Satellite A500 - USB devices not detected

Similar Questions

• Satellite A500 - USB devices not recognized

  I have a new Satellite A500 and it now will not 'see' one of the connected devices (Modem 3 G, an iPhone). I checked on Device Manager and it is showing as active USB ports and works correctly and has run the PC Diagnostic tool, which showed everything (including USB) in the work.

  Can anyone suggest how to fix this?

  See you soon,.
  GG

  Hi GG,.

  I think that it of difficult to say something about it, if you display any information about your operating system.

  The only thing I can suggest to remove all the USB ports on the Device Manager and restart the laptop. The USB ports will recognize again. In my case it worked and I was able to reuse my USB devices. :)

• Satellite L30: Usb device not recognized

  I have a problem with my laptop L30.
  When I connect my phone or a flash drive or external hard drive, it is said: Usb device not recognized one of the usb devices malfunctioned.
  Tried to reinstall windows did not help...

  is there a solution?

  Hello

  Hmm. First of all, you should unplug all external USB devices.
  Then go to Device Manager and remove it all concentrators root USB and USB host controllers.
  Reboot the laptop.

  After this procedure, the operating system should recognize and should install new ports.
  Now you can connect to a plug - and play instruments. These devices should be recognized automatically. But some external USB devices need additional drivers.
  Usually these drivers are provided with the USB device.

  I would recommend this review if necessary!

• Satellite A500-19W does not detect battery

  Hello

  I have a portable Satellite A500-19W which is 6 months old.

  I bought this laptop while I was in Egypt and now I've moved (Dubai) UNITED Arab Emirates.

  Lately my laptop started suddenly does not detect battery.

  To remedy this that I have to remove the battery and clean the terminals then re - put the battery and turn it on and it's OK.

  This happened twice this week and caused my data loss because the charger is disconnected (if the charger is connected, the laptop computer continue to work, but the battery indicator does not light up)

  Now, my questions are the following
  1 - is this problem under warranty?
  2 - should I pay for anything when getting this laptop in service in Dubai noting that I bought in Egypt?
  3. is there a cure for this problem without going through the service center?

  Thank you

  1 / Yes. These questions should be covered by the warranty. Material is junk.

  2 / the nearest service contact and ask, but I'm sure you don't have to pay for the repair. The two countries are countries in EMEA, and avoid any kind of problems.

  3 / it is not much, you can do about it so please contact and explain the situation. They should check your laptop and find a reason why this happens.

  Don t waste your time and contact the closest service. If you have need for addresses and phone numbers you can find on http://eu.computers.toshiba-europe.com > support & downloads > find an ASP.

• USB device not detected.

  Original title: USB device

  I can't get Windows 8 to detect my USB video to DVD connector. I installed the necessary drivers but nothing seems to work.

  Thank you for your answer

  Apparently, the USB connector is damaged or has simply not. I took it to a computer store, their computer could not detect the connector either. I think I'll buy another connector $ 49 after only 3 years.

  Thank you

• Satellite A500 - 18Q - battery not detected after installing Windows

  I have Satelite A500 - 18Q (PSAR3E) and Windows 7 32 bit

  Windows is not detected battery. What should I install to the Windows recordnize the battery?

  Hi marnin,.

  Have you installed Windows Toshiba Recovery disk or normal drive of Microsoft?

  Normally for the battery you n t need an additional driver. He will be recognized automatically.

  Can you charge the battery when the laptop is turned off?

• Re: Satellite L645 - peripheral Bluetooth not detected

  Hey, prior to that, I can use my bluetooth anytime, anywhere... but last night, I tried to receive an item from my phone, and it seems that my bluetooth device does not.

  I am looking in my cell phone, and bluetooth bluetooth Manager setting and etc are still there. When I click on Bluetooth, not had a response Manager. but in my task manager, the program works very well... I try to find FN + F8, my bluetooth is turned on. so, I tried to re - install back than my bluetooth stack, but the same problem occur... I tried to use other bluetooth software, but during the installation, he said that "no bluetooth device not detected"... so how to solve this problem? Transfer that my bluetooth works fine... Please help me... =)

  Hey,.

  What model Satellite L645 you have exactly?

  Not all L645 models have Bluetooth module

• USB Device not recognized Hp OfficeJet 6600

  Hello all - I use my desktop Hp 6600 (connected via usb) jet and my computer (dell E6430 latitude) says that it is a usb device not recognized.  I tried a lot of troubleshooting, including the removal of usb controllers and reinstall, but which doesn't seem to work.  I'd like to help as soon as POSSIBLE. Again, I must keep my printer cable, because the network, I refuse the acess printers or something like that.

  Thank you

  J

  Hello

  If I understand correctly your computer does not detect the printer. You can try the following steps and check the results.

  1) inspect the cable USB and connection:- icon on the USB () facing up when the cable is connected to the product correctly. Check the back of your product and the back of your computer to make sure that the USB cable connects correctly and safely. After that you make sure that the USB cable connects correctly and safely, consider the following guidelines to check other potential problems associated with USB: Connect any other USB device. Connect any other USB device to the computer and check if it is detected. USB ports on the keyboard. USB ports on the keyboard and on the front of some computers is maybe not powerful enough to support the product. If the USB cable connects to the USB port on the keyboard, try to connect to it in another USB port on the computer. Length of the cable USB. HP recommends that the lower USB cables or equal to 5 m (16 ft 5 in) long. However, a USB cable which is 5 m (16 ft 5 in) in length must be of high quality. Otherwise, HP recommends using a USB cable that is less than 2 m (3 ft 3 in). Do not use connection cables to increase the length of the cable. Use a powered USB hub, if you need more length. USB ports replacing. Connect the USB cable to a different port on the computer to make sure that the USB port on the computer is not the cause of the problem. Defective USB cable. Replace the USB cable to ensure that the existing cable is not defective. Conflicting USB ports. Disconnect all other USB, USB, USB cameras scanners printers and all other connected USB devices. Start the connection of these devices one at a time to determine if the devices to use too much power. Plan to buy and install a hub USB powered if necessary. (2) power Off and power of the device. (3) update the Windows Device Manager: (a) click Start (for Windows XP) or the Windows Logo (for Windows Vista and 7), and then click run. The run window opens. (b) in the Open text box, type devmgmt.msc and press ENTER. The Windows Device Manager opens. (c) lists to look for your HP printer in Bus USB controllers or other devices . (d) right click on the entry for device to device/unknown HP and then click on set to update driver. The material up to date hospitality Assistant opens. (e) select install the software automatically and click Next. Follow the on-screen instructions to complete the refresh Device Manager. (f) repeat these s for all entries of device with a yellow exclamation point. (4) delete the temporary files and folders. (5) disable some startup items: -. (a) click Start (for Windows XP) or the Windows Logo (for Windows Vista and 7), and then click run. The run window opens. (b) in the Open box, type msconfig, and click OK. The System Configuration Utility window opens. (a) click on the general tab, click Selective startup. (b) if there is a check next to load startup items, select the check box to remove it. (c) click on the Services tab and then click on the hide all Microsoft Services check box.

  (d) click Disable all.

  (e) click on apply and then click Close.

  (f) restart the computer.

  (6) make sure that the Plug-and-Play Service is activated: -.

  (a) click Start (for Windows XP) or the Windows Logo (for Windows Vista and 7), and then click run. The run window opens.

  (b) in the Open box, type services.msc, and then click OK. The Services window opens.

  (c) to seek the 'Plug-and-Play services' and check if the status is started.

  (d) if the status is not started, then right-click on it and select start.

  (e) once on the way out of the window.

  (7) uninstall and reinstall the printer software.

  (8) re-enable the startup programs: -.

  (a) click Startand then click run. The run window opens.

  (b) in the Open box, type msconfig, and click OK. The System Configuration utility window opens.

  (c) click the general tab, click Normal startup.

  (d) click the Services tab, and then select the hide all Microsoft Services check box.

  (e) click applyand then click close.

  (f) click on reboot to apply the changes to the next time the computer starts.

  (9) try to install the software on another computer.

  Although I am an employee of HP, I speak for myself and not for HP.

  -Say 'Thank you' by clicking on the star of congratulations in the post helped you.
  -Please indicate the position that solved your problem as "accepted Solution".

• USB problem-"USB device not recognized".

  Original title: USB problem

  I have a problem when I connect my nokia mobile to my pc via USB cable there is a display of msg of error "USB device not recognized.how to solve this problem? I tried all reboot pc, reconnect the device, format XP and reinstall.last night I was using a mobile navigation correctly with the same device same system same cable.i have tried driver re install but not fixed yet.i have Windows XP 3 intel p4.please help.

  Hello

  1. Are you having the same problem if you connect a drive flash or any other device?
  2. Have you tried plugging in Nokia mobile on another computer?
  3. Have you tried plugging it into different USB ports?

  I suggest you send more information to help you better.

  You can also refer to:

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive.

  http://support.Microsoft.com/kb/925196

  USB port may stop working after you remove or insert a USB device.

  http://support.Microsoft.com/kb/817900

  .

• O2 dongle is never to step of the password and then just says device not detected / found

  Original title: im trying to use my o2 dongle to connect to the internet, but for some reason some he used to let me...

  Ive connected the dongle and it goes through the normal treatment it says connection. However, it's never at the stage of the password and then just says device not detected / found

  Hello

  You can try to reinstall the USB controllers and check.

  a. Click Start and type devmgmt.msc and then click OK.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  f. check the device to see if it works.

  You can also consult the following link:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Hope this information is helpful

• message usb device not recognized guard appearing, none of our devices work

  None of our usb ports work so that we cannot use the printer, mouse, or plug in our camera we get the message this device is not recognized. We have a laptop

  Hello

  Check the settings/configuration (BIOS/CMOS) that get started - often F2 so watch you start screen.
  Check that the USB is enabled. If these methods fail you will need a real computer store
  (not the leeks and the glances at a BestBuy or other big box stores) or Technical Support from the manufacturer of the system.

  ------------------------------------------------------------------------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  Do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick the three 1st choice
  to see if one is there. You can remove all instances of any individual device and then restart to see
  If this device activates.
  http://www.NirSoft.NET/utils/usb_devices_view.html

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• USB device not recognized error

  I am running Windows 7 on an acer 4810 t
  My computer keeps telling me that I have an unknown USB device.
  In Device Manager, the device will appear and then disappear every few seconds.
  The only USB device I have ever used with this PC is an external mouse.
  Initially, the error occurred when I had Vista and I assumed 7 upgrade fix it - no luck.
  Until I disabled all notifications error that it made my laptop unusable.
  Is it possible to fix this problem without having to reinstall the system.  Please?

  Hello

  References to Vista also apply to Windows 7.

  There may be devices USB internal connection such as keyboards, cameras, card readers, of fingerprints fingerprints devces,.
  and others. All that you have people don't seem to have problems? This could be a hardware problem. What do you see
  This is when he jumps up or at least which category in the Device Manager it appears?

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  After having updated the USB stack:

  USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all
  USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.
  This might help determine the device that is real or not.
  http://www.NirSoft.NET/utils/usb_devices_view.html

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Windows 7 - "USB device not recognized" - to load the new electronic Cigarette device. Help, please?

  I have Windows 7 Home Premium.  I just bought a unit of the electronic cigarette, manufacturer is "Innokin Cool Fire IV", the usb charger plugged on Acer laptop and comes to the screen "USB device not recognized".  I loaded different brand before without problem, I don't know what to do and I am NOT GOOD WITH COMPUTERS!  My settings are at "install updates automatically" and I DON'T WANT WINDOWS 10!  Can someone help me please?  Thank you for taking the time to read this.

  This seems to indicate that the charger has actually been detected as a device, but Windows can not work it out.

  Normally such a device should only connect to 5v and 0v pins and have no connection with the pins of data, in this way, that it will not be seen by Windows. I would be concerned by the quality of the device if it has some form of data connection. If you want to continue with this charger, that I would recommend to use a power supply of 5v USB instead of risking the USB port of the laptop, a lot less expensive if it does not. It has been reported several eCig Chargers catch fire. Something like this:

  

• Error "USB device not recognized" but nothing is plugged

  Hi, this problem recently just started to happen, nowhere I can say. Whenever I turn on my computer or it wake up from hibernation, a message from the task bar appears saying "USB device not recognized". However, there is nothing plugged one of my USB ports. I have three USB ports available, and all are empty. I tested all three ports in something by plugging, and all three ports seem to work well. What can I do to get this message to stop appearing? Thanks in advance!

  Hello

  Some USB devices are integrated as WebCam, Touchpad, fingerprint and other reader, so it could
  be people or a total glitch.

  ----------------------------------------------------------

  References to Vista also apply to Windows 7.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the driver and battery USB

  This KB shows XP how to and methods of Vista and Windows 7 are the same
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick three 1
  are there choices to see if any.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• my USB is not detected in my pc, but it is detected other pc and laptop. and if I restart my computer at that moment there, it is detected.

  I have lenovo ideapad laptop z580. i5, family basic Windows 7. in the week, I have a problem as "my USB is not detected in my pc, but it is detected other pc and laptop. and if I restart my computer at that moment there, it is detected. "so please give me the solution. Thank you. my email is * address email is removed from the privacy *. Thank you.

  Hello Badodariya Malay,

  Welcome to the Microsoft community where you can find all the answers related to windows.

  According to the description, it seems that you are having problems with pen drive not getting not detected.

  I need to ask you some questions to help you better.

  1. don't you get error message when the USB not detected?

  2. What is the brand and model of the USB?

  Perform the steps in the link and check.

  Tips for solving problems of USB devices 

  Answer to us if you are having problems with the USB key or any other problem of Windows, and I'd be happy to help you.

  Good day!

  Hope this information helps.