source = [h323Id = "cisco"] IncomingCalls

Similar Questions

• RV120W / RV220W source please Cisco.

  If you use Busybox binary in the firmware of your device, and if you (or the company you use) offers this feature for other (sale, give for free, etc.), you must provide users with the means to build the same binary source Busybox.

  Cisco (or F1 Team) - where can I find the source while I am able to build firmware for the Cisco RV220W?

  Archive LPG can be obtained by contacting the Small Business Support Center, which will increase the demand to level 2 support.

  In fact, here's a better way:

  http://www.Cisco.com/assets/Sol/SB/gpl_request_tool.html

• TMS directory system endpoints source folder

  Hello

  I came across a rather baffling problem with a few cases of TMS and I can't for the life in me know as to why this is happening.

  I get the following.

  in the option for creating source directory Cisco TMS, I create a new directory and link with the MSDS files and select the folder where all the end points, this creates the entries in the phone book for me as I expect with one exception, I will detail below.

  H.323 = [email protected] / * /

  H.323 = [email protected] / * /< this="" is="" where="" the="" issue="">

  IP = IP address

  I find that on some systems (this doesn't happen to all systems) in the second entry of H.323, the H.323 entry where I expect to see the directory (also known as E.164 number) number I see a URI where a field has been added at the end of the number, I'll give you a few examples below.

  DN = 1234

  set field = @video.net

  random field = @newdomain.com

  IP = 10.10.10.1

  I expect to see the following.

  H323 = [email protected] / * /

  H323 = 1234

  IP 10.10.10.1

  but I don't actually see

  H323 = [email protected] / * /

  H323 [email protected] / * /

  IP 10.10.10.1

  I have purged the TMS systems and added, I searched through the xconfig for the NouveauDomaine which is invalid and I can't find anything anywhere other than on the list of areas configured SIP VCS parameters in the second area, endpoints have disabled by default SIP and in both cases I expect to see that under a SIP entry not an H.323 entry

  This is the origin of the problem of when a user tries to call via the Directory site remote also responds to busy VCS is unable to find the appropriate directory number because the location request contains the domain as well as the DN.

  I worked around this by adding a transform to the VCS who sees the patter of specific numbering and the bands of the area, so the calls work, but I still need to understand as to what is causing this behavior.

  If I had to create the directory entries by importing information from the record of the VCS seem to be correct, its only when I try to import the entries of the endpoint via the system folder in TMS (or more exactly to import the information stored in the file on the endpoint system) I see the problem.

  a very popular Adviser.

  See you soon

  Dave

  Hello

  Picked up that the case with David and it seemed that at least on the systems the international denomination on the mxp MXP has been configured. The area of intellectual property also has a configured domain uri that has caused the other symptoms. We where able to erase the questions but still yet to see if the client is actually affected by the same configuration "mistakes".

  / Magnus

  Sent by Cisco Support technique iPhone App

• ISE with several AD

  Dear friends,

  I heard that we can integrate only 13:00 with ISE. But what happens if I need to integrate several AD EHT?

  I also learned that we can integrate multiple LDAP instances to EHT. So I can use this option for my situation?

  Thanks in advance

  -Rajiv

  That's right! Cisco ISE supports integration with a single Active Directory identity source. Cisco ISE uses this Active Directory identity source to join an Active Directory domain. If this Active Directory source has a multidomain forest, relationships of trust must exist between his domain and other areas so that Cisco ISE to retrieve information in all areas of the forest.

  However, you can create several instances for LDAP. Cisco ISE can communicate via LDAP to Active Directory servers in a domain not approved. The only limitation you would see with LDAP is a database that it does not support PEAP MSCHAPv2 (native microsoft supplicant). However, it doesn't support EAP - TLS.

  For more information you can go through the link below

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns414/ns742/ns744/docs/howto_45_multiple_active_directories.PDF

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• ISE Migration tool: Unable to connect to the ACS

  Hello

  I try starting the Cisco migration tool to migrate data to ACS 5.2 to ISE 1.1.

  When I run the migration.bat file, I get:

  C:\migTool>migration.bat
  log4j: WARN no such property [encoding] in com.cisco.acs.positron.migration.utils.Log4jTextAreaAppender.
  INFO [main] MigrationApplicationDriver.main:56: applies from the main method.
  Org.springframework.context.support.ClassPathXmlApplicat updating of INFORMATION [hand][email protected] / * /: start date [Thu Jul 11 16:46:09 CEST 2013]; root of context hierarchy
  INFO [hand] loading XML bean definitions of resource path of class [conf/META-INF/beans.xml]
  INFO [hand] instancing of the singletons in org.springframework.beans.factory.s[email protected] / * /: defining beans [exportAuthorizationProfileCache, exportConditionRightOperandCache, exportDevicesCache, exportEnumAttributeIdCache, exportEnumerationCache, exportGenericAttributesCache, exportIdentityAttr
  ibuteCache, exportIdentityDictionaryCache, exportIdentitySourceCache, exportPredefinedDataCache, exportRADIUSDictionaryCache, exportServicesCache, exportManagerImpl, m
  igrationApplicationManager, migrationPhaseStatefulComponent, stateManager, migrationProcedureModel, migrationApplicationGUI, defaultImportObjectHandlerFactory, import
  AllowedProtocolCaching, importAuthZProfileCaching, importDateTimeCaching, importDevicesCaching, importEndPointCaching, importExternalIdentityStoresCache, importIdenti
  tySourcesCaching, importPolicyElementsCache, importRadiusProxyCaching, importUsersCaching, importManagerImp, org.springframework.context.annotation.internalConfigura
  tionAnnotationProcessor, org.springframework.context.annotation.internalAutowiredAnnotationProcessor, org.springframework.context.annotation.internalRequiredAnnot
  ationProcessor, org.springframework.context.annotation.internalCommonAnnotationProcessor]; root of the hierarchy of the factory
  [Main] INFO start parsing of the XML query...
  [Main] INFO start the process XML analysis...
  INFO [Thread-5] Start ACS5 IP connection
  WARN [Thread-5] could not find the required classes (javax.activation.DataHandler and javax.mail.internet.MimeMultipart). Attachment support is disabled.
  ERROR [Thread-5] error occurred during communication with ACS 5.x. (404) not found
  ERROR [Thread-5] error occurred during communication with ACS 5.x. (404) not found
  ERROR [Thread-5] failed to connect to the DCC 5 to start exporting. Make sure that:

  1 migration interface is enabled on the ACS 5 server.
  2 ACS 5 services run.
  3 ACS 5 IP and username and password are correct.
  4 ACS 5 has a compatible license installed.
  INFO [Thread-6] Start ACS5 IP connection
  ERROR [Thread-6] error occurred during communication with ACS 5.x. (404) not found
  ERROR [Thread-6] error occurred during communication with ACS 5.x. (404) not found
  ERROR [Thread-6] failed to connect to the DCC 5 to start exporting. Make sure that:

  1 migration interface is enabled on the ACS 5 server.
  2 ACS 5 services run.
  3 ACS 5 IP and username and password are correct.
  4 ACS 5 has a compatible license installed.

  Then, I click on the export of ACS, and when I put my name to the ACS server and the password, I get:

  "

  ERROR [Thread-9] failed to connect to the DCC 5 to start exporting. Please ensure that: INFO [Thread-9] Start ACS5 IP connection
  ERROR [Thread-9] error occurred during communication with ACS 5.x. (404) not found
  ERROR [Thread-9] error occurred during communication with ACS 5.x. (404) not found
  ERROR [Thread-9] failed to connect to the DCC 5 to start exporting. Make sure that:

  1 migration interface is enabled on the server ACS5

  2 ACS 5 services run

  3 ACS 5 IP and username and password are correct

  4 ACS 5 has a compatible license installed.

  Can someone help me?

  Best regards

  David

  You have activated the web interface of migration? Check that you have configured the computer source of Cisco Secure ACS 5.1/5.2 with a unique IP address. The migration tool may fail during the migration if each interface has multiple IP address aliases.

  Document taken in charge:

  http://www.Cisco.com/en/us/docs/security/ISE/1.0.4/migration_guide/ise10_mig_install.html

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• IP over different WAN, source routing ip range? [cisco 891]

  Hi all!

  Here I am again asking for help! :)

  Here's the goal: I want a set of computers to use a WAN and another using the other WAN based on the IP address range.

  I use a router cisco 891. Fastethernet0 is a WAN, GigabitEthernet8 is the other WAN and gigabitethernet 0 to 7 are 8 switch of the router ports.

  From now on, I have my two internet access works very well, each of them is connected to a WAN port on my router. I have no problem have all my computers using a WAN or the other, or even load balancing between them, but what I want is to fix some computers with internet access and the other computer to use other internet access.

  I don't know how to do this, I looked in the delivery by source IP address, but I don't really know how to do. I saw something on the basis of routing policy, but I can only apply these policies on incoming packets that I seem not to be able to apply these policies to one of the switch port of the router. I would need to use the WAN port to connect my incoming LAN in, but then I would not be enough WAN port for both of my internet connections.

  Internet gateway #1 is 172.26.2.254

  #2 connection gateway is 192.168.1.254

  Here is my current config:
  I understand why I have bad connection whith this config since it is load balancing between the road two default and send only one of my two wan according to the INVESTIGATION period, but I don't know what to do to say precilesy Beach, the beach of IP #2 and IP #1 to go go here.

   Cisco891(config)#do sh run Building configuration... Current configuration : 3833 bytes ! ! Last configuration change at 15:11:43 UTC Tue Oct 20 2015 by *********** ! NVRAM config last updated at 14:58:11 UTC Tue Oct 20 2015 by *************** ! NVRAM config last updated at 14:58:11 UTC Tue Oct 20 2015 by ************** version 15.3 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Cisco891 ! boot-start-marker boot-end-marker ! aqm-register-fnf ! enable secret 5 ************************/ enable password ************************ ! no aaa new-model ! ! ! ! ! ! ! ip dhcp excluded-address 172.26.1.1 172.26.1.49 ip dhcp excluded-address 172.26.1.100 172.26.1.254 ip dhcp excluded-address 10.10.20.1 10.10.20.49 ip dhcp excluded-address 10.10.20.100 10.10.20.254 ! ip dhcp pool vlan1pool network 172.26.1.0 255.255.255.0 default-router 172.26.1.254 dns-server 208.67.222.222 208.67.220.220 ! ! ! ip domain name lnc360.fr ip name-server 208.67.222.222 ip name-server 208.67.220.220 ip cef no ipv6 cef ! ! ! ! ! multilink bundle-name authenticated ! ! ! ! ! ! ! license udi pid C891F-K9 sn ******************************* ! ! username ******************** privilege 15 secret ************************************* ! ! ! ! ! no ip ftp passive ip ssh time-out 60 ip ssh logging events ip ssh version 2 ! ! ! ! ! ! ! ! ! ! interface BRI0 no ip address encapsulation hdlc shutdown isdn termination multidrop ! interface FastEthernet0 ip address 192.168.1.1 255.255.255.0 ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0 switchport mode trunk no ip address ! interface GigabitEthernet1 switchport mode trunk no ip address ! interface GigabitEthernet2 switchport mode trunk no ip address ! interface GigabitEthernet3 switchport mode trunk no ip address ! interface GigabitEthernet4 switchport mode trunk no ip address ! interface GigabitEthernet5 switchport mode trunk no ip address ! interface GigabitEthernet6 switchport mode trunk no ip address ! interface GigabitEthernet7 switchport mode trunk no ip address ! interface GigabitEthernet8 ip address 172.26.2.10 255.255.255.0 ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface Vlan1 ip address 172.26.1.254 255.255.255.0 ip nat inside ip virtual-reassembly in ! interface Vlan2 ip address 10.10.10.254 255.255.255.0 ip nat inside ip virtual-reassembly in ! interface Async3 no ip address encapsulation slip ! ip forward-protocol nd ip http server ip http authentication local no ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! ip nat inside source list LAN_PCs interface GigabitEthernet8 overload ip nat inside source list LAN_servers interface FastEthernet0 overload ip route 0.0.0.0 0.0.0.0 172.26.2.254 ip route 0.0.0.0 0.0.0.0 192.168.1.254 ! ip access-list extended LAN_PCs deny ip 172.26.1.0 0.0.0.31 any deny ip 172.26.1.112 0.0.0.15 any deny ip 172.26.1.240 0.0.0.15 any permit ip 172.26.1.0 0.0.0.255 any ip access-list extended LAN_servers permit ip 10.10.10.0 0.0.0.255 any permit ip 172.26.1.0 0.0.0.31 any permit ip 172.26.1.112 0.0.0.15 any permit ip 172.26.1.240 0.0.0.15 any ! ! ! control-plane ! ! ! mgcp behavior rsip-range tgcp-only mgcp behavior comedia-role none mgcp behavior comedia-check-media-src disable mgcp behavior comedia-sdp-force disable ! mgcp profile default ! ! ! ! ! line con 0 no modem enable line aux 0 line 3 modem InOut speed 115200 flowcontrol hardware line vty 0 4 privilege level 15 password 7 ****************************************** login local transport input ssh transport output ssh line vty 5 15 password 7 *********************************************** login local transport input telnet transport output telnet ! scheduler allocate 20000 1000 ntp update-calendar ntp server 0.europe.pool.ntp.org ! end

  Thank you!

  Hello

  Apply the ACB on the SVI strategy ' sof the VLAN

  int vlan 1
  intellectual property policy map route ACB

  int vlan 2
  intellectual property policy map route ACB

  RES

  Paul

• Source for the latest HUU for server rack Cisco

  Hello, all!

  I was looking around for the latest HUU pack for my aging servers rack of Cisco.  These are the servers C210 M2 garden.  The matrix made MMIC refers to a version 14.4 (s) - which I can't find anywhere to download.  Is there a source for these packs of firmware and driver older?

  If this is not viable, a package in the range 15.X will work on one of these servers C210?  Maybe same 2.X?

  Thanks for all the research!

  Gregg

  Greg,

  Here is the link to the firmware:

  http://software.Cisco.com/download/release.html?mdfid=283862069&flowid=2...

  Here is the link for the drivers:

  http://software.Cisco.com/download/release.html?mdfid=283862069&flowid=2...

  HTH,

  -Kenny

• Cisco RV120W PPTP astronomers source IP address

  I have a VoIP application that I am trying to run over the PPTP VPN tunnel on a router RV120W.

  The system is a NEC SV8100 PBX communicate with the phone software NEC (sp310).  The system uses SIP to set up the call and for any other information signs.  It uses RTP to transmit/receive audio stream.

  The problem I have is that there is no stream audio to the phone.  SIP communication and streaming audio to the phone works fine.  The symptom is: telephony, the remote side cannot hear you, but you can hear them.

  I did a trace of the RV120W package and found the following:

  No.	Time	Source	Dest.	Protocol	Info
  948	9.358957	192.168.1.252	192.168.1.52	RTP	PT = ITU G.711 PCMU, SSRC = 0x7F1621CA, Seq = 14361, time is 779040
  949	9.359530	192.168.1.1	192.168.1.252	RTP	PT = ITU G.711 PCMU, SSRC = 0xE943F2E7, Seq = 19090, time is 3940936556
  				RTP

  192.168.1.252-ONLINE NEC PBX

  192.168.1.52 => soft phone connected via PPTP

  192.168.1.1-ONLINE RV120W

  As you can see, the IP Source address differs from that of its origin 192.168.1.52 to 192.168.1.1.  PBX NEC expects the package to come from the softphone, (192.168.1.52) not the RV120W (192.168.1.1).  As a result, it ignores the RTP for telephony package and do not relay it to the remote side.

  Is there a reason why the RV120W running NAT on PPTP packets?  Can it be turned off somehow?

  All ideas will be useful.

  Thank you!

  --

  Joe Ripley

  Choose RV220 is the option.

• Cisco ASA VPN session reflect a public IP of different source

  Hi all

  I tested and managed to successfully establish the vpn on my cisco asa 5520.

  On my syslog, I can see "parent anyconnect session has begun" during my setting up vpn and "webvpn session is over" at the end of my vpn session

  where public ip used to establish the vpn address is reflected. However after the line "webvpn session is over", I can see other lines in my syslog example "group = vpngroup, username = test, ip = x.x.x.x, disconnected session, session type: anyconnect parent, duration 0 h: 00m23s, xmt bytes: 0, rcv:0 bytes, reason: requested user" where x.x.x.x is not the ip address used to establish my vpn for remote access, it is not related to my vpn ip address below. I am very sure that the x.x.x.x ip failed any vpn for my cisco asa5520. So why it is reflected in my logs to asa cisco? Pls advise, TIA!

  Hello

  Think I remember some display on a similar question in the past. Did some research on google and the next BugID was mentioned in the discussion.

  113019 syslog reports an invalid address when the VPN client disconnects.
  CSCub72545
   

  Description

• Source:-elxcna (adapter Emulax CNA) event ID:-129 error:-\Device\RaidPort1, restore the device, has been published.

  Hi all

  Source:-elxcna (adapter Emulax CNA)
  Event ID:-129
  Error:-\Device\RaidPort1, restore the device, has been published.
  Server:-Server Rack, Windows 2008 R2
  Installed application:-installed Backup tool and IBM tape library connected by Cisco nexus switch

  Summary:-each time the backup tool initiating any SCSI command etc. for library of tapes, just after a few minutes in the event log, server shows "restore the device, \Device\RaidPort1, has been issued." and the tape library configured in backup tool disconnected from the physical tape library.

  Up to now steps below was taken but no luck:
  1. test Unit Ready has been disabled in the registry
  2 adapter ANC, fresh of zoning has been replaced.
  3 firmware and driver from the adapter of the ANC has been updated.
  4. timeout was defined according to the guidelines of this document:- http://blogs.msdn.com/b/ntdebugging/archive/2011/05/06/understanding-storage-timeouts-and-event-129-errors.aspx

  Comment:-26 fev 12:00 Am, I put to tape library firmware update and then we got
  This 129 February 26 event id error 03:00.

  Need help? :)

  Hi SabarnaDeb,

  Thanks for posting your query in the Microsoft Community Forums.

  As the question is limited to Rack in Windows 2008 server, it is better suited for the IT Pro TechNet public. Please ask your question in the Forum on TechNet Support.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  I hope it helps. If you have any questions about Windows in the future, please let us know. We will be happy to help you.

• SRW2048 and a Cisco 1841

  I am trying to Setup VLAN between a 2 and a Cisco 1841 router SRW2048 switches. I have ports that connect the 2 switches to the other and the port that connect to router as junction ports. I set 2 VLANS. VLAN 1 is just the vlan by default everyone runs and vlan will be the area demilitarized. I have no configuration of access control lists to block traffic, but when I assign vlan 2 on the port that the server is, I can not ping to the gateway. I don't know what is happening, see below for the cleaned configs.

  1841:

  Current configuration: 4282 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime localtime show-time zone
  encryption password service
  !
  hostname QCSLOLURTR01
  !
  boot-start-marker
  start the system flash c1841-advsecurityk9 - mz.124 - 25B .bin
  boot-end-marker
  !
  logging buffered debugging 8192
  !
  AAA new-model
  !
  !
  AAA authentication login default group Ganymede + local
  the AAA authentication enable default group Ganymede + none
  !
  AAA - the id of the joint session
  clock timezone CST - 6
  clock to summer time recurring CDT
  IP cef
  !
  !
  property intellectual auth-proxy max-nodata-& 3
  property intellectual admission max-nodata-& 3
  !
  !
  no ip domain search
  IP domain name qcsupply.com
  !
  !
  !
  user name x

  Archives
  The config log
  hidekeys
  !
  !
  x IP ftp username
  x IP ftp password

  !
  !
  crypto ISAKMP policy 1
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key QCSLOLU address x.x.x.x No.-xauth
  !
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac ts1
  Crypto ipsec transform-set esp - esp-md5-hmac ts2
  !
  VPN-map 10 ipsec-isakmp crypto map
  defined peer x.x.x.x
  Set transform-set ts1
  match address 101
  !
  !
  !
  interface FastEthernet0/0
  Description QCSL OLU INTERNET CONNECTION
  IP x.x.x.x where x.x.x.x
  IP access-group denied-hack-attack in
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly
  automatic duplex
  automatic speed
  No cdp enable
  card crypto vpn-map
  !
  interface FastEthernet0/1
  no ip address
  automatic duplex
  automatic speed
  !
  interface FastEthernet0/1.1
  encapsulation dot1Q 1 native
  IP 10.60.90.1 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface FastEthernet0/1.2
  encapsulation dot1Q 2
  IP 10.60.89.1 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface Serial0/0/0
  no ip address
  Shutdown
  !
  Router eigrp 100
  Network 10.60.89.0 0.0.0.255
  Network 10.60.90.0 0.0.0.255
  No Auto-resume
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 x.x.x.x
  !
  no ip address of the http server
  23 class IP http access
  local IP http authentication
  no ip http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  IP nat inside source map of route-nat interface FastEthernet0/0 overload
  IP nat inside source static tcp 10.60.89.10 80 80 extensible x.x.x.x
  IP nat inside source static tcp 10.60.89.10 expandable 443 443 x.x.x.x
  IP nat inside source static tcp 10.60.89.10 2021 x.x.x.x extensible 2021
  IP nat inside source static tcp 10.60.89.10 6100 6100 extensible x.x.x.x
  IP nat inside source static tcp 10.60.90.13 80 80 extensible x.x.x.x
  IP nat inside source static tcp 10.60.90.13 expandable 443 443 x.x.x.x
  IP nat inside source static tcp 10.60.90.13 1494 x.x.x.x extensible 1494
  !
  deny-hack-attack extended IP access list
  allow udp 0.255.255.255 x.x.x.x any eq snmp
  deny udp any any eq snmp
  deny udp any any eq tftp
  deny udp any any eq bootpc
  deny udp any any eq bootps
  deny ip x.x.x.x 0.15.255.255 all
  deny ip x.x.x.x 0.0.255.255 everything
  allow an ip
  !
  record 10.10.5.30
  access-list 23 allow 10.10.10.0 0.0.0.7
  access-list 99 allow 10.0.0.0 0.255.255.255
  access-list 99 allow x.x.x.x 0.0.1.255
  access-list 101 permit ip 10.60.90.0 0.0.0.255 10.10.0.0 0.0.255.255
  access-list 101 permit ip 10.60.89.0 0.0.0.255 10.10.0.0 0.0.255.255
  access-list 105 deny ip any host x.x.x.x
  105 ip access list allow a whole
  access-list 111 deny ip 10.60.90.0 0.0.0.255 10.10.0.0 0.0.255.255
  access-list 111 deny ip 10.60.89.0 0.0.0.255 10.10.0.0 0.0.255.255
  access-list 111 allow ip 10.60.89.0 0.0.0.255 any
  access-list 111 allow ip 10.60.90.0 0.0.0.255 any
  SNMP-server community no RO
  map of route-nat allowed 10
  corresponds to the IP 111
  !
  !
  RADIUS-server host x.x.x.x
  RADIUS-server key x
  !
  control plan
  !
  Banner motd ^ C

  x

  ^ C
  !
  Line con 0
  line to 0
  Modem InOut
  Discovery to automatically configure modem
  autohangup
  Speed 2400
  line vty 0 4
  location * Access Virtual Terminal allowed only from internal network *.
  access-class 99 in
  privilege level 15
  transport telnet entry
  line vty 5 15
  access-class 23 in
  privilege level 15
  transport telnet entry
  !
  Scheduler allocate 20000 1000
  end

  SRW2048 #1:

  Port 1: Trunk (to the router)

  Port 2: Trunk (SRW2048 #2)

  Prot 24: VLAN 2

  SRW2048 #2:

  Port 1: Trunk (of SRW2048 #1)

  Any ideas?

  Because the SRW is now part of Cisco Small Business, it would probably be best to ask the Cisco Small Business support community. You find people from Cisco over there.

  For SRW configuration, you added the two VLANS to your trunk ports? Configuration of a port in trunk mode adds automatically that all configured VLAN to the trunk.

  The server has a static IP address in the DMZ LAN?

• Cisco e1000 only route when NAT disabled

  I have a cisco e1000 itinerary. I already implemented a wireless network with success with cisco connect software. However, when I logged in the Web config, I disabled the NAT with routing table remains unchanged. the problem is that anyone of the network which links Internet WAN port can ping and receive the response of PCs within the wireless network, but it is impossible to reverse and all traffic inside e1000 can be passed through. Can someone explain this to me?

  with NAT disabled, the E1000 actually forward packets from 192.168.0.*/24 to 192.168.1.*/24 and vice versa. However, this range is effective between these 2 networks only. If a PC inside 192.168.0.*/24 send a packet to the internet, the package will pass by E1000 without changing source IP(addressed 192.168.0.*) with the address of the E1000 Wan port. Arriving at the modem, the packet can be ignored, because the modem would NAT to only local source address (192.168.1. *) or even if the package were put to rout, he would have no chance to be routed by the backbone routers.

  In addition, to be routed to 192.168.1.*/24 to 192.168.0.*/24, inside the 192.168.1.*/24 PC is configured by default with gateway 192.168.1.1 but the modem to a static route:

  dest: 192.168.0.0 mask: 255.255.255.0 Gateway: 192.168.1.W interface: Lan (W is the port of E1000 WAN address)

  and you can connect with 192.168.0.*/24 successfully.

  to summarize, I think that disable NAT would win few benefits for your internet access. As my job now requires two network so I want the E1000 to operate as a regular IP for ease router. Once again thanks for your help

• Cisco Linksys RV082 VPN router Port Translation

  Hi all

  We have a router RV082 and we try to do port forwarding.

  For example:

  88.123.2.5:80 > 192.168.1.10:2334

  88.123.2.5:81 > 192.168.1.10:2335

  However this does not seem to be possible because I can choose only the source port and IP address of destination unlike the RVS4000.

  Thank you

  These products are processed by the Cisco Small Business support community. Please refer to the URL: https://supportforums.cisco.com/community/netpro/small-business

• N4064F ip source guard without dhcp

  Hello!

  I'm having a problem with our new Dell switches.

  We are a small ISP and need to find a way to prevent users from assigning IP addresses to their equipment which do not belong to them. We hoped there was a feature similar to Cisco using static ip assignments ip source guard, but it seems that it requires the use of a DHCP server. None of our clients are in DHCP, all IP addresses are statically assigned. Is there another method or solution? Perhaps using an ACL?

  Thank you!

  I came across this post that goes beyond using source guard with static IP addresses on Cisco.

  http://bit.LY/1DsAM47

  The switches of the N series to offer the same commands with a slightly different syntax. This suggests to me that it should work the same.

  Console (config) # ip dhcp snooping
  Console (config) # interface item in gi1/0/1
  IP console(Config-if-Gi1/0/1) # check the source
  output console(Config-if-Gi1/0/1) #.
  IP console (config) # check the binding 00:11:22:33:44:55 vlan 1 1.2.3.4 interface gigabitethernet 0/1/1

  Page 521 for another look at these commands:
  http://Dell.to/1KxGn74

  An ACL would work too. You can apply an ACL entry to the physical interface that would allow only the traffic of the said IP address and then deny all other traffic.

• the source for copy tftp address configuration

  Hello

  on cisco, I can define the interface source for tftp transfers.  I can do this on 8024f? or 8132F

  Here are the valid destination URL

  TFTP: / / {IPAddress | hostname} / path/file name
  {SCP://{User@ipaddresss | hostname} / path/file name
  {sftp://{User@IPAddress | hostname} / path/file name
  Flash://filename
  USB://filename/filename

  There is no option for a specific interface.