Reference DELL 510 RAID 5 - missing 2 HDD (1 foreign)

Similar Questions

• Reference Dell T300 RAID 1 broken by the firmware update

  Hello

  We have a Dell T300 with the SAS 6/iR adapter.

  We have a RAID1 with 2 x 3 TB drives (visible only 2 TB).

  I have updated the firmware on the SAS adapter to the latest version available here:

  

  and now the RAID 1 has disappeared!

  We have a lot of important data on this virtual drive so any help would be appreciated.

  Thank you!

  Jerry.

  Hi Josh,.

  Thanks for getting back to me. The physical connections and the disks were good and they appeared in the update controller RAID configuration. But the virtual drive RAID1 had disappeared.

  I solved the problem by downgrading to an earlier version of the firmware.

  If I had read the README of the first firmware upgrade page completely, I would have noticed:

  The migration of the SAS 6/iR controllers PERC6 controller RAID Volumes is only supported for volumes created originally on 6/iR controllers SAS running review FW 00.25.47.00 or later version.

  I was able to locate a FW version 00.20.48 here.

  The executable flash.bat refused to downgrade the FW version

  However, looking at the .bat files, I could see that flash.bat called xflash.bat called sasflash.exe which is a LSI utility to upgrade the firmware of the card.

  I found an old manual with the arguments that sasflash.exe take here and use the switch - fwdown to wipe the card and firmware downgrade.

  When the server has started upward the virtual drive was back. Phew!

  Guess I'll read the Readme next time?

  Thank you for your attention,

  Jerry.

• Reference Dell T300 RAID additional Install

  Currently I have a T300 Dell with a RAID 1. Current readers are almost complete, so I have 2 drives more than I am about to install in another RAID 1 on the server. Ask yourself what are the steps needed to do this successfully.

  Currently, I plan the following:

  1 stop server

  2. install the new discs on the front of the server.

  3 Server boot in OS (Server 2008)

  4. use the Dell software to configure new RAID 1.

  Is that going to succeed?

  1 skip this step.

  2. install new disks on the front of the [hot] Server.

  3. no need to 'boot' in OS.

  4 use the Dell [OMSA] software to configure new RAID 1.

• Reference Dell R610 RAID, virtual disk more problems of 1800 GB

  Hello community,

  I was frustrated by my attempt at installing VSphere 4.0 Update 2 (or 1) on a virtual disk on a SAS Perc 6, which is more than 1 800 GB in size and I was wondering if any of you have had similar experiences and how you have handled THIS.

  Unfortunately this system will use internal to the storage drive as it will be in a remote location.

  Any help is greatly appreciated

  Thank you

  Brian Wing

  Calix

  Break your table into smaller pieces. ESX requires a minimum of about 10 GB, even if you can make bigger it. ESXi requires only 1 GB. Data warehouses may not be less than 2 TB. You may be able to use virtual disks raid based to break the table.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Reference Dell E6420 randomly not SSD detection at startup

  Specifications of the computer:

  Dell Latitude E6420, Intel Core i5 2520 M, 2 x 4 GB = 8 GB of RAM, Nvidia NVS 4200 M, 250GB HDD, Win 7 Pro 64, Bios A23

  The value of operation SATA AHCI and not quick start. I have 3 of these computers. They are all out of warranty.

  I replaced the original 7mm Hitachi 250 GB for the Intel 535 240 GB SSD HARD drive.

  I used Acronis True Image 2016 to clone the hard disk SSD. Cloning process is very much like on any other computer.

  The problem is that each cold 4 or 5 boots the computer cannot find the SSD drive. Restarting the computer solves the problem of that time. I have to find a solution. I want to sell them with a SSD and not with a HARD drive.

  I tried the things:

  Update the Bios of the A14 to A23.

  Put a spacer of 2mm on the SSD and of course the resettlement of the SSD.

  Exchange for another Intel 535 120 and 240 GB.

  Clean install of windows I knew was a waste of time because it does not affect the BIOS does not detect not things.

  Googling the problem for hours.

  Call dell?

  Use another brand of SSD? He probobly won't make any difference to look at other threads.

  Use a HARD drive? Last resort. I can't stand slow hard disks regularly.

  Reference Dell E6420 seems to work with a Samsung 850 Evo 250 GB instead of the Intel 535 very well. Tested over a period of 3 months with no problems. Threw 535 readers intel in the desktop instead.

• Reference Dell 6224 and 5448

  Hi team,

  I'm new dell switches - exposed to cisco switches. I am faced with new kinds of problems with these dell switches. Unable to provide a fix and fight for the last 5 days. Pls help me. Below is my script

  Two nw - 2.0 and 3.0 is required to be configured in VLAN, VLAN ID 2 and 3.

  VLAN 2 - 192.168.2.1

  VLAN 3 - 192.168.3.1

  N/W 2.0 and 3.0 N/W machinery will be shared 48-Port powerconnect switch 5448 DELL

  The routing part arrives at 6224 power connect - gateway for vlan 2 - 192.168.2.1 and bridge for VLANs 3 - 192.168.3.1

  The switch of two is ascending through fiber optic - spf port cable

  This is the configuration I did-

  5448 switch-

  database of VLAN

  VLAN 2, 3

  output

  interface vlan 2

  switchport access vlan 2

  GVRP enable

  Routing

  output

  interface vlan 3

  switchport access vlan 3

  GVRP enable

  Routing

  output

  interface ethernet 1/you/1

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  output

  interface ethernet 1/g1

  switchport access vlan 2

  GVRP enable

  output

  interface ethernet 1/g2

  switchport access vlan 3

  GVRP enable

  output

  Uplink port is TE1 (Layer 2) to XG2 (Layer 3)

  Reference Dell 6224 can connect

  Configure the terminal

  interface vlan 2

  no downtime

  IP 192.168.2.1 255.255.255.0

  Routing

  output

  interface vlan 3

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  Routing

  output

  interface ethernet 1/xg2

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  Computer with 192.168.2.100 / 24 GW 192.168.2.1 connected to layer 2 switch g1 - vlan 2

  When I ping 192.168.2.1 - accessible United Nations host destination

  Even the wise

  Computer with 192.168.3.100 / 24 GW 192.168.3.1 connected to layer 2 switch g1 - vlan 3

  When I ping 192.168.3.1 - accessible United Nations host destination

  Any thing that has missed out in the configuration part / all bad entries. I'm not sure now how to treat this. Pls help me and it is an urgent task for me

  Thank you

  With multiple VLANs, you need to use the general/Trunk mode. With the help of the info we have I made a diagram to help show the location of the switches and parameters on them. Obviously things can be different, such as PVID, IP address, VLAN ID etc are all customizable to your needs. But the page layout modes and the port will remain the same.

  

  STP will not fill the VLAN on the other switches. It's probably the GVRP feature it refers. With such a short race, it is more practical to manually add the VLAN. At least for the initial Setup, then once everything works enable GVRP to accommodate future expansion of VLAN.

  Hope this helps some.

• Reference Dell T310 - laboratory home

  Hi all

  I want to buy 2 of the Dell Poweredge T310 server for my laboratory at home to practice and prepare for my VCP certification. Here is the specification I chose and please let me know if this is compatible and I'm good to go set up my lab, I have to make changes to these specifications? I have not ordered any RAID controllers and do I really need?

  PowerEdge T310 chassis with up to 4 hard drives and Quad Pack LED Diagnostics
  Delivery charges for PowerEdge T310
  16 GB 1333 MHz UDIMM memory
  X 3430 Xeon processor, 2.4 GHz 8 MB Cache, Turbo
  PowerEdge T310 heatsink of heat
  No controller
  No operating system
  Gigabit network adapter double built-in
  Controller BMC
  Cable for optical drive SATA for PowerEdge T310
  Integrated SATA, 1-4 hard drives connected to the integrated SATA - no RAID controller

  250GB 7.2 k RPM Serial ATA 3Gbps 3, cable 5po hard drive

  250GB 7.2 k RPM Serial ATA 3Gbps 3, cable 5po hard drive
  Non-redondante 375W PSU

  Thanks in advance,

  I found the focus check tracking if help http://communities.vmware.com/message/1475041

  I am looking in HCL - check result.

  Research: Your search for "Systems" returned 2 results.
  Display:

  Name of the partner	Model	CPU series	Supported releases
  REFERENCE DELL	PowerEdge T310	Intel i3/i5 Clarkdale series	ESX 4.1 U1 4.1 4.1 U1 4.1 ...
  REFERENCE DELL	PowerEdge T310	Intel Xeon 34xx series Lynnfield	ESX 4.1 U1 4.1 4.1 U1

  ? deviceCategory = Server & productid = 10062 & releaseid = 142 & deviceCategory Server = & partner = 23 & keyword = t310 & page = 1 & display_interval = 10 & sortColumn = partner & sortOrder = Asc "> 4.1 ...

  Please, do not forget the points of call of the "useful" or "correct" answers

  Mauro Bonder - moderator

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell Sonicwall SRA

  Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>

  Good thought.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4dell