SMALL BUSINESS SWITCH SLM 2024

Similar Questions

• Problems with config Small Business switch

  Hi, I know that if I read the documentation I will come for answers, but I'd really like some input from someone with more knowledge than me. I have a problem with Cisco SF300, one of the Small Business switches. I have a single interface on my router and I need to separate my internal networks, I thought that one way would be to use VLANs. On my two internal networks a network has D-Link unmanaged switches, the other has the Cisco SF300 I did as follows.

  On the Cisco Switch, all of the default ports for ports of junction. I changed FE1-FE24 and GE1-2 to access ports.

  Created two VLAN and placed FE1-FE24 in VLAN10 (also my management VLAN), GE3 is a trunk Port for unidentified VLAN20, VLAN 20 uplinks to my DiLink switches. This way my unmanaged switches traffic arrives on a trunk on VLAN20 untagged port.

  GE4 is a trunk port and I assigned to VLAN1 untagged, tag VLAN10 VLAN20 tag and. 10 of VLANS and VLAN 20 then to my router.

  The plan was to connect GE4 to my router, but I had two things happen that I can't explain.

  All first as soon as I connected my D-Link to GE3 LAN on VLAN20 came down, I couldn't ping servers from computers etc, all devices are connected to the D-links unmanaged. Secondly, the responsibilities of VLAN changed on GE3 GE4, VLAN 10 and 20 disappeared and only the VLAN by default was assigned, also under settings VLAN my state of interface VLAN for VLAN20 shows people with reduced mobility. One of my FE12 continues also to change VLAN access ports.

  Can anyone offer any suggestions as to what might have crushed the LAN and why change my VLAN. I wrote my config running at startup configuration incidentally.

  I added two screenshots.

  Seriously, I'd appreciate the help.

  Thank you

  Bob

  Hi Bob,

  Could you please post a topology? I can help with this, but it would be much easier that I could see your network.

  Thanks in advance,

  Garrett

• Small business switches and POODLE

  Cisco did research in small business switches being vulnerable to POODLE?  I know they are working hard on the side of the business, but I'm not finding any information on the side of small business.

  Hello

  All Cisco products will be checked and the results are displayed on the same page for the company:

  http://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CIS...

  Kind regards

  Aleksandra

• Fundamental issues of SFP for Small Business Switches

  Hi all

  Just for fun, I would switch to fiber, running the trunk ports between my two Cisco SG300 lab switches but I'm new to the media.

  In looking at the options, I thought that MM (MGBSX1) is the way to go, but the cost of the 'Official' FPS an arm and a leg. (don't forget, he is my laboratory, not a production environment).

  I have a few newbie questions and forgive if this has been answered a hundred times, but I was not able to find in the search.

  1. What I really need to use Cisco brand trancievers? I've seen other than Cisco 1000BASE-SX SFP on ebay for a tenth of the cost. Given that, Yes, the quality may or may not be the same.
  2. Is MGBSX1 way to go? Switches are in different rooms, so distance is not a problem, my choice was based on cost trancievers and media.
  3. SFP ports are valued only Gigabit, but I saw a higher number variety quoted. Is this a limitation of the switch itself, the protocol used, or the transmission media?

  Again sorry if these are questions of newb and thanks in advance!

  Lee

  1. should I really use Cisco brand trancievers? I've seen other than Cisco 1000BASE-SX SFP on ebay for a tenth of the cost. Given that, Yes, the quality may or may not be the same.

  According to the Quick Start Guide SG300 ' SFP ports are compatible with Cisco modules MGBT1, MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFELX1, and MFEBX1, in addition to the modules from other brands. "

  2. is MGBSX1 way to go? Switches are in different rooms, so distance is not a problem, my choice was based on cost trancievers and media.

  Choose a type of SFP based on the length of the links and the type of available fiber.  Small Business card SFP provides the information you need.  The MGBSX1 is probably a good choice, low-cost, up to length of 550 meters over multimode fiber link.

  3 ports SFP are valued only Gigabit, but I saw a higher number variety quoted. Is this a limitation of the switch itself, the protocol used, or the transmission media?

  Each switch is designed to support specific port speeds, based on the application of switches designed into the network.  Optical transceiver modules do not support different speeds (like many electric ports).  Instead, the switch port is compatible, the transmitter/receiver module can be swapped to change speeds.  Style SFP modules are available at 100 Mbps and 1Gpbs; Modules of SFP + for 10 Gbit/s; higher speeds have new form factors.  You can see a lot of styles of optical Modules on the page Web Cisco transceiver.

  Good luck!

• Plug-and-Play for Cisco Small Business 300 Series managed switch

  Nice day

  What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?

  It seems there are not, the operating system is not the standard IOS I used to.

  I would use with ability to bridge the Infrastructure first Cisco PnP.

  Concerning

  Stone

  First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.

  Seal a document shows how this is done.

  Hope that the information would be useful.

• Configuration of SNMP on Cisco Small Business 300 Series managed switch

  Please can someone help me configure SNMP on Cisco Small Business 300 series switch?

  Thank you

  Hi Anton,.

  Don't forget to activate the service SNMP is first of all: Security > Services TCP/UDP.

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=3b13278d9ef9402a8fef57...

  also, you will find useful documents for configuration etc on our server community kb:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=183cae2148d445b2a07473...

  Let us know if you have any problems.

  Aleksandra

• Management tool for small business series switches

  We currently use CatTools for our infrastructure management systems; However, it does not support small business of switches of the series (IE SG300 & SG500). I am looking for a free/no expensive replacement. Any suggestions?

  Looks like CatTools can work with some adjustments.

  https://thwack.SolarWinds.com/thread/64196

• My small business SF 302-08 Switch will not let me apply the command "Routing".

  Hi everyone, my switch cisco small business SF 302-08 has the latest firmware and I want to activate the command routing, but it doesn't let me do that.

  I've read the reference guide for orders, do all this procedure: IP Routing Protocol independent commands starting at page 629, but nothing happens. I need this because I want a routing between VLANs

  Kind regards.

  Hi Felipe

  Look forward to hearing how you go.

  If you reset the factory default switch and the switch is NOT connected to a server, the switch restarts with a default IP 192.168.1.245 address according to the Quick start guide .  If your PC has a static address 192.168.1.2, you should be able to access the graphical interface of the switch.

  http://www.Cisco.com/en/us/docs/switches/LAN/CSBMs/sf30x_sg30x/Quick_Start/78-19252-01.PDF

  If the switch is connected to a DHCP server, the switch Gets an IP via DHCP.

  I've had problems using hyperterminal on my Windows 7 box, that I have overcome by restarting my PC in order to free the COM port.  Settings of the console are;

  • 115200 bits per second
  • 8 data bits
  • no parity
  • 1 stop bit
  • no flow control

  If you really have problems, and you think that the switch is faulty, you have the possibility to use the services of small business Support Center (HWC) in order to identify if the switch is good or bad.

  The URL that watch phone numbers are lower;

  www.Cisco.com/go/SBSC

  Best regards, Dave

• Windows Small Business Server 2011 - "windows setup cannot continue because a required driver could not be installed.

  Hello

  I try to install windows server enterprise on my hp proliant gen 8. I used smart supply and that everything was working fine, when switching to the windows installation it gets to 99% then comes up with the error:

  Windows Setup cannot continue because a required driver could not be installed

  I was wondering what I can do to solve this problem, I have tried several times without success. Thank you for your time.

  Hello

  Your Question is beyond the scope of this community.

  I suggest that repost you your question in the Forums of SBS.

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver

  "Windows Small Business Server 2011 Essentials online help"

  https://msdn.Microsoft.com/en-us/library/home-client.aspx

  See you soon.

• You need to add a 3rd WAP to existing small business network. Where I start?

  The network has 26 ports Cisco switch and 2 existing WAPs, 1 of which is an air 1040, and the other I'm not sure but it resembles that of other.  I need to add a 3rd WAP for a small room.  I was going to use an other cisco 1040 air, but I don't know where to start.  There is a smaller, lighter WAP that works?  I have no experience in network configuration, so I'd like something simple.  Help, please.

  Thank you

  Laura

  Hello Laura

  My name is Eric Moyers, one of the Experts I wireless in the Small Business Support Center.

  Normally, I tell customer to add products similar to their outgoing network when they're trying to develop it. This prevents the learning curves to a minimum and help in getting enlargement and running faster. However, there are time going with brand new products are better, especially if you are trying to integrate the best technologies.

  The Aironet 1040 currently being End of Life / end of sale. You would need to look for a different model.

  He stay with the Enterprise Access Points level, the AIR 1602 has the same capabilitoes as the 104 you're too used. Price range is 300 above low 400 according to one where you look.

  If you want to look at small businesses, we have the WAP561 which is also dual Radio and should do everything the 1040 can or you can look at the WAP371 that is double also but includes a radio that can make the new signal "AC". These two serve 200 upper middle 200 depending on where you look. By the way that they look almost identical to the AIR1040 as well.

  I hope this can help you started, please let me know if I can answer anythin else or go deeper.

  Eric Moyers
  .:|:.:|:. CISCO | Eric Moyers | Cisco technical support |
  Wireless and monitoring subject matter Expert

  Please note useful messages and let others know when your Question has been answered

  You can click on my name next to the image if you want to email me directly

• Accounting on a Cisco Small Business SF300-08

  Hello

  "Cisco Small Business 300 Series managed switches Administration Guide" and the sheet indicate that this switch can make requests of accounting with a Radius server. On the switch interface/CLI SF300, there is that the authentication port, the port of account cannot be resolved (and nothing is sent by the switch to the default port). I guess that the SF300-08 doesn't manage accounting. Maybe I need to change to another model. Could you give me another model in the same price range?

  Thank you

  Laurent.

  Hi Laurent, I am pleased that the 1.2.5.70 has solved this problem.

  Please keep Advisory of the 1.2.5.70 firmware has also been lifted for now.

  Please note that we have identified a potential problem with the 1.2.5.70 update for the series 200, 300 and 500 switches. As a precaution, we took down the 1.2.5.70 free while we determine the cause of the issue, the seriousness and the scope. We re - ask the release or publish an updated based on the results of our analysis.

• Small Business Investment program Question

  I have a question about the small business investment program. I just bought a Cisco Small Business router and additional Small Business 8 Port Switch. Later on the road, we might need a 16, Port or more, but we don't need to exchange any now. We wonder what it takes just to enroll in the program. What is the link you need to register?

  http://ciscoinvestmentprotection.com/register.html

  Thank you!

  Hi Nathan,

  I just noticed that you also tweeted on the subject.  Anyway, here's the URL that you should go and look for information about this program:

  http://ciscoinvestmentprotection.com/brochure.html#

  Kind regards

  Cindy Toy

  Cisco Small Business Community Manager

  for Cisco Small Business products

  www.Cisco.com/go/smallbizsupport

• Small Business VPN

  The ultimate goal is to be able to access my intranet in my small business from a remote location. When I'm at the store, I can access the network through 'My computer' and see my network printer and files stored on the server. I want to be able to access this network from remote locations in order to then print in my store and work on projects that I recorded on my server. I work from my laptop to the home school, various locations, Hotels, etc. then what I understand will continue to change my IP address. If I am not mistaken, this means I have to start a VPN and open a DMZ. If anyone else knows how differently, please let me know.

  I set up a virtual private network to my store on my work computer and set up on my laptop using the VPN Wizard in windows. But I'm short the problems getting through my router. I have Windows Vista Business on my work PC and windows home 7 on my laptop. The internet in router Belkin F9K1102 v1000 before going to my work computer and goes through an Actiontec GT701-WG gateway. Belkin support sent me the instructions to turn the DMZ and define virtual server ports. I think I have about this law, still trying to figure out the incoming port information they gave me because it has been translated into English by a computer program. They said four inbound ports allow and then gave me a bunch of numbers:

  TCP 1723 PPTP 443 SSL 10000

  UDP 1701 L2TP, 500, 50 & 51

  Written just like that in the email. I recognize the TCP and UPD, just use the 1723 and 1701 and what are the rest of the numbers? Do I need to set up a DMZ on the bridge too? Any help would be appreciated.

  The native PPTP VPN server on the Vista desktop needs than the TCP 1723 Port forwarded. Close the other ports. It said that there are also protocol 47 GRE traffic to pass through any firewall/router that VPN server is behind. Some barrier-lights/routers call Pass Through PPTP or VPN Pass Through or as the pass of Windows Firewall that automatically if the TCP 1723 Port is open. This page has troubleshooting at the end.

  http://theillustratednetwork.MVPs.org/Vista/PPTP/PPTPVPN.html

  If any firewall/router does not pass the GRE protocol 47 traffic, you must replace the device or switch to a newer firmware to fix the problem.

  Affecting the VPN server in the DMZ, he exhibited to the public internet. Normally I should not do so because of security risks.

  An alternative might be to use the function of TeamViewer VPN. TeamViewer note is NOT free if used for commercial use.

  http://www.TeamViewer.com

• T200v server with Windows Small Business SERVER 2003

  Just ordered a server TS200v, can I install Windows Small Business SERVER 2003 on this server, or do I have to upgrade to Windows SBS 2008?

  Hello

  SBS2003 is not officially supported, I think that 2008 alone is. You can try but might be a problem with some drivers.

  J.

• Windows Small Business Server 2011 Standard access to download

  Hello

  I need to access a copy of the Small Business Server 2011 Standard edition since the MSDN site, in order to help one of my clients.

  They have SBS 2011 standard installed on their network and I'm going to make some big changes to their network. To do this I need to access the installation (file ISO DVD) on MSDN disc. They have the product key, but not the original disks that were used to install SBS 2011 Std.

  Thank you for your help.

  Hello

  Your Question is beyond the scope of this community.

  I suggest that repost you your question in the Forums of SBS.

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver

  "Windows Small Business Server 2011 Essentials online help"

  https://msdn.Microsoft.com/en-us/library/home-client.aspx

  See you soon.