Simulation of the LCD

Similar Questions

• How can implement you not with Tim Capsule and AirPort their simulation on the iMac?

  Hello

  How can implement you not with Time Capsule and AirPort their simulation on the iMac?

  I don't know what you're asking.

  AirPort Extreme is a wireless router.

  A Time Capsule airport is an AirPort Extreme with a built-in hard drive for data storage.

  An iMac is a Mac computer.

  An iMac is not a wireless router, so he is unable to perform the functions of a wireless router.

• How much will cost to repair the glass and the LCD to an iPhone component damaged 6 in the Apple Store?

  My partner has dropped his iPhone 6, visibly cracked glass and damage the LCD behind (distorted lines). How much will cost to get the two components repaired in-store? And this is something that can be done on the spot?

  Much obliged,

  KJH.

  See iPhone pricing of Service - Apple support (change the country in the lower corner on the right if you're not in the United States)

• Tecra S1: Notebook generates noise when the LCD display is on

  Tecra S1 is 4 years old and generates a high noise when the LCD is turned on (from last week). The noise comes most of the keyboard. Could this be a defunct ups?

  Is there an easy way to fix it? It's not very loud, but in a quiet that is audible.

  Hmmm I think this noise comes certainly from the FL inverter.
  But I can't tell if the inverter is faulty or not because I noticed that her top on different laptops when the brightness of the display is placed on the lower floor.

  But if you think that this problem was not present in the past, then you need to contact a technician who could help you replace the inverter FL.

  Best regards

• Satellite M70-309: how to clean the LCD?

  Hello world!

  I have Satellite M70-309, so how do I clean finger LCD, dust, ecc... ?

  Thank you!

  Hello Rocco,

  Usually mine clean with a slightly damp cloth (wipe softly on the surface) and then just dry with a cloth. This command removes all the dust and finger marks.

  I also used a normal domestic surface cleaning spray (used sparingly) applied with a cloth and this removes any greasy fingerprints that can be on the screen.

  It is very important to not to use cleansers, abrasives or solvents as they may damage the surface of the LCD screen.

  Kind regards

• Tecra 9000 - no display on the LCD screen when you turn on

  I recently got a Tecra 9000 for cheap on eBay. I am experienced with the construction and repair of computers, but not so with laptops.

  The problem with this laptop, it's that do not display on the LCD screen when you turn on. It was just black, no backlight, nothing. I took the laptop all share, found no obvious problem. I had to turn it on and the screen lights up a few times trying to figure out the problem. Would it be a bad connection? Or something else?

  After getting it to start work, I'll try to start to put it back together and it stopped working again. I haven't not been able to reduce it to know if it's a bad connection or a card problem.

  Someone at - it suggestions? This is a problem for others here?

  As you describe the issue, I think it is somehow a bad connection or a damaged cable, because it does not work once you have disassembled the screen.
  Maybe you need to check all the cables, leading motherboard to the LCD and take a close look, maybe for a few scratches or strong curvature.

• Qosmio F20-155: how to clean the LCD screen?

  How can I clean the LCD qosmio f20-155

  Hello

  Check this post on the same topic:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=14642

• Brightness of the LCD in the BIOS

  I would like to know which of available Toshiba laptops currently would allow me to set the LCD brightness level directly in the BIOS.

  Hello
  I don't think this is possible, but if you are on windows, there is a way to change the default brightness. It is closely related to the "modes of energy toshiba".

• Satellite A100 - display balack after replacing the LCD screen

  Hello

  So I'm trying to fix a LCD on a Satellite A100. The girl I am set as said she accidentally hit the screen with his hand and became black.

  When you turn on the laptop I can here windows activate, nothing is on the LCD screen. It is not the backlight, because I don't see anything on the screen at all. So I bought a replacement LCD screen and that one does not work either. Same question

  I think it is the inverter, any suggestions?

  Could be the sensor cover?

  Thank you! Kyle

  Hi Kyle,.

  Did you buy this new LCD screen to a service provider authorized? I ask this question because it would be interesting to know if it s a Toshiba valid a party or 3rd party a spare.

  Did you check the connection of the LCD cable? There may be a link to lose or the cable itself is touched.
  Theoretically, it might be the FL inverter too, but I doubt that. Otherwise, you'd see something on the screen but very dark.

• Satellite M60-104 - vertical lines on the LCD

  Hello guys,.

  I have a Toshiba Satellite M60-104 and in recent months, I noticed vertical lines on the LCD screen. How can I solve the problem?

  Any response will be useful,

  thanx

  Hello

  First of all, you should check if you have the same problem on an external monitor. So you can check if the problem is the graphics card or screen.

  However, I think that the motherboard or display needs to be replaced. To do this, you can go to an authorized service provider.

  Welcome them

• I can not put the correct date, time, or whatever it is on the LCD on my HANDYCAM DCR-HC30

  I had not used my cHandycam for quite awhile for the date and the time is shown in the January 1, 2004, at 12: 00 and I was not able to change using the LCD screen. I'm fairly certain that the remote control battery is no good because I never changed it. The camera still records both Ribbon and the memory card, but I would like to be able to set the date and time. Has anyone else had the same problem with this Handycam or know how to fix. I charge the internal battery by pluging in there for more than 24 hours. The internal battery is bad and if so, is it replaceable by me? Thank you.

  If you can access the MENU of the Handycam, please follow the steps below to set the date and time.

  1. turn on your camcorder and open the LCD.

  2. press on P-MENU then MENU.

  3. Select CLOCK SET by pressing the HIGH or arrow DOWN found at the upper and lower part of the screen, then press OK in the lower right corner.

  4 set the YEAR by pressing the HIGH or DOWN arrow found at top and bottom of the screen, and then tap OK in the lower right. Follow the same procedure with the MONTH, DAY, HOUR and MINUTE, and then tap OK.

  NOTE: To midnight, set at 12:00 AM. For lunch, set for 12:00

  You can also view page 22 operations here Guide: https://docs.sony.com/release/DCRHC30.pdf

  If my post answered your question, please mark it as "accept as a Solution.

• Pavilion dv7 - 1228ca: how to order the LCD backlight for hp pavilion dv7 - 1228ca

  Hello, could someone to give advice how control the backlight of the LCD screen for hp pavilion dv7 - 1228 ca?

  Thank you.

  Hello

  Unfortunately, the machine is too old, not parts available:

  http://PartSurfer.HP.com/search.aspx?SearchText=NB238UA

  Please use the part number on the list and the search on eBay or other online stores.

  Good luck.

• How can I disable auto switching between the LCD screen and the viewfinder electronic on Sony A7sii?

  Hi guys,.

  I don't have it if the table on the right, but here's my question...

  Disabling automatic switching between the lcd and the viewfinder on the Sony A7Sii?

  Thanks in advance,

  Zia

  Hi @dslrshooters,

  could you please change your message header to match the content of you post.

  in the A6300, you can change the way in which the camera automatically switches between NET & screen in

  Menu custom (cog symbol): FINDER/MONITOR.

  with a little luck, you have the same menu on the 7Sii.

• Gigaframe L81 - after 2-3 seconds, the LCD screen turns off

  Hello!

  I think, I missconfigurated my camera... I put the automatic light (auto light) options, then the LCD is turned off. OK, its light of day here, but how can she Cook?

  And - perhaps because of the thing said? -its LCD screen turns off every time, when I push the power on button. I'm tired of using the reset switch, but she has - at least, in the LCD - no effect.

  Device is reset, then lights up the screen, I see him starting, I can touch control "buttons" on the right side (I can see the blue lights), but after only 2-3 seconds, the LCD display turns off again.

  Although I can do anything on my camera - attach PC files, copy or dele (ordered from Windows) etc. I just don't see anything in the LCD screen.

  What's wrong?

  If it still does not work after resetting it, then it may be a hardware problem.

  I think that you will need for repair/replacement.

• Re: Replace the LCD Satellite A505-S6960

  Hello

  I bought a replacement LCD screen for my satellite a505-s6960.
  I can't pull the old a.
  I unscrewed several screws on the bezel.
  However, I can't get out of the bezel.

  Any ideas?

  Take a look at irisvista.com. you will find information how to remove the LCD screen. Perhaps, you will find something useful

  See you soon