Satellite P300-156 - driver detected on \Device\Ide\IdePort1 controller error

Similar Questions

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• How can I remove optical drive of the Satellite P300-156?

  Hello

  I just ordered a HD-DVD-R (Toshiba SD-L902A) for my P300-156 drive, but I don't see how I can remove my existing laptop DVD - RW drive.

  Does anyone know how this can be done without opening the case?

  Hello

  To remove the CD/DVD drive, first remove the screws of this CURIOUS.
  The screw is hidden under the keyboard.
  Therefore, you will need to remove the keyboard first.
  The keyboard is fixed with 2 screws. These screws are hidden beneath the thin plastic (door-KB)
  First, you must remove this support KB to get access to these two screws.
  After you remove the keyboard, you will find a screw that holds the ODD. Remove it and disconnecting an optical disc drive to the connector on the system board.

  But note; Be careful and all you are doing is at your own risk AND PERIL!

• Re: HARD drive need internal and business BT internal module for Satellite P300-156

  where can I buy HDD case internal and internal module for Satellite P300-156 BT?

  Try an authorized Service Center. There is a list on the Toshiba under Support site

• Satellite P300-156 won't start or by MAIL

  Hello

  I have a Satellite P300-156 I bought a few months as damaged. The screen has been damaged and the case slightly cracked. I replaced the screen and hard drive and main card seems to have no physical damage. I've been running this system for 3 months now without any problem but, today, for some reason, it won't start or even POST. It powers on and the CPU fan starts to turn then stops and does nothing. No display (I tried external). CD player works. No beeps.

  I tried reinstalling RAM even open completely and reinstalling all connections, nothing done. Does anyone have an idea what component is gone? (CPU/GPU/RAM)

  Any help would be greatly appreciated

  Thank you

  Did you update the BIOS or something?
  For me, this is a normal behavior when the BIOS chip is faulty.

• Re: Satellite P300-156: keyboard freezes touch touchpad - mic is not w

  Hello

  I installed Windows 8 on my satellite P300-156 and now I have a big problem.
  My keyboard crashes when you touch the touch pad. In addition, the microphone does not work when the Windows Device Manager indicates that it is ok.

  There is no windows driver for this laptop 8...

  There are no drivers for the laptop because it isn't win 8 supported series.
  But even if there is no Win 8 drivers, the system should not freeze affecting the touchpad module.

  However, the Synaptics touchpad driver for Win 7 or 8 to win can be downloaded from Synaptics page.
  Recommend check it out!

• Sound on Satellite P300-156 problems

  I bought a Satellite P300-156 1 year, mainly because he looked good and had Dolby Sound Room. However, I discovered not long after the purchase that he had no Dolby installed - so I tried to download the new drivers on the Toshiba site. They worked and gave me the SmartAudio app to activate the Dolby Virtual Speaker and Headphone Dolby of Dolby Sound Room. -The volume varies, as someone who has a hold on the volume dial. Not only when songs get more coins, but even just when someone speaks.

  This is crazy - and very annoying - and disappointing given the speakers harmon/kardon give amazing clarity. 3 driver updates later - still the same problem. Heard about people with the new P500 have the same problem - please does anyone have a solution? I got the problem under Vista 32 bit and now the same thing under 7 64-bit. It's a Conexant driver.

  The problem does not occur under the headphones/external speakers.

  Thank you.

  Hello

  If I understand this problem, that happened after the driver installation, and after activating the Dolby Sound Room.

  In Control Panel-> Audio Smart-> Audio second tab management, you will find a few options.
  The mode clasic has been marked.

  Uncheck this box and go to the Multi flow modes and configure it.

  I m not very well what settings you need to enable or disable because I m not P300 owner, but you should play around with these options and try different settings.

• Satellite P300 - 156 Windows 7 Crash problem

  Hello
  I have the Toshiba Satellite P300 - 156 PSPC4E, model and I've had this laptop for a couple of years now.
  Before installing windows 7, I got the default Windows Vista installed and it worked fine.
  Now since installing windows 7, no matter WHAT game I try and play just causes the cell to go black screen and turn off after about 5-10 minutes of play.
  I thought that this was due to an overheating problem... so I opened the laptop and cleaned all that and then put it back together again.
  (YES I checked all the wires are back where they should be and all the components are working properly)
  It did not work.
  Then I tried updating all my drivers and software ect.
  Still nothing.
  I searched on through pages and pages of search results for the same problems with Windows 7 and the game crashing... but nobody seems to know how to fix it.
  I thought it was just windows 7, but I re installed windows vista and it's always done the same thing on there now.
  I tried to install all the drivers of the model for this laptop toshibas site and not luck.
  My windows vista and windows 7 are two authentic copies.

  All the hardware is functioning normally (as far as im aware) and I really don't see what can cause this problem.

  If someone could give me some advice on what to do it would be greatly appreciated.

  Thank you

  Hello

  Which driver you use display? I m P300 owner but not on my A300, I had a similar problem that the laptop has crashed during a game. It seems that the reason was a 3rd party driver or let's say the driver of the manufacturing of the graphics chip directly. I think that because they are not prétestées on the cell and causing overheating

  So I recommend you to install the latest driver of display on the Toshiba site.

  Finally and above all what version of Windows 7 (32 or 64-bit), you have installed and what version of BIOS?
  From Toshiba Web site also shows the new BIOS versions and several versions 32 bit and 64 bit OS. Maybe you have to day/edit, who knows?

• Error: A parity error was detected on \Device\Ide\IdePort0 at system startup

  Original title: Windows XP error 11

  Event Viewer maintains with the following messages appears at the start of windows xp,

  The driver has detected an error of the Comptroller on \Device\Harddisk0\D.

  A parity error was detected on \Device\Ide\IdePort0.

  Hi plogmine,

  We recommend that you change the setting of firewall/security at different levels and then try to access files and folders on the network.

  See this article for more information: http://support.microsoft.com/kb/814112

  Visit our Microsoft answers feedback Forum and let us know what you think.

• ATAPI - event ID:11 - the pilot detected an error on \Device\Ide\IdePort0 controller.

  I'm getting following error in my event log Watcher:

  Log name: System
  Source: atapi
  Date: 2009-11-01 01:18:38
  Event ID: 11
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer: hendrim-PC
  Description:
  The driver has detected an error on \Device\Ide\IdePort0 controller.
  The event XML:
  
   
     
      11
      2
      0
      0 x 80000000000000
     
      53536
      System
      hendrim-PC
     
   
   
      \Device\Ide\IdePort0
      0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000
   
  

  Anyone any idea what is the cause?

  I replaced all the cables and hard drive but I get the same error (wasted money).

  When you start the PC and get "PIO MODE" in computer/manage/Device Manager / IDE ATAPI controllers ADA / ATA Chanel X/properties/Advanced is the cause, your PC is frozen.

  My "temporal" solution for this problem is:

  1 - Turn off the PC.

  2 - pick Up and the hard drive cable through the same port of the motherboard

  3. start the PC and the control in the advanced settings box-> "Ultra DMA Mode 6"; right now, you can work without problems.

  * If you can trade your motherboard (all under warranty) DO!

  -. - We are all waiting FOR you than get Microsoft a solution to force the departure to the top of "PIO MODE" to "ULTRA DMA 6"

• Windows crashes every 10 minutes for abt 30 sec / 2 min with «the pilot detected an error on \Device\Ide\IdePort0 controller»

  History/context: This problem started happening on my Dell Vostro 220, while he was new (May 09), on Windows Vista that it came preloaded with. I figured a SATA controller and a defective Dell replaced both my HD (& SATA cables) and Mobo. But ongoing problem - then Dell suggested to set access drive in AHCI mode in the BIOS. I did and in HD and installed also XP. Problem persisted. XP errors in the journal system came as '\Device\Ide' and '\Device\Hd0' sometimes sometimes. Reference Dell insists that it is a driver problem Windows. Since then, I still formatted hav clean and installed with Windows 7, what I use now. But the problem persisted.

  System:
  Dell Vostro 220 with Intel Core 2 Duo E7400 @ 2.8 Ghz, 4 GB of RAM (3 GB usable), running Windows 7 Professional 32 bit. 1 x DVD Writer TSST Corp TS - H653F ATA hard drive WDC WD2500AAJS - 75M0A0 ATA

  Symptoms:
  On bad days, it happens every 5-10 minutes; other times 30 min. Locks up system / freezes during 30 sec to 2 min during which I am able to move the mouse cursor, but do not click on anything anyone or do anything else. When Frost "thaws" if I check the Logs of error in the system log I still see the "EventID:11" error "Source: atapi ' 'driver has detected an error on \Device\Ide\IdePort0 controller. Sometimes (not always) I also see a spike in the graph of CPU use if I check right after the "thaw", but I was not able to determine what process as I am looking after the fact. Normally, there are 4 SATA Ports on the motherboard. 0.1 were used for HD, DVD. If I unhook the DVD drive altogether and connect the HD SATA cable to the port marked 2, I get the same errors, but "\Device\Ide\IdePort0" becomes "\Device\Ide\IDePort1".

  Other note (s): During the installation of the OS, Dell has a "Intel Matrix Storage" listed as critical on their site, but when I try to install it, it says "no compatible hardware not detected" and install exists.

  Also, interestingly, if I take the HD (in blue) to the total of SATA cable and try to connect SATA cable from the DVD recorder to the orange (originally) between individual ports Mobo and HD, I get a mobo error - flashing 3 light and "beep" as soon as I turn on. It disappears if I go back to blue SATA cable from the Hd for HD

  Hello

  As you have informed us that you are always faced with the question after installing Windows XP and Windows 7.

  I suspect that the problem is somewhere in the material or the SATA ports on the motherboard. I suggest you to contact the manufacturer of your computer for help, because they will be in a better position to help you.

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite P300-156 - and the button Return give the same values

  Hello

  I have a satellite P300-156, and it has a numeric keypad.
  I have problems because the Enter key and the Return key give the same values. I believe that it is incorrect.
  Can anyone help.

  Key on the numeric keypad should give an input it does.
  the Enter key on the main keyboard should give a carriage return value, but it gives an input value.

  Usually this does not cause a problem, but with software like photo shop that makes the distinction between a carriage return and a hard fall it does not work.

  Can someone help me please

  Thank you

  Hello

  To my eyes the entry and return keys are the same keys that provides the same functionality.
  I really put t know why you believe that there is something not right

  By the way; Check if you are using the latest version of the BIOS!

• Windows backup default - Eventvwr shows error on \Device\Ide\IdePort0 controller

  Hello

  I'm at my wits end. I got the error 0 x 81000037 when you run backups windows recently. I am backing up to an external USB drive.

  I went through the entire analysis point fix, I run scans antivirus complete and deleted all quarantines and I have now deleted all audio-visual products. I tried to back up selected folders, clean boots and I'm still not able to run a backup. However, I'm now not only this error code, but others.

  Looking at the event viewer, it seems that each backup error is preceded by 11 on atapi event: «the pilot detected an error on \Device\Ide\IdePort0 controller»

  I don't know what it is, but I wonder if this is what is at the origin of the problems, and if so, is this a problem with the external USB HARD drive or internal one.

  Can anyone help? I'm desperate to save my files.

  Hello

  You might face this question when the competent services for backup are not running, you can also face this question when the chipset drivers are corrupt. Make sure you don't have any other external device connected to your computer outside of the mouse and keyboard. I suggest you to make sure that the following services are running and set to automatic.

  Shadow copy volume

  • Windows backup service
  • Engine block of backup Service level
  • Windows event log
  • Task Scheduler
  • Click Start, click in the start, Search , type services.mscand then press enter and then check the benefits described above, one by one.
  • You can follow the steps in the link below and check if it helps you.
  • Windows backup or restore 0 x 80070001, 0 x 81000037 or 0 x 80070003 errors
  • http://support.Microsoft.com/kb/973455

  You can also consult the steps proposed by Stephanie Podder dated 8 June 2013 , the link given below.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/event-ID-11-source-ATAPI-the-driver-detected-a/1c45a710-596f-468C-970D-74858d0a96b6

  Let us know if you need additional help from us.

• Satellite P300-156: CD/DVD player has stopped working

  Hi people,

  I have a P300-156 and since I bought it, I had a problem with the DVD recorder... ok I know I should take that back!

  Sometimes when I press the eject button, that nothing is happening outside the orange light flashes and continues to blink. When this happens that I lose the drive in my computer and the only way to make it work again is to restart the laptop.

  Usually, it works when I reboot then stops working, but it doesn't also sometimes from the restart.

  Someone at - it ideas.

  Thank you

  Dan

  Hello!

  Have you looked on the Toshiba site for an update of the firmware? Search on the Toshiba site for an update, maybe this will solve your problem.
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  However, I think it could also be a hardware problem that your drive is defective. Then I'd go to a local ASP. A technician can check your laptop.

  Good bye