Satellite L300D cannot detect the wireless printer

Similar Questions

• Photosmart C6180 cannot detect the wireless network

  I have a Photosmart C6180 for over a year, and until recently it connected wireless very well.  But since a week ago, it can't detect the wireless network.  I turned off the printer and wireless router several times each without success.  The "Wireless Setup Wizard" running on the C6180does not help. Watch simply screen printer "looking for... wireless router. "indefinitely, until the function Cancel.  The wireless router is about four feet from the printer, in a direct line of sight.  In addition, I have wireless Internet access using the same router and continue to do this successfully, then the router itself works.  Recently I have updated the firmware on the router as well (after the beginning of this problem).  Running the network Test report wireless on a 'PASS' C6180 returns for "Radio on" but a "FAILURE" for "use of Radio". The radio broadcasts as "about" section of the Menu Radio wireless network.  My router is a Belkin Wireless G Router model F5D7230-4.  The printer prints very well with a wired connection, but wireless connectivity has been a key reason behind my purchase.  Any suggestions greatly appreciated.

  Sorry, but your wireless radio is dead.  Its time for a new printer.

• RT of Windows cannot locate the wireless printer

  I have a new Surface Windows RT (not 8.1) and I'm unable to connect to my printer wireless on my home wireless network.  The printer (Brother MFC-J625JW) is listed as a compatible printer Windows RT by Microsoft and brother.  My printer is on, visible on my laptop Windows 7 via the wifi network and works normally.  The Surface is connected to the same network.  I entered in the control panel > adding a device.  The printer does not appear in the list.  In fact, the only thing that appears in the list (momentarily) is someone from another PC - but not my printer.   How can I get the Surface to find my wireless printer that seems to operate other devices normally and is on the same wireless network?  Thank you.

  Success.  The wireless printer now appears in the "Devices list".    The breakthrough came after installing the Windows Update screen Firmware updates.  I had already updated for Windows RT 8.1 (after my original message) from the window Store (free), but that has not fixed the problem.  I then went in the Panel, search the Windows updates.  Windows found 27 updates of firmware update that it installed.  2 reboots are needed.  After that, the printer has appeared in my list of devices.

  In response to your questions:

  1. & 2.   You are right: it is the MFC-J625DW.

  3. never checked directly connect USB since the Surface RT (now 8.1) was showing the printer.

  Thank you.

• Windows 7 can't detect the wireless printer

  I recently bought a Canon MG5250 1 wireless printer while. I got it connected to my router according to the Canon instratuctions, I have a laptop with XP that I have completed the installation with a CD, it detects the printer and print wirelesly without any problem. I can ping the IP address of the laptop XP.

  However, I have a 32 bit Windows 7 laptopn which can print on the MG5250 via USB but the installation CD does not detect this wirelesly, he cannot ping the ipaddress either. I tried to install with all firewalls and the disabled antivirus scans and network settings are set to automatically detect the network. I have connected to many networks account invited to the clients and Hotels without problem.

  Can someone help me please?

  Hello
  Please see this thread.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Canon-software-for-MG5250-printerscanner-wont-work/dadab50e-1021-4F03-bf00-261929e1317b

  Follow the two links in the response from Imran and you should be good to go.

  I hope this helps.

• Portege 3490CT: operating system cannot detect the wireless network card

  Hello
  Portege 3490CT with windows XP

  Problem: Try to install the wireless lan card. Windows is not able to detect the new hardware.
  Details of LAN card are NETGEAR 54 Mbps, model WG511v2

  Specifications for lan card
  It is 16-bit PCMCIA and CardBus 32-bit compatible and works in any available PCMCIA or
  Location CardBus. IEEE 802.11 g and b standard wireless technology.

  Specification for laptop Portege
  PC card slot supports two Type II or Type III PC cards; R2.01 PCMCIA, CardBus, PC Card16

  all tracks on this will be very useful
  Best regards
  Ashwani

  Hello

  What the BIOS has been installed on your laptop?
  If you use the Toshiba BIOS so there could be an option called configuration of the device.
  (it s is available on my Satellite)

  You change the option for all devices, you will be able to change the PC Card controller mode. I think you should play a little with this option.
  In other cases, the user was able to resolve a similar issue by changing this option.

  Please report if you re successful because it would be very interesting for me.

  Good bye

• Satellite L300D - cannot find the XP driver for the graphics card

  Hello

  I just bought a Toshiba Satellite L300D and I installed Windows XP (instead of vista, which was preinstalled). I can't find the XP driver for the graphics card... Everest recognizes him as ATI RS690M. A download link will send me straight to heaven!

  Thank you in advance,

  Nikos

  PS. of course, I searched the display on the sites of several Toshiba driver and I got this message: "the resource you are looking for has been removed, had its name changed, or is temporarily unavailable."

  After that, I tried the driver from ATI, and it seems that they are more home driver for XP.

• Windows xp on te2000 cannot detect the wireless LAN card

  I have a portable te2000 that the wireless lan card is detected as PCMCIA MTD-0002.
  I downloaded the drivers, but once again I installed windows will not use it. I get the error code 10.

  How can I make it work?

  The wireless port is enabled, but it has an orange light (not green) no idea why?

  Thanks in advance
  Ken.

  Hi Ken

  Use this original device ORiNOCO Mini PCI Card (comes with) or if you use an additional card? The unit is pre-installed with the original recovery CD?

  According to the specifications of error 10, you should try to update the WLAN driver.

• Dell Inspiron 14r 5420 cannot detect the wireless network card

  I scanned several times but still could not detect any wireless adapter.

  

  And then I tried to uninstall all the cards and install the last card that I had downloaded from http://www.dell.com/support/drivers/us/en/19/ServiceTag/DV1KDT1

  

  The two of them I tired to install and they have been unzipped successfully, but when I scanned the network adapters in Device Manager, even once, there is no change, all new.

  And I also got this

  When I clicked it, it became like that

  Amicodu,

  Sorry for the delay, got a little because I was absent.

  I don't see your listed wireless adapter. It may have failed or came loose. If you are under warranty, contact Dell Support tech.

  If you are not under warranty, the manual can be found HERE and go to page 45.

  Rick

• After dismantling Satellite A60 cannot detect the CD/DVD drive

  Hello

  I opened my laptop to clean-up and it was the first time that I never opened a laptop. Messed up at the opening of the cd/dvd drive.
  Instead of just pulling out, I started its opening screw but quickly realized that this is not the right way. So I took it out. Rest of the disassembly procedure went well and I assembled it back but he little silver r 2 bands and a small source, which I'm sure that belongs to the CD player and I couldn't adapt it.
  And I don't know how it fits.
  The computer does not detect the drive. Although I can open it by clicking on the Open button, then he hang out by sharp object. (The light will blink showing the power exists in)

  The second thing is the microphone. I've never used until last week, but my voice is going through. The system does not detect any microphone.

  Help appreciated

  Hello

  On this path, it is not easy to say what is the problem with CD/DVD player. Are there signs of the CD/DVD drive in Device Manager or the drive is not displayed in Windows Explorer?

  How did you test mic? Try it with the tape recorder for windows. So you can test the functionality of the mic on the easiest way.

• Satellite L300D - cannot open the ACPI ATK0100 kernel mode driver

  Hello!

  Please, I have a big problem.
  I used recovery dvd to re install vista basic.
  Since starting I have this message:

  * Cannot open ACPI ATK0100 kernel mode driver *.

  An unknown device is detected in my windows and there is no driver to install. I have no wifi detected.
  Manual installation of the driver atheros do not work!

  Please help me!

  What can I do?

  Hello!

  I never heard of this issue, but try to update the BIOS as Akuma said. It s worth a try! On the Toshiba site, you can search for an update of the BIOS:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  In the worst cases, you should try to reinstall Windows using the Toshiba recovery disc.

  Good bye

• Error message: "cannot find the wireless device" and not scan using 3 in 1 copy fax print HP 4500.

  Original title: Carpenter

  I can print but can't scan. Tried to uninstall then install the 3 in 1 copy fax printing hp 4500 but says cannot find the wireless device.

  Hi Ryan,

  You can check the link to HP support to run the HP Diagnostic Utility to check the issue of scanning:

  Find and fix common problems using tools of diagnosis HP printer=

  You can also check out the link to HP support and try to update the latest drivers/software for your printer:

  HP support

  You can also read the articles and check if it helps:

  Add or remove a scanner

  Scanning: Frequently asked questions

  The problems of scanning

• Cannot connect Windows XP to the wireless printer.

  WINDOWS XP PRINTER WI - FI CONNECTION

  I have Windows XP Media Center Service Pack 3 OS that worked a HP Photosmart Plus B209 a - m with a USB cable.  Since I just bought a new laptop (Windows 7 Professonal OS) I decided to create a home network with a router Cradlepoint MBR 900.  The two laptops (XP and 7 OSs) were connected to the internet via the router with no problems.  Windows 7 Pro OS laptop is connected wireless to the printer Photosmart Plus, I had implemented as confiquiration wireless the printer first.  But the failure of the attempt to get the OS Windows XP Media Center to connect to the wireless printer.  During the installation process to connect the printer to the XP system wireless it asked me to choose which printer I wanted to connect to.  The Photosmart Plus printer was selected and visible, then I clicked Next.  Shortly after, a small screen appeared stating the "serscan.sys" file could not be found and I have to insert a Windows XP Pro CD to get the file or run the installer of this file.  This issue has occurred both when I tried to install it with the CD provided by HP and when I tried installing the HP download website.  All I have is a recovery for Windows XP disk provided with the laptop and not a CD Windows XP Pro.  What should I do to fix this?  Thanks, Lonnie

  Thanks, that was fast.  Please, let me make sure I have this correct.  First of all, I have two recovery disks provided with the computer, with Windows XP Media Edition and one for the drivers.  I should not use either of these disks, right?  If I had the previous correct answer then let me ask the following question;  When looking to borrow the disc should be Windows XP Media Edition or can I borrow any disk of Windows XP?  Kim Merci for your help continues.  Lonnie

  Lonnie,

  Before the hunting around for friends who might have a CD, do the following research.  For each of them, make sure that you have checked the search options in the 'Advanced Options' to

  • Search system folders
  • Search for files and hidden folders
  • Search subfolders

  Search your entire hard drive and both CDs you have to serscan.  Do not include the .sys at the end of the file name.

  Search for Driver.cab.  Report of the Office (s).  On your hard disk, you should find one or both

  • C:\Windows\i386\Driver.cab
  • C:\Windows\Driver Cache\i386\driver.cab

  You can also find these files on the "recovery disk".

  Report what you find, including locations of found nothing.  It is possible (but I don't think likely) you will find a file named serscan.sy_ - If Yes, include this information in your results.

  Or, if you want to ignore all this, you can download serscan.sys since my SkyDrive-->

  https://SkyDrive.live.com/redir.aspx?CID=18b259158254905b&RESID=18B259158254905B! 225 & Thierry = 18B259158254905B! 214

  The file should go to C:\Windows\system32\dllcache (a hidden directory) and probably in C:\Windows\system32 (I do not use this file, if it is not in my system32 folder).

  Or you can just save it to your desktop and "direct the Setup" it there (if you do this, check more later to confirm that he got into C:\Windows\system32\dllcache and if not, put a copy).

• Photosmart more B209a_m: Virgin Super Hub does not connect with the wireless printer

  We recently upgraged to a new blank media 3 hub, the printer is connected to a Hp Windows Vista desktop via USB, other devices (laptops and tablets) could access the wireless printer when the computer is turned on.

  I also created the same printer to be used wireless by the other devices without the Office of marketing, it was a pain having to keep it logging on when he fell asleep. The printer had a different name if you are using one.

  After that the hub of the Virgin was installed I can is no longer using the printer without the Office being wireless, the new Center can not find the printer connects as is done before that other laptops, I had no problem with my old hub and a separate router.

  I've tried everything as suggested by Virgin (not much there) and reinstalled my drivers for the printer. Any suggestions what I can do?

  Hi @Confused_Nanna,

  Welcome to the HP Forums!

  I read your post about how you cannot connect your HP Photosmart b209 printer to your wireless network. I'm happy to discuss this issue for you!

  Please, try the steps in this guide, printer is offline (Windows) as well as this guide, the printer is not maintaining the wireless connection.

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope that this post helps!

• I had to reinstall my windows OS and now I can't connect to a wireless device, tells me that it cannot detect any wireless network hardware

  original title: Wireless help network device

  Help, please. I had to reinstall my windows OS and now I can't connect to my wireless device. When I try it tells me that it cannot detect any wireless network hardware. I am currently connected via my laptop air card. Please help me to find and correct the problem.

  Have you installed all of the correct drivers?

• C4780 cannot find the wireless router

  I have a new iMac and old Toshiba that is running Windows XP and you use a Netgear wireless router.  When I got to the printer, it worked fine on the wireless network.  Bought a new router that I couldn't work with the Mac and the PC so I returned to my original router.  Now, the printer does not work as a wireless printer.  Summaries of diagnosis indicates that the printer cannot find the wireless router and fails under "Network Name (SSID) Found."  On the Network Setup page, my network is listed as a network discovered by the printer.  I guess there is a simple solution and hope to find the answers here.

  Thank you very much!

  Some printers C4780 left the factory with a default misconfiguration.  This could be the reason why you can not see the hpsetup network.  Here is an updated set of instructions for manually adding the C4780 to a Mac:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  Press the Scan button to get the wireless settings

  Select wireless Menu

  Select wireless settings

  Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks then ShowAll bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  The printer Web page, select the network tab, and then select Wireless (802.11).  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.