RV042 several subnets

I have a race RV042 firmware more recent and I would

know if the following is possible:

I would like to have two subnets 192.168.1.0/24 and 192.168.2.0/24

I would like to have DHCP available on both, with some static DHCP assignments on both.

I would like to have each subnet assigned to a port on the back of the router.

Example:

You plug a laptop 1 Port, and you get an address like 192.168.1.xxx

You plug a laptop Port 2, and you get an address like 192.168.2.xxx

How I would make this happen?

Hi Matt,

RV0XX routers support only port based VLAN. Multiple subnet feature allows the different subnet router to understand and communicate with them. The DHCP server can be configured to 1 single subnet. This goal would require an external DHCP service.

If you are looking for this feature as described, you can look in the router RV180.

-Tom

Tags: Cisco Support

Similar Questions

Several subnets in the site to Site VPN

Hi guys,.
I would like to set up a site of tunnel VPN stie with several subnets. I could not find a configuration which is my problem. I hope you can help me with the solution.
You can find my design network attach to this subject.
This is my setup on the ASA:

(1) NAT excemption for network traffic, go to the Site to site VPN.
NAT (MGMTLAN, INT STSVPN) static source 192.168.10.0 192.168.10.0 static destination 192.168.31.0 192.168.31.0
NAT (inside, INT STSVPN) static source 192.168.15.0 192.168.15.0 static destination 192.168.38.0 192.168.38.0

(2) the Accesslist with traffic to encrypt
object-group network 192.168.10.0
object-network 192.168.10.0 255.255.255.0

object-group network 192.168.15.0
object-network 192.168.15.0 255.255.255.0

the 192.168.38.0 object-group network
object-network 192.168.38.0 255.255.255.0

the 192.168.31.0 object-group network
object-network 192.168.31.0 255.255.255.0

object-group network STSVPN-LOCAL
Group-object 192.168.10.0
purpose of group - 192.168.15.0

object-group network STSVPN-US
purpose of group - 192.168.38.0
purpose of group - 192.168.31.0

ACL_STSVPN-US allowed extended ip access-list object-STSVPN-LOCAL object group STSVPN-American

(3) proposal phase 1
IKEv2 crypto policy 10
aes-256 encryption
sha256 integrity
Group 14
FRP sha256
second life 86400

(4) proposal phase 2
Crypto ipsec ikev2 proposal ipsec IKEV2-IPSEC-ESP-AES-SHA
Protocol esp encryption aes-256
Protocol esp integrity sha-256

(5) group tunnel
tunnel-group 4.4.4.4 type ipsec-l2l
tunnel-group 4.4.4.4 General attributes
Group Policy - by default-GrpPolicy-STSVPN-US
IPSec-attributes tunnel-group 14.4.4.4
IKEv2 remote-authentication pre-shared key abcd
IKEv2 authentication local pre-shared key abcd

GroupPolicy
Group Policy GrpPolicy-STSVPN-US internal
Group Policy attributes GrpPolicy-STSVPN-US
value of VPN-filter STSVPN-US
Ikev2 VPN-tunnel-Protocol

(5) crypto card
10 CM-STSVPN crypto card matches the address STSVPN-US
10 CM - STSVPN peer set 4.4.4.4 crypto card
card crypto 10 CM-STSVPN set ikev2 proposal ipsec IKEV2-IPSEC-ESP-AES-SHA
interface card crypto INT-STSVPN CM-STSVPN
Crypto ikev2 enable INT-STSVPN

/////////////////////////////////////////////////////////////////////

The router configuration:

(1) part SA

proposal of crypto ikev2 ki2. PROP
encryption aes-cbc-256
sha256 integrity
Group 14
IKEv2 crypto policy ki2. POL
proposal ki2. PROP
ikev2 KR1 encryption keys
peer ASALAB
address 2.2.2.2
pre-shared key local abcd
pre-shared key remote abcd
Profile of crypto ikev2 ki2. TEACHER
match one address remote identity 2.2.2.2 255.255.255.255
address local identity 4.4.4.4
sharing front of remote authentication
sharing of local meadow of authentication
door-key local KR1

(2) Transformset

Crypto ipsec transform-set TS. VPN2, esp esp - aes hmac-sha256-256
tunnel mode

(3) access-list

IP ACL extended access list. VPNIKE2
IP 192.168.31.0 allow 0.0.0.255 192.168.10.0 0.0.0.255
IP 192.168.38.0 allow 0.0.0.255 192.168.15.0 0.0.0.255

(5) crypto card

crypto CM card. 30 VPN ipsec-isakmp
defined peer 2.2.2.2
the transform-set TS value. VPN2
group14 Set pfs
ki2 ikev2-profile value. TEACHER
match address ACL. VPNIKE2

//////////////////////////////////////////////////////////////////////

This configuration is correct to allow both subnets on each side of the VPN tunnel to communicate with each other.

192.168.31.0 subnet cannot communicate with 192.168.10.0
192.168.38.0 subnet cannot communicate with 192.168.15.0

Hello Jay,

I went during the configuration of the two aircraft and noticed a few errors on the configuration of the SAA. Details here:

(1) the access list configured for VPN traffic is named ACL_STSVPN-US, however the address for correspondence configured on the map encryption uses a group of objects name instead:

address for correspondence card crypto 10 CM - STSVPN STSVPN-US

You must change this setting to avoid any problems with the negotiation of traffic:

no matching address card crypto 10 CM-STSVPN STSVPN-US

10 CM-STSVPN crypto card matches the address ACL_STSVPN-US

(2) you also have the same error on the configured vpn filter. However, you could not use the access list ACL_STSVPN-United States for VPN filter since the ASA will filter incoming packets only. In this case the appropriate ACL will be configured for remote network (ROUTER) to local networks (ASA). It will look something like this:

access-list VPN_filter extended permitted ip object-STSVPN-US group LOCAL STSVPN

access-list VPN_filter extended permitted ip object-STSVPN-US group LOCAL STSVPN

Group Policy attributes GrpPolicy-STSVPN-US
VPN-Filter VPN_filter value

Keep in mind that the VPN filter is in the rules that determine whether to allow or deny packets of data tunnelees coming through the device security, based on criteria such as the source, destination, and Protocol address address. If you want to use the IP Protocol, the filter will not make a difference.

(3) group 14 of the PFS is configured on the router crypto map, but not on the SAA. You need to even add it in the card encryption ASA or remove it from the router.

ASA:

card crypto 10 CM-STSVPN set group14 pfs

Router:

crypto CM card. 30 VPN ipsec-isakmp

No group14 set pfs

Hope this help you to raise the tunnel,

Luis.

several subnets by VLANS and ports link

Hello
I need some clarification.
Our iSCSI SAN storage (Dell MD3660i0 requires a separate subnet by port.
We require paths multiple access and balancing in VMware.
To achieve this in ESXi 5.1 we need binding ports... BUT the binding of ports is supported only if the vmks are all in the SAME domain in accordance with these two KBs broadcasting
VMware KB: Considerations for use binding software iSCSI ports in ESX/ESXi
VMware KB: When the use of several VMkernel ports with port required to access the storage of two or more tables on different br...
OK... probably so I simply put my all subnets in ISCSI storage in one VLAN and everything will be ok (one VLAN is after all a broadcast domain, both are stuff of L2)... This would respond to the requirements of KBs... If VMware means "area of distribution" in the true sense of the term.
So my question is can you configure the port in this way binding? It is supported by VMware?

VMware has come back to me (in fact the author of one of the kb/s I've referenced)

http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2038869

He confirmed that the terminology used in the KB is misleading and "broadcast domain", it actually means "subnet" so not layer 3 layer 2.

This means that you can NOT have multiple subnets in a broadcast domain (VLAN) AND use the SW iSCSI port binding.

BUT

He told me (he is very familiar with the Dell MD3660i iSCSI kit), you don't have to have binding of ports to achieve several Multipathing and load balancing. If you have a requirement for several subnets of your iSCSI SAN provider then just create multiple vmks on different subnets, and DO NOT make the port binding. The fact that they are on different subnets will be enough to achieve the multiple paths

It updates the KB to make this much clearer.

I hope this helps someone

RV042G and several subnets

Hi!, I am trying to configure a RV042G to process at least 3 subnets, I see that it does not support 802. 1 q trunks, but on the interface of configuration page it gives the possibility to define a vlan for the port (static options: vlan1 vlan4 :/) but it is not possible to address IP Configuration for each vlan.)

How is it?, is a router that cannot route between subnets?, what are the VLAN used for then?

Kind regards.

Ciro,

Please see the following thread. This might give you a better idea of the functioning of the RV042 (G) about the VLAN and multiple subnets.

https://supportforums.Cisco.com/thread/2226281

-Marty

VPN Tunnel access to several subnets ASA 5505

Greetings,

We spent a little time trying to configure our ASA 5505 in order to TUNNEL into several different subnets. Subnets include 192.168.1.0 / 192.168.2.0 / 192.168.10.0

Someone is about to review this setup running and indicate where we have gone wrong. When I connect via the VPN Client, I can access the 192.168.1.0 network, no problem. But fail to reach the other two. Thank you very much.

Output from the command: 'show running-config '.

: Saved

:

ASA Version 8.2 (5)

!

hostname BakerLofts

activate kn7RHw13Elw2W2eU encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

switchport access vlan 12

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.1.254 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP 74.204.54.4 255.255.255.248

!

interface Vlan12

nameif Inside2

security-level 100

IP address 192.168.10.254 255.255.255.0

!

passive FTP mode

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

vpn_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

outside_access_in of access allowed any ip an extended list

inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.3.0 255.255.255.0

Inside2_access_in of access allowed any ip an extended list

permit Inside2_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.3.0 255.255.255.0

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

MTU 1500 Inside2

IP local pool vpn 192.168.3.1 - 192.168.3.254 mask 255.255.255.0

no failover

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

NAT (outside) 0 192.168.3.0 255.255.255.0 outside

NAT (Inside2) 0-list of access Inside2_nat0_outbound

NAT (Inside2) 1 0.0.0.0 0.0.0.0

Access-group outside_access_in in interface outside

Access-group Inside2_access_in in the interface Inside2

Route outside 0.0.0.0 0.0.0.0 74.204.54.1 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

AAA authentication enable LOCAL console

AAA authentication LOCAL telnet console

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

Crypto ca certificate chain _SmartCallHome_ServerCA

certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130

010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a

30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b

13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504

0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72

20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269

65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d

65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31

30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b

30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20

496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65

74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332

68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329

302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f

63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d

010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597

a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10

9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc

7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b

15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845

1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd

18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced

4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f

81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201

082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868

7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101

ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff

45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777

2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a

1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406

03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973

69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403

02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1

6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b

c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973

69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30

1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603

445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04

1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d

2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101

4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e

b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a

99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018

481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16

b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0

5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8

6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28

6c2527b9 deb78458 c61f381e a4c4cb66

quit smoking

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet 192.168.1.0 255.255.255.0 inside

Telnet timeout 5

SSH timeout 5

Console timeout 0

dhcpd outside auto_config

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal vpn group policy

attributes of vpn group policy

value of server DNS 8.8.8.8

Protocol-tunnel-VPN IPSec

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list vpn_splitTunnelAcl

username, password samn aXJbUl92B77AGcc. encrypted privilege 0

samn attributes username

Strategy-Group-VPN vpn

username password encrypted QUe2MihLFbj2.Iw0 privilege 0 jmulwa

username jmulwa attributes

Strategy-Group-VPN vpn

jangus Uixpk4uuyEDOu9eu username encrypted password

username jangus attributes

Strategy-Group-VPN vpn

vpn tunnel-group type remote access

VPN tunnel-group general attributes

vpn address pool

Group Policy - by default-vpn

Tunnel vpn ipsec-attributes group

pre-shared key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

anonymous reporting remote call

Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e

: end

I see two problems:

1. your ASA has not an interior road to the Incas inside networks. You must add:

Route inside 192.168.2.0 255.255.255.0

Route inside 192.168.10.0 255.255.255.0

.. .specifying your gateway address of these networks.

2. the statement "access-list standard vpn_splitTunnelAcl permit 192.168.1.0 255.255.255.0" sends only a route for 192.168.1.0/24 to your customer. You need to add entries for the other two networks.

several subnets to my vm

With limits of the vswitches, how most of the people there set up several virtual machines, where half can be used on a subnet and the other half on another subnet.
For example:
VM1 is on 192.168.1.1
VM2 is 192.168.5.1
ESXi 4.1 using
Physical Layer 3 switches with multiple subnets and gateways

With the switches you mention, I configure the VLAN (if not already done), configure the physical ports like port junction and make the VLAN tagging on the groups of virtual ports. In this way, you can use a vSwitch with 2 (or more) groups of ports, each with the VLAN you need. See VST (virtual switch tagging) in http://www.vmware.com/files/pdf/virtual_networking_concepts.pdf

André

Several subnets on a WAN interface

We have a WAN connection that Comcast provides us with two different subnets. Currently, the interface is programmed with just the static IP address.

How can I enter the subnet on which has our static range of IP addresses? I saw this article, but I don't know if that's what I have to do.

Help!

Yes, you have found the right article.

I need VPN gateway to gateway with NAT for several subnets, RV082

I have a pair of RV082 routers and I would like to configure a gateway to gateway VPN tunnel, as described in a book, "How to configure a VPN tunnel that routes all traffic to the remote gateway," (name of file Small_business_router_tunnel_Branch_to_Main.doc). I followed this recipe book and found that my while the main office has internet connectivity, the branch subnet is not an internet connection.

Routing behaves as advertised, where all traffic goes to the seat. However, the 192.168.1.0 subnet in the branch receives no internet connectivity. I read in other posts that the main router will provide only NAT for the local subnet, not the Management Office subnet. Is it possible to configure the RV082 router to provide NAT for all subnets?

If this is not the case, what product Cisco will provide connectivity VPN Tunnel as well as the NAT for all subnets? The RV082 can be used as part of the final solution or are my RV082s a wasted expense?

Here is the configuration that I had put in place, (real IP and IKE keys are false).

Bridge to bridge

Remote Head Office

Add a new Tunnel

No de tunnel 1 2

Name of the tunnel:, n1 n1-2122012_n2-1282012-2122012_n2-1282012

Interface: WAN1 WAN1

Enable : yes yes

--------------------------------------------------------------------------------

Configuration of local groups

Type of local security gateway: IP only IP only

IP address: 10.10.10.123 10.10.10.50

Local security group type: subnet subnet

IP address: 192.168.1.0 0.0.0.0

Subnet mask: 255.255.255.0 0.0.0.0

--------------------------------------------------------------------------------

Configuration of the remote control groups

Remote security gateway type: IP only IP only

IP address: 65.182.226.50 67.22.242.123

Security remote control unit Type: subnet subnet

IP address: 0.0.0.0 192.168.1.0

Subnet mask: 0.0.0.0 255.255.255.0

--------------------------------------------------------------------------------

IPSec configuration

Input mode: IKE with preshared key IKE with preshared key

Group of the phase 1 of DH: Group 5 - 1536 bit group 5 - 1536 bit

Encryption of the phase 1: of THE

The phase 1 authentication: MD5 MD5

Step 1 time in HIS life: 2800 2800 seconds

Perfect Forward Secrecy: Yes Yes

Group of the phase 2 DH: Group 5 - 1536 bit group 5 - 1536 bit

Encryption of the phase 2: of THE

Phase 2 of authentication: MD5 MD5

Time of the phase 2 of HIS life: 3600 seconds 3600 seconds

Preshared key: MyKey MYKey

Minimum complexity of pre-shared key: Enable Yes Enable

--------------------------------------------------------------------------------

If you are running 4.x firmware on your RV082, you must add an additional Allow access rule for the Branch Office subnet (considered one of the multiple subnets in the main office) may have access to the internet. Note the firmware version has more details about it.

http://www.Cisco.com/en/us/docs/routers/CSBR/rv0xx/release/rv0xx_rn_v4-1-1-01.PDF

Several subnets on a single NETWORK adapter

I have two subnets, I want to be able to use with my virtual machines on a server with 5.5 ESXi. I have only a single NETWORK adapter that is available on the host.
The VMkernel default Port, vmk0 is assigned the IP 10.208.82.34/29. The default gateway is 10.208.82.33. Can I add virtual network adapters to virtual machines and the ping without problem to a host outside the subnet 10.208.82.32/29.
I created a second Port VMkernel, vmk1 and assigned the IP 10.108.65.38. Then, I set up a second virtual NETWORK adapter inside a virtual machine with an IP address of 10.108.65.33. I can't ping this new IP address, 10.108.65.33, to another host. However, I can ping 10.108.65.38 without any problem. If adding a second card virtual NETWORK to a different virtual machine and assign it 10.108.65.34, I thing ping 10.108.65.33 without any problem. I cannot ping this address, 10.108.65.34, another host either.
I know that the issue is not routing as doing a traceroute from a host shows the correct path is taken. determination of route of 10.108.65.38 complete normally. I don't have access to the network infrastructure, because it is a server in a data center.
The VMkernel, vmk1, using the 10.108.65.38, is accessible from the default gateway and the other hosts in the data center. However when I attribute 10.108.65.33 to a virtual machine, I can't reach that what anyone outside the 10.108.65.32/29 network, which is my problem right now. If I assign an address in the subnet of 10.108.65.32/29 as the single IP address to a virtual computer, it still does not work is not a problem of routing within the virtual machine.
I feel as if I had something simple here as it seems to work almost disappeared.

Here is the configuration of the network:
This is the routing table:
~ # esxcfg - road - l
VMkernel itineraries:
Interface of network gateway subnet mask
10.108.65.32 255.255.255.248 subnet local vmk1
10.208.82.32 255.255.255.248 subnet local vmk0
by default 0.0.0.0 10.208.82.33 vmk0

I ended up having the point of provider the subnet 10.108.65.32/29 to their router or switch to 10.208.82.38, I have basic and then install a Linux router with iptables to route traffic to myself.

Linked clones and several subnets / VLAN

Hey all,.
In an environment with thousands of VMS, there at - it a better practical method to deal with the fact that some of the clones will be on different subnets or VLANS?
For example, imagine 500 clients need to be on a separate network other clones.
- Creation of another master VM model would cause more costs general administrative (maintenance of multiple masters)
- Manually move the special 500 VMS to their own network would be ok, but it would be lost during a refresh/rebuild because the master is always on the main network.
From what I've read so far, the best thing to do is a powershell script to change the special virtual machine VIRTUAL LAN after each refresh/redial.
I wanted to ask you, if there was a best practice for this problem in large environments.
Thank you
Drew

I think that it is an area where the view really fails and should probably be a feature request for future versions. I didn't know the established practice of the best, but I would probably lean towards the powershell script to make the changes as the easiest to maintain and operate.

Several subnets on a NETWORK adapter with BladeCenter?

We have an IBM BladeCenter H chassis with switches Cisco 3012. Each blade server is configured with a total of 4-port NETWORK adapter. Our initial intention was to 2 4 network cards for the traffic of the virtual machine and the others, two for tolerance to the failures/vmotion/management team. It has recently been brought to my attention that there is another necessary subnet for some of the virtual machines that will run on these servers. So, my question is, can I have access to multiple networks (10.1.1.x & 192.168.0.x) through two NICs servile mentioned above to the traffic of VMware? Keep in mind it's bladecenter environment, I have the external ports on the back of the chassis of the physical connectivity. All documentation showing this would be the icing on the cake. Thanks in advance.

You should be able to this with trunking and tagging of vlan. This will allow you to pass the traffic of multiple VLANs and label it.

Jason Silva

http://silvaecs.com

http://Twitter.com/silvaecs

Cisco WLC SSID anchored several subnets

Hello

I have a requirement to land a SSID on a controller of the anchor but that AP customer connect I need them to receive certain IP address.

Then...

I have a LWAP called AP1 connection to WLC1, WLC1 uses WLC2 as the anchor for the ssid SSID1 DC. When a user connects, I want the user to get an address of SUBNET1. If a user connects to AP2 is also linked to the WLC1 I want the user to get an address of SUBNET2

Now... If the AP is it is located directly on the WLC2 I could use groups AP to provide this feature, no one knows if its possible to combine it with anchor?

Thank you

RG

Fix... You can't do what you are trying to accomplish. If you were doing 802. 1 x, you can use override AAA to assign users to a vlan, but other than that, the WLC cannot perform this task.

Sent from my iPhone

PIX of VPN in several subnets

We have two remote sites and a framework to our parent company

the tunnel works very well between us and our remote offices, but they cannot connect to the internet application server and oracle on the parent through site framework

I have roads on our internal to the remote site router and our 520 pix for the address of the frame. How configure you routing for frame internal? 520 PIX can ping servers and network frame

set up 6.3 (3) version PIX

| Oracle application server and Intranet 173.1.2.X |

|

| Parent | net 173.1.2.0

|

|

| framework

|

| Internal router | 192.170.1.x

|

| PIX 520 our company | net 192.170.1.0

|

| External router: x.x.x.x

| |

| VPN |

| |

| PIX 501 remote sites. 192.170.2.0 and 192.170.3.0

501 sh IPSEC Security Association shows 0 for all counters

520 HS IPSEC security association

local ident (addr, mask, prot, port): DI (DI/255.255.255.0/0/0) = FRAME

Remote ident (addr, mask, prot, port): (192.170.2.0/255.255.255.0/0/0)

current_peer: X.X.X.X:0

LICENCE, flags is {origin_is_acl},

#pkts program: encrypt 0, #pkts: 0, #pkts 0 digest

#pkts decaps: 0, #pkts decrypt: 0, #pkts check 0

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, #pkts compr. has failed: 0, #pkts decompress failed: 0

#send 101, #recv errors 0

endpt local crypto. : X.X.X.X, remote Start crypto. : X.X.X.X

Path mtu 1500, fresh ipsec generals 0, media, mtu 1500

current outbound SPI: 0

SAS of the esp on arrival:

the arrival ah sas:

SAS of the CFP on arrival:

outgoing esp sas:

outgoing ah sas:

outgoing CFP sas:

520 logs shows the key request his

702303: sa_request, (ING. MSG key) src = X.X.X.X, dest = X.X.X.X, sr

DI/255.255.255.0/0/0 (type = 4) = c_proxy, dest_proxy = 192.170.2.0/255.255.255.0/0

/ 0 (type = 4), Protocol = ESP, transform = esp - esp-md5-hmac, lifedur = 28800 s a

4608000 Ko d, spi = 0x0 (0), id_conn = 0, keysize = 0, flags = 0 x 4004

It's certainly an issue access list, I'll watch this Monday. Could you please give me a printout of the

NAT (inside) 0 access - your name-list ACL.

access - your name-list ACL...

sincerely

Patrick

PIX 515 - several subnets

Can I have a 28 and one allocated 24 times in a PIX 515e? My current setup is configured for the 28 and I would like to keep this address space, just as it is and then add the 24 if possbile.

Thank you!

Hello

I think that the solution is easier than you think. You can use your new address range with nat, global and static without actually set it up on the physical interface. In this way, you can use your new address space. Your ISP should route your new network to your PIX outside interface. That's all.

Best regards

Robert Maras

ASA 5505 - several VPN subnet

I'm trying to set up a VPN for use with the Cisco VPN Client. I currently have operational VPN, but I cannot allow access to several subnets connected to the ASA. My current stock of VPN DHCP is 10.0.0.0/24. I want to VPN users to talk to one of my other VLAN (172.16.20.0/24). That's what I can't understand. If I change my VPN DHCP pool to something like 172.16.20.100 - 110 can I talk to about everything on this fine subnet. But as soon as I change the DHCP pool to the other subnet so I can't. Any suggestions?

Here is my config:

Nysyr-SBO-ASA (config) # sh run

: Saved

:

ASA Version 8.4 (1)

!

names of

!

interface Vlan1

No nameif

no level of security

no ip address

!

interface Vlan2

Description connection to the ISP (FiOS)

nameif primaryisp

security-level 0

IP address

!

interface Vlan3

Description secondary connection ISP (Time Warner)

nameif backupisp

security-level 0

IP address

!

interface Vlan5

Description Connection to the subnet internal internet access (192.168.5.0/24)

nameif inside

security-level 100

192.168.5.1 IP address 255.255.255.0

!

interface Vlan20

Description Connection to the internal management network (172.16.20.0/24)

nameif insidemgmt

security-level 100

address 172.16.20.1 IP 255.255.255.0

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

switchport access vlan 3

!

interface Ethernet0/2

switchport access vlan 5

!

interface Ethernet0/3

switchport access vlan 20

!

interface Ethernet0/4

Shutdown

!

interface Ethernet0/5

Shutdown

!

interface Ethernet0/6

Shutdown

!

interface Ethernet0/7

Shutdown

!

passive FTP mode

clock timezone IS - 5

clock to summer time EDT recurring

internal network object

192.168.5.0 subnet 255.255.255.0

network of the object asp-wss-1-tw

Home 192.168.5.11

network of the object asp-wss-1-vz

Home 192.168.5.11

network vpn-ip-pool of objects

10.0.0.0 subnet 255.255.255.0

access-list outside_access_in_1 note access list to allow outside in traffic

outside_access_in_1 list extended access permit tcp any object asp-wss-1-vz eq www

outside_access_in_1 list extended access permit tcp any object asp-wss-1-vz eq https

outside_access_in_1 list extended access permit tcp any object asp-wss-1-tw eq www

outside_access_in_1 list extended access permit tcp any object asp-wss-1-tw eq https

SBOnet_VPN_Tunnel_splitTunnelAcl standard access list allow 172.16.20.0 255.255.255.0

pager lines 24

Enable logging

asdm of logging of information

primaryisp MTU 1500

backupisp MTU 1500

Within 1500 MTU

insidemgmt MTU 1500

vpn-ip-pool 10.0.0.10 mask - 255.255.255.0 IP local pool 10.0.0.250

no failover

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

NAT (inside primaryisp) source Dynamics one interface

NAT (inside backupisp) source Dynamics one interface

!

network of the object asp-wss-1-tw

NAT (inside backupisp) static

network of the object asp-wss-1-vz

NAT (inside primaryisp) static

Access-group outside_access_in_1 in the primaryisp interface

Access-group outside_access_in_1 in the backupisp interface

Route 0.0.0.0 primaryisp 0.0.0.0 1 track 1

Route 0.0.0.0 backupisp 0.0.0.0 10

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

the ssh LOCAL console AAA authentication

Enable http server

http 192.168.5.0 255.255.255.0 inside

http 0.0.0.0 0.0.0.0 primaryisp

http 0.0.0.0 0.0.0.0 backupisp

http 0.0.0.0 0.0.0.0 insidemgmt

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

monitor SLA 123

type echo protocol ipIcmpEcho 8.8.8.8 interface primaryisp

threshold of 3000

frequency 10

Annex ALS life monitor 123 to always start-time now

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-256-SHA ikev1

primaryisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

card crypto primaryisp_map interface primaryisp

backupisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

card crypto backupisp_map interface backupisp

Crypto ca trustpoint ASDM_TrustPoint0

Terminal registration

name of the object CN =

Configure CRL

IKEv2 crypto policy 1

aes-256 encryption

integrity sha

Group 5

FRP sha

second life 86400

Crypto ikev2 enable primaryisp

Crypto ikev2 enable backupisp

Crypto ikev1 enable primaryisp

Crypto ikev1 enable backupisp

IKEv1 crypto policy 30

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

!

track 1 rtr 123 accessibility

Telnet timeout 5

SSH 0.0.0.0 0.0.0.0 primaryisp

SSH 0.0.0.0 0.0.0.0 backupisp

SSH 0.0.0.0 0.0.0.0 insidemgmt

SSH timeout 20

Console timeout 20

No vpn-addr-assign aaa

No dhcp vpn-addr-assign

a basic threat threat detection

statistical threat detection port

Statistical threat detection Protocol

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal SBOnet_VPN_Tunnel group strategy

attributes of Group Policy SBOnet_VPN_Tunnel

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelall

value of Split-tunnel-network-list SBOnet_VPN_Tunnel_splitTunnelAcl

attributes of Group Policy DfltGrpPolicy

value of Split-tunnel-network-list SBOnet_VPN_Tunnel_splitTunnelAcl

attributes global-tunnel-group DefaultRAGroup

VPN-ip-pool-pool of addresses (primaryisp)

ip vpn-pool address pool

IPSec-attributes tunnel-group DefaultRAGroup

IKEv1 pre-shared-key *.

type tunnel-group SBOnet_VPN_Tunnel remote access

attributes global-tunnel-group SBOnet_VPN_Tunnel

ip vpn-pool address pool

Group Policy - by default-SBOnet_VPN_Tunnel

IPSec-attributes tunnel-group SBOnet_VPN_Tunnel

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

Review the ip options

inspect the netbios

inspect the rsh

inspect the rtsp

inspect the skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect the tftp

inspect the sip

inspect xdmcp

inspect the icmp

!

global service-policy global_policy

context of prompt hostname

call-home

Profile of CiscoTAC-1

no active account

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory

monthly periodicals to subscribe to alert-group configuration

daily periodic subscribe to alert-group telemetry

Cryptochecksum:7a817a8679e586dc829c06582c60811d

: end

keep deleted thos lines, you don't need these lines to your remote access VPN.

Please tell me, what is the default gateway assigned on these hosts sitting on the mgmt network segment?

RV042 several subnets

Similar Questions

Maybe you are looking for