Side Project

Similar Questions

• A second screen on the left hand side project

  I have a second monitor connected to my laptop.  The problem is that it is on the left side of the laptop.  Unfortunately, it behaves as it would be on the right side.

  Is it possible to change this behavior?
  Thank you
  Dan

  I have a second monitor connected to my laptop.  The problem is that it is on the left side of the laptop.  Unfortunately, it behaves as it would be on the right side.

  Is it possible to change this behavior?

  Thank you

  Dan

  Hi Dan

  Click on the desktop and select Screen Resolution.

  In the upper section of this window, you will see a picture of each screen with numbers.

  Position of the mouse cursor on the image on the left and it turns into a cursor "hand".

  Press and hold the left mouse button and drag the image on the opposite side of the image on the right and the release of the mouse cursor.

  Click on apply and Test results.

  Concerning

• What is the title of the highest element side of 2016?

  I have securities (table 1::B), which are labeled by year (table 1::A) and have a value in percentage (table 1::E) assigned to them.

  In table 2, I used an AVERAGEIF formula to determine the average percentage of anything with the label of 2016. I would also like to column B of table 2 to find the name of the actual title (table 1::B) whose value in higher percentage (table 1::E) for the corresponding year (table 2::A) and (table 1::A). Essentially, the question being answered is "what is the title of the highest rated power (as a percentage) issue of 2016?

  Moreover, I can then apply this same concept to get the average value of what that is a decade in particular and also list the title albums for each decade? The tricky part here is that I can simply use a direct statement because the decades are listed as 'the years 2010', "2000 years", etc. which do not appear in the table 1 original. Any ideas?

  Thanks for all the help. It's just a fun side project that I sometimes like to do and then I often learn new concepts that I can use to assess the data in my job as a teacher.

  

  Hi Minrali,

  Here is one approach. I started with 2 additional columns in the source table.

  

  F2 = MAX (OFFSET ($A$ 1, MATCH(A2,A,0) −1, 4, COUNTIF(A,A2), columns))

  If your column % is not the 4th column a you need ot change the '4' in this formula.

  It is filled to the bottom

  

  G2 = INDEX (B, MATCH(F2,E,0), column-index, area-index)

  Filled down.

  If you want to eliminate the F column that the formula would be

  INDEX (B, match (Max (offset ($A$ 1, match(a2,A,0) −1, 4, COUNTIF(A,a2), Columns)), E, 0), umn-index, the index of surface)

  He combines the two.

  

  And in fact. I would filter the table so that the years without values are hidden. Or you could wrap it in IFERROR() If you do not want to see the flags of the error.

  Quinn

• Camera USB/DirectShow is no projection in NOR-MAX

  I have a gray Chameleon Point CMLN-13S2M USB 2.0 camera and it does not appear in the NOT-MAX.

  I am well aware of Directshow registration with cameras RMP problems and I can tell the camera is correctly recorded.  It comes without any problem in AMCAP, a simple viewer of Directshow and also in Skype.

  I just uninstalled the drivers PMP and spent some time going through the registry to remove all references that I could, at Point Grey and PMP.  Then I reinstalled the 32-bit version of the newer drivers, v2.5 beta 2.  I've also upgraded the firmware of the device later.

  I am running

  LabVIEW 2012 SP1 f2, 12.0.1

  Vision development 12.1.0 module

  MAX 5.4.0f0

  NOR-IMAQ 4.7.2

  NOR-IMAQdx 4.1.0

  Any ideas?  It is a side project and I worked on it market now for over a year and I've learned to get this camera working.

  Hello

  The way list us the cameras is quite simple using the only mechanism of API Miscrosoft has for him. One thing I noticed, is that we need the "DevicePath" registry key to be filled (in addition to the key "FriendlyName"). Can you check and see if the entrance of advanced camera Grey was who? If this is not the case, try adding a string with a text for her.

  Eric

• Inter project billing - Questions

  Hello
  
  We have billing Inter installation project and the process works as expected.
  
  But we still have questions about the process of accounting - invoices for ap and ar Bill hit the same account? and how eliminate us all open on AP and AR invoices?
  
  Help, please!
  
  Thank you
  Akshaj

  Hello

  On the provider / supplier project side

  Generate revenue and transfer to GL
  Credit Internal Revenue
  Flow of unearned invoiced or income claims

  To generate and transfer to the AR Invoice (from here at GL)
  Unbilled receivables or credit unearned revenue
  Flow of internal customer accounts.

  Receive payment and apply cash to chargeback
  Credit internal customer accounts
  Debit the bank account or bank account of compensation internal

  On the receiver body / receiver side project:

  The vendor invoices accounting internal-
  Flow project supports purchased fresh interns
  Passive internal supplier credit.

  Pay the internal invoice
  Internal flow of supplier liability account
  Bank credit account or account internal Bank compensation.

  Dina

• How to connect Qosmio F750 to 2 projectors?

  I have a Qosmio F750 and 2 DLP projectors,
  a connected via RGB output and the other connected to the HDMI output via a HMDI/RGB adapter.

  I've set up the Nvidia control panel with 2 projectors with desktop across 2 projectors,
  both the value 1024 X 768. And then start windows Explorer by selecting a JPG image side by side 2048 X 768.

  The image is displayed on the screen with the two images side by side, projected from a projector, and the other projector displays the computer screen wallpaper.

  I want to display the image on the left on a projector and the other image on the other projector.
  How I set up correctly?

  Colinmeth

  I think you need some 3rd party software to do this:
  For example displayfusion
  (www.displayfusion.com)

• A more successful experience in the creation of UIs compositable configuration dialog boxes

  A few weeks I posted an experience in creating user interfaces using sub-panels transparent compositable. The approach can be described as, "It was less remarkable for being novel."

  Today, I write another attempt, this one along more traditional lines, and a lot more successful. Notable: this can be any arbitrary composition of this last AND it solved the problem of order TAB.

  This solution uses an image control and makes copies N of a control. When the user moves a control or move the mouse over the control, a real control slides in this position to be able to catch the events (updated mouse more attract State, highlight to the keyboard focus, manage typing, etc.). If the value changes, a master data table is updated and the image control is updated.

  It is something that has been tried in various forms in the past, but there are two aspects of this particular implementation that make nice:

  1. its programming interface for specifying the behavior of objects should make it fairly easy for a user of the framework generate dialog boxes programmatically
  
  
  2. It handles the problem of TAB without flickering, something I've not seen in other attempts

  This idea creates conversation about previous experience - thanks to those of you who have posted on various forums, e-mail me, or, in some cases, showed up at my office. That last is not something I am encouraging unless you work at OR... just saying. :-)

  Now, this experiement has already donnГ an interesting conversation. We note that, as long as the controls are instantiated independently of each other - in other words, any property of a control depends on the property of another control - this system of dialogue is progressing well. But in this experiment, I implemented the option button, which interact with each other - when set to True, the other false go. As soon as the controls are starting to interact with others (such as aging a control when a checkbox is disabled, or with expandable sections or really complex cases like updating a chart as a change in options, as happens in some config dialogs Express VI) then we leave who need ways to make reference to other controls. That leads us quickly in one of two directions: name the controls or creation of references. The naming approach is certainly my preference because it fits better with the data stream and I can make interesting effects with breaking apart some of the tree. But it quickly starts sounding like "Please implement a XAML parser in LabVIEW." For those of you familiar with XAML, in the world of user interface design, it could very well be the best thing since sliced bread. A XAML string would fit well with the data flow, and we could start that accumulate. I am reluctant to go down this road for two reasons. One, many have noted, it is really not a good library written in LabVIEW that can give me a useful analysis of XML DOM tree. Two, it is a huge project and my gut sense is that you need to fill a pretty big part of it before you would start to see any return on investment. But it is worth thinking to-I could be wrong. Wouldn't be the first time. This code I posted today can at least help you get started on the side of the generation if one of you decides to become laborious.

  I'll have my attention away from this project for the time being, coding in G is a lot of fun, and I wish I could spend several days to do, but this has been a side project and it is time to return to my projects assigned in the programming of text. Building a powerful platform for the automatic generation of user interface in LabVIEW would be really useful - I see a lot of requests for this sort of thing, and other languages are ahead of us in this area.

  [Last updated 17/05/2012 - there is an improved version.]

  This isn't a question. It doesn't have an answer.

• Why an asynchronous call would lead to "the VI is not executable. The full development version... »

  I built a labview moderately complex program to connect with a new parser that I build.  To briefly describe the application, the main VI is a user interface which, in an initialization step, asynchronously calls a dozen other screws each called VI is a state machine that handles communication with a component specific for my parser, whether heat controllers, regulators debit, NI DAQmx channels, a SQL database, etc..  I use the VFG and/or EI to communicate information between the main VI and each component. The system works well when it passes through NI Labview 2012 SP1 (full development Version).  I build the project successfully, but when I run the construction (on the same development machine), I encounter the "the VI is not executable.  The full development of LabVIEW version is needed to correct errors"message.

  My first troubleshooting step that was supposed to isolate the problem.  I removed all the asynchronous calls, rebuilt and the program works without errors (granted, no State machines that handle I/O bundles are running). This gave me the impression that my UI screws are not the problem.

  The next step that I took was to create a test project with a simplified user interface to call asynchronously, and control a single component.  The first part, I tried to control a heating unit, and it works perfectly.  I have build it and run without errors or problems.

  Thinking that the component should not be a problem, I add the async call for this component in my main VI, to test it.  This works well in the built environment of Labview development, without errors, but alas, I get the same message as the "VI is not executable' when I try to run the build.

  I am at a loss on how to make trouble, or it could be the cause of the problem.  Why an asynchronous call to the VI even break the construction of an executable project, but don't cause problems in an executable of side projects?

  
  

• Problems with deployment of network shared on windows PC when installing INSTALLER variables

  Hello

  I'm using LabVIEW 2014 on Windows 7. I have a project that is developed to be a client GUI (192.168.1.208). The GUI communicates with an application of RT (192.168.1.206) running on LV RT OS and both are connected to a network. The NSV (shared network variables) are housed next to the RT (SVs is on RT/demand side project). This part (communication and everything) works very well.

  Now another part is recording data. Why NSV (hosted in the GUI project) are used for strings of communincate (events with the data) to a computer running the registration of data on this PC (192.168.1.208) server. Please note here, currently same PC (192.168.1.208) was used for recording the data server implementation, but later, there may be a new PC that's why NSV is used. I gave this information in case there may be no problem (chances are though).

  

  I created an application (*.exe) and the project GUI installation program. Saving data to the PC (192.168.1.208) if I use one of the options-project/*.exe/installer works supposed. but when I try to install this Setup program on another PC on the network which has no service OR installed gives following error during installation:

  Deployment deployment failed shared Variables.lvlib\\192.168.1.109\Shared Variables (error:-1967362042, operating system and Network Services: (Hex 0x8ABC7006) could not start service.).

  I have tried almost all the variations in the construction of Installer and .exe for it, but couldn't get rid of this error.

  I also want to know how would be a PC not having not OR services/programs installed would host OR shared Variable engine. Although application of the runtime in the application, we give option while building the .exe. But not for the EVS.

  I lost several weeks on this issue of emergency assistance would be much appreciated.

  Thank you.

  If you uncheck the option "selection auto installers" in installer build specification, it should give you the full list of installers, you can include. It's a little weird that it has not detected the requirement of NSV, however.

  I think you make you life difficult for yourself by trying to do a few odd handshakes with strings/NSV - NSV is 'tag' data - they are good for the reading of the last value of a variable/signal. If you want to send messages around - stream, network - there is even something like reference e-mail Simple (STM) library - http://www.ni.com/example/27739/en/

• Trial options for Windows?

  I'm looking to build a pc as a side project that I'll probably sell it after the fact. I was wondering if there was a windows version that can be installed for a trial of only 30 days so that I can test the PC and then when someone buys it prompts you to buy a full license after the period.

  I see a lot of workstations sold with 30-day trial of windows 7. Not sure if there are legitimate or not.

  I wish I could sell the computer with a trial version of windows on that the user must activate later if they choose to keep the windows.

  Any info is appreciated.

  http://www.Microsoft.com/en-us/software-download/Windows10

  https://www.Microsoft.com/en-us/software-download/techbench

  I would use the techbench URL, because it lets you choose which version (home, pro, etc.)

• AutoPlay questions with a USB non-volume device which is regarded as a com port virtual using a chipset LPC2468 IAR.

  I'm working on setting up autoplay to open our software on your computer when the USB connection for a new product, we are about to launch. I can get the AutoPlay dialog box appears, but it is empty.  He considers the virtual device as a com port.

  I added the device in DeviceHandlers, added arrival in EventHandlers, added the device in managers, so on and so forth in the msdn library to speak... Yet when I plug it in, I get an empty auto play dialog box, and the icon at the bottom right is a generic icon.

  What else in the registry I could miss so that XP recognize the device and allow an automatic start of the software updated?

  I am all that as a side project as a TSR, because I think that this feature would make my job easier. Unfortunately the engineers working on the device itself doesn't have much time to help.  I am familiar with editing the registry, but not very thorough. I searched and searched online and tried many "bugs" but nothing seems to get the box unblank. If the autorun.inf is generic or missing, it causes this problem?

  Thanks in advance.

  Hello

  As you work on the development of software for USB connections, I recommend you post this question in the MSDN Forums.
  http://social.msdn.Microsoft.com/forums/en-us/categories

• Is there a successor to the BlackBerry Java platform?

  Hello.

  It's been a while since RIM announced that API Java only be supported in BB10. Since then, they have released software development kits for:

  • SDK native (C/C++) and waterfalls (C + c++ / Qt)
  • HTML5 Webworks
  • Adobe AIR
  • Runtime Android

  So, what would be the most similar to the current Java API platform for BB10? I think about things like:

  • Camera
  • NFC
  • Bluetooth
  • SQLite
  • A GUI Framework (screens, components, etc.)
  • Autorun at startup, background applications feature
  • GPS (listeners, geofencing)

  Thanks in advance.

  RIM seems focused on the main platform being the NDK + waterfalls.

  Adobe Air seems to be the red headed daughter-in-law who is left behind.

  Android is the popular kid they keep around to look at more cost.

  WebWorks seems to be more than a side project.

  So yes, go with the NDK.

• $ paid for Converter AMR - NB (in raw or PCM)

  I need raw audio data and many BlackBerry phones do not support PCM.  I'm working on that as a side project, but I'm willing to pay for the labour code.  Prefer the code that supports the JDE 4.2.1 and later versions.

  Contact by e-mail if you are interested.

  [email protected]

  Thanks for the advice guys...

  I'm not in real time so I will not push so far, but a user can record 30 seconds of audio and wait 30 seconds for a response from this point is really annoying.  So far I have cut about 30% of the time by not a "perfect" decode (I'm data analysis does not return then it does not sound right there just reflect the amplitude and the time of the original database). "."

• What to choose? Samsung 850 pro or Photoshop pro 950 m2.

  I'm going to build my new PC, and the focus is Adobe Photoshop and Adobe Illustrator. I on side projects such as Cinema4D, Adobe Premiere and After effects. It will be a processor 6800K, a GTX 1070 (for some extra fun in spare time) and 32 GB of memory.

  I'm still nog certain to do the 850 or 950 m2 pro pro for my OS and programs.

  On paper and in the benchmarks, the 950 pro is destroying every SSD out there. But the downside is the Heath and the price.

  Second and this is my main question... you will see the difference between the 950 pro and the 850 pro when you make large files. For example, I was working in a digital painting 14FR. It's a spectacular size that would be printed for large windows. It was horrible to work in this file and it took me a lot of extra time, waiting on the computer.

  -What is the 950 pro worth his money or doe that speed up my work in just a few seconds?

  I hope someone can help out me.

  Roy

  When you work with large files, you must make sure that there is no I/O bottlenecks anywhere. In other words, you need a balanced system. I don't know what an SSD marginally more fast, by itself, will make much difference.

  First of all you need of enough RAM (32-128 GB) and a record of effective working configuration. If your system SSD has sufficient free capacity - and you need a lot for these filesizes, 100-150 GB at least - the fastest configuration is to have scratches on your system disk. With spinning disks, it is advisable to have zero on a separate disk.

  If you want maximum speed of I/O you might consider RAIDing two or more SSD, but then you must also have a separate RAID controller. Not sure if it is worth.

  FWIW, I have a 500 GB 850 as my system disk, using an i7-3820 and 32 GB of RAM. It works well for large files, I regularly work on the panos of 30 000 pixels or so without any problem. However, I would like to make a separate 240GB SSD set up for scratch, mainly to avoid wear on the system drive.

• Suggestions for work as a Cloud Eloqua partner?

  Hi all

  I'm working on a side project with a company that will develop a cloud connector Eloqua in the end. I've always been on the client side of things with Eloqua, so I'm not sure I know what I don't know. Suggestions, stories, comments or warnings for me? The product is powered, we are at the point we are assessing which businesses to integrate and then go that route.

  LMK what you think.

  Dave

  Hey dliloia , I have a few takeaway that I can share with by phone if you wish. I had an experience with a couple of different partners. Would be happy to talk. There's a PM with your email and we can get back on the phone.