Re: No wireless connection on Tecra A9

Similar Questions

• Tecra M5: Wireless connection is no longer working

  I have a new Toshiba Tecra M5. I originally put in place to connect to my WAP Home/office with no problems. After using it in a place where no WAP was available and making the home, wireless connection"is not available" and I can't do so.

  Additional information: I have two other systems connected to my WAP without any problem. I can connect the Toshiba to my home LAN via a cable without problems. I already rebooted the latest drivers and tried to re-establish a wireless connection completely new, without success.

  Any help would be appreciated. Thank you.

  Bob

  Hello

  Looks you used Notepad in 2 different WLANs.
  In my opinion, you should refresh the connection.
  Go to the properties of WLan, and select the wireless networks tab.

  Here, you can set the home WLAN on the preferred networks. This should be done if you have configured your WLan network as invisible. Also use the option View Wireless networks.
  If your home WLan is not in the list, then you need to add the SID of WLan.

  Usually the WAP encryption password must be redefined

• Tecra A3: Wireless connection problem

  I reinstalled windows xp prof after my laptop crashed and lost files.
  Everything works except for the wireless connection, it is turned on, but windows will not see it?

  Any ideas? I tried to download different drivers from the driver from toshiba support page, but nothing has worked.

  Hello

  When the WLAN switch is set to ON, use the FN + F8 key combination to activate the WLAN adapter. After that do what you will be able to use the wireless network card.

  Wireless network card appears correctly in the Device Manager?

• After new wifi card no wireless connection

  Hi, can all-in-one help me on this problem?

  in my tecra M 745 due youcef change a broken wifi card: the new material appears to be installed correctly, but when I return the laptop wireless connection has been configured in windows with a maximum range of 11 MB/s (a ' b') and keepes fall all the time (notmally 54 mb/s)
  When I want to set up using intel proset software, as I did before the repair (worked great), the program was empty, but the software was still in 'software': the helpdesk here said when the material is allright their work is done. they can set up but cost me a 100 euros/hour
  So, what went wrong? I think that the driver is correctly installed but intel proset does not work, why?
  should I update intel proset?
  Thanks in advance
  Dr. Weekx

  Hello Dr.

  If the wireless card is a new and correctly recognized and installed there not any problem at all. If there is a problem with the feature, it can be simply false connection configuration. Please don t be crazy about me, but installation and configuration of the Wi - Fi connection are two separate jobs. If you check the service for other stuff every step must be paid separately.

  As you know, the wireless connection can be configured using parameters of Windows or by a customer (in your case Intel one). If you want to use the software Intel configuration of Windows MUST be disabled.

  It will be nice that you give us a description of the good model laptop. Sorry, but Tecra M 745 is unclear to me. As far as I know, this is the processor identification and this processor is built in many models of different laptops.

  Good bye

• Bluetooth wireless connection

  MacBookPro OSX El Capitan; Version 10.11. Retina display - MacBookPro connects to the printer HP C6150 help electrician with no problems. not then attempt to use the bluetooth connection.

  To a printer wireless connection works using old MacBook. Bluetooth connects to the mouse and works very well.

  Select the Bluetooth device-

  The computer icon shows - not connected

  Apple mouse - connected

  Hello analyst.1,

  Thank you for using communities of Apple Support.

  I understand that you can print from your MacBook Pro to your HP using Ethernet and wireless printer, but not via Bluetooth. I know how it is important to ensure that you can connect to your printer via Bluetooth. I'll be more than happy to help you with this.

  Use OS X El Capitan: Add or remove a printerand make sure you have the latest version of the software installed and printer connection instructions, specifically, this section:

  Add a Bluetooth printer

  1. Update your software: choose the Apple menu > App Store, click updates, and then install the listed software updates. Even if no updates appear, this ensures that OS X has the latest information on printing software you can download from Apple. If you don't do this, you see a message that software is not available when you connect your printer.

     If you have a printer AirPrint, you have no need to check the software updates.

  2. Prepare your printer: use the instructions that came with your printer to unpack the printer, install the ink or toner and add paper. Turn on the printer and make sure it is not the display of errors.

  3. Connect your printer: follow the instructions that came with your printer to make sure it is ready to connect through Bluetooth. You must also make sure to activate Bluetooth and set up the printer Bluetooth as a new device.

  After connecting your printer, if you see a message prompting you to download new software, be sure to download and install it. OS X will automatically use AirPrint if your printer supports.

  Have a great day!

• How to configure a printer wireless connected to Time Capsule?

  I just bought a printer HP Color LaserJet Enterprise M577z MFP Flow. It has capabilities of wireless printing. So far, I was able to connect wirelessly to one of my MacBook Pro computers, but only by having the printer create an Ad - hoc network that allows up to 5 devices to connect to the printer. But that of not what I want because every computer should manually disconnect the Wi - Fi network, connect to the Ad hoc network, the print job and then reconnect to the Wi - Fi network whenever a print job is required. It is very difficult and frustrating.

  What I would like is striking is the printer act like a network printer by wireless connection to my Time Capsule. I can't connect the printer to the USB port of time Capsule because they are far away from each other, and I don't want to use cables throughout my place. But I have no idea on how to do it because I can't find this option in the menu of the writer or configuration of the United Nations the HP utility software.

  I hope someone here could help me, please. Thank you!

  I have an Epson printer, so some of my experiences may or may not apply.

  I also have a time Capsule, and my printer and Time Capsule are far apart.

  My current configuration looks exactly what you are looking for: a wireless network provided by Time Capsule than all my Apple devices to a wireless connection, and my printer connects to the same wireless network.

  When I first bought the Epson printer, I needed to connect it to the Capsule of time via a USB port.  This sounds as if it were true for you as well.  So, for this very short period. I moved the printer via the USB port next to the printer, the connected Time Capsule, made the setup and then the printer recognized my standard wireless network.  I've returned to steady state, which I use now, with the printer and the far (actually on different floors) Time Capsule.

• 7520 HP loses the wireless connection. What can I do?

  I've seen lots of talk about HP products, loss of wireless connection.  I have the same problem with my 7520.  Initial Setup is perfect, but he began to lose the connection when it went into standby mode.  Someone at - it a solution?

  THERE IS A FAST SOLUTION!
  On April 18, 2014 (page 11 of this thread), I posted a quick solution. My HP7520 printer has worked on Netgear router WIFI 7550 flawless since then. I suggest you read this post.
  From long experience with HP, I found they have great hardware, but their software has always been dismal. The ultimate "fix" would be for HP address their failure of a software that allows to my difficulty in working.
  A single "tweak" in the router security settings wifi will do. The rest of settings changes other people have suggested are short lived (about an hour in most cases), while they don't be reconnected unless they restart everything. It makes sense because of what is happening.
  The single "twist" parameter should logically point HP programmers to where in the firmware, there is the problem. They listen to? And, really, it doesn't matter on all other settings printer and router. All mine are back to the default settings and it all still works very well.
  Go to a BBQ and stop wasting your time on this issue.
  Ken

• wireless connectivity

  installed a wireless antenna external usb (ralink)

  everything worked fine

  disconnected the cable, the feed under the rug, reconnected

  All of a sudden the wireless disappeared

  even from the wireless receiver integrated

  tried a wireless thumb usb adapter small size

  the system recognized the adapter

  appear still no wireless connection

  in the following device manager/network adapters are listed

  Ralink 802.11n wireless LAN card

  map of Microsoft virtual wifi miniport

  realtex pcie fe family controller

  all are identified as working properly

  I need help, remedy the situation

  

  First of all, make your computer make and model and model of your wireless usb adapter.

  Then remove the said cable under the carpet... restart your router/access point and computer.

  Thirdly, check if the internal card now has a signal... plug in external usb and see if she gets a signal... run cable under carpet... Note all changes as you go through the following steps.

  Report back, come back here.

  Frank

• Very limited wireless connection

  I have a HP Pavilion dv7 - 3153ca with a 64-bit windows system 7 and I'm only able to get a wireless connection when the laptop is very close to the modem. Once the laptop is moved, for example, to another floor of the House, the connection is lost and cannot be re established until I have the back next to the modem. He has no problem with the wired connection. This has happened while he was trying to pass my McAfee security provider, although I don't think this is the problem that my other laptop (a Dell) converted without this problem. The other laptop continues to maintain its connection Wireless throughout the House, so the router and the modem is not the issue. I downloaded and re-installed the adapter without modification. I have scanned the laptop and nothing is reported in the mess. Are there any ideas as to why the wireless connection works only when the laptop remains close to the modem? Thank you.

  It seems I may not have been very clear in my previous post.  I wanted to suggest was to reverse the connection of the antenna.  As mentioned in the thread I linked, the connections might have been reversed from what they should be from the factory.  If this is the case, then connect the antennas in a factory setting would not solve the problem.

  Have you tried to reverse the antennas?  If they are in the deformities, then this would fix it.  If they are in the right position, then the worst you would have (only in the deformities) would drop signal strength.

• Portege 4000 - Installed W2K - wireless connection problem

  I installed W2K the Portege 4000. XP was too heavy a resource for this system.

  After you install the network driver wireless Cisco (3.5.13.0) of your Web site, I am unable to get a wireless connection. In XP this comes automatically with an icon. The network device switch that I also installed did not help.

  I have the following:

  Connection to the local network - ethernet

  2 - wireless LAN connection

  Although LAKE 2 is activated this still does not pick up wireless.

  Any ideas?

  Hello

  PUH Windows 2000 is an older system. I didn t forget not all parameters of WLan connection and so I googled a bit.

  and I found an interesting page and a brief description how to configure Wlan connection in W2k.

  Check this box:
  http://www.Yorktech.com/wireless/windows2000/configureW2k.htm

  Welcome them

• Wireless connection on Portege R100

  I have a couple of portege R100. When you connect to my domain, using the wireless connection, the logon scripts fail to run the first time. If you log out, then log in again, the script will run without problem. Y at - it a fix for this problem?

  Hello

  Unfortunately have no proper explanation, but I guess that WLAN cannot be connected so fast that LAN and it may be the reason why the first logon fails. In my opinion it has nothing to do with the functionality of the device and this is just a feature of network.

  Maybe some WLAN expert can give you a good explanation.

  Good luck!

• PC HP Pavilion 15 15-p001tx: control wifi wireless connectivity issues

  Hello
  Member of the Community/Forum
  
  Model name - laptop Hp Pavilion 15 (15-p001TX)
  Questions - Brodcomm 802.11n wireless adapter not Worming.
  
  Problems-
  I was faced with the same problem for 4 days and I tried all possible means to resolve out, but nothing works.
  
  Problems are the following:-

  1) Wifi stopped working 15 minutes to restart the computer and the wifi icon is automatically limited, and then it automatically become the LAN (small PC icon) and after this phone get hanged every time.
  
  to re work I need for wtich forcefully from the power button.
  
  2) I followed all the tips and tricks to solve the problem and even take a Hp support helps solve this problem of wifi. but nothing works... no one has helped me on this problem.
  
  Here are the ways I've tried.
  
  1. that tick managent of power, I have UN ticked (from PROPERTIES)
  
  2. using the CMD, I reset
  
  3. I DID cofig automatic Wlan disable (and put it on startup)
  
  4. update the drivers to the latest Version.
  
  5 install the latest drivers from the HP website brodcomm or even other Web sites.
  
  No the above to help me out.
  
  3) all wired network work great, but when I swtich to wifi, it will automatically limited and then diirectly hang the entire notebook.
  
  Please please suggest the Suggestion and the ways out sorting valueable.
  
  He's really frustrated now, I do not understand what are the ways to my wifi on working condition.
  
  Thank you
  
  Kind regards

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Aditya Rai

  Aditya Rai

  Hello @adityarai82,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I read your post about the WiFi problem and wanted to help you!  I understand that you have tried the troubleshooting steps a lot already, without success.

  Try to review these steps, offered by community member @Great-Christine-Tree:

  First of all, we have a step by step guide to guide you through the process of diagnosis here:
  Troubleshooting your wireless network and Internet access

  A second option is to try the following steps:
  Powercycle the network:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.
  
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.
  
  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.
  
  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.
  
  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.
  
  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down list in the upper right of the document.

  Source: fixes Common for wireless connectivity problems.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Wireless Chipset in Tecra M10 - 1CH

  Hello

  Please can you me the Chipset wireless full in Tecra M10 - 1CH?

  Thank you.

  You mean what WLAN card is inside or what?

• WT200 3G - manager says wireless connection is off

  Can someone please. I have a Tablet WT200 and try to use/installation of the component of the 3G...
  But the wireless connection manager continues to tell me that the radio is turned off.

  There is no switch and I've searched the net for a solution but I have seen the same question but not the answer.

  Help me! PLEASE, I BEG YOU!

  Does not WT200 Tablet contain a physical switch to turn on WLan. You must ensure that the communications function wireless (in Win 7 settings) is enabled!

  You can do this in the start menu-> Control Panel-> network and internet-> network and sharing Center
  Here, press Set new connection or a network

  At least, you should go to: start-> all programs-> Toshiba-> network & connectivity-> Wlan indicator settings
  and may display the State of the Wlan connection system

• Loss of wireless connection casual on satellite C660-115

  Hey,.

  I have a Toshiba Satellite c660 (2.5 years now, I think) and I have problems with my wireless connection (for 3 weeks now).
  Never had any problems with my connection before.

  When I use my laptop + - every hour my laptop disconnects Internet and immediately connects again.
  My computer is often used for playing games online and after 3 weeks, it's starting to annoy me, because I need to restart the whole game etc...

  Now, I have already updated all my WLAN drivers, I have the latest version of the BIOS update, and I adapted my energy profile settings to make sure that my computer is not turning off my wireless connection.

  I really think that the problem is on my computer because I have the same problem on 2 different networks.
  Don't know what to do, I hope someone can help me.

  Kind regards
  Jeroen

  Double messages or crossed messages are not allowed. You already posted in this thread: http://forums.computers.toshiba-europe.com/forums//thread.jspa?threadID=72824
  Follow * a * thread to avoid misunderstandings.