Replacement of cartridge HP Photosmart 3310 AIO problem

Similar Questions

• I just replaced the black cartridge on my HP Officejet 6310 printer and get a message that I need to replace the cartridge. What is the problem?

  Officejet 6310 printer will not print.

  Again - the cartridge and DATED?  Did you remove all plastic covering the nozzle before insert?  Have you read in the Quick Installation Guide that you have when you first set up the printer?

  If still no joy and it's a genuine HP cartridge, contact HP and get them to replace it.

• HP Photosmart 3310 under VISTA

  I recently move to a VISTA based PC. After installing the printer driver (VISTA version) on the site of it worked fine.

  However after restarting the PC the printer will more be found via SOLUTION CENTER. The printer is removed from the selection of the printer as well.

  This here a patch out to solve this problem?

  Thank you.

  Printer HP Photosmart C7280 all-in-onenot the HP Photosmart 3310 AiO Unit aims URL above.

• HP Photosmart 3310 printer. Problem with new cartridges hp 363 original.

  I live in Italy and I bought an all-in one HP Photosmart 3310 U.S.. Once the original ink cartridges were being run-out, I bought a complete set of original HP ink cartridges that are new in Italy. Now, the printer screen displays the following message: "Printer set up to use ink cartridges 02" and do not want all works. The ink cartridge, I bought was 363 (n.6 cartridges for all 70 euros!). Please let me know if there is a way to change the configuration of the printer and allow it to work with 363 cartridges instead of 02. Thanks in advance for your answer. I'm looking to pass on your instructions. Best regards. Carlo of Urso

  Of course, I can't speak for cdurso, but for my part, HP refused to help me with the reset of the region. Some representatives of the foreign customer support told me simply repeatedly that my printer was obsolete, and that I had to buy a new one. However, I found a solution very simple to my problem. I simply pulled the chip on the ink cartridge in the region that the printer has been set to, and I stuck on my new cartridge. I think that this would negate my ink level readings, but it allows me to use the printer, which now works perfectly. I just have to ignore the "expired cartridge" message I get every time I need to activate or reset it.

• Photosmart 6515 does not print black ink after replaced the cartridge

  I am very frustrated! I can't get my Photosmart 6515 print black ink.

  Our school sends the documents by e-mail now that we have to print at home. Ideal for them, but not for me. They are usually in PDF format, so I do not have the ability to edit and change the blue color to print, either.

  I only use HP cartridges on this printer. I know it's more than a year, in order to call phone support will do no good.

  I replaced both cartridges and now it shows black ink completely full, but when I print the printer status report, black is not displayed. Black does not appear on the tool pages, either.

  I tried the command "clean printhead" several times. I unplugged and waited. I took all the cartridges. Connections look clean.

  What should I do to perform a partial reset or full?

  Hi Photokool,

  I understand that this has been a frustrating experience for you, and I want to help him.

  I will send you a private message, please check the little envelope on the upper right of the forums page to check your Inbox of Forums.

  

• All-in-one HP Photosmart 3310: 2 HP inkjet printers different... same problem

  The time which was formerly set via the network apparently to I remember ever setting the time on one or the other. Today, I noticed for the first time that both of the printer are turned off as follows:

  HP Photosmart 3310 all-in-One - Time is 19:43 locally the printer indicates 19:12 (thirty minutes slow).

  HP Photosmart Premium Fax C309a series - time is 19:43 locally the printer indicates 19:35 (slow 8 minutes).

  Two of these printers previously seemed auto-sync the time on the display panel. Is it possible that my ISP has started to block the NTP port or something?

  Hmm, no, I just connected to 0.pool.ntp.org via ntpdate on my linux machine, and he was not blocked. So it's something on these printers has gone wobbly.

  Hi @tcagle53,

  Thanks for joining the Forums of HP Support with your request for time to printer.

  I understand that you have 2 printers and a HP Photosmart 3310 HP Photosmart Premium Fax, and each printer is showing incorrect. I would like to help.

  The printer usually have the user set the time and Date when the printer is in the configuration. Sometimes things like power outages or to unplug the printer can cause time to read properly.

  You can set the time to the correct time using the printer control panel.

  To set the time on the HP Photosmart 3310 device:

  

  To set the time on the HP Photosmart Premium Fax:

  1. press on the installation program button.

  2. press the button arrow down to select Preferencesand then press OK.

  3. press the down arrow button to select the Date and timeand press OK.

  I was not aware of the printers synchronization automatically at the time of the computer, but sometimes the built-in Web server (EWS of the printer) will have a setting "Synchronize with the time on the PC" that can be selected if the printer is used on a network.

  

  Once the built-in Web server is in charge there should be a tab somewhere near the top of the window.  If you click on Date and time parameters should be able to be selected on the left side. If the sync option of the printer with the computer time is available it usually a checkbox to check before you click apply. Printer not all have this option.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• can replace the cartridge of hp564 to 178 hp C410 series photosmart premium fax e-ALL-IN-ONE?

  Can replace the cartridge of hp564 to 178 hp C410 series photosmart premium fax e-ALL-IN-ONE?

  564 ink cartridges are intended for America, 178 ink cartridges are intended for different regions.

  If you have moved to the Middle ease, African countries or CIS get a full set of 178 ink cartridges, then contact HP sopport to reset the printer to accept local ink cartridges.

  You can find contact information by selecting your region and following technical support after purchase below:

  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  Shlomi

• Photosmart c3150 check ink cartridge blink after replacing the cartridge

  Almost every time I have to replace a cartridge check ink cartridge blinking and I can not find anything wrong.

  If the led check cartridge blinking after changing a cartridge, then there is a document with steps to help solve this problem. The document can be accessed here.

  Hope this helps Richard.

• Print email on photosmart 3310 problem

  I can't copy an email on my photosmart 3310 all in one. When I select print preview mode, the print preview page is empty. When I try to copy the email into a wordpad document, nothing copies the wordpad document.

  Great! I'm glad that the issue is resolved.

• printer Photosmart 3310 says black ink is out. replaced the same message twice.

  My printer says ink is out, but I have replaced the cartridge twice, cleaned the contacts, clean the print head and says the same thing. I was the impression of the things that I have in choosing the black mark of another color option, but last night he left the impression at all.  Indicates the ink level is dangerously low and could cause injury.  I always use hp ink cartridges. Please help don't want to replace the printer if I have to.

  Hello

  The ink is blocked somewhere and not out of the print head. or the ink flowing from somewhere inside the printer.

  Open the lid to see the inside of the print mechanism. to the left of the printer, you should be able to see the tubes. see if any of them escape (without touching it).

  If the black ink is always full, but the printer says empty, then ink is blocked somewhere.

  Whatever it is. I'm sorry, but the printer looks like it will replace.

• HP Photosmart 3310 all-in-one does not print print test page doe but doesn't show is not black

  I have a printer all-in-one HP Photosmart 3310 that does not correctly print a test page (print color but not black) and does not print a WORD document from my computer.  The color that should be black in the test page after CLEANING print head appears as a Purple-ish Brown, although after the PRINTER SNAP the printed page shows a short BLACK bar to the left of the five longer bars in FIVE COLORS.  The computer in use is a HP Pavilion dv7 with processor Intel Core i7-3610QM, 2.3 GHz, Ram 8. 0 GB (7.9 GB available), 64-bit and Win 7 Home Premium OS, SP1.

  After having downloaded HP Print and Scan doctor, we arrived, after a series of steps to "If the cartridges have been refilled and none is empty, try calibration of color": Open HP Solution Center (start, all programs, HP, HP Solution Center), then click on settings, settings, printer Toolbox, printing on the tab device Services, click on color to calibrate.  This procedure is NOT AVAILABLE, however, because I can't find the HP Solution Center.

  What should I try to fix this problem?  Please be specific - and please also include any recommendations for a remedy that is exactly what happens if something must be verified or checked before trying the recommended remedy.

  Since the last post, I repeated the test several in Solutions of HP.  Whenever I have repeated the procedure clean print heads, improve the quality of printing in black ink a little bit.  After several passages of this test, maybe 5 or 6 more and separated by some rest of the time, the quality of printing in black ink has reached the State that I consider finally acceptable.

  A variable that I can't rule out or rule through all this is the temperature and the humidity.  It has been a winter VERY exceptionally difficult, with a lot more than zero days and subzero temperatures.  And with that comes challenges with the indoor humidity (even if we have the whole House humidification).

  In all cases, the printer now works without problem.  And I'll post that I accept the solution most recently proposed by the HP Forum.

• Photosmart 7510 alignment problem

  Hello

  I'm having a problem with my photosmart 7510.

  The screen an error alignment and the alignment and cleaning do not work.

  Is there something else to do? or should I buy a new printer?

  Thank you

  I called HP support 1-800-474-6836 and spent a few hours with their support to the execution of diagnostic tests.

  They recommended a replacement of the printer because basic troubleshooting has not helped.

  We power off of the pritner (power disconnected) and held the power button for 30 seconds.

  power turned back and removed printer cartridges and printerhead. Clean any electronic contact with a cloth and put back them.

  Also replace photo cartridge that was less than 30%.

  The alignment is still not.

• Photosmart 3310 printing issue - apparently ink leaks and failures of alignment

  Hi, sorry to bother but I am facing a problem with an All - In - One Photosmart 3310.

  -I am running windows XP.

  -L' printer is connected to several for my private with band wifi LAN.

  N ' got no code error on the question

  -All used within the printer cartridges are genuine HP and photo paper was also 10 x 15 HP (the one provided with the packs of cartridges).

  -L' printer is a little over 4 years now and he has his crazy suddenly two days ago. The printer has not been moved or damaged, it simply sound suddenly started printing blue black & white text characters and ended with the ink.

  As I have already experienced similar problems with some other printers, I well as cleaning cartridges and lining up, but it has not changed anything. I finally changed all 6 white ink by new ones, but all the same. I cleaned again, tried to align, but once again, no possible way to achieve alignment. "Alignment failed" came out at this stage.

  Here are some pictures to illustrate because I tried several impressions to make sure it wasn't a short-term problem be resolved with cleaning or alignments: photo printer problem

  It should be noted that no two prints come out the same way, some are mainly blu, other yellow or green...

  At this point, I didn't Kow where to start with this problem. There seems to be a leak in the print head (assuming that the magenta) and another leak with the blue wire (it can not see on the pictures, located at the bottom of the left hand side, but could not get any pic suited because of the plastic on the printer cover.

  So, I'm wondering the following things:

  -What a sound suddenly went to the printer?

  -It worth repair?

  -How to proceed?

  Any ideas? Thanks in advance for reliable advice.

  Alignment is probably a failure because of the incorrect colors being printed on the page. The printer scans each line or section of the alignment page using a special sensor inside the printer and check all colors from ink and their bosses and investment. If one of them is not what the printer is expected to be, the alignment will fail. I don't know what film you're referring. But I don't think it matters, as the cause of the failure of the alignment is quite obvious.

  I don't think it's possible for you to do something to solve this problem. Take it to a service center would be a better option, cos they have the tools and the expertise and training to do such things.

  The upgrade process differs from one country to another. I'm not sure of European countries, but in the United States, you can call the support technology and upgrade to a new printer with similar features as yours. HP has TS lines for printers, which is very different from Smart Friend. You must pay any fees to call them and talk to them. If you are in the United States, call 1-800-474-6836 and choose Photosmart all-in-One printer as your product to be transferred to the printer Dept

• Incompatible cartridge (HP Photosmart C4480)

  I don't have the luxury of wasting my time here, I'm supposed to write an article for an academic journal, but let's do it anyway. because I'm pretty annoyed for this give actually the few minutes that I let myself before another staff meeting.

  A week ago, my printer (HP Photosmart C4480, almost a year now) began to give me the message that my cartridge is incompatible. The cartridge has been about a month or two old that I think, and I printed with her until he was about ¾ of his initial resistance. I followed all the steps troubleshooting gave me; reset, cleaning, I even had my old cartridge rest to see if this one has worked and that he could solve the problem (it worked, one that came with the printer, but it does not solve the problem). Apart from the replacement of the cartridge or get a new printer, it is not a way to solve this problem.

  But get a new cartridge doesn't just prolong the problem without actually solving. Now, it has become more obvious to me that there is a general problem of HP printer with error message "incompatible cartridge". This forum alone shows many examples unresolved for anyone who cares to look for them for a few seconds. The result is that people simply buy or request for new cartridges, and then, either immediately or after a certain while, the error recurs.

  It was an a little more vital product, like say a car, it must be recalled. If you take a look at the Amazon comments, they have been regularly in downhill, becoming more and more negative, the way a few months ago. I don't know if it's a software thing you guys has changed, or if your hardware or cartridges are doomed to failure. Maybe you send a bad batch of cartridges, but that would not explain why recurring popular printers fail with the same message.

  I am currently waiting for a response to a request for assistance. As I shine since other posts about this problem, you can not give a) an explanation of this debacle, b) a solution that does not involve the purchase of new cartridges to replace a cartridge that was perfectly fine before mounting them in your cartridge deathtraps. If there is anything that can be done does not mean to ignore the problem, spending more money on more product failure, but actually goes one way to solve the problem, I have he would hear gladly.

  OK laddie and gentlemen listen hear is how to fix this error message "incompatible cartridge" boring.
  Step 1: turn off your printer
  Step2:turn on your printer
  Step3:hold to the bottom of the button works / stop and the 'x' button - you will receive a message prompting you to "enter special key combination.
  Step 4interested "blue-> green-> ORDER BECAUSE gray!
  Step 5NCE "support rhLxFN0810CR" message is displayed 'blue' push the button once until appears the menu information
  Step 6interested 'ok' now using 'blue' new button scroll until you see "checksum for repo I input data ' appears
  STEP7interested ok and a code number will be displayed (note code will change each time this spice is used)
  Step8nce code appears press 'x' 3times to return to the main display screen. You are now ready to print as usual! if the print head is allowed to return before next print this process should be repeated every time print head reset

• error cartridge hp photosmart a516

  1 HP Photosmart A516

  2. Windows XP

  3 cartridge is missing. Please install and snap the cartridge in completely.

  4. no

  5. the printer works well. When I bought a new cartridge (hp 110) I installed it as I did before. But now the printer does not work; It stops with the error message above. How can I get by this problem?

  Hello, I will try to replace the cartridge with a new one and then print the alignment page. I will return to you as soon as I got the new cartridge.