance appreciated.

  J

  I found, I got another piece of spare and it seems to work very well. I guess that the first replacement was also defective. What are the chances of that? I also ran PC diags (bootable) DR BACK on the two disks and they extracted good.
  J

• question of UCS code main F0283 and dce interface and chassis number?

  Dear Sir

  Introductions:

  a 6120 connect chassis 1 a 2104-1 and frame 2 2104-1 post

  frame 1 have sever 3/4/5/6/7/8 (all breaking is B200 M3, two 2104)

  2 chassis have cut 1/2/3/4/5/7 (cut 1/2/3/4 is B200 M3, two 2104)

  question

  1. main code F0283

  all servers have master code F0283, but everything still break can use.what it? How I did it?

  affected object:sys/chassis-1/blade-6/fabric-A/path-1/vc-722

  Description: a - 722 bright 1/6 ether down, reason: unknown

  frame 1 have sever 3/4/5/6/7/8

  2 chassis have cut 1/2/3/4/5/7

  I stop all and, on the other hand, begins the problem also.

  affected

  I stop all and, on the other hand, begins the problem also.

  

  

  

  2. on frame 1 sever-1 adapter 1 dce interface (interface 1 dce and dce 5)

  one of ony uses?

  

  3.
  frame 1 have sever 3/4/5/6/7/8
  2 chassis have cut 1/2/3/4/5/7

  but I reboot,.

  2 chassis have sever 3/4/5/6/7/8
  frame 1 have cut 1/2/3/4/5/7

  If the profile is cloudy

  I have shtdown all, and start 1 ok, chassis chassis later 2

  the problem is ok... what this?

  

  Hello

  #1 F0283 - NHS source pinning failed

  Please make sure that necessary VLANs that are allowed in vNIC is created in FI and and allowed in the uplinks.

  #2 link down errors

  These are normal if the blades are not up and running with an operating system (with appropriate drivers).

  Padma

• SSD 4 k mount Raid Question

  In recent months the couple here, I built a fairly large ediitng platform k 4. now my only neck of the bottle is what I believe to be my camera 2. Is raid 0 but the speed is even slower, so I only for the 4 k files r3d that I am editing in first pro. I was chatting on upgrade to 2 1 TB samsung 850 pro ssd in raid 0 as the source media players. I see a significant increase on my flow with these discs for the media source?  The rest of the system is a x 5960 i7, titan x, 256 GB ssd for cache files, a 256 GB m2 for start-up and a 99 deluxe 3.1 x mobo.

  -Cheers

  This test seems very strange, as if they had a bad intel 750 or it is in a location PCIe clocked at 1 x. I wouldn't trust these results, sound out of the character. I've seen other landmarks, most of anandtech, which show that the drive intel is preferable to writing, while the samsungs are better at reading.

  This shows the intel 750 and the cards just to get the samsung 850 pro as well. in some of the benchmarks, you might imagine a raid of samsung 850 pro becomes a bit near the 750 in reading/writing, but raid will not make the difference in latency.

  Intel SSD PCIe SSD Review 750: NVMe for the customer

• Looking to replace a RAID in older (UCS-61) with a new (UCP-51) Perc 5i controller on a PowerEdge r610 server...

  Hello world

  I'm looking to get RAID 5 in an old R610 capabilities we have laying around. The new controller seems to be compatible with the server and he knows well. Whenever I start the server with the new Perc 5i card it gives me:

  "Invalid pcie card found in the internal storage location.

  System stopped! »

  Is there a step in this process I am missing? This is my first time doing something like this and get beat. If I put the old controller to back in or no controller at all, it starts without a problem. I've updated the BIOS BIOS server Dell R610 version 6.4.0.

  Any advice would be greatly appreciated.

  The PERC 5 is not supported on the R610.  You need the PERC 6 / i.  The PERC 5 might work, but you cannot use it in the location of storage dedicated; you will need to try another location PCIe.

• The T110 II RAID question server configuration

  Hello

  I have T110 II server and 3 HDD WD SATA 1 TB each.

  And RAID Controller PERC S100

  When the load on the server RAID controller card it shows 3 HDs on enacting of the host.

  During the RAID configuration with virtual disk management setting in do not show any physical hard disk.

  Pictures are attached below

  Please help me

  closed;). the H200.

• Power e410 RAID question

  Hello

  I have an R410 using a Perc H200 controller. In the frame are 3 disks. 2 are in a RAID 1 configuration and the third is alone. I just changed status from abroad online.

  What I want to do is to use this drive as a storage device independent for the 2012 operating system on the box server. Its data not important that it will contain so didn't need to be ATTACKED. However, the only option available in Openmanage shall assign as a global hot spare. great if it's what I wanted but it's not!

  I can do what I'm describing?

  Thank you very much

  Sorry Barry, I almost forgot the H200 has a capacity of passthrough. The H700 and Perc 6 controllers do not have this capacity. You should be able to insert the single disc, erase any previous configuration for this drive in the controller. Then the operating system. The operating system should be able to see this solitary drive in the disk management page.

  Let me know.

• Help - power up to Raid question R710 - the following VDs are missing 01

  IM needs assistance regarding what to do next. I have a R710 turned off and installed a new ram. Restarted and the ram is very well detected. However, I have the screen shows VD01

  The following VDs lack 01.

  Im not sure what my next step would be, and my concern is that if I go into the configuration I will wipe disks

  Any help would be really appreciated

  Brendan

  

  You can press 'F' to import and continue or start the configuration utility and import the foreign configuration.