Satellite A100-409 restarts a lot due to BSOD

Similar Questions

• Re: Satellite A100-409 tends to overheat

  Hello everyone,

  My Satellite A100-409 tends to overheat after a few minutes of use, just to watch my mail or browse the internet, use simple and normal.
  The mouse pad has a tendency to overheat as well. I try to keep my dust-free specifications, but it's not helping and my left leg Burns!
  Someone at - it ideas on what can be and how to fix this? The use of a Kneeler is not an option!

  Thank you very much in advance for your suggestions
  Fabio

  Hello

  Your laptop computer shut down automatically?
  If you didn t notice any unexpected shut downs, then the computer laptop doesn't overheat!

  > The mousepad has a tendency to overheat so
  My touchpad is too hot. This is not unusual due to the internal temperature for laptop!
  The laptop as CPU and GPU parts produce a lot of heat and, therefore, the other parts may be hot too.

  > I try to keep my dust-free specifications, but it's not helping and my left leg Burns
  I see you don t use the laptop on the table. This is the main reason why the laptop can not be properly cooled and raises the temperature of laptops!

  Look, the vents are placed at the bottom of the unit and they must be free! It is very important to ensure a flow of ACI cooling properly and very fresh!
  In addition it should be always enough free space around the laptop even if the laptop was sitting on the desk.

  So, don t use in bed, sofa, sofa etc is undesirable and very risky because notebooks cooling module does not work as it should.

  Concerning

• Re: Satellite A100 keeps restarting itself of the option safe mode screen

  Hello

  I had a search but I couldn't find all the topics that have the same problem as mine, I maybe could have missed one:------.

  My laptop froze this morning so I had to reset by holding the power button down, then when I went to turn it back on, it goes to the screen of the safe option mode where it gives me the following options:

  safe mode
  safe mode with networking
  safe mode with command prompt

  last known good configuration

  Start windows normally

  I tried all of the above options and whenever one of them is selected, it starts to load Windows with blue small bar that hangs, restarts and repeated everywhere: S

  I hope that someone can help me, my life is on this laptop and I would be devastated if I lost it all lol

  Thanks :)

  Nadine

  Hello

  Looks like bones corrupt bootloader. The easiest way is to reinstall the operating system...

  > Hope someone can help me, my life is on this laptop and I would be devastated if I lost it all lol

  If you have important data, you can extract it using Windows live cd. Get it and boot from it and move important data on USB.

• System of Satellite A100 restart when I eject a CD CD-driver

  Hello

  I have a problem with my Toshiba Satellite A100, when I eject a CD CD-driver, computer restart.
  Could someone help me, please?

  Best regards, Robert

  Which is really strange, I know that the laptop could happen again if an error has been detected.
  So in my opinion that the internal CD/DVD drive could cause this strange restarts automatically.

  It would be very interesting to know if the same thing will happen with a new CD/DVD drive. I think you do not have the opportunity to test this and therefore, it would be advisable to contact the service provider authorized in your country for these audits.

  But wait; have you tried to update the operating system and boot from the restore CD?
  Try to reinstall the OS from the original Toshiba Recovery CD and check if the same will happen in fresh, new OS.

• Satellite A100-785: router restarts automatically when the wireless network card is on

  Recently,.
  Once, I turn my adapter wireless for my laptop 'ON' and it starts to connect to my router 3com officeconnect wireless.
  I found that my router restarts automatically.
  This happens each and every time I turn on my laptop with the wireless adapter ON.

  I use the Satellite A100-785 PPPoE ISP with WPA/AES encryption enabled on the new MS Vista platform.
  All drivers updated to the latest versions, and the wireless signal is Excellent.

  Any suggestions that could be the reason or any recommendation to begin to investigate the matter?
  Everything will be highly appreciated. Thank you

  Once again; Your WLan router restarts (reboots) when you turn on the WLan on the A100 Satellite Map. Am I wrong?

  Well, it's strange, but to be honest I n t see a problem with the laptop but with the router. I would recommend controlled again the unique WLan router configuration.

  Good bye

• Satellite A100 restarts when HDD WD connected?

  Hi, I searched this issue in this forum, but I don't find it so here you go.

  I recently bought a WD portable hard drive and when I plugged, he enrolled in the icon section, then it would go to a blue screen and do a reboot even time I had connected hard drive. He wouldn't even give me the option/Assistant to install the program.

  My laptop is S100 998. I took it to where I bought and received a refund. They have had problems with it on his computer to test as well. I tried another unit in the store and he did exactly the same thing. Finally, I tried another brand that worked well, but the whole point of getting this portable hard drive was because of his rep.

  Do you think it's my phone who is at fault with the type of hard drive, or they are not as good as they say.

  See you soon

  Boyfriend sorry but if people in the store say that hard drives are not so good, why do you now your laptop is not OK?
  Either incidentally, S100 998 is unknown to me. Maybe you have Satellite A100 and not S100.

• Satellite A100 - unrecoverable system error and restart

  Without warning my Satellite A100 don't close but reboot, I removed the auto reboot, and the error that is displayed in the BSOD is:

  STOP: c000021a {fatal system error}
  The Windows Logon Process system process ended unexpectedly with status 0xc0000000 (0x00000000 0 x 0000000)

  in the event where Viewer does not appear anything on the error, I tried a system restore but it cannot exercise, in the event viewer this time it is written that he cannot run because the PC is not turned off regularly,
  How can I do?
  The BSOD appear in the last stop after the color screen when turned on the black screen just before the
  Turn off the power.

  your
  Fabio

  Hi flottero,

  It of always a little difficult to discuss these blue screens because many things could be the reason, but in most cases it s a hardware or driver problem.

  If system restore doesn't work, can you try to restore Windows recovery disk settings, please? After that, you get back factory settings and so you can identify a hardware problem or software.

  Check this box!

• Satellite A100-683 with Win 7 - screen brightness adjustment does not work

  Hello

  I have a model of Satellite A100-683 PSAA9E with Win 7

  My problem is that I don't have a brightness in my dashboard-> laptop Center

  I tried to install the drivers from the site Web of Toshiba (additional package, return), but stops the installation always with errors such as: value added package: PVAT Setup error

  I tried to install the drivers for Vista...

  Please help me!
  Sorry for my English mistakes.

  Hello

  The installation may stop due to system problems or the PVAT erroneous version.
  I recommend you to uninstall the installed VAP.
  After the PVAT has been uninstalled, restart the laptop.
  Now, download and install the tool small freeware called CCLeaner.
  It helps to clean the system and deletes files temporal garbage from the HARD drive.
  After the cleaning of the system registry, you must restart the system once more.

  Now, go to the page of the Toshiba UE driver and download the Toshiba value added Package for Win 7. Note! Choose the right! There are differences between the 32-bit and 64-bit version.

  Unzip the package, run the exe from installation or installation file and start the installation.
  Installation should finish properly and after new reboot, you should be able to use the function keys.

• Sound problems after installing Vista on Satellite A100

  Hello

  I have something new, something I've never seen and I do not much [as appropriate] of you.

  Today, I installed Windows Vista Beta 2 on my laptop Satellite A100-192. As it is Vista compatible now [I added some memory] I think it's the right time to see the new operating system [that is great, he will rule the world for sure].

  But back to the topic.
  After the installation of Windows Vista, which has detected almost all of the software in my pc and have fun on this topic / and there are a lot of things an old fart like me, can have fun with / I decided it's time to get back to work.
  So I restarted my toshiba for win xp, started working and has decided that music will surely improve my / concentration i'm from Poland and as many of you know, my team lost the first game of the 2006 World Cup. so they will not pass the group stage of WC2K6--real cause my humor today. After turning on my foobar, I realized that I don't hear nothing/i do not drink, so he can't really be the cause. I've set all volume settings, all the settings of the sound and nothing! I tried headphone jack, but it does not work too. I tried reinstalling the drivers, reboot the system several times and... nothing.
  I went back to Vista and... sound works like a charm.

  Bromine to Vista my sound on XP...

  Anyone has any bright ideas, how this could have happened and how to solv it / accept to remove vista from windows...?

  I would be greatfull for some advice...

  Best regards
  Krystian

  Hello Krystian

  If you use recovery media supplied for installation of WXP is the noise problem persist?

• Satellite A100-803 - Vista recovery problem

  Hello

  I upgraded the RAM and HDD on a Satellite A100-803 and when I restore Windows Vista from the recovery disk process is going very well, but after restarting windows says that "Windows Setup could not set up Windows on this s material.

  I think that the problem is listed here.
  http://support.Microsoft.com/kb/2466753/en-us.

  But the problem is that I can't change the RAID setting in the BIOS, and during the installation of recovery, I'm not able to add the additional drivers needed.
  The new drive is a WD 500 GB driver (WD5000BPVT)

  How can I solve this problem?
  Thanks in advance
  Pau

  Hello

  First I put t think its BIOS problem.
  The laptop doesn't support RAID.

  I think the problem is the size of your new HARD drive. Upgrade of the disk HARD 500 GB and its larger than the original HARD drive equipped in A100.

  The point is that a recovery disk automatically creates the partitions on the HARD disk, but due to the size of the disk HARD the size of the partitions would be different also.
  I think that you won't have the same problems to install Vista or Win 7 using the Microsoft disk

• Satellite A100-680: PnP BIOS Extension missing driver

  I searched for about one hour now, other threads from reading and the search manually through the database of the driver, but I can't find any useful information.

  As you can see from the following screenshot...
  [http://img528.imageshack.us/img528/3171/prtscr2.jpg]
  ... I am missing a driver.

  I'm sure that the driver is listed, but it can also be saved under another name. This isn't something I'm infamiliar of searched a lot on other sites (Acer, HP, etc.) for drivers of other computers in my work.

  Anyway.
  The reason why this driver is missing on my * Satellite A100-680 * is that my antivirus detects it as a keylogger. This is not the first time that this happens, and I can easilly restore virus vault if I want to. However, this is something I really wish to do.

  This problem also occurred with some of my audio drivers earlier, as well as the driver associated with TOSHIBA Hotkey functions. (Solved).

  In order to check for me if my antivirus detects a false positive or not, I would like to find the driver and install it.
  If after this my antivirus detects it as a keylogger, it was just all along.
  If it detects it as a keylogger, I treat the result as a false positive and add it to the white list.

  My Toshiba is a Satellite A100-680, running Win XP Home edition.
  The version of the BIOS is "Phoenix Technologies LTD. 1.70, 11.05.2006" (from msinfo) (whether this info is helpful at all is beyond me...)
  SMBIOS version 2.31 (new msinfo.)

  If you need additional information in order to help me, please indicate what information you need.

  concerning
  TTRM

  Have you tried to remove this device in the Device Manager list and restart the laptop?
  Try this! After restarting again the operating system must search for the driver and must be reinstalled this device automatically.

  By the way: Satellite A100-680 belongs to the PSAA9E series.
  The European driver Toshiba page provides up-to-date BIOS 6, 00 - WIN for this device
  Recommends the installation of the Modules common to XP and BIOS update.

  Note: for drivers, please choose 'Archive' types of products

• Satellite A100 - sound turns off randomly

  OK, it was my fault. I lent my laptop to one of my students who tried to load a software to read a FLV file.
  Since then, I had a lot of problems with my sound.

  The sound would work, but when the volume is too high or often at random - the sound would cut out them and stop them.
  The sound level meter shows that sound is working.
  Mixer indicates that the driver is working.
  But I do not hear anything from the speakers.
  Only when I stop and restart the sound coming back.

  I downloaded the sound driver Toshiba Real Tek recommended, but this has not solved the problem.
  I completely rebooted Vista and all my software, but this has not solved the problem.

  I have a Satellite A100 PSAANC WA07
  Microsoft Windows Vista Home Premium SP1
  BIOS Version 6.00
  RealTek Audio driver 6.0.1.5326

  Any suggestions would be greatly appreciated.

  Hello

  It s really strange that your problem persists after that you got the laptop.

  What you could do is visit the site Web of Realtek and could attempt to reinstall the audio driver directly from Realtek page.
  Before installing the new version, he recommended to remove the old driver sound system.

  Welcome them

• Satellite A100 (PSAA9A) - sound doesn't work - tried all of the obvious solutions

  I have a satellite A100 (not sure the model, but the model is PSAA9A-00S00F)

  The sound does not work, but I haven't used the noise for about 7 or 8 months ago.
  Mute is not on, all volume controls are ok.
  There is only the internal speakers.
  I downloaded the current drivers.
  Running Windows XP Pro.
  I did the Windows updates that I can find and made the process of troubleshooting through Windows.
  I'm out of warranty so wouldn't send away to get looked at unless absolutely necessary due to cost.

  The CD/DVD drive is not read, but the sound is not related to this, because it will not healthy for web content.

  Someone at - it other suggestions of what could be the problem?

  Thank you!

  Hello

  You reinstall Windows or only the sound suddenly stopped working?
  And the sound card is in the Device Manager? There are some yellow exclamation points?

  Before installing the new drivers, you must remove the old drivers first. This means remove the older version of the driver and the software, and then restart the laptop. Use CCleaner to clean the registry and restart. After this installation, the latest driver from Toshiba Europe page.
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  In addition, make sure you have these two installed Microsoft Hotfixes:
  AUDIO Patch1: Http://support.microsoft.com/kb/835221 KB835221
  AUDIO 2 Patch: KB888111 http://support.microsoft.com/kb/888111

  Welcome them

• Last updated by Satellite A100-289 with a new CPU and additional RAM

  Hello. Sorry for my English in advance :) I have a laptop Toshiba Satellite A100-289. Despite I am satisfied with the laptop, it is possible for me to update, so I have a few questions on this topic.

  Fact laptop support Modules-SO-DIMM 2 GB of RAM? Also, what mobile CPU is supported for upgrade? Is it possible to replace the Core 2 Duo T5500 (default), with a few other Core 2 Duo processor, such as T7400, T7600, T7700? And if I install a new processor, it will influence the energy consume and warming temperatures drastically?

  Thanks :)

  Post edited by: mister yetti

  Hello

  with regard to your question: Yes you can.
  Usually your chipset is capable of a maximum of 4 GB of RAM, but due to the limitation of the slots (Slot 1 cannot handle a 1 GB module), you can move only to 2 GB maximum, because your machine has only 2 slots.

  And what with your CPU? You can certainly try, but you won´t have a lot of luck. Excluding the small fact that each machine has it s own system of cooling for the processor which is equipped with this machine.
  the won´t CPU run at full speed.

  Why not? The problem is and now speak from experience;) that when you replace the processor in a processor intel pentium M or Core(2 Duo) system, something in the bios change, then the new processor
  will not properly recognized. And then the old? Nope. After you swap the CPU, you will have to bring your machine to an ASP.

  They have software that reactive something in the BIOS and the CPU runs at full speed. Since then they to the ASP will notice that you tried to Exchange something in the Board of Directors,
  you will face a cancellation of the guarantee and you will have to pay for everything that happens to be broken after the revocation.

  So I propose: update your RAM, but don t touch your CPU.

  Have a nice weekend

• Occasional hang up IE and hibernation on Satellite A100

  Hello
  I have a Satellite A100 with Windows Vista. It works fine, but I have two problems:

  -Sometimes Internet Explorer crashes upward, often the whole system "freeze".

  -The system does not properly recover after hibernation. It seems to revive activity, but then the splash screen, showing the Toshiba logo appears, like when to turn on the computer.
  Then a blue screen displays a quick message, report an error or a problem (sorry, the text flows and disappears too fast for me to read) and I get a message asking if I want to solve the problem that led to an abnormal termination upward by booting in safe mode or start Windows normally.

  Can anyone help? I'd appreciate any help. Thanks in advance.

  PS apologies for my English...)

  Hello

  just a few suggestions, maybe not all the resolution but useful:

  Regarding your problem of IE
  1. perform all updates, you can get (windows, 3rd party software, etc...)
  2. install an anti-virus program if it isn't already (a good is Avira anti-virus and it s * tadaaaa * Freee!)
  3. use Mozilla Firefox instead of M$-IE, it s faster, not so buggy and there are a LOT of free plugins for him :)

  What about your sleep problem extended:

  1. update your bios to the latest version available.
  2. to read the blue screen, do the following:

  Make a right click on 'My Computer', then left click the "Advanced" tab, and then click settings in the 'Startup and recovery' section, then uncheck the "Automatically restart" under "System failure" and now able to read you´re today described the BSOD (Blue screen of Dea *)

  That s all I can tell you

  Welcome them