RV180 getting is not gigabit/1000 WAN port speed

Similar Questions

• Name of resource VISA get does not have USB serial ports

  We built an application on a computer that had a built-in serial port - COM1.  We have the option to change the COM port in the application.  We have installed the application built on a computer that has no serial port, but installed a USB serial Converter which records as COM3.  LabView does not see this port, even with a test application to return only the names of VISA resources.

  We have verified that the port is good with another program (a Modbus Simulator) and installed the last TIME VISA v4.41 separately without result.

  Any suggestions for more troubleshooting would be extremely useful.

  Joe T.

  My main of the application still does not work, but now the little test ones are.

  Here's what I did:

  1. update my LabView 8.5 with the last VISA - 4.4 runtime.  This update the installer as well.

  2. added the install MAX for the build.

  3. adding the Support of Configuration of NI-VISA for construction

  4. uninstalled the app and reinstalled with the new volume of the system.

  When I run MAX, COM3 appears.  He also appears in the application of test resources.  The simple test Modbus to write the program works, too.  I have a sneaky feeling that COM1 can be hardcoded somewhere in the parent application; our next task is to find where communication breaks down in our code.  The bottom line seems to be a lack of experience with the demand of our manufacturer.

  Thanks to all who participated!

  Joe T.

• Receiving the message: will not accept connections on port 7088.

  Why do I get will not accept connections on port 7088?

  Hello Thomas,.

  What you do on your computer when you receive this error message?
  What is the exact error that you are experiencing?
  Please see this link:
  http://support.Microsoft.com/kb/555375

• LAN/WAN ports not supposed to be Gigabit? Capped at 250Mbps, NOT because of the ISP LAN devices.

  Hi all

  Have a bit of a problem here. I have Internet Fiber-to-the-home (FTTH) with Bell Canada and have their Fibe Gigabit service which is 940/120 speeds up and down, respectively. I was able to bypass his combo modem/router using a switch connected to the optical network terminal (HAVE) where the fiber cable enters the House (which serves mainly my base modem) and using custom settings of VLAN and DNS in ports specific for my fiber IPTV service Bell and receivers work together through my router.

  So, I have a few routers that I tried this with to try to solve my problem. My Asus RT-AC5300 and others have no problem with having me my subscribed speed - certainly through devices connected to gigabit LAN and also via WiFi on compatible devices. But I'm not concerned about WiFi - it is specifically wired ethernet devices that are the cause. I use CAT5e and CAT6 cables only because he is a Gigabit connection. The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this? Is there something my Time Capsule prevents leave the LAN ports operating at gigabit full transfer speed? It is not only a device - I have multiple gigabit devices I tested, on all three of the TC ports, and none of them exceed 250Mbps. Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  Thanks for any ideas, comments or suggestions. Y at - it a setting I have accidentally enabled that is the cause? I had much rather use the TC of the most convenient airport for my network I was planning on getting multiple Airport extreme to position around the House to cover literally home WiFi and LAN bridges through the simple installation of these devices, but I do if I can't use my fiber subscribed speed.

  OR maybe I have a defective unit. Thanks again for the help!

  See you soon

  The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this?

  Apple AirPort routers have been designed to work with the cable standard and DSL connections.  The fiber is the new ball game, and Apple knows yet how to play the game, let alone to understand the rules.

  Most of the problems associated with connections to high speed on airports is a result of the decision of Apple to eliminate any kind of manual settings to manually adjust the speed of the WAN port on the router... and are based rather on an "Auto" setting.  Automatic adjustment seems to work pretty well on the fiber up to approximately 100 Mbps connections, but the WAN port is struggling to negotiate with high-speed connections when it is connected directly to the fiber. LAN ports can also be affected.

  Some users have reported that insert a Gigabit switch between the connection of the fiber and the Time Capsule or AirPort Extreme has helped with speeds. The theory here is that the switch can negotiate with the fiber connection much better than the WAN port on the Apple device.  If you have a handy Gigabit Ethernet switch, that it could not hurt to try this "Workaround".  Other users report no benefit when they try it.

  Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  The time Capsule is not directly connected to the fiber connection, so it OK to talk and negotiate with what he sees as a 'normal' a conventional router connection.

  Don't forget also that the 802.11ac products were designed before 2013. Current products have not changed since their introduction in June 2013.

  The bottom line... Apple needs to decide whether it wants to be an actor, or leave the routing other players company established. Such what, Apple is far behind the curve... my opinion.

  While it might not hurt to take the time Capsule to an Apple Store to check over the machine, you might want to ensure that they have in fact a fiber connection high speed to test.

• RV042 Dual WAN Port DMZ not acquire an IP from ISP

  Hello

  I am trying to replace my router with the more robust RV042 of current load balancing. Installation seems simple enough. However, I am having an issue gets an IP address of the DMZ port in load balancing mode.

  The two WAN is the same ISP and is both DSL, using the same models of DSL Modem. #1 WAN port works perfectly.

  Indeed, when an independent piece of equipment is installed in the #2 DSL modem, this gives an IP address instantly...

  The two DSL lines only require a MAC address to get their IP addresses, and none of the static values are allowed, perhaps to test only.

  The issue of intellectual property has been seen before. I can't find any reference to the iton this site.

  Thank you

  Steve

  Glad to hear that it works.

  The "save the settings and restart" is not all that rare, although it is not typical for your model.

  The obligation of power off is certainly not normal. He told me that some sort of electric lock has occurred. This could be a unique thing, caused by a discharge of static electricity, or it could indicate a manufacturing defect. If this is the first case he did re - is probably. If it is the latter, then it will need a trade at any given time.

  In any case, it seems that the MAC address index has been at least partially useful.

  Good luck, somone will be here if you need assistance once again.

• R7000 WAN Port does not use LAN as a substitute?

  I have a problem with my R7000. The WAN port is dead. I used it in access point mode for some time connected to one of my LAN ports, but I need to go back to a main router. Is it possible to run it in router mode outside of a LAN port, or I'm out of options and need to replace the router? Past the WAN port, everything works fine. Thank you!

  Ive never used Merlin, but I think you need to activate the dual WAN mode and just use the secondary interface for your main WAN while leaving the other disconnected.

• The WAN Port is communicating with the Ethernet switch?

  I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

  My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

  Thank you!

  can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

  Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

  or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

  It would be considered preferable to wiring, if it is convenient to do so.  For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

  If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

• Router Wifi Smart AC1750 cannot set the full 100 WAN port

  I connect to a static IP address.

  After putting in the IP (static IP) settings the router does not receive speeds defined by internet provider (Logix Communications).

  After consultation with Logix, told me that the WAN should be set to 'Full 100' and I could not find this setting on the device.

  From now instead of a 50mbps down I get 10 Mbps download and upload 50mbps, so I guess the current WAN settings are 'Auto' on the AC1750 router WAN and cannot be changed?

  So now I'm getting data collisions and slower than expected internet.

  I need to know if it's fixable or to return this product for refund. I've updated the firmware for more later, still no dice.

  I confirmed that my internet provider has no problem with a much older Linksys router with WAN set to 'Full 100'.
  Thank you.

  jjbraunius wrote:

  I connect to a static IP address.

  After putting in the IP (static IP) settings the router does not receive speeds defined by internet provider (Logix Communications).

  After consultation with Logix, told me that the WAN should be set to 'Full 100' and I could not find this setting on the device.

  From now instead of a 50mbps down I get 10 Mbps download and upload 50mbps, so I guess the current WAN settings are 'Auto' on the AC1750 router WAN and cannot be changed?

  So now I'm getting data collisions and slower than expected internet.

  I need to know if it's fixable or to return this product for refund. I've updated the firmware for more later, still no dice.

  I confirmed that my internet provider has no problem with a much older Linksys router with WAN set to 'Full 100'.
  Thank you.

  Just a heads-up... No domestic router vendors provide ports that you configure manually, they use all the settings of auto-negotiation. So, your ISP will have to adjust their speed of port auto, or provide you a taking router support port speed settings...

• How to get gigabit on WRT 310N speed

  I don't seem to get the gigabit speed. Router lights are blue, and the user guide should be green for gigabit.

  The router firmware is v2.0.01

  Computer model of Toshiba laptop as a505-S6015 announced as having spped gigabit

  Network card in is a Realtek PCIeFE family controller

  DSL modem is Linksys ADSLME3

  Ethernet cables from the modem router and router to the computer are the two CAT6

  My ISP provides a 3.0 MBPS speed and I measured it at this speed

  So, should I not get green lights on the router port, the power to the computer?

  Thank you

  Canadian wrote:

  Computer model of Toshiba laptop as a505-S6015 announced as having spped gigabit

  Network card in is a Realtek PCIeFE family controller

  According to Toshiba: http://laptops.toshiba.com/laptops/satellite/A500/A505-S6015

  your laptop only has a 10/100 Mbps ethernet card.

  Network map gives suggests the same thing: it is a controller PCIe FE. FE standing for "Fast Ethernet", i.e. 10/100.

  I would say that your computer is not gigabit.

• Intel Gigabit VT Quad Port Server adapt

  Hello

  I ordered two new servers: Dell PowerEdge R710 with two dual-port broadcom nic´s.

  In addition, we have installed an Intel Gigabit VT Quad Port Server Adapter.

  During the installation of the esx4 (esx 4.0.0 system update 1), card intel is not recognized by esx...

  Even after complete installation, it shows only the 4 broadcom nic´s...

  What should I do to get this card running?

  I read something on the irq sharing problems, so I disabled all the USB Ports in the BIOS, but without success.

  I also changed the pci-express slot without success :/

  Any tips? Maybe something I forgot?

  Help, please!

  Have you installed the drivers for the card when installing ESX?

  http://downloads.VMware.com/d/details/esx_esxi40_intel_82575_82576_dt/ZHcqYmR0QGpidGR3

• Cable modem has no WAN port

  I have XFinity for my cable and internet services.  We just moved into a house built in 1850 and due to the size of the House and horse hair plaster, upstairs gets very little signal WiFi.  I want to extend the reach of WiFi and intended to do with a couple of Airport extreme.  The only problem is, every tutorial I watch shows the first Airport Extreme being plugged into the WAN port on the modem cable suppliers.  My router/modem, made by Cisco, has no port Ethernet WAN port only 4.  Can I connect the Airport Extreme on port 1 and then put in place using the Airport according to normal or need a WAN port?

  If you have a modem/router, then you would connect an Ethernet cable from one of the four ports Ethernet LAN <>-... choose any you want, they are all the same... to the "O" on the AirPort Extreme WAN port.

  Then use Configuration utility of Apple AirPort "Wizard" to configure AirPort Extreme to create a wireless network that uses the same exact wireless network and the same password that the wireless Cisco uses.

  The wizard will apply automatically other correct parameters... Mode Bridge, by example... so you don't have to worry about things like that.

• Pavilion 15: HP not Pavilion no USB port works, that means UEFI diagnostic code

  All USB ports stopped working (as in no popup when it is plugged in and the devices get not power port).

  I did all the thingsm usual as uninstall drivers and re - detect.

  USB port running in UEFI test, I get the following for all three ports

  ID 0URK1V-75E89A-MFPV6J-8D4E03 FAILURE

  FAILURE IF G5FF00EA #ABU

  Searching the Web I can't find what do these codes mean someone at - it a pointers please?

  Thanks in advance

  A hardware failure in the usb on the motherboard controller chip, which means that it needs a new motherboard. Are you still under warranty?

• Can't seem to get the printer to the appropriate port to communicate with the printer Lexmark 2480.

  WndOws XP install problems with Lexmark X 2480 printer no cd

  Can't seem to get the printer to the appropriate port to communicate with the printer Lexmark 2480.  Downloaded, but prints blank pages.

  Hello, ColoChick,

  Your question must be posted in the hardware and drivers Forum.  Note the drop-down menus...

  http://answers.Microsoft.com/en-us/Windows/Forum/performance

  Search for drivers for your Lexmark printer.  The complete set is recommended for a full installation.

  http://support.Lexmark.com/index?http://support.Lexmark.com/index?locale=en&page=product&UserLocale=en_US&ProductCode=LEXMARK_X2480&focusedTab=downloads#2

  You can also try the universal print driver

  http://www1.Lexmark.com/en_US/software/UPD/index.shtml

  If possible, contact Lexmark for the installer of physical media (CD)

  Q: How can I contact the Lexmark parts?

  R: customer support is available Monday - Friday from 09:00 - 18:30 AND

  E-mail: * address email is removed from the privacy *
  Phone: 1-877-577-2787
  Fax: 1-800-258-4880

• For some reason any, that my printer has enough work and when I plug in my camera to download images, the computer says it does not recognize the USB port, which could be the pronblem?

  My printer does not work (it is said that the computer does not recognize the USB port (this also happens when I plug my camera to download the photos) I checked everything I know to check, which isn't too.)

  My printer does not work (it is said that the computer does not recognize the USB port (this also happens when I plug my camera to download the photos) I checked everything I know to check, which isn't too.)

  When did this problem start? What did you change shortly before it all began?

  Please quote the exact text of the message you get, verbatim.

• WAN port mini error 31

  WAN port mini error 31

  Hi Cooljoe613,

  I would like to gather more information about the issue.

  ؠ What edition of vista are you helping?

  ؠ Is your computer connected to a domain or a workgroup?

  ؠ How do you get this error?

  ؠ you make changes to the computer?

  If your computer is on a domain please visit the link http://social.technet.microsoft.com/Forums/en-US/category/windowsvistaitpro

  Thank you and best regards,

  Bindu S - MICROSOFT SUPPORT
  Visit our Microsoft answers feedback Forum and let us know what you think.