Restrict the Anyconnect to IPSEC

Similar Questions

• ASA5505: Configure the ASA for IPSec and SSL VPN?

  Hello-

  I currently have my 5505 for SSL AnyConnect VPN connections Setup.  Is it possible to set up also the 5505 for IPSec VPN connections?

  So, basically my ASA will be able to perform SSL and IPSec VPN tunnels, at the same time.

  Thank you!

  Kim,

  Yes, you can configure your ASA to support the AnyConnect VPN IPSec connections and at the same time.  In short, for the configuration of IPSec, you should configure at least a strategy ISAKMP, a set of IPSEC, encryption, tunnel group card processing and associated group policy.

  Matt

• Redundancy ASA - Client to the remote access (AnyConnect or IPsec) VPN Cisco to 2 PSI

  Hello

  I realize that the true public access redundancy require routers and BGP need &AS#; but some can't afford such a solution.  Should someone have ASA 5510 dry + with 2 of the ISP could use IP SLA functionality for primary education to save the failover, etc..  What VPN clients for remote access (SSL or IPSec).  I'm curious if you have any other solutions/configurations on it to allow either of these customers, AnyConnect or IPsec, to try the primary counterpart and after a few failed attempts over fail to backup (even if a user tries to establish a VPN)?  I know that one of the possible solutions may use a domain name FULL peer IPSec or AnyConnect client input, then maybe public operator DNS TTL change or other hosted / failover services... but these "proxy" or DNS services are not the best solution because there is cache and other associated DNS weaknesses (right)?  These are not infallible fail-over, I'm sure that some users might succeed and some may fail; I do not know administrators will be like that as much as they like going to the dentist.

  Anyone who has any ideas or possible solutions?

  Thank you.

  Hello

  Backup servers are supported by remote access VPN clients.

  The client will attempt to connect to the first IP/configured FULL domain name and will try the following in the list, if no response is received.

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client46/win/user/guide/VC4.html#wp1000747

  Federico.

• How to restrict the use of the connection profile Anyconnect to traffic from an interface?

  Hello

  A few questions about the profiles connection Anyconnect and dynamic access policies:

  • I set up multiple profiles connecting Anyconnect with different characteristics. I want one of the profiles to be visible and usable only when the Anyconnect client connect through a specific interface (and not the outside interface). How can this be configured? As it is now all profiles are visible via all interfaces compatible VPN.
  • DAP: When dynamic access policies are configured, these will be global or is it possible to link a policy to a specific connection profile? I would like to configure the DAP Protocol to be effective only when you use a specific connection profile. What is a good way of thinking? What I want is: when a user Anyconnect choose a specific connection profile, it needs to connect using a DAP which requires membership in an ad group and existence of a local file.

  Best regards

  Thor-Egil

  • Unfortunately, you cannot restrict the interfaces of the AnyConnect fitting profile is assigned to AnyConnect connection profiles are global settings, no interface specific setttings, therefore, it will be available no matter what interface the AnyConnect is connected to.
  • DAP political work as an access list. It in the lowest priority to highest priority and he stops at the first match. For example, you can create a number of policies on what you want to match on. You cannot however force the user to authenticate to AD when they choose a specific group of tunnel. DAP is used to apply that only users that meets policy is allowed access. For example: If the user belongs to a specific ad group and also have a file exist, the user will be allowed access to use the AnyConnect. So it's the application that the user connects from a company laptop where you specified the policy, that is to say: exist in AD and have a specific file in his laptop. This is to ensure that those who try to connect to the site of the company non-portable, or internet kiosk have accessed to the VPN, because they may not be protected and can infect your corporate network, if they are allowed to access.

  Hope that makes sense.

• Cisco AnyConnect do IPsec?

  Hi guys

  I have a Cisco ASA5520 with software Version 8.2 (5) in place, most my users are Mac users and I am currently looking into Cisco AnyConnect in comparison using the VPN client.

  I have a few questions

  (1) Cisco AnyConnect does he use IPSec or is it soley based SSL VPN?

  (2) the license information I have in my ASA below, I understand that I can get max 750 vpn peers am however I have reason to say that this does not apply to Cisco AnyConnect peers? and with Cisco AnyConnect, I can only have 2 peers? Also, what are the options for mobility anyconnect for?

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 150

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  SSL VPN peers: 2

  Total of the VPN peers: 750

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  (3) when you try to configure Cisco Anyconnect on the SAA by using ASDM, I noticed that I needed to download AnyConnect client images, but when I did this by downloading the .dmg for mac machines file I got the error message 'not an image valid of the SVC'. Is it because I'm under 8.2?

  Your help is highly appreciated

  Concerning

  Mohamed

  Hi Mohammad,.

  I'll answer your questions one by one:

  1 cisco Anyconnect version 3.0 and above all support SSL and IPSECv2 connection. If you want the user to connect using the Anyconnect client IPSECv2 then it will consume the SSL license and not the IPsec license however if you use IPSECv2 for connections such as vpn site to site then it will consume normal IPSec VPN license.

  2. one.  SSL VPN peers: this license gives you information about the number of users that can connect using SSL protocol for example using the Anyconnect and web portal customer also known as the clientless VPN based on. I see here there are only 2 licenses so at any given time only 2 users can connect successfully because 750 is the total number of licenses available for the VPN on the SAA, 698 only will be available for IPSec connections.

  b. Anyconnect for mobile: this license is required whenever a user connects from a Pocket like device: Iphone, Ipad, tablets etc.

  c. Anyconnect of Cisco VPN phone: Cisco IP phones have the ability to connect to an ASA remote using the SSL protocol and to enable this feature, you should have this license is activated on the SAA.

  d. Anyconnect essentials: Anyconnect there are two licenses, one > Anyconnect Premium and b > Anyconnect Essentials. AnyConnect essentials is less expensive as premium per report Anyconnect license. This license is for those who don't use webvpn or VPN without client. When the license is activated, the user can connect only to the Anyconnect VPN client.

  3. I don't know what image you use on the ASA. Please try the image named as anyconnect-macosx-i386 - 2.5.2010 - k9.pkg.

  To apply the changes using the command line, put this image on disk0: and then type this command on the CLI.

  Image disk0:/anyconnect-macosx-i386-2.5.2010-k9.pkg SVC

  Let me know if it helps.

  Thank you

  Vishnu Sharma

• The anyconnect vpn easy vpn Remote communication problem

  Hi team,

  I have a problem of communication of the anyconnect vpn easy vpn Remote I´ll explain better below and see the attachment
  topology:

  (1) VPN Tunnel between branch HQ - That´s OK
  (2) VPN Tunnel between Client AnyConnect to HQ - that s OK

  The idea is that the Anyconnect Client is reaching the local Branch Office network, but has not reached.
  Communication is established just when I begin a session (icmp or rdp) branch to the AnyConnect Client,.
  in this way, the communication is OK, but just for a few minutes.

  Could you help me?
  Below the IOS version and configurations

  ASA5505 Version 8.4 (7) 23 (Headquarters)
  ASA5505 Version 7.0000 23 (branch)

  Configuration of the server easy VPN (HQ) *.

  Crypto dynamic-map DYNAMIC - map 5 set transform-set ESP-AES-256-SHA ikev1
  Crypto card outside-link-2_map 1 ipsec-isakmp DYNAMIC-map Dynamics
  Crypto map link-outside-2_map-65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  Crypto map interface outside-link-2_map outside-link-2

  ACL_EZVPN list standard access allowed 10.0.0.0 255.255.255.0
  ACL_EZVPN list standard access allowed 192.168.1.0 255.255.255.0
  ACL_EZVPN list standard access allowed 192.168.50.0 255.255.255.0
  ACL_EZVPN list standard access allowed 10.10.0.0 255.255.255.0

  internal EZVPN_GP group policy
  EZVPN_GP group policy attributes
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list ACL_EZVPN
  allow to NEM
  type tunnel-group EZVPN_TG remote access
  attributes global-tunnel-group EZVPN_TG
  Group Policy - by default-EZVPN_GP
  IPSec-attributes tunnel-group EZVPN_TG
  IKEv1 pre-shared-key *.

  object-group network Obj_VPN_anyconnect-local
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.15.0 255.255.255.0
  object-group network Obj-VPN-anyconnect-remote
  object-network 192.168.50.0 255.255.255.0
  the NAT_EZVPN_Source object-group network
  object-network 192.168.1.0 255.255.255.0
  object-network 10.10.0.0 255.255.255.0
  the NAT_EZVPN_Destination object-group network
  object-network 10.0.0.0 255.255.255.0
   
  destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

  Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
  destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

  NAT_EZVPN_Destination no-proxy-arp-search to itinerary
  NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

  NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

  Configuration VPN AnyConnect (HQ) *.

  WebVPN
  Select the outside link 2
  by default-idle-timeout 60
  AnyConnect essentials
  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
  AnyConnect profiles Remote_Connection_for_TS_Users disk0: / remote_connection_for_ts_users.xml
  AnyConnect enable
  tunnel-group-list activate

  tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.15.0 255.255.255.0
  tunnel of splitting allowed access list standard 10.0.0.0 255.255.255.0

  internal clientgroup group policy
  attributes of the strategy of group clientgroup
  WINS server no
  value of server DNS 192.168.1.41
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  ipconnection.com.br value by default-field
  WebVPN
  AnyConnect Dungeon-Installer installed
  time to generate a new key 30 AnyConnect ssl
  AnyConnect ssl generate a new method ssl key
  AnyConnect value Remote_Connection_for_TS_Users type user profiles
  AnyConnect ask flawless anyconnect

  type tunnel-group sslgroup remote access
  tunnel-group sslgroup General-attributes
  address vpnpool pool
  authentication-server-group DC03
  Group Policy - by default-clientgroup
  tunnel-group sslgroup webvpn-attributes
  enable IPConnection-vpn-anyconnect group-alias

  object-group network Obj_VPN_anyconnect-local
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.15.0 255.255.255.0
  object-group network Obj-VPN-anyconnect-remote
  object-network 192.168.50.0 255.255.255.0
  the NAT_EZVPN_Source object-group network
  object-network 192.168.1.0 255.255.255.0
  object-network 10.10.0.0 255.255.255.0
  the NAT_EZVPN_Destination object-group network
  object-network 10.0.0.0 255.255.255.0
   
  destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

  Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
  destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

  NAT_EZVPN_Destination no-proxy-arp-search to itinerary
  NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

  NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

  Hello

  communication works when you send the traffic of easyvpn derivation because it froms the IPSEC SA to pool local subnet and anyconnect HQ. The SA formed only when the branch initiates the connection as it's dynamic peer connection to HQ ASA.

  When there no SA between branch and HQ for this traffic, HQ ASA has no idea on where to send the anyconnect to network traffic.

  I hope this explains the cause.

  Kind regards

  Averroès.

• How to move the ASA of IPSEC VPN via UDP to TCP

  I have a client who has a remote desktop with 2 PCs than VPN in to their location of HQ. Previously, two computers where in different places now that they are in the same place. Both PC's are able to successfully establish a VPN connection to the CA by using the Version of the Client VPN Cisco 5.0.07.0290, but only 1 system actually passes the traffic and is able to access the resources at Headquarters.

  I asked another engineer, and they said ' you must configure IPSEC over TCP or use Anyconnect to have multiple clients behind the same PAT' public ed remote ip address... ". ». I would go with IPSEC for TCP connection, so I won't have to uninstall the old client and go through the process of installing the AnyConnect client. Here is the configuration of the ASA 5505 thanks in advance for any help.

  CLIENTASA # sh run

  : Saved

  :

  ASA Version 7.2 (4)

  !

  hostname CLIENTASA

  domain client.local

  activate 72LucMgVuxp5I3Ox encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x where x.x.x.x

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain client.local

  standard SPLIT-TUNNEL access list permit 192.168.1.0 255.255.255.0

  outside_in list extended access permit tcp any any eq smtp

  outside_in list extended access permit tcp any any eq www

  outside_in list extended access permitted tcp everything any https eq

  access-list extended sheep allowed ip 192.168.1.0 255.255.255.0 10.99.99.0 255.255.255.0

  pager lines 24

  Enable logging

  recording of debug console

  debug logging in buffered memory

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  pool local IP VPN-10.99.99.100 - 10.99.99.200

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 523.bin

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (inside) 1 0.0.0.0 0.0.0.0

  public static tcp (indoor, outdoor) interface www 192.168.1.2 netmask 255.255.255.255 www

  public static tcp (indoor, outdoor) interface https 192.168.1.2 netmask 255.255.255.255 https

  public static tcp (indoor, outdoor) interface smtp 192.168.1.2 netmask 255.255.255.255 smtp

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  AAA authentication enable LOCAL console

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-3des esp - esp-md5-hmac

  Crypto dynamic-map VPNDYN 1 set transform-set esp-3des

  vpn ipsec dynamic VPNDYN 65535-isakmp crypto map

  vpn outside crypto map interface

  crypto ISAKMP allow outside

  crypto ISAKMP policy 100

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 5

  Console timeout 0

  dhcpd dns 192.168.1.2

  dhcpd outside auto_config

  !

  des-sha1 encryption SSL rc4 - md5

  VPN-POLICY group policy interns

  attributes of VPN-POLICY-group policy

  value of server DNS 192.16.1.2

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value of SPLIT TUNNEL

  admin PWpqnmc2BqJP9Qrb encrypted privilege 15 password username

  password encrypted vpn2 ZBNuNQsIyyMGbOB2 user name

  username vpn3 encrypted password 15c4LrPNccaj1Ufr

  vpn1 fsQgwXwSLokX6hEU encrypted password username

  tunnel-group CLIENTVPN type ipsec-ra

  attributes global-tunnel-group CLIENTVPN

  address VPN-POOL pool

  Group Policy - by default-VPN-POLICY

  IPSec-attributes tunnel-group CLIENTVPN

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:41bd95c164a63bb26b01c109ab1bd68a

  : end

  CLIENTASA #.

  Hello

  You can try adding

  Crypto isakmp nat-traversal 30

  And test connections

  I think that you need to add to use the TCP protocol

  Crypto isakmp ipsec-over-tcp 10000

  You will also need to change the Transparent tunnel setting on the profile of Client VPN software to use TCP instead of option of NAT/PAT.

  -Jouni

• Access via L2L AnyConnect VPN IPSec

  I'm trying to connect two ASA 5505s for a IPSec L2L VPN.  They can connect, but not pass traffic from the AnyConnect subnet. I've added the config from ASA-2, with the LAN subnet of 192.168.138.0 and a subnet of 192.168.238.0 for AnyConnect client. I'm trying to get the AnyConnect Clients access to the 192.168.137.0 LAN behind ASA-1 at 1.1.1.1.  Having both 192.168.238.0 and 192.168.138.0 both access 192.168.137.0 is acceptable. There's probably a lot of cruft in this config, as I've been reading all over forums and docs without much success.  Can someone point me in the right direction? : ASA Version 8.2(1) ! hostname asa-wal names name 192.168.238.0 anyconnect-vpn ! interface Vlan1 nameif inside security-level 100 ip address 192.168.138.1 255.255.255.0 ! interface Vlan11 mac-address c03f.0e3b.1923 nameif outside security-level 0 ip address 2.2.2.2 255.255.255.248 ! same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service Munin tcp-udp port-object eq 4949 object-group service Webmin tcp port-object eq 10000 access-list inside_nat0_outbound extended permit ip 192.168.138.0 255.255.255.0 any access-list icmp_ping extended permit icmp any any echo-reply access-list icmp_ping extended permit ip 192.168.138.0 255.255.255.0 any access-list split-tunnel standard permit 192.168.138.0 255.255.255.0 access-list 100 extended permit icmp any any echo-reply access-list 100 extended permit icmp any any time-exceeded access-list 100 extended permit icmp any any unreachable access-list NO_NAT extended permit ip anyconnect-vpn 255.255.255.0 any access-list NONAT extended permit ip 192.168.138.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list outside_access_in extended permit tcp any interface outside eq ssh access-list outside_access_in extended permit icmp any any echo-reply access-list outside_access_in extended permit icmp any any time-exceeded access-list outside_access_in extended permit icmp any any unreachable  access-list outside_access_in extended permit tcp 192.168.137.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list outside_1_cryptomap extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 192.168.138.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list LAN_Traffic extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list vpn_nonat extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 ip local pool AnyConnect 192.168.238.101-192.168.238.125 mask 255.255.255.0 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 2 access-list vpn_nonat nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface ssh 192.168.138.4 ssh netmask 255.255.255.255 access-group icmp_ping in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 2.2.2.1 1 dynamic-access-policy-record DfltAccessPolicy network-acl inside_nat0_outbound network-acl NO_NAT aaa authentication ssh console LOCAL http server enable http bobx-vpn 255.255.255.0 inside http 192.168.137.0 255.255.255.0 inside http 192.168.1.104 255.255.255.255 inside http 192.168.138.0 255.255.255.0 inside http anyconnect-vpn 255.255.255.0 inside http redirect outside 80 no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set Wal2Box esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 98.110.179.36 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map Wal2Box 1 match address LAN_Traffic crypto map Wal2Box 1 set peer 98.110.179.36 crypto map Wal2Box 1 set transform-set Wal2Box crypto map Wal2Box interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 10 authentication pre-share encryption des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 22 telnet timeout 5 ssh 192.168.138.0 255.255.255.0 inside ssh timeout 30 console timeout 0 management-access inside dhcpd dns 8.8.8.8 8.8.4.4 dhcpd auto_config outside ! dhcpd address 192.168.138.101-192.168.138.132 inside dhcpd dns 8.8.8.8 8.8.4.4 interface inside dhcpd lease 86400 interface inside dhcpd domain inc.internal interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 129.6.15.29 ntp server 129.6.15.28 prefer webvpn enable inside enable outside anyconnect-essentials svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable tunnel-group-list enable group-policy DfltGrpPolicy attributes vpn-filter value NO_NAT vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-network-list value split-tunnel webvpn   svc compression deflate group-policy Wal-AnyConnect internal group-policy Wal-AnyConnect attributes split-tunnel-policy tunnelspecified split-tunnel-network-list value split-tunnel tunnel-group DefaultRAGroup general-attributes address-pool AnyConnect default-group-policy Wal-AnyConnect strip-realm strip-group tunnel-group AnyConnectClientProfile type remote-access tunnel-group AnyConnectClientProfile general-attributes address-pool AnyConnect default-group-policy Wal-AnyConnect tunnel-group AnyConnectClientProfile webvpn-attributes group-alias AnyConnectVPNClient enable tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 ipsec-attributes pre-shared-key * ! class-map global-class match default-inspection-traffic ! ! policy-map global-policy class global-class   inspect pptp ! Cryptochecksum:762f0186ad987cda4b450f6b4929cb60 : end 

  Post edited by: Shawn Barrick - line breaks

  It seems good Shawn but I just noticed an error on the asa-wal, you have a vpn-filter applied on the DfltGrpPolicy and since you have not any value defined the strategy of Wal-AnyConnect group then will inherit the DfltGrpPolicy vpn-filter, don't forget that the vpn filters should be applied to the incoming direction, I mean pool resources you want them to have access to. It's the ACL you have for the filter:

  NO_NAT list extended access allowed anyconnect vpn - ip 255.255.255.0 everything

  This isn't in the inbound direction, increasingly looks like you want to allow access to what it is as long as the traffic is coming from the 192.168.238.0, if that's the case, you can do this:

  attributes of Group Policy DfltGrpPolicy

  VPN-filter no

  Do not forget to disconnect and reconnect after the above change...

  If you really need to be more specific, allowing traffic for clients then apply the inbound rules, for example:

  Your pool is here 192.168.238.0/24 and the local subnet is 192.168.138, to this effect, the 192.168.137 is considered to be local too because of the perspective Anyconnect we'll see in the room even if it is a remote network accessible via a L2L tunnel of the Anyconnect client does not.

  The following AS will allow the Anyconnect Telnet client for local networks:

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 192.168.138.0 255.255.255.0 eq 23

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 192.168.137.0 255.255.255.0 eq 23

  The following ACE will allow local networks of Telnet for the Anyconnect Client:

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 eq 23 192.168.138.0 255.255.255.0

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 eq 23 192.168.137.0 255.255.255.0

  Note that the two first ACE will allow LAN launch connection to the Anyconnect client on any TCP port if he uses a source 23 port while the last two ACEs allow the Anyconnect client connect to networks the on any TCP port if he uses a port source from 23.

  Kind regards

• Username, preserved in the AnyConnect Client user name dialog box

  I have one question remains on my client anyconnect 2.5.2006. The user in the dialog box name is cached. We do not want to be cached and have users to enter their username every time.

  Shilpa Gupta mentioned on another post of mine. I was wondering if anyone has any other thoughts! The 2.5.2006 resolved customer I had another question, so come back to 2.4 is not an option at this point.

  For clearing up the credentials in the dialog box when using AnyConnect I found one of the bug:-
  
  CSCsx76993
  
  

  Symptom:

  User credentials are cached in the preferences.xml file when you use the Anyconnect client.  So when they revive Anyconnect, the user name is displayed in the client.

  Conditions:

  You can see all the client anyconnect.  It is a configurable option in the IPSec client.

  Workaround solution:

  Currently there is no work around

  And I can see it resolved in 2.4.202 however, I'm not sure if its fixed in 2.5 also. For this I would like to hear from others.

  Kind regards

  Shilpa

  Hello

  All bug fixes and new features in 2.4.x are also in 2.5.

  However the "bug" Shilpa has pointed out, is not really a bug, but an enhancement request, in other words in 2.3 before the cached username is expected behavior and is always the default behavior in the 'fixed' versions, so just the upgrade won't change anything. What has changed is that now you can change the behavior by defining a new parameter RestrictPreferenceCaching in the local policy file:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect25/Administration/Guide/ac04localpolicy.html#wp1055429

  So for example the addition

      All
  
      

  your local police should achieve what you want.

  HTH

  Herbert

• restrict the scaling axis in the xy graph

  Hi all

  After you apply due diligence in analyzing the context-sensitive help, labviewwiki and these fine forums, I couldn't find a hint on how to do this:

  I like tor would restrict the scale of only the value of a XY Chart axis. Or, to put it in other words, I want the user to be able to zoom and navigate a signal in the time domain, the realm of values must remain fixed to a pair of mini/maxi - assume that the 0-100% for simplicity. Ideally, I would like to use the graphic palette for this.

  Here's what I tried, with the result

  -disable the range => Y scale: no such property

  -catch the "Change of scale of measurement" event and game of scaling to a fixed value => glitter, the property cannot be changed AFTER that the GUI has already redesigned it

  -change the graphic palette of customization of the control is => not possible

  -set the Disabled State-online graphic palette no longer works

  Thanks for any input. I hope I'm missing something really basic here.

  I don't see an easy way to lock the pan function. You can set the minimum and maximum, but - as you said earlier - you get a jumpy (flashing) chart. Even if the update rate is very high.

  If I (or someone else) comes up with something, we'll let you know.

  Apart from the use of an ActiveX (ActiveX 2D chart) or .net component - they have their own unique problems. Perhaps that is a possibility.

  Rob

• Restrict the automatic download at specific times of the day

  Is it possible in Windows 7 Home Premium for restrict the update of Windows automatic download at certain times of the day? I know I can set the time it INSTALLS updates, but I want the time it DOWNLOADS the updates...  Even with PIECES try to intelligently determine when is the right time to download updates, I would like to restrict them to download only during the first hours of the AM.

  N °

  That being said, you can change you updates automatic setting Automatic to download updates but let me choose whether to install them. After this, no updates will be installed without your approval. See http://windows.microsoft.com/en-us/windows7/Change-how-Windows-installs-or-notifies-you-about-updates

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• How to restrict the running command prompt?

  How to restrict the running command prompt?

  I already know the method: HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\System DisableCMD: 2

  but, but, it is possible to change reactivate cmd used much the system tool software

  So I want to deny the change of registry value by the software used, I changed all permissions to the registry [System] refusal keys with my account.

  but after a modified registry key permissions denied, disableCmd was inactivated more.

  It is impossible that the two parameter [disablecmd: dword = 2] and [{System} lock keys: administrator of the deny all permissions in my account]?

  This issue is beyond the scope of this site which is for the consumer to related issues.
  To ensure that you get a proper answer, ask either on the Technet site, if it is a type of Pro problem, or MSDN if it's related to the developer
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Restrict the possibility to send to the public mailing list

  What is the best way to limit subscribers of voice mail to send a voice message broadcast message? My first impressions are to use MS Exchange to restrict the ability to send to a Distribution list and restrict to the list of users specifice. Example: 600 + site user with a public Distribution list. Only human resources should have the possibility to send a voice message broadcast... you wouldn't want a disgruntled employee to send a broad system voicemessage.

  You can restrict users to a Service class to send messages to the list of distribution _any_ - what causes the conversation addressing do not offer DLs when users are searching by name or ID. There is no way 'cherry pick' DLs and decide that a user can leave messages for certain distribution lists, but not others.

  Yes, you can also do it in the Exchange and sending fails (the user will receive a nondelivery report, however, which is perhaps not ideal).

• Cannot ping the Anyconnect client IP address to LAN

  Hi guys,.

  I have an old ASA5520 running 9.1 (6) 8 where I installed Anyconnect SSL split tunneling access:

  See establishing group policy enforcement
  attributes of Group Policy DfltGrpPolicy
  VPN-tunnel-Protocol ikev1, ikev2 clientless ssl

  lanwan-gp group policy internal
  gp-lanwan group policy attributes
  WINS server no
  DNS server no
  VPN - connections 1
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value lanwan-acl
  by default no
  WebVPN
  AnyConnect value lanwan-profile user type profiles

  permit for line lanwan-acl access-list 1 standard 172.16.0.0 255.254.0.0 (hitcnt = 48) 0xb5bbee32

  Now I can ping, RDP, etc. of any VPN host connected to any destination within 172.16.0.0 255.254.0.0 range.

  Here is my routing information:

  See the road race
  Route outside 0.0.0.0 0.0.0.0 69.77.43.1 1
  Route inside 172.16.0.0 255.254.0.0 172.25.8.1 1

  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  IP 172.25.8.4 255.255.254.0

  But I can't ping any Anyconnect VPN client connected from my LAN.

  See the establishment of performance ip local pool

  mask IP local pool lanwan-pool 172.25.9.8 - 172.25.9.15 255.255.254.0

  Here's the traceroute of LAN:

  C:\Users\Florin>tracert d 172.25.9.10

  Determination of the route to 172.25.9.10 with a maximum of 30 hops

  1 1 ms<1 ms="" 1="" ms="">
  2<1 ms="" *=""><1 ms="">
  3 * the request exceeded.
  4 * request timed out.

  While the ASA routing table has good info:

  show route | I have 69.77.43.1

  S 172.25.9.10 255.255.255.255 [1/0] via 69.77.43.1, outdoors

  Other things to mention:

  -There is no other FW between LAN and the ASA

  -There is no FW or NAT configured or enabled on this ASA(see her running nat and see the race group-access they return all two virgins).

  -FW Windows on the Anyconnect workstation is disabled (the service is running). I also tested and able to ping to my workstation Anyconnect House of another device on the same network.

  So, I'm left with two questions:

  1. first a I do not understand: after reading some threads here, I added this line standard lanwan-acl access-list allowed 69.77.43.0 255.255.255.0

  out of ping and tracert commands remains the same, but now I can RDP to the docking station VPN connected to any workstation LAN;

  What happens here?

  2. how can I do ICMP work after all? I also tried fixup protocol icmp and icmp Protocol Error Correction, still no luck

  Thanks in advance,

  Florin.

  Hi Florin,

  The entire production is clear enough for me

  in debugging, you can see that traffic is constituent of the ASA

  "Inside ICMP echo request: 172.17.35.71 outside: 172.25.9.9 ID = 22 seq = 14024 len = 32.

  the SAA can be transferred on or can be a downfall for some reason unknow

  can we have a wireshark capture on the vpn client to see if the icmp request is to reach the customer? I want to just isolate the problem of fw so that we can concentrate on the ASA rather than silly windows ;) fw

  made the RDP Protocol for VPN client for you inside the LAN work?

  run logging on ASA and ping and then inside to VPN client and the Coachman connects on the firewall, if ASA comes down the pkt it will appear in the log.

  loggon en
  debug logging in buffered memory

  #sh logging buffere | in icmp

  #Rohan

• Hide the AnyConnect VPN AnyConnect GUI Module

  Dear team

  We are wired deployment 802. 1 x with Posture and that NAM is sufficient for us.

  but when installing AnyConnect vpn module must be installed and cannot be avoided, so VPN tab is also visible in the GUI AnyConnect interface,

  I need to disable the VPN tab from the interface chart anyconnect, because it is not used and confusing for end users.

  We have anyconnect-win-4.1.00028-pre-deploy-k9.

  We have a manual installation of AnyConnect on PC or Client Provisioning, we don't use MSI

  Please suggest 'VPN profile' to end users, which will hide this vpn module.

  Thank you

  Ahad

  Your situation is highlighted in the AnyConnect Administrator's Guide as well:

  When you configure the object Configuration AnyConnect to ISE, unchecking the VPN module under the AnyConnect Module selection does not disable VPN on the customer deployed/put in service. You must set VPNDisable_ServiceProfile.xml to disable the VPN AnyConnect GUI tile. VPNDisable_ServiceProfile.xml is on EAC with other files AnyConnect.

  The xml file, you need should be on the AnyConnect downloads page, but is not. There's a BugID noting that (CSCus26084). Work around the BugID does not work for me, but it could for you.

  The profile CAN be found in the msi file - if you open with 7-zip, you can find the file. She is short, so I'll just paste here:

       true