Satellite Pro 6100 - is to "restore" a re - recovery CD install?

Similar Questions

• Satellite Pro 6100 stops after 15-30 minutes

  My satellite Pro 6100 Cup after 15 to 30 minutes of operation on power outlet. There is a noise and all the lights go out except orange slow flashing (power problem). I have restore by removing the power cable and wait a while.

  It will then start again. I used two different adapters and two different batteries. It also happens if work on AC with no battery in the. My suspicion is an overheat cut-out. The Sat Pro has a? Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in. Advice much appreciated. Thank you.

  > Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in
  I agree with you and the user SambadeAmigo. It seems like a simple problem of overheating and so the laptop automatically stops to prevent the equipment from damage

  I assume that your laptop can be enabled again after being allowed to cool. It is a common question if the cooling modules may not work properly because of the dust and debris.
  As suggested, it would be possible to remove dust using the can of compressed air.
  It should work.

  See you soon

• Re: What can I do to get my Satellite Pro 6100 from the dead?

  It's now quite a few years I have a * Satellite Pro 6100 *. I recently had the following problem.

  * _Problem_ *.
  When I press the power button to turn the computer into the AC power light starts flashing orange light (flashes come in groups of eight, the second and eighth flash are longer). Nothing else happens: the computer is dead as a brick. To stop the flashing, I have to disconnect the main power supply and remove the battery.
  * + Note: the power supply is ok.

  * _Question_ *.
  What should I do to restore normal operation?

  Thank you

  Post edited by: hnav

  Hello

  I put t think you will be able to do anything that would bring back the laptop from the dead.

  According to your description books sends a flashing error code that appears always if a motherboard error has been detected.

  In your case only an ASP might help you.

  First, the technician would be able to read the code and then to know what part is malfunctioning.

  In the worst cases, the motherboard must be replaced; (and this could be a costly affair.

  Good luck

• Satellite Pro 6100 - error "password HARD drive built-in" at startup

  Hi, my laptop (Satellite Pro 6100 P4 - M 1.7 GHz/15TFT/256 MB / 40 GB/DVD-CDRW/LAN/WiFi/BT/W2K or XP) started rather recently invited me with a "Built-in HARD drive password" message at startup upward. I never put no password on the hard drive in the past, though only in desperation to try to get the laptop running, have tried all the possible passwords I have ever had. Nothing works and I'm failed with a laptop dead on my hands. I would appreciate any help/advice anyone can make.

  Thank you.

  Hi Khurram

  Unfortunately I think that you will need to replace your hard drive. If your laptop is definitely ask a HDD password then there is no way around it and the only way I know to recover from this situation is to send the hard drive to a specialised company that specialize in this kind of recovery (usually for forensic purposes, Police, armed forces, etc.). This can be very costly.

  The easier (and cheaper) option would be for you to replace the hard drive and restore your system and your data (either from a backup if you have one, or from the Toshiba recovery disks).

  Kind regards

• Where to buy drive HARD MK4019GAX for Satellite Pro 6100?

  Hi - I need a new hard drive for my satellite pro 6100, MK4019GAX part number. I have searched online but have drawn a blank. Any help would be appreciated. Thanks, Roy

  All devices, you can order from the Toshiba service partner in your country.
  As far as I know the MK4019GAX is a 40 GB ATA-100 HARD drive.
  You can also use an another 2.5 40 GB HDD.

• Satellite Pro 6100 - battery acting very strange.

  As mentioned in the title, my laptop battery is very strange.

  The symptoms are:

  When the battery is flat after only 7-10 minutes he turns not, however if the battery is removed and placed in the laptop, the laptop will start as it has never happened.
  Not only that, but the bonus after the first can indefinitely until this that loaded into an OS and immediately after starting start the laptop stops due to an apparent lack of power, when there is power always, enough to do the same thing again. Also, the battery can still start even after being just in a freezer.

  This reacondioned back to normal battery or is this safe to use battery?
  Thanks in advance!

  Hello

  I guess that your battery is old like machines of this Satellite Pro 6100 and maybe it can't be charged more. In this case, your battery should be replaced.

  But even if the battery is faulty, you should be able to use the device connected to the power adapter.
  So even if the battery is removed, you could power the unit with the mains.

• Signal not detected on Satellite Pro 6100 wireless

  I have two laptops Satellite Pro 6100, two of them are configured to automatically connect to our local wireless router which they both started.
  A computer is used by myself by my wife; bookmarks, email accounts and so on are different on every computer/hard drive.

  I have problems with one of the computers (mine) - the usual problem with multispindle connectors on the video boards and feeding, then I tried to use "his" computer with 'ma' machine's hard drive.

  His machine does not recognize our LAN with my hard drive installed. He came up with a new network found, but not a wireless network. Also, with this machine and my hard drive installed, can't the machine to search for wireless LANs, the icon does not appear. The switch is turned on for wireless signals and it works very well with his hard drive in it. The network is protected, and the two machines have the same id in them for connection which work fine in the original engine.

  I don't really understand this condition. Something in the bios? Something on my hard drive that is not recognized by the computer? the wrong phase of the Moon?
  Suggestions how to trouble shoot and fix this?

  Both machines are XP Pro on them, latest updates.

  Hello

  Also AFAIK, Satellite Pro 6100 was equipped with different Wlan cards so if use different HDD with different driver then the Wlan card could not be detected by Windows XP.

  Check if the wireless adapter is listed in the Device Manager and recognized correctly.

• Satellite Pro 6100 - how to change the date and time in the BIOS

  Hello

  I received a satellite pro 6100 that had not been used for some time. Windows does not work then he reinstalled with the good drive.

  When I try and windows 'enable', I get the error 32777 and the laptop is unable to connect with the activation servers that a google leads to believe me that the date and time are incorrect in the bios.

  I know that Press esc to access the bios but there is no option to change the date and time in there. I put the date / the correct time in windows, but this does not seem to synchronize with the bios. I've updated to the latest version of the bios, but this is not enough.

  How can I change or update the time in the bios?

  Thank you

  Hello

  I doubt this time and date setting BIOS does affect Windows activation time Windows doesn t affect it in my opinion. There must be another reason for this problem.
  You can activate Windows by phone?

  Normally the date and time in the BIOS can change you if you mark the date or time, and then press on + or - to change this. Sometimes you have to press PageDown/to the top according to the model of BIOS or laptop.
  Usually in the configuration of the BIOS you will find a brief info how changing the values.

  Check this box!

• Satellite Pro 6100 - code beep at startup

  Hi all

  Just picked up a 6100 Pro of the Satellite with a few problems.

  It lights up, he pointed out the HARD drive and I can hear the disk activity. However, the screen remains blank and a single beep can be learned after 20 sec. White screen, as I understand it, is probably the issue of Council power raging in the SP6xxx series. However, the beep I do not understand.

  I know that 2 beeps or 3 beeps is incompatibility of memory but no one knows which denotes the beep?

  Ta

  Hey Buddy,

  To be honest it's not easy to say what the cause of the problem because it could be everything and Satellite Pro 6100 is old enough for laptop.

  You have two memory modules RAM? If so remove a module. Always try a module only at the same time and test it in the slot of RAM A and B. A module is may be defective or a slot.

  If this is not the case, there seems to be a problem with the motherboard or the CPU itself. If you can exchange these things, try it yourself as a repair would be too expensive for this good old classic I think.
  Second hand spare parts you can get it on eBay s worth a try! ;)

• Is it possible to install Windows 7 on Satellite Pro 6100

  Is it possible to install windows 7 on a Toshiba Satellite pro 6100 computer? I am currently using windows XP.

  Thank you.

  Hey Buddy,

  Do you really think on installing Windows 7 over several years old Satellite Pro 6100?

  In my opinion, it won't work because it is too old and not fast enough. Newer operating system that is supported by Toshiba is Windows XP and this should be the best choice for good old classic.

  So just to be satisfied with Windows XP, it's a good choice for older computers! :)

• Satellite Pro 6100 turns off when I connect the power adapter

  Satellite pro 6100 works well up to this I put AC adapter / CC, then turns it self
  Any ideas would be appreciated

  see you soon

  Hello

  You use original Toshiba AC/DC adapter or another?
  What happens if you connect the AC/DC adapter, while the laptop is turned off?

  It s really strange problem, but I think that is s TI associated with AC/DC adapter or the motherboard itself

• Satellite Pro 6100 - no idea on I need drivers

  Hello
  Well, I brought a Satallite Pro off ebay a few days back but I can't find what I need.
  I don't have any idea what the laptop except a Satallite Pro 6100 1.7 ghz, 512 MB ram mobile P4 CPU graphics card nividia.

  It would be great if I could know what laptop that I use to download the drivers, or at least be done in which I need only one I'd love to be able to change the brightness of the display by using the fn + F5 key and have the screen filling the LCD.

  Thank you.
  Mike.

  Hello

  I put t really understand your problem

  The European driver from Toshiba site provides all the important and necessary drivers for the Satellite Pro 6100.

  I assume you mean on the XP drivers
  Install all.

  In a first step, I recommend the installation of the common Module Chip Set Utility, display driver and then continue with the rest

  If you have installed SP2 please check the "Microsoft Windows XP SP2 update information" because some tools need to be updated.

  concerning

• Satellite Pro 6100: black border to the right of the screen

  After a new installation with windows xp when I star tup I have a black border (1.5 cm) to the right of my screen.
  After the beginning and the end of the screen saver, I have a full screen.
  but when my laptop started again I have this black border again.
  I have a satellite Pro 6100.

  Management information
  System
  Model = laptop
  Manufacturer = TOSHIBA
  Serial number = 0000000000
  UUID = ffffffff-ffff-ffff-ffff-ffffffffffff
  BIOS Version = Version 1.90

  OPERATING SYSTEM
  Caption = Microsoft Windows XP Professional
  Version = 5.1.2600 Service Pack 2

  CENTRAL PROCESSING UNIT
  Index = 1
  Manufacturer = GenuineIntel
  Name = Mobile Intel (r) Pentium (r) 4 - M CPU 1.70 GHz
  Version = model 2 Stepping 7
  Max clock speed = 1694
  Socket designation = uFC - PGA Socket

  Display
  Index = 1
  Horizontal resolution = 1024
  Vertical resolution = 768
  Chip Type =
  The RAM size =

  Very strange problem! Can you please tell us more about this problem? I assume that you have installed the OS on your own. Since when you noticed this weird display problem?

  Have you noticed this immediately after installing the OS (without driver)? Did you install the display driver on Toshiba support page?

• Satellite Pro 6100 will not turn on - flashing LED

  Hello

  I have a probelem big, my Toshiba Satellite Pro 6100 lights so I decided to buy a new motherboard @ ebay.

  I have to build in and all I get is an orange error code. So I decide to make me buy a testet PCB (Powerboard) on Ebay, then the same thing! Then I bought a second Geforce but the same error code! So I all exchanged but the processor and I'm ascendant to buy a second to test or do you know Whata´s evil?
  I don't think that the new parts are broken!

  The error, the code of the orange Led is 01000011 or short, long, short, short, short, short, long, long and I did not see what maybe the problem!

  Sorry for my broken English I come from Germany!
  Hope for answers and greetings

  problemman

  Hello

  How do you know what the flashing of led said you? You are a sort of technician? How can you know that the "blink" (long, short) are 0 and 1.
  Do you know how to assemble the circuit board and don't you know that the things you have take care? Who PCB´s that you have exchanged?
  You said:

  Hand and VGA

  but the powerpcb too? And how do you know that the PCB´s are ok? Because why someone is selling you that with the 'work' of description?

  Would appreciate some feedback from you

  Welcome them

• [u] [b] Satellite pro 6100 + external projector problems [/ b] [/ u]

  Dear friends,

  I am trying to solve this problem:

  When I connect to the satellite Pro 6100 a 3rd party bCool XG1 DLP projector (a very good) I can see everything fine except DVD.

  I better explain: I can see the movies on the screen of the laptop, but nothing on the wall...

  Notice that I can look at these files directly on the screen, but on the wall...:
  MPEG files (Quick time Yes, but not WinmediaPlayer);
  AVI files (Quick time Yes, but not WinmediaPlayer);
  MOV files (Quick time Yes, but not WinmediaPlayer);

  DVD: (With Intervideo Windvd) Ok on the screen, but no output from the projector.

  Note that if I use the small window mode, the projector output image is correct except inside the window that is displayed in black (but is OK on the screen of the laptop).

  Who can help me?

  Thanks in advance.

  Stefano

  Hi Stefanohf,

  When you pass the output mode you have with keys FN and F5?

  also what settigs are set in the display driver? Right click on desktop, properties and parameters.

  go to advanced and nView. There should be active clone!

  Try this!

  Goodbye, Sam