Sony Str - Dn 1040 Dolby True HD

Similar Questions

• Sony STR-DN1040 receiver help

  I have a Sony STR-DN1040 receiver. I have my PC connected to the receiver and I can not get sound when I have an optical cable connected to my receiver. I have the cable plugged into OPT1 and cable HDMI plugged into Video 1 (note: my PC sends no audio through the HDMI, so I have to use the optical audio input). I got this Setup on my previous Onkyo receiver and everything worked perfectly. I have not changed the PC settings so everything on this end should always be configured correctly. Any help would be appreciated.

  Thank you

  Andy

  You can reassign the DIGITAL to other entries input jacks, if the default settings of the sockets do not match your own equipment.  The default assignment of OPT1 (where you plugged in your PC) is SAT/CATV and which could be the reason why there is no audio coming out of your receiver, even if the PC is out the digital signal.

  

  Try to set OPT1 to VIDEO1 under [A. ASSIGN] assignment of digital audio menu. Follow the steps below

  1 press AMP MENU

  The menu is displayed on the notice board of the receiver.

  2 go all the way to Input settings]]

  3 select digital audio input assignment [A. ASSIGN]

  4 the value OPT1 VIDEO 1

  See page 86 to 87 of the manual provided for more information on the assignable audio input jacks.

  If this post answers your question, click on "accept as a Solution.

• Capabilities of the STR DN 1040 amplifier box.

  Can you control the volume separately with an amplifier STR DN 1040?

  Yes, you can control the volume separately when you use the multizone function. For example, if the has / V receiver is in Zone 2, all changes will be applied to the current zone only and should not affect the other area that is not active.

• Add Wireless for SONY STR-DG510 receiver speakers

  I have a SONY STR-DG510 receiver. It has 3 speakers (right, left & Center) connected now.

  I would like to add two speakers more to it. The outputs are available on the receiver, but I don't

  not like the idea of the wires running in all directions.

  I thought using a wireless speaker I could at least eliminate the wires of the receiver.

  Any suggestions on what to use? Most of the things I find is oriented towards computers or cell

  Phones.

  Thanks for your suggestions

  RS

  I thought that this kind of, but hoped someone could tell me

  something that will work.

  RS

• Sound of television through Sony STR-DH130 receiver

  I recently bought a receiver SONY STR-DH130.  As with my previous receiver (an old Kenwood 3090) I have connected it to the top so that the sound of my SONY's Trinitron TV through the receiver to separate the speakers.  However, unlike with my Kenwood 3090, I can't control the volume separately to the speakers.  I can only control the volume of the receiver speakers via switch on the satellite to the receiver.  The sound of the television is stronger than my receiver speakers and smother them.  Therefore, I don't get a good stereo separation.  With my Kenwood 3090, I could put the TV on mute and listen to the sound of the TV through my receiver speakers (which are much better).  Any way to do cela with the SONY STR-DH130.

  Thanks in advance

  Bookman

  If your audio connection cords catch AUDIO OUT of the Sony KV24FV12 TV to the AUDIO IN ports of your STR-DH130 A / V receiver then you can turn off the TV speaker, AUDIO OUT option FIXED value so that you can adjust the volume of the TV via the remote control of your receiver. (see pages 19 and 20 of the TV Manual)

• Issue of Sony STR - DN1040 output HDMI Samsung UN60F8000BFXZA TV

  Hello community of Sony,

  I have a question of a Samsung UN60F8000BFXZA TV HDMI Sony STR-DN1040 output.  I have a cable Xfinity RNG110 box and a Samsung Blue Ray BD-F5900 connected via HDMI 1.4 cables I have HDMI 1.4 cables connecting all devices.  I had the GeekSquad install TV and set up the Sony A / V receiver.  Everththing was working fine.  I turned off the system for a few hours and came back and turned on everything.  Initial configuration is A / V HDMI's out to TV input HDMI3.  HDMI input and output supports CRA.  The TV would constantly check your connection to the device.  No video just a black screen.  Power cycle sometimes or reinstall the cables could clarify the issue.  Same problem you select, the cable box or the player blue ray, as input device...  I swapped the HDMI cable from the upper area of the rec AV cable and the cable to the AV rec on television.  No change in symptoms.  I even hooked up the TV to the AV HDMI B outupt with no change in symptoms.  I directly connect the cable box to TV without problems.  I get video every time.  I'm afraid I see many messages from simular 'video problem' on the receiver AV STR-DN1040.  The two TV and AV receiver have been purchased this week.  What should be the next steps?  I have the Geek Squad back to verify that I may have a problem of AV receiver.

  Cheers, Oakleyrider

  
  

• need manual for vintage sony STR-6045

  I need the manual for a str-6045

  I need the manual for a str-6045

• 2 questions about Sony STR DN1030

  First of all, how can I activate AirPlay without turning on the TV at the same time? I have a Sony's Bravia TV. I tried to change the HDMI settings but did not understand right now.

  Secondly, one of the reasons why I bought this unit was because it supports the reading of Zone 2. I called Sony to ask about it before you buy it and was assured that she had the ability. However, I find now that Zone 2 does not work with AirPlay, which was the main reason I wanted. Someone has understood how to play Airplay through Zone 2?

  Hello

• AirPlay works do not with Sony STR-DN1030

  For some reason any airplay does not appear on my device more.  It allows to work properly any suggestions?  I have confirmed that I am connected on the network even with a good wireless connection.

  Thank you

  Follow the steps below to solve the problem.

• Dolby Digital TV Apple 4th generation

  I installed the new Apple TV with Dolby Digital connected with HDMI to a Sony STR-DH540. Some applications will play in SD like the Wall Street Journal. But when I do a Crackle movie there is no center channel. However; all speakers with Roku3 work watching the same exact movie. Apple did something different from Roku. I hate to say it, but I'll use my Roku instead of the 4th generation Apple TV.

  I just tried air play a sizzle of Apple TV movie and DD this way so why not work on the Apple TV. I tried also to ABC, and it will not either SD. So far, only one for me is the WSJ.

• BD/DVD only gets speaker TV sound when connected to 1030 STR - DN

  I connected my Panasonic BD. DVD player to Sony STR - DN1030 AV receiver and can't get audio through the TV speajers. No Dolby sound. This applies to DVD and BD media. The work of BD/DVD palyer very well with other systems in my house. Y at - there a special setting that I must apply in the menu of the receiver are getting a system audio sound?

  Receiver AV plays well with the TV Sony and Netflix, it is only with the BD/DVD player that there is a problem.

  maybe go into playback sound TV GUI and diaable...

  Make sure that also in the Chamber his game to HDMI (BD player) too... and also set in the Passthru Chamber...

  Who should do it

• Remote control Medai vs STR-DN1040 cannot change the source?

  I just installed my Sony STR-DN1040 home theater receiver and have a few questions about the media remote ap...

  (1) I have it all connected and registered and the ap is functional, but in "remote mode", it lists all entries in my (BD, cable/satellite, DVD, FM, etc) as buttons, I can support on and they light up and make a tone of confirmation on my iPhone 4s, but they do not change the source to the receiver.  The rest of the features seem to work and if I use the media remote ap for go to the GUI menu, I can arrow over 'look' and then select a source, and that works fine.  The problem is when you are in another room and want to power on the receiver, then choose an audio source and play without having to turn on the TV or be in this room, you can't (or at least I can't) because the hot-key source on the ap do nothing.  What did I miss?

  (2) I have programeed the 1040's physical remote to control my Samsung Blu - Ray player.  The Medai remote access point can now also control it, or is the 1040's remote physical a completely separate device?

  Thank you!

  Hello Apcrews,

  The STRDN1040 was intended to be used with the Sony 'TV Sideview demand' which includes many new features and replace the existing approx. remote media TV Sideview will will allow you to switch between inputs, however there is no visual feedback in the app, so you'll need visibility on the front panel of the receiver or GUI.

  The application will not work to control your player of Samsung BD. The reason is that you have programmed the 1040's physical remote to control the player of comic book via codes IR (infrared), these codes resident in actual distance rather than the receiver and the orders are sent directly from the 1040's remote control.

• Dolby Digital 5.1

  Hello

  I have video clips taken with a Sony HD handycam audio Dolby 5.1. Will I be possible with Adobe Element 10 to this output to an audio in Dolby Digital 5.1 blu - ray player?

  Thank you.

  Airborne,

  The output was the part of the question, I needed clarification on too. I knew that through pre 9, the result would be a (stereo) mixer 2 channels, and checked Steve pre 10 wasn't different, about the output (export/action). However, as it is since a few versions, pre can easily import DD 5.1 SS for editing. It is the DD 5.1 SS, which is limiting.

  Now, there are ways around that, but then we must leave before making the final output and work effective with DD 5.1 SS, which would be early enough in the editing process. Minnetonka Audio offers a stand-alone DD 5.1 SS encoder, to get the Audio stream in DD 5.1 AC3 of SS.

  The reason to leave the meadow at the beginning, is that it does not offer a complete change in DD 5.1 SS, as PrPro does. Instead, use a program like Adobe hearing with multitrack editing. He can get out in six separate Audio streams, each in a separate file of 1 channel. A stand-alone encoder would then be used to get all six in an AC3 DD file.

  On a sidenote: record 5.1 SS good, Audio is really hard. Many cameras that allow it, were very close, but just placed microphones pointing in different directions, while some perform a treatment of a 2-Channel Audio stream, to create a fake 5.1 SS. In the first case, these multiple microphones usually pick up a lot of Audio, we find not very usable, such as the camera operator's clothes rub together. To save the true 5.1 SS value, needs 5 well-placed microphones (the LFE channel is usually not recorded on the spot, but separate or added, in the studio), microphones will be very narrow strip and run through a mixer multichannel, so that each can be adjusted easily. The result will be 5 discreet Audio streams, one in each of the 5 separate Audio files. Sounds people concerned will have to be well versed in recording 5.1 SS, and then the editor will have to be trained, as well. It is not as easy as just a lot of microphones, pointed in different directions. This is the area of qualified professionals, with adequate and specialized equipment.

  Offer DD 5.1 SS in camera is more a marketing tool, in my humble OPINION, and most of the users of these cameras really fight the 5.1 SS, give up on this, after just a little.

  In addition, the SS edition 5.1 is an art, even with software, such as PrPro w / Minnetonka SurCode DD 5.1 SS Audio plugin encoder option. There are so many considerations, beyond any stereo Audio.

  If you are really determined to change 5.1 SS and output to DD 5.1 SS for DVD or BD, I have several books that will prove useful.

  I do most of the projects in DD 5.1 SS with PrPro and the encoder plugin SurCode. Most are really fake 5.1 SS, I create in the studio, although some begin with 5 discrete Audio files, saved by a strong professional team and furnished to me in the form of separate WAV files. These projects are published in 5.1 SS and then I got out of the AC3 DD 5.1 SS (one of the two formats, which can be used as main Audio Source in DVD/BD) *. Often, the client will want to DTS (cannot be primary, and must be complementary Audio only). This (DD as Logic Pro, etc.) must also be out with a separate encoder (I use the SurCode DTS Encoder, which is a stand-alone and not of plug-ins, as their DD 5.1 SS), and I also work on Audio in Audition (in my workflow), out into six discrete Audio files before encoding. It is a multi-step workflow, involved, but has produced excellent results.

  Good luck

  Hunt

  * In DVD NTSC, only PCM/WAV and AC3 DD can be used for the primary Audio stream, where with PAL, MPEG Audio is optional, but really fall from grace. Not to mention that these Audio elementary streams, many others can be used on the DVD, but MUST be additional and is accessible only via a Menu or Audio button on the remote control.

• STR-DN850 remote control

  Need remote for strdn850. Model # RM - 189 AAU. Anyone?

  Hey there, loveitloud!

  Here is a link where you can buy the Sony RM-AAU189 for your Sony STR-DN850!

  https://Sony.encompass.com/item/10155847/Sony/1-492-706-11/Remote_Control_Rm-aau189

  Understanding is an authorized Sony parts distributor!

  Best regards

• AirPlay has stopped working after several months of STR DN850

  My Sony STR DN850 has worked perfectly with AirPlay for 8 months. When you use iTunes on my iMac or my Mackbook pro, I just need to play a song, and my receiver turns on and play the song. Now the small speaker selection box at the top of the window of my iTunes isn't even - probably because iTunes is not picking up an Airplay compatible device. I use Mac OS on Mac 10.9.5.

  Here is what I tried:

  1. check if I need a firmware update for my DN850 STR (I have not).

  2. repair permissions on Mac played.

  3. disconnect and restart the cable modem, router, Macs and DN850 STR. I have them all at the same time, reboot in order the cable modem, router, DN850 STR, and Macs.

  I don't see how something that worked perfectly for 8 months can suddenly stop working. I can't help thinking that there is a simple solution here, and I'm going to go for not realizing it. However, for now, I'm stuck and any help would be greatly appreciated.

  It's official: I'm a fool. I went through all the steps above again and this time it worked! I suspect that restarting the network was the culprit.