Re: Satellite C55-A-1JL - the fan spins at high speed after updating BIOS

Similar Questions

• Satellite A100 - the fan runs at high speed after idle standby

  Hello

  My laptop is Satellite A100-912.

  The problem is when I suspend it for more the a few minutes when the fan is running at high speed. This occurs on both Windows XP and Linux GNU. When the temperature of the two nuclei will more then 51 degrees C fan slows down and begins to work as expected. Suspended for a short time (about a minute or two) the fan speed is OK.

  I've updated to the latest version of the BIOS.

  Hello

  What version of BIOS you have installed? Has recently been the machine in for repair? A few interesting facts where I need some information to help you...
  By the way: is your machine still in warranty?

  Welcome them

• HP 8510W boot not until the cool, the fan runs at high speed

  I did a little research but didn't really much other than dust cleaning. I did this, even removed the fan and the heat sink.

  Operating system: 32-bit Win7

  Early days of cold, boots upwards, normally, the fan turns at slow speed. CPUID Hardware Monitor shows all the time in the range 30 c - 60 c. From a web browser will cause the fan to spped, finally at full throttle, CPUID HW Monitor says:

  TZ2_ up to 90 C

  TZ5_ up to 100 C

  Remote1 up to 90 C

  Other times remain in the range of 30 c - 60 c

  The task manager's performance tab shows 1%-3% CPU, 30-40% consumption of Mem.

  Close all does not help, time remain high and the fan continues to run at high speed. Reset does not succeed, it will cut down, try to restart and stop again. Finally, it will sometimes get a screen where Windows thinks it could not start and wants to fix/reinstall the files, or go back to a restore point. If to cool for 10 to 15 minutes, it will start normally with the low fan speed until something starts to run (CPUID HW Monitor and Task Manager do not cause the fan speed).

  So nobody knows what TZ2_, the TZ5_ and the Remote1 map 30 5 8510W mother? Is this a real plus temp likely situation, ot possibly a problem with bios/driver not reading sensor properly?

  Well well, so far, no response, but I seem to have solved the problem. I tried reverting heatsink composed of all chips connected to the conduct of heat with no improvement. By checking things right after a stop, I noticed that the graphics chip was too hot to the touch even with the new complex. This meant that it was not the heat pipe.

  Ordered a used one from eBay, put it in and now it's stay nice and cool, not more than 60 C.

  The part number for the heat pipe is 452227-001.

• The fans are not stop working after upgrading BIOS on Satellite A200

  Hello

  IM using the Satellite A200-1bp. I recently updated my BIOS 5.20 - winner and my fans are not end all the time working.
  I think his reason is update BIOS
  I'm looking for the BIOS below.

  Please help me...

  Hello

  Maybe this thread can help http://forums.computers.toshiba-europe.com/forums//thread.jspa?messageID=128543

  Make sure that you use the right BIOS for your laptop model.

• Re: Satellite P750: the fan rotates at high speed without load

  Hello
  I am a developer of software for the Germany and often uncomfortable in my quiet office. Well, since I got my new P750 I am facing a strange problem: while the CPU load remains very low, fan works suddenly 71% while the cpu temperature is 44% in health monitor. If I unplug the cable that the fan immediately gets quiet at 0%.

  for normal use with connected to the fan cable * always * works 64%, while having temperatures of 40%.

  I checked the settings in the power manager for the parameters of cooling system. If it is set for maximum performance on the cable and balanced on the battery, it seems completely unnecessary to let the fan run all the time, so only ist very low temperature.

  Hello

  As you probably know cooling fans are controlled by sensors on the motherboard and laptop users don t have much influence on the activity of the fan.

  In my opinion for your work you need high performance t n so I recommend you to use the power plan balanced all the time. In the balanced power plan change advanced power options > cooling method optimized battery and it should reduce the activity of fan.

  It is the same on my Satellite P500 and the laptop runs pretty quiet. Also, make sure that the laptop is placed on the desktop and noting may block the ventilation openings.

• Satellite Pro P100 GPU Fan off or full speed after updating the Bios to 4.20

  Hello

  After installing the "nine" update Bios 4.20 the GPU fan is when the laptop is cool. While working with him the GPU temperature increases up to 100 ° C (very hot), then the fan starts to run at medium speed and the GPU is cooled. After a restart, for example. the next day, the fan still works on the average speed or high (very noisy). With the bios version before this problem appeared.

  Someone at - it the same problem with his laptop?
  Someone there done the update of the Bios before 4.20 and can send it to me?

  Welcome them
  Rommulaner

  Hi guys

  May I ask which graphics drivers are you using?
  If you n t use the original graphic driver on the site of Toshiba and the laptop can starts overheating. Non - Toshiba GPU led don t support protection against overheating as the drivers of Toshiba! If the temperature of the GPU would rise to a higher level, then the pilot would diminish GPU performance to reduce the heat.
  Drivers graphic non-Toshiba don t control it and therefore the GPU could produce more heat.

  Another reason for this problem could be changed to value of table fan.
  I think that the cooling modules run faster and more often because the table fan has been changed in the BIOS. It may be necessary to prevent the overheating of the material.

  Concerning

• Satellite A500: problem with the driver of sound and display after update!

  A500 Windows 7-64 bit

  I download the latest driver (6.0.1.6048) sound and display driver (8.16.11.8973) and I have a few problems.
  The colors are too bright and the sound is too deep (as the middle are too low).

  Hello

  Then why you n t go back to earlier versions of the driver?
  In your case, I would recommend setting the operating system at the point of time at first, until you have updated the drivers.
  Usually, this should help to recover the old drivers again.

  Welcome them

• New z500 - fan runs at high speed on startup

  Hello

  I just bought a new Ideapad, a MBYP9GE Z500, that I got no windows, when I turn on the laptop it works in the BIOS. The problem I have is that the fan starts in high speed immediately and it is very noisy at start up. Is this normal? I want to say how is possible that the fan is noisy so if I am not under what whether intensive? Maybe it's because I have not installed yet any system? Or is it my laptop malfunction?

  Thanks in advance!

  Hi neokenchi,

  Thank you for your response. Yesterday, I installed Windows 7 and the appropriate drivers, that solved the problem. The fan runs at high speed before installing a system was apparently the default heat setting, as you suggested.

  Thanks again!

• Satellite A210-171 - clean the fan/radiator

  I have a satellite A210-171. The fan runs strong at times, more heating and twice a day of closure, I guess I have to give it a good clean? It's anywhere, I looked I can't find instructions on how to clean my particular * do * and * model *.

  I know that I can use an air can without starting to dismantle things, but I think he needs a little more to get my laptop to work like new. Any help telling me where to look would be greatly appreciated, I hope as well as some pictures of cell being dismantled (eyes rolling)

  Thank you

  Hey Gradma Sue,

  Why you didn t use the forum search? You will find a sufficient number of threads on the cleaning of a Toshiba laptop.

  You only need compressed air spray. With this, you can blow the dust from the cooling fans and it of quite easy to use.
  I've created an interesting article from Toshiba that describes this step by step:
  http://APS2.toshiba-tro.de/KB0/HTD7A01ZZ000AR01.htm

• Portege R500 - the fan runs at full speed during the recovery from sleep mode

  Hello

  The fan in my R500 works at full speed when he was in the system sleep.
  The only thing that helps is a reboot. :-/

  Is there a solution to this problem?

  Hello Allan

  I really wonder that you define this as a problem. From my point of view the problem is something else. You have a problem when you cannot boot up your laptop. You have a problem if you are unable to use certain features or if you can not open the DVD player. It is a problem.

  Back to your problem: have you tried to change the power settings, to change the method of cooling in the Toshiba power settings? Play a little with it. I optimized the use of my wholesale Satellite P200 and the fan operates at low speed. OK it is not the best example to compare the two models of laptops, but try it.

• Fans always operate at high speed after power failure

  HP Pavilion Slimline S5780T - Windows 7 Home Premium 64-bit

  After a power failure a night or more recent, our Pavilion Slimline case fan and CPU fan have both run at high speed all the time, starting from the system. The level of noise is intolerable.

  I opened and cleaned all the dust from the inside of the case, including the removal of the heatsink from the CPU. Everything is clean.

  I ran the following HP Vision diagnostic, test the system, including fans. During the test of fan, the fans ran at 100%, then fell to the former level normal, quiet, then ramp back up to 100%. So says HP fans diagnostic tests are OK when there is always a problem. And it is possible for them to run at slow, normal speed.

  I installed the free SpeedFan utility, but there is not place to adjust the fan speed manually.

  How can I find the problem and the fans run at normal speed, as they did before the power failure? Everything that controls the speed of the CPU fan and the fan is broken.

  Thank you and best regards,

  Stephen - Myrtle Beach, SC

  Strange things happen when power flucuations or failures occur.  Most probably the motherboard has been damaged by the PPE and that is normally not as repairable by a DIY.  If you could find a newer BIOS, that to solve the problem.  Since there can be no more recent BIOS, try to remove the battery from the motherboard for the night and then put the file in and reset the BIOS to see if that helps the default value.  Otherwise, it might be repairable.

• Touchpad no longer works after update BIOS on Satellite A500-1GL

  Hello world

  I just bought my laptop Satellite A500-1GL today. I started at the top and plays a bit (nothing serious). The touchpad worked very well at the moment.

  Then I discovered this tool to update the material and the update of the BIOS that worked without any problems. After I restarted the laptop, BIOS, loaded the default values of the installation and recorded.
  After that Windows 7 (x 64) started the touchpad no longer works...

  I downloaded the driver here and installed again once, still does not. I went into the BIOS, disabled the touchpad (I thought that maybe it's a bug...) and started again. It still does not...

  I enabled it again in the BIOS, tried to push the function + F9, but it still does not... Finally, I used the recovery and installed a Windows 7 costs.
  But unfortunately it still doesn't.

  Now, I'm out of ideas, can anyone help?
  Is there a chance to get the older version of BIOS to downgrade it?

  Thanks in advance ;)

  Hello

  It seems strange that after update Bios touchpad no longer works.

  > Is there a chance to get the older version of BIOS to downgrade it?

  To be honest, I don't know where to find. In any case, do a search on Google. Perhaps, other users of the forum can give you a link to download.
  The downgrade of the Bios is riskier upgrade procedure. So, be careful the next time...
  Advice for the future; Do not touch the running system.

  Good luck!

• zbook u15: fan at high speed after installed windows 10

  Yesterday, I updated to windows 7 pro for windows 10 pro.  I have rarely heard my fan in windows 7 and only when I was cad or had a large number of open images.  With 10 windows, my fan is at high speed all the time.

  Suggestions?

  Ok

  Found two programs running that caused the fan to high speed.

  One was post 2012 31% of the processor chips

  other was

  AlertusDesktop or 32% of the processor.

  E-mail private, removed the Alertusdesktop for now and normal operation.

  Thank you!

• I have 4 GB of RAM, but when my i play any game, my CPU fan runs at high speed and my system gets shut down within minutes.

  I have 4 GB of RAM, but when my i play any game for example NFS most wanted, my CPU fan runs at high speed and my system gets shut down within minutes. Help me solve this problem

  If you overclocked?  If so, cancel that.  If the games you play are poorly written, it is not that you can do about it.  If you have not cleaned the dust and lint from your computer within a certain time, you should do that because it accumulates and causes overheating.  For desktop computers, remove the cover and carefully use compressed gas to blow off the dust, especially around the fins in the processor heat sink and air ducts.  For a laptop, I'll ring gas compressed through the ventilation openings.

  Good luck.

• Cannot use the recovery CD after update BIOS on Tecra 9000.

  Failed to retrieve the system (Windows 2000) after update BIOS on Tecra 9000. Recovery CD says "it's a bad machine. Can I go back to old BIOS? Another solution?

  Hello

  Maybe chain can confirm, but I put t he seems the best idea to mix stuff designed for laptops Americans and Europeans models.

  Can you please confirm if the method described in the previous ad works?