Sansa Clip + starts charging fully charged once more again

My Sansa Clip + has been completely cut and I plug it into the computer to charge it.

He has been in charge for about 3 hours and the animated indicator said he was almost completely reloaded. I take a quick shower and when I came back, I noticed that the trial load has been started again. The indicator shows u completely discharged battery and charge process now...

Bug is fixed in the new firmware! Sansa Clip + Firmware 01.02.09 update

However, they say nothing about it in the notes, but it works for me!

Tags: SanDisk Sansa

Similar Questions

  • new sansa clip more 8 GB not detected but charge

    I got a sansa clip more 8 GB as a gift. new but old stock. everything works fine. except this is not detected by the pc. It will load.  I installed the drive, but I think that it isn't installed rhapsody. can I completely ignore the part of the Rhapsody? total newbie to mp3 sansa. I'm using windows media player 11, vista ultimate 64-bit version

    Miikerman wrote:
    As ends in General, no matter what Generic USB cable with straight plug should be fine with your drive. My hunch is that there may be some problems with the USB cable you have tried (something that you might want to check, by the way). Sometimes I use the USB cable that came with my Clips, sometimes I use one of my many generic not cheap-o cables; six of one and half a dozen of others - they all work very well.

    There is there the cables that don't transfer data, only the fee...

  • Sansa Clip Zip battery does not charge, goes directly to the screen of the song

    It's my third Sansa MP3 players.  The first was a Sansa Fuze with the round button.  Like that one but my husband needed more that I did it I gave it to him.  He is old, but the player is still so today.

    The second was a Sansa Fuze + with the touchpad.  The touchpad has been way too sensitive but I need to play only two songs for sleep therapy while I was fine with it until the battery suddenly stopped charging a few months ago, I posted my problems in the Sansa Fuze + forum.  After trying a few suggestions, I finally accepted that he was a Goner.

    I bought this Sansa Clip Zip 4 G, thinking that should last at least for a while because I use every day.  In fact, I needed only when I had disorders of sleep during the night;  I probably used it once every two weeks or more.  I used my cell phone to the device, had no problems until now.

    The last time that I loaded it was 2 weeks, to 98% full - the thing never indicated 100% while it was a little weird.  In any case, I had problems sleeping two nights ago so I took out the Clip Zip and noticed that the battery still had plenty of juice left.  This morning I checked the battery, he had 68%, but I thought I needed could again tonight so better it load up, just in case where.

    I connected it to my computer, but it did not show "connected" screen  Instead, he went straight to the last song I listened to.  I thought it was weird so I turned off the player then tried again.  Of course, he went directly to the screen of the song.  I noticed that the battery icon was showing 'filler '.  I thought that if I left it connected to the pc long enough IT would eventually deducted.  Two hours later, I checked the computer and it says that the drive battery was dangerously low.  I disconnected and then reconnected and this time he said 98% charged.  I loaded a bit more just in case so I used the player for about 15 minutes and the player turns off.  Plugged into the pc and now it says battery is extremely low, while the last hours do not charge the battery, but it drains pretty!

    My last attempt was to plug into a wall charger and guess what?  He went directly to the screen of the song once again.  Contrary to connect to the computer, I could actually turn off the player but this way does not charge the battery, or.   It's exactly the same problem as my second player, the Sansa Fuze +.

    I bought the last two players from Sansa, simply because I really liked the first which of course had been abandoned a long time ago.  I don't know if I have bad luck or it is just an issue joint Sansa players but one way or the other I don't buy any Sansa more in the future.  He is a big name that comes with the big disappointment!

    You can also try a reset by pressing and hold the power button for 20-30 seconds. Release it and then turn it on normally and see how it behaves.

    By your description of the message "dangerously low" you get then plug it into your computer, which tells me that you use MTP mode on the player (or default automatic default, MTP). MTP mode can be pretty weird; better to use MSC mode unless you have need to PSG for "protected" content or DRM files such as Rhapsody or audio in your library or Audible books. The small "crirically" message is a bug in Windows 7 (using MTP mode) that Microsoft did not consider important enough to fix.

  • New to the use of my Sansa Clip + full _ indicator of Charge

    I just purchases a Sansa Clip +.  I plugged it into my computer.  Did it come from, or what I need to charge for 3 hours straight out of the box.  Also... How can I tell when it is fully charged.  Right now I see a 'Connected' message and the battery flashes for about 3/4 full to full.

    It will stop flashing when it is loaded to 100%. I used my with a partial charge right out of the box, but then fully charged.

    When you start to use your Clip, do not rely on the load indicator until you get to know your little player.  My Clip + takes a reasonable amount of time down to a charge of 50%, but then falls to zero in an hour or two.  Initially it was quite annoying as my previous Clip did not do that, but I adapted.  Your mileage may vary...

  • Sansa Clip 2 GB shows "Connected" when the charger is plugged

    I have a Sansa Clip 2 GB is around the age of 6 months.  He played very well for 5 months, but for the last month, he periodically left the game and shows 'Connected' when the charger is connected.  I can sometimes turn off and on and it will start working again.  He will play for awhile, sometimes minutes, sometimes a few days and then stop playing again and see the "connected".  When he is in this state it will load but not play.  I tried 3 different Chargers and all have the same problem later.  I updated the firmware of 01.01.32 but no help.

    Someone knows how to fix this?  TIA for any help.

    OK, here is the last, this problem is resolved, but he caused a new sorta related problem.  What I did I deleted all my files and just put all the songs in the Music"" folder.  This seems to have solved the problem where it says 'connected' and stop playing, however, now it plays a day or two and then stops himself.  I just press 'Play' and he starts going again, so it is not much more than an annoyance I can live with that, and I could see where maybe he could do so on purpose after she played all the songs, but why it not it that way when I got it?  He played continuously day and night for months as a first step.  I'm confused, but I can at least live with the Clip now.

  • For sansa clip plus travel charger

    Hi, im newbie here! I would like to ask about a travel charger which is safe for my sansa clip plus. I have two things here:

    a. creative zen v more charger, spec: input 100-240VAC / 50-60 Hz, 0. 3a Output 5V = 1000mA

    b. charger RIM, spec: input 100-240VAC / 50-60 Hz, 0. 3a Output 5V = 550mA

    That is appropriate and safe for my player? Thanks in advance


  • Recharge Sansa Clip + with my Samsung 4.4V 400mA travel charger

    Can I use the Samsung BAG-48 (from my digital camera) to charge my Sansa Clip + and listen to the music while it is loaded.

    The technical data are:

    Input: 100-240V ~ 50-60 Hz 0. 2A

    Output: 4.4V 400mA

    Is enough enough?

    Thank you and best regards.

    xanilux

    Well, if the voltage is too high, it can fry the Clip. Don't know where the voltage is too low. Personally, I wouldn't risk, especially when the AC chargers are so expensive. Discover meritline.com where they are, is not uncommon for sale, for well South of $5 shipped.

  • Sansa Clip + does not start or is not recognized by my computer.

    I listened for the Sansa Clip + to work for about two hours after charging the battery. It stops all of a sudden. It will not turn on, nor is it recognized by my computer. I tried a soft reset by holding the power button and I still get nothing. I tried to connect to different computers and different USB ports on each computer. I can also load with another cord which is not read.

    Any help would be appreciated, thanks

    Have you tried holding down the power button (some say 30 seconds, but I don't think he'd be as long) and then releasing and clicking it normally? This is what worked for me both times as my Clip + died spontaneously.

  • It is the charger supplied with the phone. But my iPad charger is more than 2 years works great on my phone. What's wrong

    Whenever I plug my charger into my iPhone more 6 seconds I get a pop that says this accessory may not be recognized and will not take a charge. It is the charger supplied with the phone. But my iPad charger is more than 2 years works great on my phone. What's wrong? And why won't my charger. I also have another charger at work that the phone recognizes even plug me the charger in but that works well on a co-workers phone. Suggestions?

    Help here > power adapters using iPad with iPhone, iPad and iPod - Apple Support

  • Hi, I dropped my iphone6 in a salt water pool and was overwhelmed for only 3 to 5 seconds. I quickly ran upstairs to put it in rice and it was 2 days ago. Should I start charging or always keep rice?

    Hi, I dropped my iphone6 in a salt water pool and was overwhelmed for only 3 to 5 seconds. I quickly ran upstairs to put it in rice and it was 2 days ago. Should I start charging or always keep rice?

    Take your iPhone at the Apple Store as soon as possible. Unfortunately, warranty does not cover water damage. I'm afraid that your device is already damaged, but only professional can tell you this for sure. Take the sooner you it to the store - the best chance, it can be recovered.

  • Tecra A7: When the battery starts charging?

    Under what title did the Tecra A7 specifications battery start charging itself (when on a domain controller)?

    Hello

    In my knowledge ff as the AC adapter is plugged in the battery will be charged all the time.
    There is no level battery charge or does not charge.

  • When I connect my SanDisk Sansa Clip MP3 player Zip I get Code 10 device cannot start

    Original title: Code 10

    When I try to plug in my SanDisk Sansa Clip Zip MP3 player I get the device Code 10 cannot start.  I have XP.  The MP3 came with a 2.0 USB.  I don't know what the USB on my computer.

    Hello

    First of all, thanks a lot for taking the time to help me.

    After having tried everything you have suggested and have no chance and then by searching the Microsoft sites, Dell and SanDisk, I finally found a very simple solution that worked.

    Thought I would pass it for any future reference.

    The SanDisk site said to try this:

    Activation or forcing MSC mode on the Sansa player

    How to connect my Sansa in Mode "MSC" player or forcing MSC mode on my Sansa player?
     

    The steps below will force your readers Sansa Connect mode MSC on your PC.

    Sansa Clip Zip
    1. turn off the device.
    2 hold down the central button while connecting the device to the computer.

    Thanks again.

  • Fully formatted my Sansa Clip, in any case I can reinstall the firmware from scratch?

    I've deleted some songs using a Mac but noted they were still playable from my sansa and when I plugged on a PC the files not found so I decided it would be a fine idea to format the thing and reinstall from scratch.

    I'm having a little trouble finding how do and now starting to worry that my pure idiocy has ruined my sansa clip for me.

    I was running Rockbox when this whole thing started, if that helps at all.

    When plugged into a computer screen 'Bootloader USB mode' bed and when unplugged it reads "File not found", then "USB Plug cable.

    Thank you!


  • Will be for Sandisk Sansa E250 travel charger / E260 / E270 / E280 also charges the "rocket" SanDisk?

    Will be for Sandisk Sansa E250 travel charger / E260 / E270 / E280 also charges the "rocket" SanDisk?

    Thank you

    Yes.

  • 8 gb Sansa Clip play more hard

    The other day I went to play my Sansa Clip and noticed that the volume was not its usual volume.

    I immediately thought of the volume...

    He was already at its maximum volume?

    I usually play either this device through a pair of Sony headphones or my son amplifier (to play music and electronic together through).

    These TWO devices have the same problems - the MP3 player simply has not played at the high plus volume.

    I haven't played around with what anyone on the device, the Clip had a life good and safe, not been stamped on, thrown autour etc etc.

    In my view, it is guaranteed for one year, but I did keep the packaging, etc. - he bought off Amazon.co.uk.

    Any ideas?

    Thank you

    Jez

    Solved !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    It was done by the rearmament of the factory settings and selecting North America (even if I'm in Europe) who turned my Sansa Clip love to produce that its very nice!

    Yay!

    Forum thank you

Maybe you are looking for

  • Setup automated uninstall of firefox for a total clean

    I noticed that after installing firefox 40,0 sha 512 84228c5e70b0ca4b3a8444007691a06cac1ecb6d81995d11a225e6e29dac6799267ebfe60488d0934e32567599c6a4ef0f849dfddbbfd3abdf0b0282599f10c3 cleaningWhen I get the Ebay order I am directed to Paypal and automa

  • WRT54G V3.0 Web Interface broken after FW update

    I meet the same web interface problem after I updated the firmware, like in the case below, but with my v3.0 WRT54G. The firmware file I upgraded to was WRT54GV4.0_4.21.1_US_code.bin. Will provide you with instructions and decommissioning file name s

  • Desktop shortcuts for items on the network sometimes drives disappear from the Office

    I have a number of shortcut icons on my desktop Windows 7 (RC1) to the network elements - some are files on a NAS server, some are mapped as the floppy drives, etc. However, Windows 7 seems to sometimes simply remove all without notice, and I have to

  • Not able to launch the program created in c:\Windows.

    Original title: series of order details I put a shortcut to a program on C:\Windows, so I can type his name on Run and launch the program But, Instead, it prioritizes an incorrect executable of a program that is installed with the same name How to ch

  • SQL * plus - formatting issues

    Hi Experts,I am trying to generate several reports using SQL * MORE tool (SQL * more: 11.2.0.1.0 release). I am facing problems of formatting the output.I developed a .sql script like below. TERMOUT OFF SET SET PAGESIZE 50000 SET LINESIZE 32767 SET T