(Redirected) Drive hard failure error

Similar Questions

• New drive HARD & OS errors-> HP 8000 Elite Small Form Factor PC

  New drive HARD & OS errors---> HP 8000 Elite Small Form Factor PC
  
  Can not install Win XP on another hard drive
  
  I work with a...
  HP Compaq 8000 Elite Small Form Factor PC
  
  Original SATA HDD is loaded with Windows 7 Pro.
  
  In order to install a program using this PC as a digital video recorder
  I installed the video capture PCI card and related software. I had problems
  associated with software and Windows 7.
  
  I know that the software works with Windows XP.
  Do not want to remove the original HDD, I tried my win7
  to replace the HARD drive and do a clean install of XP.
  
  I get the same error during the installation of the OS.  I tried different
  SATA and different XP install disks.
  
  The error I get is shown in this photo.

  

  Original HP HARD drive is a Hitachi 160 GB
  
  I tried 2 known to be good SATA drives.
  Seagate 500GB
  WD 80 GB
  
  I checked the bios settings and even revenue tio rear BIOS
  default settings.

  I get this error even with everything I tried to do.

  This happens during the OS install just after or during the process of the installation of temporary files are current

  written to the HD.
  
  When I re - install the original HD loaded with Win7, everything works as it
  expected.
  
  Any ideas on what] s going on here?

  Hello:

  The problem is that you must incorporate the necessary sata ahci drivers for windows XP to see the hard drive.

  Has Windows 7 and XP is too old an operating system to make them.

  Read the info at the link below, section of Intel and then read the downloadable PDF document for instructions on how to integrate all the drivers.

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/m-p/114120#M17758

  The only other way to install XP on this model is to go into the bios, the storage section and change the setting of sata ahci to ide emulation, save the setting here and once again, when you go out.

  The problem is that if you do this, you cannot change the setting for the preferred setting of DCIS, unless you know how to install the correct ahci sata driver after installing XP from the controller.  If you try to just change the setting back on ahci without having to install the controller driver, the PC does not start upward.

  Try "slipstreaming" the drivers first and if you can't swing, install XP in IDE mode and I'll help you get the drivers installed, so you can change the BIOS to ahci setting.

• drive hard failure may be imminent.

  When I turn on my studio 1555, it displays a warning of intelligent prediction to drive hard failure! When starting, it is slower than before, and I do serious work with my laptop, it gives me a blue screen on cenrel sth and stop! and from time to time windows alerts me to back up my data! I already ran a dell diagnostics and attached the picture! PLEASE, I BEG YOU! Somone help me. 

  No, there is no way to fix the drive - it must be replaced.

• Drive hard failure - where to find recovery discs

  I have a HP G60 - 235WM system that comes with having a hard drive failure.

  Before the breakup, I tried to create a defined recovery disk but the process

  cancelled itself in the middle of the creation of the file. Since then, I've run a system recovery that seemed to work until the second day when on startup, I got the drive imminent failure Prompt and selecting Blons is no not a thing... I bought a new drive, but need to access a set of recovery discs...

  Then I bought another laptop with WIN 8.1 - questions

  Can I create a set with the 8.1 recovery disk WIN that will allow me to recover the original software Vista system?

  or where can I get a Vista system recovery disk?

  Note: the failed hard drive can be accessed via the USB port but does not start...

  Hello:

  You can call HP and see if they have a set of Vista recovery disks for your model.

  If this isn't the case, you can get them from this provider on the link below.

  http://www.computersurgeons.com/ProductDetails.aspx?ID=13223

  You will not be able to use a set of recovery disks you create on a different model PC.

• Drive hard failure. Code 7?

  Tech, tried to change the drive letter of the hard drive to I-C, locked to computer. Won't go into office.  Tries to start, but the habit.  Drive hard diagnosis on the home screen displays disk hard failure, Code 7.  What should I do?

  Try restarting, press F8 repeatedly to get in safe mode and in safe mode, select "last good configuration"(the most recent setting that worked)"known. . Reboot and see if that gets you on the desktop.

  How to change or assign a drive letter in Windows XP.

  http://support.Microsoft.com/kb/307844

  Let us know if this solves the problem.

• Is this another drive hard failure? (2 times in slot a few months)

  Hello, I decided to post here before contacting HP about this problem again. As stated in the subject, it is the second time I had problems with my hard drive Compaq Presario CQ56. The first time a month or so earlier, he failed completely, I had to pay about $ 30 to $ 40 just to have the box sent us in a week to send the laptop in for repair. About 1 week later, I got the laptop back, and of course, I started to download lost my programs, antivirus, etc.. It worked perfectly until about an hour before, where even once, it cannot detect the hard drive. When I start the computer, he rarely shows the red screen with compaq Q, then it stays on a black screen for about 1 to 2 minutes, which then results in the Windows Boot Manager comes up saying the following:

  Hello

  From what you describe, it is certainly a hard failure so you definitely need to contact HP.  Personally, considering that it is the 2nd HARD disk in less than 2 months, I say it's a bad luck (however unlikely) or there is another issue at stake - it may be useful to suggest this to HP when you contact them.

  Kind regards

  DP - K

• HP Pavilion DV6-3041TX drive HARD failure and possible design Intel series 6 Chipset problem

  Hey guys

  I saw corruption serious hdd on my system for some time now and was just move to replace the drive hard when I came across the problem of design of Intel® chipsets. Now, I think that my system is the range of serial number for this question and as the current drive does not start, I can't check the Device Manager to see if the chipset is one of those affected.

  Is there anyway for me to check this from a USB bootable or something similar, because I don't want to have to go through the effort to replace the hard drive and reinstall windows just to find the chipset is wrong?

  Thank you

  (Now, this is my first post on the forum if I appoilgise if I've got this in the wrong place)

  Open the door of the memory on the bottom of the laptop and look under the memory for a number of motherboard.

  You should have the Intel HM55 chipset, but we can be sure that if we know the motherboard part number.

  You should have one of these two tips:

  630281 001
  615281 001

• drive hard failure after 2 years of use, is this normal for a 1.6-inch toshiba 80 GB drive

  is the lifetime of a drive hard toshiba mini car shorts... and how to get data back now that the player is without a normal connection only a flat cable...

  In fact, that would be my next suggestion. If you're technical enough, you can use a Linux, or in your case, USB key bootable CD. I have had several instances where do this on a disk failed HARD still allows me to remove some data. Not everything, but it's worth a shot-to-shot, sure! And even if it doesn't work, you still have the USB key to use.

• HP beats 15 laptop: computer drive HARD failure diagnosis

  Hi people,

  I'm a little angry, I hope one of you lovely people can help me with some advice. My wife tried using the contact HP online support face today, but did not get a useful answer. The laptop in question has still 2 months warranty on this subject and I would like this issue to be fixed before the expiration of the warranty.

  The problem:

  A month or two ago my wife said that the laptop occasionally runs slowly or freezes at random times, then started working again without problem. I'm on the laptop, run scans antivirus, temporary files clear and others with CCleaner, uninstall unnecessary programs and then turn off most of the autobooting services and programs with msconfig. Nothing really came from him, but he did and apparently not having problems while I used it.

  A week later, more complaints that the laptop was running slower than optimal, with another request to examine it. This time he did freeze while I use it, so I run ladies sfc diagnostics and memory, which came to own. Then it was time to try to run through the optimization of windows to speed it up a little.

  Has held a few weeks for me since then, always heard there are problems, but not having is not the opportunity to study.

  Last night I finally get around to running the diagnostics of HP at the start and check out the source (I hope!) of the problem. Hard disk check is coming up with an error indicating that the disk is not healthy, technical Department should be contacted directly. I saved the newspapers to a USB port, I'll post the results in the next post.

  The solution:

  Could I please have some advice on the best way to proceed on this matter now? I'd appreciate any help.

  Kind regards

  Jason

  2015-12-03 22:07:55 =.
  2015-12-03 22:07:55 5.9.0.0 EFI diagnostic system has started
  2015-12-03 22:07:55 load white Options
  2015-12-03 22:07:55 acquired SysDiagsBiosData2011 Configuration variable
  2015-12-03 22:07:55 HP thermal diagnosis Protocol not available
  2015-12-03 22:07:55 ID system: 22A 8
  2015-12-03 22:07:55 BIOS HP Image Interface Protocol Version 2.0
  2015-12-03 22:07:55 found 4 4 active processors, Max 4 processors
  2015-12-03 22:07:55 found 1 absolute pointer or protocols
  2015-12-03 22:07:55 0 found UART peripheral path node.
  2015-12-03 22:07:55 found touchscreen device
  2015-12-03 22:07:55 system family: = 2
  2015-12-03 22:07:55 PlatformLang reported as en-US.
  2015-12-03 22:07:55 selected language is currently (eng).
  2015-12-03 22:08:07 Player library initialization.
  2015-12-03 22:08:07 TscPerSecond = 065238C98h
  2015-12-03 22:08:07 installed protocol commands ATA DTDS
  2015-12-03 22:08:07 Found installed DTD ATA commands protocol supporting Packet orders!
  2015-12-03 22:08:07 found 1 hard drive.
  2015-12-03 22:08:07 drive CHIP 0 supported
  2015-12-03 22:08:07 AtaCommandsBindBlockIoProtocol(): link block of e/s Protocol (0x9B137298) to drive 0
  2015-12-03 22:08:07 found 1 optical disc.
  2015-12-03 22:08:07 AtaCommandsBindBlockIoProtocol(): link block of e/s Protocol (0x9B108C18) to drive 1
  2015-12-03 22:08:07 ATA Total 2 records found
  2015-12-03 22:08:07 no handle found support EFI_EXT_SCSI_PASS_THRU_PROTOCOL (143B7632-B81B-4CB7-ABD3-B625A5B9BFFE).
  2015-12-03 22:08:07 no handle found support EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL_GUID (EC51EF5C-2CF3-4A55-BF85-B63CA3B13F44).
  2015-12-03 22:08:07 no handle found support LEGACY_NVM_EXPRESS_PASS_THRU_PROTOCOL_GUID (EC51EF5C-2CF3-4A55-BF85-B63CA3B13F44).
  2015-12-03 22:08:07 1 hard drive Total records found
  2015-12-03 22:08:07 1 total optical disk drives found
  2015-12-03 22:08:07 found 1 hard drives
  2015-12-03 22:08:07 found 1 optical discs
  2015-12-03 22:08:07 ID system: 22A 8
  2015-12-03 22:08:07 system model: = HP Beats 15 Notebook PC
  2015-12-03 22:08:07 system SKU: = K1S17EA #ABU
  2015-12-03 22:08:07 ID system: 22A 8
  2015-12-03 22:08:07 11 Type operating system image:
  2015-12-03 22:08:07 HARD drive 0 model: HGST HTS541010A9E680
  2015-12-03 22:08:07 0 Serial HARD drive: JA100A1F3B5JNM
  2015-12-03 22:08:07 0 ODD model: hp DVD - RW GUB0N
  2015-12-03 22:08:07 STRANGE series 0: M7FEB420920
  2015-12-03 22:08:07 DIMM 0 serial number: 000013A 4
  2015-12-03 22:08:07 DIMM 0 Part Number: AM1L16BC8R2-B1QS
  2015-12-03 22:08:07 BIOS revision: F.43
  2015-12-03 22:08:07 platform Vendor ID: 0 x 1022
  2015-12-03 22:08:07 Platform Device ID: 0 x 1400
  2015-12-03 22:08:07 only a single MEMORY bar (Index 1) is filled on the system
  2015-12-03 22:08:07 found EFI_HP_DIMM_ID_PROTOCOL
  2015-12-03 22:08:07 InitializeCeeLogs - no record found
  2015-12-03 22:08:07 BattInit: Protocol 2010.
  2015-12-03 22:08:07 start graphics system Menu diagnosis
  2015-12-03 22:08:37 quick test of the chosen system
  2015-12-03 22:08:37 calculation time to Test memory
  2015-12-03 22:08:37 total 7399 MB of memory, Free 7285 MB (1865128 Pages)
  2015-12-03 22:08:37 parm buffer allocation
  2015-12-03 22:08:37 case of test Init
  2015-12-03 22:08:37 calculated 0x000000001B9FDAC6 TSC ticks per MB
  2015-12-03 22:08:37 estimated duration total = 2181 s
  2015-12-03 22:08:37 battery test started
  2015-12-03 22:08:37 SmartAdapter: Protocol not available.
  2015-12-03 22:08:37 number of batteries 1
  2015-12-03 22:08:38 BattResetCharger: No.0 (success).
  2015-12-03 22:08:38 BattResetCharger: n ° 1 (success).
  2015-12-03 22:08:41 battery 0 returned 0 x 0000000000000001
  2015-12-03 22:08:42 battery result = 1
  2015-12-03 22:08:42 CPU test started
  2015-12-03 22:08:42 UDM Cpu start test.
  2015-12-03 22:08:42 features BIOS 0x003000093F899880
  2015-12-03 22:08:42 ID system: 22A 8
  2015-12-03 22:08:42 ===========================================================
  2015-12-03 22:08:42 starting CpuDiags.udm version 1.03 built 14 September 2015 10:24:13
  2015-12-03 22:08:42 CpuDiags.UDM full init
  2015-12-03 22:08:49 test complete CPU - result 1
  2015-12-03 22:08:49 Wireless Module check started
  2015-12-03 22:08:49 Wireless Module audit completed - results 1
  2015-12-03 22:08:49 test Board full system - result 1
  2015-12-03 22:08:49 SMART Check started
  2015-12-03 22:08:49 SMART audit end - result 1
  2015-12-03 22:08:49 short DST has begun
  2015-12-03 22:08:53 memory quick check started
  2015-12-03 22:09:02 hard drive DST Code 0: 7
  2015-12-03 22:09:03 hard Drive 0 DST Description: the previous self-test completed having the read element of the test failed
  2015-12-03 22:09:03 tested 20 MB in 10000 ms with 4 processors, the duration of the standardized test is 2000 ms/MB
  2015-12-03 22:09:03 test memory used 5241 Pages
  2015-12-03 22:09:03 check fast memory completed - results 2
  2015-12-03 22:09:03 code DST hard drive 0: 7
  2015-12-03 22:09:03 hard Drive 0 DST Description: the previous self-test completed having the read element of the test failed
  2015-12-03 22:09:03 short completed DST - score 3
  2015-12-03 22:09:03 error code = 0 x 303
  2015-12-03 22:09:03 serial number: 5CD4493T5J
  2015-12-03 22:09:03 guaranteed Start Date: 25/02/2015
  2015-12-03 22:09:03 WarrantyIDString size = 60
  2015-12-03 22:09:03 guaranteed ID = UBV6LF-7HQ7SB-MFPV6K - 60 X 103
  2015-12-03 22:09:03 short completed DST - score 3
  2015-12-03 22:09:03 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:09:03 0 0 17 0
  2015-12-03 22:09:03 0 0 20 1
  2015-12-03 22:09:03 paired FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:09:43 quick test of the complete system
  2015-12-03 22:09:46 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:09:46 0 0 17 0
  2015-12-03 22:09:46 0 0 20 1
  2015-12-03 22:09:46 paired FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:09:51 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:09:51 0 0 17 0
  2015-12-03 22:09:51 0 0 20 1
  2015-12-03 22:09:51 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:09:58 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:09:58 0 0 17 0
  2015-12-03 22:09:58 0 0 20 1
  2015-12-03 22:09:58 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:10:11 way to unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:10:11 0 0 17 0
  2015-12-03 22:10:11 0 0 20 1
  2015-12-03 22:10:11 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:10:22 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:10:22 0 0 17 0
  2015-12-03 22:10:22 0 0 20 1
  2015-12-03 22:10:22 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:10:31 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:10:31 0 0 17 0
  2015-12-03 22:10:31 0 0 20 1
  2015-12-03 22:10:31 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:10:36 Road Management of BIOS HP EFI
  2015-12-03 22:10:42 uninstall DTD ATA commands of Protocol
  2015-12-03 22:10:42 out of System Diagnostics
  2015-12-03 22:19:19 =.
  2015-12-03 22:19:19 5.9.0.0 EFI diagnostic system has started
  2015-12-03 22:19:19 load white Options
  2015-12-03 22:19:19 acquired SysDiagsBiosData2011 Configuration variable
  2015-12-03 22:19:19 HP thermal Diagnostic Protocol is not available
  2015-12-03 22:19:19 system ID: 22A 8
  2015-12-03 22:19:19 BIOS HP Image Interface Protocol Version 2.0
  2015-12-03 22:19:19 found 4 4 active processors, Max 4 processors
  2015-12-03 22:19:19 found 1 absolute pointer or protocols
  2015-12-03 22:19:19 0 found UART peripheral path node.
  2015-12-03 22:19:19 found touchscreen device
  2015-12-03 22:19:19 system family: = 2
  2015-12-03 22:19:19 selected language is currently (eng).
  2015-12-03 22:19:21 Player library initialization.
  2015-12-03 22:19:21 TscPerSecond = 065239E32h
  2015-12-03 22:19:21 installed protocol commands ATA DTDS
  2015-12-03 22:19:21 found installed DTD ATA commands protocol supporting Packet orders!
  2015-12-03 22:19:21 found 1 hard drive.
  2015-12-03 22:19:21 drive CHIP 0 supported
  2015-12-03 22:19:21 AtaCommandsBindBlockIoProtocol(): link block of e/s Protocol (0x9B137298) to drive 0
  2015-12-03 22:19:21 found 1 optical disc.
  2015-12-03 22:19:21 AtaCommandsBindBlockIoProtocol(): link block of e/s Protocol (0x9B108C18) to drive 1
  2015-12-03 22:19:21 2 ATA Total records found
  2015-12-03 22:19:21 no handle found support EFI_EXT_SCSI_PASS_THRU_PROTOCOL (143B7632-B81B-4CB7-ABD3-B625A5B9BFFE).
  2015-12-03 22:19:21 no handle found support EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL_GUID (EC51EF5C-2CF3-4A55-BF85-B63CA3B13F44).
  2015-12-03 22:19:21 no handle found support LEGACY_NVM_EXPRESS_PASS_THRU_PROTOCOL_GUID (EC51EF5C-2CF3-4A55-BF85-B63CA3B13F44).
  2015-12-03 22:19:21 1 hard drive Total records found
  2015-12-03 22:19:21 1 total optical disk drives found
  2015-12-03 22:19:21 found 1 hard drives
  2015-12-03 22:19:21 found 1 optical discs
  2015-12-03 22:19:21 ID system: 22A 8
  2015-12-03 22:19:21 system model: = HP Beats 15 Notebook PC
  2015-12-03 22:19:21 system SKU: = K1S17EA #ABU
  2015-12-03 22:19:21 ID system: 22A 8
  2015-12-03 22:19:21 11 Type operating system image:
  2015-12-03 22:19:21 0 model HDD: HGST HTS541010A9E680
  2015-12-03 22:19:21 0 Serial HDD: JA100A1F3B5JNM
  2015-12-03 22:19:21 ODD 0 model: hp DVD - RW GUB0N
  2015-12-03 22:19:21 STRANGE series 0: M7FEB420920
  2015-12-03 22:19:21 DIMM 0 serial number: 000013A 4
  2015-12-03 22:19:21 DIMM 0 Part Number: AM1L16BC8R2-B1QS
  2015-12-03 22:19:21 BIOS revision: F.43
  2015-12-03 22:19:21 platform Vendor ID: 0 x 1022
  2015-12-03 22:19:21 Platform Device ID: 0 x 1400
  2015-12-03 22:19:21 only a single MEMORY bar (Index 1) is filled on the system
  2015-12-03 22:19:21 found EFI_HP_DIMM_ID_PROTOCOL
  2015-12-03 22:19:21 BattInit: Protocol 2010.
  2015-12-03 22:19:21 from Menu of Diagnostic graphics system
  2015-12-03 22:19:26 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:19:26 0 0 17 0
  2015-12-03 22:19:26 0 0 20 1
  2015-12-03 22:19:26 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:19:32 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:19:32 0 0 17 0
  2015-12-03 22:19:32 0 0 20 1
  2015-12-03 22:19:32 set match FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:19:34 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:19:34 0 0 17 0
  2015-12-03 22:19:34 0 0 20 1
  2015-12-03 22:19:34 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:20:14 way to unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:20:14 0 0 17 0
  2015-12-03 22:20:14 0 0 20 1
  2015-12-03 22:20:14 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:20:20 uninstall DTD ATA commands of Protocol
  2015-12-03 22:20:20 out of System Diagnostics
  2015-12-03 22:24:13 =.
  2015-12-03 22:24:13 5.9.0.0 EFI diagnostic system has started
  2015-12-03 22:24:13 load white Options
  2015-12-03 22:24:13 acquired SysDiagsBiosData2011 Configuration variable
  2015-12-03 22:24:13 HP thermal diagnosis Protocol not available
  2015-12-03 22:24:13 system ID: 22A 8
  2015-12-03 22:24:13 BIOS HP Image Interface Protocol Version 2.0
  2015-12-03 22:24:13 found 4 4 active processors, Max 4 processors
  2015-12-03 22:24:13 found 1 absolute pointer or protocols
  2015-12-03 22:24:14 0 found UART peripheral path node.
  2015-12-03 22:24:14 found touchscreen device
  2015-12-03 22:24:14 system family: = 2
  2015-12-03 22:24:14 selected language is currently (eng).
  2015-12-03 22:24:16 Player library initialization.
  2015-12-03 22:24:16 TscPerSecond = 065239F87h
  2015-12-03 22:24:16 installed protocol commands ATA DTDS
  2015-12-03 22:24:16 found installed DTD ATA commands protocol supporting Packet orders!
  2015-12-03 22:24:16 found 1 hard drive.
  2015-12-03 22:24:16 drive CHIP 0 supported
  2015-12-03 22:24:16 AtaCommandsBindBlockIoProtocol(): link block of e/s Protocol (0x9B137298) to drive 0
  2015-12-03 22:24:16 found 1 optical disc.
  2015-12-03 22:24:16 AtaCommandsBindBlockIoProtocol(): link block of e/s Protocol (0x9B108C18) to drive 1
  2015-12-03 22:24:16 ATA Total 2 records found
  2015-12-03 22:24:16 no handle found support EFI_EXT_SCSI_PASS_THRU_PROTOCOL (143B7632-B81B-4CB7-ABD3-B625A5B9BFFE).
  2015-12-03 22:24:16 no handle found support EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL_GUID (EC51EF5C-2CF3-4A55-BF85-B63CA3B13F44).
  2015-12-03 22:24:16 no handle found support LEGACY_NVM_EXPRESS_PASS_THRU_PROTOCOL_GUID (EC51EF5C-2CF3-4A55-BF85-B63CA3B13F44).
  2015-12-03 22:24:16 1 hard drive Total records found
  2015-12-03 22:24:16 1 total optical disk drives found
  2015-12-03 22:24:16 found 1 hard drives
  2015-12-03 22:24:16 found 1 optical discs
  2015-12-03 22:24:16 ID system: 22A 8
  2015-12-03 22:24:16 system model: = HP Beats 15 Notebook PC
  2015-12-03 22:24:16 system SKU: = K1S17EA #ABU
  2015-12-03 22:24:16 ID system: 22A 8
  2015-12-03 22:24:16 11 Type operating system image:
  2015-12-03 22:24:16 0 model HDD: HGST HTS541010A9E680
  2015-12-03 22:24:16 HDD 0 Serial: JA100A1F3B5JNM
  2015-12-03 22:24:16 ODD 0 model: hp DVD - RW GUB0N
  2015-12-03 22:24:16 series 0 ODD: M7FEB420920
  2015-12-03 22:24:16 DIMM 0 serial number: 000013A 4
  2015-12-03 22:24:16 DIMM 0 Part Number: AM1L16BC8R2-B1QS
  2015-12-03 22:24:16 BIOS revision: F.43
  2015-12-03 22:24:16 platform Vendor ID: 0 x 1022
  2015-12-03 22:24:16 platform Device ID: 0 x 1400
  2015-12-03 22:24:16 only a single MEMORY bar (Index 1) is filled on the system
  2015-12-03 22:24:16 found EFI_HP_DIMM_ID_PROTOCOL
  2015-12-03 22:24:16 BattInit: Protocol 2010.
  2015-12-03 22:24:16 from Menu of Diagnostic graphics system
  2015-12-03 22:24:19 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:24:19 0 0 17 0
  2015-12-03 22:24:19 0 0 20 1
  2015-12-03 22:24:19 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0
  2015-12-03 22:24:42 path of unity: PciRoot(0x0) /Pci(0x11,0x0) /Sata (0 x 0, 0xFFFF, 0x0)
  2015-12-03 22:24:43 0 0 17 0
  2015-12-03 22:24:43 0 0 20 1
  2015-12-03 22:24:43 matched FailingBus = 0, FailingDev = 17, FailingFunc = 0

  Hi Jason,

  The hard drive is indeed a failure and needs to be replaced - just contact HP and make arrangements for this under warranty.

  The section of the report you cite is UBV6LF-7HQ7SB-MFPV6K-60 X 103 because this will confirm the diagnostic failure with software HPs.

  If you live in the United Kingdom, contact HP here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• Drive hard failure ID: 936JJ3-54W75L-XD003G-60VX03

  My system: HP Pavilion dv6-3040us; Product ID: WQ676UA #ABA; System ID: 143F; BIOS: F.29 25/02/2013

  Hard Drive failure ID: 936JJ3-54W75L-XD003G-60VX03 during the short test HDD.

  I was not able to find an explanation for the fault code referenced hard drive I get who runs the HARD drive test.  This code is blown on several occasions during the short test HDD and it does not in the long run test but stops with this error.  So, I guess that the drive should be replaced because a CHKDSK command-line with the set of "fix" has not solved the problem.

  My question is if I can replace the HHD with a 500 GB SSD on this motherboard?  If Yes, what steps do I take to replace the disk and recover my system and information?  I looked through the pages of BIOS and does not see a place to set the HARD drive configuration, so I wonder if the system will accept a SSD drive.  Thank you for your help.

  Yes it's a wide 7 or 9.5 mm thickness of 2.5 inches SSD is a plug-in replacement for the standard hard drive. The motherboard only supports SATA-II speed drives but SSD SATA-III will be backward compatible. The settings of the BIOS already fully support an SSD and Windows 7 and 8 run automatically TRIM to optimize the transfer of data to the SSD. It is really very simple, but you still see a lot of advice floating around days earlier, when he was more difficult. Don't overthink is my best advice. I suggest an Evo to Samsung 840:

  http://www.Newegg.com/product/product.aspx?item=N82E16820147248

  YouTube video for the replacement of the hard disk:

  http://www.YouTube.com/watch?v=QQx7PlIXFuE

  Not quite precisely your model but close enough to be useful.

  You did the recovery HP DVD when the laptop was new? With a failure on the short trial, it is not likely that the drive can be cloned to the SSD DH, but with a usb to SATA Adapter, you can recover some data.

  We can connect you to a .iso (disk image) of Windows 7 to your laptop and you can use the drivers from this site. If you can get the C:\swsetup file on the old disk, it has all the drivers and original programs.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Drive hard failure ID: 6AJBKW-0006HF-XD6U3G-6OUR03

  HP Pavilion DM4 - 1063cl

  Windows 7 Home Edition

  At the start, went to repair disk and continuously ran after 16 hours that I stopped it

  F2 run System Diagnostics: hard drive Test: and got the error message in the subject line.

  Called HP support and my computer is 3 months warranty and the person on the line could not interpret the failure code.  It is a HP code in interest.  $200 dollars to send it, when I may need just a new hard drive.  Hoping someone can help.  Thank you

  The recovery on the other machine disks should work fine as long as it is the same model. And, Yes, Windows backup & restore should be able to restore your files. If I remember correctly, some have reported having to use Windows backup at least once on a new installation prior to the restore function starts to operate. Wouldn't be a significant backup, just backup folder music or something with very little in it. May not even need that step, but if you have a problem with the backup of information no backups were done to try it.

• Satellite A660 - will not start initialize drive HARD failure

  Hello
  first of all thank you for your time.

  Model: Satellite A660 (PSAW3A-07U00R)

  The problem started yesterday, the computer has been going slowly as a closed application, so I held the off button until the pc is turned off. When I restarded the laptop, it went to a screen saying: start windows normally or repair Windows (recommended)

  When started normally it hangs just a blank screen, repair Windows recommends a system restore to a previous point that did not work. As it crashes again. I tried pressing F8 and boot in safe mode, but even once it just hangs. Then, after having repeatedly tried safe mode and another system restore the computer then hangs when I press F8. After that, the computer passes in front of the Toshiba logo with F2 and F12 options screen (which still works) and then it rises the initialization has failed then shuts off and comes with start-up bootfailed failed with a few numbers and letters, then it goes to a small box entitled menu starting with 4 options. These are some
  Toshiba MK6465GSX HDD/SSD
  CD/DVD MAST * UJ141ES ABD - CMB
  FLOPPY DRIVE
  LAN

  If I press ESC, it passes through the loop of bootfailed and ends at the same screen, if I press on enter "HDD/SSD Toshiba MK6465GSX" then he quickly returned to the screen and at the bottom it says [HDD/SSD Toshiba MK6465GSX] failed.

  I do not understand why it has gotten worse over time. Can anyone think why it occurred and more importantly, how can I get my pc working again? Note: held 0 then start does nothing for me atm

  Best regards, Matthew

  Hello Matthew,.

  To be honest, I agree with Akuma and it could be related to a dysfunction of HDD the error you described, but ensure 100% there s no software problem, you should try the Toshiba Recovery disk Windows installation. Something may be confused until the Windows installation and recovery of files on the HARD drive, so it cannot be started. Recovery disc will resolve this problem by formatting the HARD drive and restoring the settings box.

  If it still doesn t it work s hardware malfunction but an authorized service provider can solve these problems under warranty for free. So just contact the guy and ask for help. ;)

  If you have other questions or already solved the problem, please let us know!

• Satellite L - drive HARD recovery error

  Hello

  If someone could help? I tried to run the hard drive recovery, but he got the following error message.

  Error: F3-FF00-0006
  Unable to get the ID of the specified partition.

  If you know all the keys to enter the hard disk again pls let me know. I tried to enter the Recovery Wizard, but the system continues to operate a diagbostic or something. Ask me to insert the network cable and then also requires a boot disk and keeps current and on. I tried to restart, but it's the same...

  see you soon
  NOx

  Hi nox,

  Strange what s...
  You also have a Toshiba Recovery disk? If so, try it please. Perhaps only something is wrong with the HDD recovery procedure.

  In the worst case, it s associated with RAM or HARD disk as Akuma writes. So download these special testing tools! :)

• HP ENVY DV7-7203SA: problem starting and drive hard smart error

  Hi Ive had problems to start my computer laptop dv7 envy.

  When I run the diagnostic test on the hard drive get a smart error RU5WJO-6K27T-QFPK1F-60AD03 id C1w33EA #ABU

  Finally I have to start, but a few times I had a no device found startup, but only once did I need to reinstall windows 10

  can any body advise on what means this error code and should I look for to replace the hard drive

  concerning

  er65

  HERE IS THE MANUAL for this PC.  Replace hard drive starts on page 48, but indicated that 56 in the area of the manual drive.

  In this same page 100 reported in the box as 108 States "light up the computer or restart the computer, quickly press ESC, then press F10.  This is part of the BIOS information.

  The set of recovery disks will be back as 'new plant' just as it came when new.  No other software is required.  If M$ Office has been installed, maybe check if the disk key and products are always available.

  To the extent where the SSD, do not have the recovery disk set up to automatically accept that in the PC when you run the recovery disk set.  You can try, but I expect to say that the computer has changed and he does not meet the conditions to use the set of recovery disks.

• Drive hard failure - problems of restoration of external hard drive using DBAR

  The hard drive on my Dell Inspiron 15z laptop computer (2.5 years) has just failed and was replaced by a local company. Before the failure I had improved Windows Windows 8 to 10 and according to the recommendations made one full data and the system backup on an external hard drive to Dell backup and recovery assistance. Now that my laptop still works once I'm using backup to restore my data but impossible to find a way to access the information on the external drive using DBAR. Does anyone know how to do this please? Thank you. Tony.

  Thanks for the screenshot. Please refer to this link http://bit.ly/1Fjftmo and take possession of the file to open.