router wag200G as switch only?

Similar Questions

• Inter vlan routing on a Cisco SF 300-24 port switch only no internet except when scanning with wireshark

  Hello

  I'm get inter vlan routing to work on a 300-24 ports switch DF.    I have a network of business existing on 192.168.111.0 and want to create a vlan on 192.168.1.1 which can talk to 192.168.111.0.    I activated the layer 3 routing on the switch through the console and also provided ip routing commands. I have the following VIRTUAL networks:

  Vlan1 - default 192.168.111.0

  VLAN2 - 192.168.1.0

  I turned on DNS and provided my two servers DNS 192.168.111.82 & 192.168.111.212.

  I updated the VLAN1 interface 192.168.111.217 and VLAN2 interface 192.168.1.1.

  The FE1 - FE15 ports are access ports and assigned to VLAN1 (unidentified)

  FE16 - FE24 ports are access ports and assigned to VLAN2 (unidentified)

  I put a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (router Draytek 2600). I have connected a computer (A) at the port of VLAN1 FE3 and a computer (B) to VLAN2 FE16 port.   I put its IP address and computer default gateway has to 192.168.111.217 to 192.168.111.94.    I updated computer B default gateway 192.168.1.1 and 192.168.1.2 IP.

  Computer A has access to the Mdaemon Server files via the network grows but no internet (cannot ping google) and can ping computer B and RDP on computer B.

  Computer B can ping computer A and RDP on A computer but do not have access to the company network i.e. MDaemon, file server etc.   It can also access the internet.

  The console I can ping www.google.co.uk and all the ip addresses in the network of the company i.e. 192.168.111.82 (DNS server).   I do not understand what I am doing wrong and have been banging my head for staretd a few days a new job and desperately need to work so any help would be greatly appreciated

  If I have computer scanner a wireshark wirh internet starts working wheird!

  Show the configuration below:

  switch7c0a71 #show run

  database of VLAN

  VLAN 2

  output

  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

  Add a voice vlan Yes-table 00036 b Cisco_phone___

  Add a voice vlan Yes-table 00096e Avaya___

  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

  Add a voice vlan Yes-table 00d01e Pingtel_phone___

  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

  Add a voice vlan Yes-table 00e0bb 3Com_phone___

  interface vlan 2

  IP 192.168.1.1 255.255.255.0

  output

  interface vlan 1

  IP 192.168.111.217 255.255.255.0

  output

  IP route 0.0.0.0 0.0.0.0 192.168.111.254

  interface vlan 1

  no ip address dhcp

  output

  Hello interface range vlan 1

  hostname switch7c0a71

  No complexity of passwords allow

  No server snmp Server

  interface fastethernet1

  switchport mode access

  output

  interface fastethernet2

  switchport mode access

  output

  interface fastethernet3

  switchport mode access

  output

  interface fastethernet4

  switchport mode access

  output

  interface fastethernet5

  switchport mode access

  output

  fastethernet6 interface

  switchport mode access

  output

  interface fastethernet7

  switchport mode access

  output

  interface fastethernet8

  switchport mode access

  output

  interface fastethernet9

  switchport mode access

  output

  interface fastethernet10

  switchport mode access

  output

  interface fastethernet11

  switchport mode access

  output

  interface fastethernet12

  switchport mode access

  output

  interface fastethernet13

  switchport mode access

  output

  interface fastethernet14

  switchport mode access

  output

  interface fastethernet15

  switchport mode access

  output

  interface fastethernet16

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet17

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet18

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet19

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet20

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet21

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet22

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet23

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface fastethernet24

  switchport mode general

  VLAN allowed switchport General add 2 unidentified

  output

  interface vlan 2

  name of development

  output

  Hi Richard,

  43 - permit Protocol: any / all

  42 - Protocol deny EVERYTHING 192.168.2.0 0.0.0.255-> to 192.168.111.0 0.0.0.255

  41 - Protocol to deny ALL 192.168.111.0 0.0.0.255-> to 192.168.2.0 0.0.0.255

  40 allow the RDP Protocol TO ALL

  etc.

  To block everything, including MSSQL, with the exception of the RDP and other ports that you defined above.  The other defined are simply not the RDP Protocol and service work?

  Richard, do note useful messages and identify the right answers.

  Best,

  David

• Defining a router and 2 switches in a network

  Hello!

  I have a question, please reply as soon as possbile.

  Look, I'm new in routing, just lerning, CCNA Discovery course, there is the problem:

  

  well, I'll put in place a ROUTER and 2 switches, I have set up in terminal:
  the end result, we have:
  ETH 0/0 (from where internet is coming) - IP - 192.168.100.200
  ETH 0/1 (inside the network) - IP - 192.168.80.1

  Also, I configured the same way ARP:
  Slash rip router (config) #.
  slash network (config - router) # 192.168.100.0 / / IF I understand ARP allows data transffer beetween networks and make it visible on the other

  slash network (config - router) # 192.168.80.0

  now, if the two devices end network (PC), I ping the ping works and the package was sent and received.
  !!!! THE PROBLEM IS > why I can't ping (PC0) 192.168.100.201 the 192.168.80.2 (PC1)
  the INVESTIGATION period was made.

  There are in tie my tracert schema package. Thx for the reply and attention!

  you have the default gateway configured on the two PCs?

• configuration of VLAN and routing problem 6224 switch

  I, m having a problem accessing internet to vlan 10. I can ping everything of all the VLANS. My internet router/firewall is on ethernet 1/g11 and has an ip address of 192.168.5.254. I have no problem accessing internet to vlan 20. I add a static route to my router/firewall. What Miss me? This is my first configure a layer 3 switch.

  Configure
  database of VLAN
  VLAN 10.20
  output
  battery
  1 1 member
  output
  IP 10.10.10.1 255.255.255.0
  default IP gateway - 10.10.10.254
  IP routing
  IP route 0.0.0.0 0.0.0.0 192.168.5.254
  interface vlan 10
  Routing
  IP 192.168.100.1 address 255.255.255.0
  output
  interface vlan 20
  Routing

  192.168.5.1 IP address 255.255.255.0
  output

  !
  interface ethernet 1/g1
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g2
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g11
  switchport mode general
  switchport General pvid 20

  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g12
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g13
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  output

  Route ip console #show

  The traffic code: R - RIP derived, O - OSPF derived, C - connected, S - static
  B - BGP derived, IA - OSPF Inter zone
  E1 - OSPF external Type 1, E2 - OSPF external Type 2
  N1 - OSPF NSSA external Type 1, N2 - OSPF NSSA external Type 2

  S 0.0.0.0/0 [1/0] via 192.168.5.254, vlan 20
  C 192.168.5.0/24 [0/0], directly connected, vlan 20
  192.168.100.0/24 C [0/0], directly connected, vlan 10

  Console #.

  
  

• I got alltel for internet and had to get a craddlepoint router now since switching to ellementmobile I had to get a gateway router cdw530am mdl, but it won't work on my computer at home?

  I had alltell for my internet and had to get a craddelpoint router so I could use my home computer and laptop at the same time, but given that the switch to mobile really, I had to get a combo wifi broadband gateway mdl cdw530am, but now my home computer does not connect to the router , but the laptop with no promblem has anyone else had this problem?     any help would be greatly appreciatted!

  Install the drivers for your new device

  Good luck!

• Linksys BEFSX41 wired router - fixation using OpenDNS only

  Question: I want to configure wired Linksys BEFSX41 router so that clients must use OpenDNS.  I've already implemented the DNS1 and DNS2 with appropriate OpenDNS ip addresses. 208.67.222.222 and 208.67.220.220

  Basically, the requirement must allow the OpenDNS DNS server above addresses and refuse all other DNS server addresses. Is it possible to configure the router to do this or should I find another solution?

  Thank you

  N ° the BEF does not have a CLI. You can only configure it through the web interface. And there is no option to configure something like this.

• Routing between a router and a switch L3

  Hi I have a question where I have two sites we try to connect through an ethernet port. In site 2, I use the port of gig0/0 on router 1941 and configured the port as such:

  interface gig0/0

  IP 192.168.18.2 255.255.255.252

  IP route 10.0.4.0 255.255.255.0 192.168.18.1

  site 2, I use a switch 3750 because I have no port available on their router together and is configured as such:

  interface FastEthernet4/0/1

  No switchport

  IP 192.168.18.1 255.255.255.252

  IP route 172.20.0.0 255.255.0.0 192.168.18.2

  Although the two ports appear as more and I can ping their interfaces locally, I can not ping interfaces aside until now neither their networks.

  I tried changed the front door of the local interface, but that does not work either.

  The carrier claims that I must have on one vlan and suggested this config on site 1:

  Interface gig0/0,955

  encapsulation dot1q 955

  IP 192.168.18.2 address 255.255.252

  And there is the problem.  I can not configure a subinterface on the L3 switch and cannot add the vlan as they recommend.

  Any suggestions from anyone on how to connect the two sites?

  Thank you

  Pete

  The real port must be configured as a trunk because of the end of the router. If so -.

  (1) create a vlan 995

  (2) configure the port as trunk but don't allow that vlan 995 on it

  (3) create IVR and IP migration

  Jon

• WRVS4400N serving gig switch only

  I have 2 WRVS4400N availible be. It runs my network and security connected to my WAN.

  I want to use another one strictly as a switch or even add reason for my current wireless network wireless.

  Is this possible and if so someone can give me the direction as to what I should do. Thank you, Rob

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  You won't be able to use it as a wireless Repeater. However, you can run either as a switch.

  First of all,

  Disable DHCP on this device and change mode to router mode gateway device. Then connect a cable between your router LAN port to a LAN port on the one that you are wanting to use a switch.

  Now at this point if you want to use the unit as a second access point, you can set your SSID and security as well.

  It was just a brief highlight on how to do it. I may have missed a few minor details.

  If you need, please call in the support center and someone can also help you with this configuration.

  Thank you

  Eric Moyers

  Support of Cisco network engineer

  SME HWC Wireless and monitoring

  CCNA, CCNA-wireless

  1-866-606-1866

• problem with power switch only works a 'cold' start after pushing several times.

  Original title: power switch problem

  The power switch on my computer doesn't work as a 'cold' start after pushing several times.
  Could I have accidentally re-set one "true or false? spend in the registry while trying to solve another problem?
  Dave

  Hello

  Looks like that the power switch has developed a problem, probably about to fail.

  Whatever settings are they should be consistent and not need to several tests.

  Check with a real computer store (the one that makes its own internal and no service
  leeks and glances at a Best Buy or other stores) or system manufacturer support
  (for systems custom Integrator system and the manufacturer in the case of construction of House).

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I can run router WRT160N wireless switch wireless E900

  Recently the range of my Ipad has declined. So I bought an E900 to suplement my WRT160N (2 areas served by two different wireless).

  My question is can I connect my modem cable in the E900 and have both the wireless on this work and feed the WRT160N via a wired connection so that the WRT160N can also act as a wireless router?

  If so what needs to be done as I tried to connect them without the Linksys E-series installation CD and it did not work (surprise ;-()

  JB

  Sure here ya go.

  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&login=1&app=search&VW=1&articleid=3733

• DateTime liquid switch only works on some browser form input fields

  I have a form of agreement where I would like to have the current date is displayed only (readonly) in the form of entry.  This will display the date perfectly well a range of browsers and OS but my client always reports that the form field displays the date + time (22-June-2015-12:00). Apparently, it still shows 12:00 for the time. I was unable to reproduce it in any of my tests with several browsers and operating systems.

  That's what I wrote to add the date:

  {% assign dateVariable = {{globals.site.dateNow | date}} %}}

  < b >

  < td >

  < label for = "CAT_Custom_19994415" > Date of acceptance < span class = "req" > * </span > < / label > < br >

  < input type = "text" name = "CAT_Custom_19994415" id = "CAT_Custom_19994415" class = "cat_textbox" readonly = "readonly" = value "{{dateVariable |}}" {{date: '%d - MMMM-yyyy'-}} ">"

  < table >

  < /tr >

  Must I add another filter to indicate to the server does not add a time in there? Or maybe add some Javascript for him say look for a while and remove it?

  Any help would be much appreciated.

  It's weird.

  It will not be something to do with the browser because liquid is script server-side and today's date is server only side not the client side too.

  | date displays only the date but not the time, and I did not add time.

  I do not notice on your input field you after the aaaa: a dashboard - that needs to go just in case where but I don't think it would be. You need javascript.

  Remote connect to your computer for customers to watch what they see, never take a customer what they say on face value.

• Need router and switches for simple network tips...

  I have to get a new router and switch to an office with 9 computers, 1 printer, and a server.  They are all Mac computers. Two Mac computers are running Windows XP through Parrallels (not sure if it matters).  All computers have just need access to the Internet (through the router), access to the printer and 5 of them on the server.  A few more important details: the router will be located about a quarter of a mile away (where we could get a broadband Internet access) but will have a fiber optic cable running to the office, where will be the selector. In the building off site where the router, we would like to have a backup disk to send important files at the end of each day (or set up to do this automatically later).  The optical fiber has capacity of the card.  We want that the router must be connected only (wireless).  Any suggestion that router and switch combo would be enough?  Thank you!

  You can use a RVS4400 router that has a gigabit capacity with 4 ports, connected to the gigabit switch.

• NAT router 1841 and 3550 switch help

  Hi experts, I need some help with setting up a network.  Network diagram is attached.

  I created 3 VLANs on the 3550 Switch and activated InterVLAN Routing.  I can't do a ping from one VLAN to another.  I've added static routes to networks VLAN on the router.  Is the only part I'm not sure where and how configure NAT?  For example, if it was just a standalone router Cisco 1841 I would just create list of access and NAT FA 0/0 outside and FA 0/1 on the inside.  It would be great if someone can give me an example or point me to the right direction.

  Router ISP--> Cisco 1841--> Switch Cisco 3550

  Cisco 1841 router:

  FA 0 / 0--> WAN Interface

  IP address: 30.20.10.2

  FA0 / 1 Interface LAN connected to the 3550 switch-->

  IP address: 10.0.0.1/24

  Cisco 3550 switch:

  FA 0 / 24--> to connect to the Cisco 1841 router

  IP address--> 10.0.0.2/24

  FA 0/1 - 0 / 10--> VLAN 1

  FA 0/11 - 0 / 20--> VLAN 2

  FA 21/0 - 0 / 23--> VLAN3

  Thank you

  Hello, it's the same thing, but in your access list, you need allow all of your internal address ranges. On your router and 3550 make sure routing everything is OK, you say you have connectivity.

  This means that your network 10 should be able to get to your 192 networks and vice versa.

  On your 3550, you can have a default route to the router. And your router should have roads to 192 networks via the address 10 of the 3550.

  Then the NAT configuration

  Int fa0/1
  IP NAT inside

  Int fa0/0
  NAT outside IP

  IP access-list standard MYNAT
  Permit 10.0.0.0 0.0.0.255
  Permit 192.168.1.0 0.0.0.255
  Permit 192.168.2.0 0.0.0.255
  Permit 192.168.3.0 0.0.0.255

  And then in your NAT statement

  IP NAT inside source list MYNAT interface fa0/0 overload

  Hope this helps

  Sent by Cisco Support technique iPhone App

• Routing to the unauthorized via switch Ethernet HP 1910 169.254.0.0/16 subnet

  Hello

  I have a somewhat unusual situation at a customer site. They have an HP 1910 as a default gateway on their local network Ethernet switch. This is related to a Fortigate Firewall with a regular DSL connection and a WAN link to emote subnets. The question we have is that a new remote site has become active on the Wan. The unusual thing is that they have a 169.254.0.0/16 subnet. Don't ask me why this address range has been used but it is there. (169.254.0.0/16 is a space of address reserved for windows clients that cannot receive an IP via DHCP)

  The client is when they try and access a resource on 169.254.0.0/16 through the switch and on the Wan of the HP 1910 switch removes the packages and will not pass them. I have trioed add static routes on the switch, but it does not transmit packets 169.254.0.0/16. Al, the other traffic is very well. Has anyone ever encountered this weird behavior?

  I think I knew the people. Article 2.7 of the RFC section https://tools.ietf.org/html/rfc3927 which States that to 169.254.0.0/16 packages be sent to layer 3.

  Do not know why some devices transmit these packets, but it seems that best practices is for devices of L3 to drop packets that have 169.254.0.0/16 in their source/destination IP address fields.

• How is the best way to connect the configuration of my router and switch?

  I have a cable modem. connect to a switch, I have 2 computers connected to the switch. I also just connected my router wireless switch. That's the best configuration or I lose my firewall of the router in passing is not by ports directly above?

  Most of the cable modems will give an IP address, so connect a switch to the modem and then connection of two computers and a router to the switch will usually result in one of these three devices, get an IP address (and internet connection), while the other two will not be.  (Notice that I guess a true "Modem" and not a "Modem/Router" device).  The correct configuration would be to connect your router to the modem (router gets the unique IP address).  The router can then process from the addresses IP what either side LAN of the router, then plug the devices you need (including switch) to the router's LAN ports.  This also ensures that all devices will be on the same subnet that your connection scheme to separate devices on the router wireless from the other two devices on the switch (here, assuming that you have a router/Modem device).

  HTH,

  JW