sprtcmd.exe error after the installation of windows updates.

Similar Questions

• I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

  I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

  The primary partition has the following folders (including hidden & system)

  The recovery partition has the following (including the language files more)

  Someone at - it ideas why my laptop does not work?

  Thank you

  Greg

  Hello

  You press F11 on startup with a HP Compaq to start the recovery process.

  For problems with the recovery process, you will need to contact HP.

  BIOS problems:

  There are messages for the HP Forums for posters with similar errors:

  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

  All the answers it point to a drive about to fail

  See you soon.

• Windows 8 OEM samsung original is disabled after the installation of windows updates.

  I have the original windows 8(Samsung Laptop) confirmed by Samsung as the original windows. Have this laptop for about 2 years now and have reset my windows again. But this time after the installation of windows updates, my windows are disabled and the watermark comes and it is said to activate windows. Samsung said support windows is authentic and check with Microsoft. But Microsoft has no support for 24 hours and support is not live at this time. Can someone help me with this problem. Please, I beg you. And I tried to put the key in the firmware to activate, but nothing helped. And the OEM key is invalid for activation at all.and add I activated my windows by phone before the update using the technique of slui 4... and after it started to update. And now reactivate cant using this key method.and calling OEM is not valid anywhere.

  Hello

   
   
  Please contact Microsoft Community.
   
  We regret sincerely all the inconvenience caused to you.
   
  I suggest you try the phone activation this time and see if it helps.
   
  a. at the start screen, drag from the right side, or hover your mouse on the top right of the screen to display the menu of charms.
  b. tap or click the charm of parameters.
  c. press or click on change PC settings.
  d. If your PC is not activated, computer settings provide instructions that are customized to your activation error. If telephone support can provide assistance for your mistake, tap or click the appropriate link, which may resemble one of the following conditions:
  > Activate

  > Activate by phone

  I suggest you refer to the following article for more information.

  http://Windows.Microsoft.com/en-us/Windows-8/activation-errors
   

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  Kind regards
  Anusha

• Error fatal c0000022 after the installation of Windows updates.

  Original title: error fatal c0000022

  Hello

  I was running an update on my windows computer and it crashed. My computer came into repair mode, but when performing a restore of the system, he said:
  error 0xa - a patch prevents system from starting normally

  It then close and when it is restarted app updates he says:
  The fatal error C0000022 operation apply update 107860 105136.
  Any help or advice would be much appreciated.

  Hi Emily,.

  Thanks for posting your question in the Microsoft Community Forums.

  According to reports, after the Windows Update, receiving the fatal error C0000022, the computer crashed and entered into repair mode.

  It would be useful that you can answer questions to help you best.

  1 update you tried to install?

  2 have you tried to run safe modesystem restore?

  If you are unable to boot in normal mode, then refer to section and try the steps to solve the problem.

  Advanced Troubleshooting for General startup problems in Windows XP

  Important: Change the BIOS (Basic input output system) / Semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Note: The above link also contains measures to run the disk check. Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Hope the helps of information.

  Let us know if you need help with Windows related issues. We will be happy to help you.

• The yellow icon appearing again after the installation of Windows updates.

  Original title: Windows Update

  I went to the Start Menu and click on Windows Update.  (Microsoft Update is the real screen name.)  I clicked on Express - Get high-priority updates (recommended).  Microsoft Update now says the following: check the latest updates for your computer...  After a while the rescued and install updates appear; then I click on install updates.  Installation of updates window appears with this message: the updates are being installed.  Installstion status is reproduced below.  Extraction of the files sometimes on the screen.  Often I do it the short way; in other words, I click on the yellow at the bottom of the screen, and updated icon Instaliing up-to-date displays.  Long or short path, the yellow icon is displayed again after some time.  Why?  Also, why the rest yellow icon even after having this?

  Sincerely,

  KathyNortonKS

  Hi KathyNortonKS,

  Have updates you tried to install?

  Method 1:

  You can view the history of update to see if recently offered updates are installed or not.

  a. click Start, all programsand then click Windows Update or Microsoft Update.

  b. on the Windows Update Web site or on the Microsoft Update Web site, click view update history. A window opens that displays the updates that have been installed or that have failed to install on the computer.

  c. If you see updates failed, double-click updates failed to check the error codes.

  Method 2:

  You can read the following article and run the Fixit:

  The problem with Microsoft Windows Update is not working

  Method 3:

  You can also read the following article and perform a full scan on your computer by using the Microsoft Safety Scanner.

  Microsoft safety scanner

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• Unable to start the computer after the installation of Windows updates

  original title: same problem with the other oddities.

  I also have a computer down the update.  Although I tried several times to start the computer from the installation CD re, when I get to the page where I have options to fix or exit, locks from my computer to the top and will go no further.  Suggestions how to get the computer to boot the CD and allow me to choose the repair option without locking up?  Thank you!

  I finally managed to get the reinstallation CD to load.  I also spoke with telephone tech support at Microsoft who helped me to descend KB977165 my system.  After that was removed the computer booted without error.  By MS tech, I am also running the anti-virals and malicious programs to see if they detect all the other infections.

  Originally, the CD would load to the point of being able to choose between the options: continue to fix or exit.  At this point, the computer froze upwards and would not all repairs in order to remove KB977165.  Microsoft launches a call again tomorrow in order to install safety free bug so far.

  Thanks for your reply.

• Firewall Windows disable the Internet Explorer loads Up after slow start after the installation of Windows updates

  Hello, (this the mystery of on and Off and back on Windows Firewall with slow loading of programs like Internet Explorer as this all is pass it on firewall, disable the firewall, the firewall, it occurs only during starts, after he fine / but very annoying on reboots whom he accuses of my computer down) / listed below is the cause of it , and when she first started, you have a solution?

  I recently installed the last 16 (High Profile) updates to security, for most security updates and updates from net framework as well as the removal of malware for windows XP tool.

  After installing these updates, now my Windows Firewall turns off during 'Boot Up' on all restarts. If I try to load Internet Explorer, it will also not load up to minutes serveral / while this happens... That's fine, then finally my firewall itself loads Up quickly turns to Internet Explorer and back on during this time around the same time.

  After these updates these things are happening on my computer now, it's as if there is a process running, but nothing run any virus, Trojan or worm etc just these updates caused this problem. I don't know if it updates is corrupt or not, but have tried different things as system file checker /scan etc with no luck.

  (1) computer boots to the top and seems to Load Up Fine ' until the ' or 'Look at this' but isn't, something is running in the background or process "wing unstalled" is obviously "unhooked", etc..

  2) try to load Internet Explorer last minutes and is very slow to load up, even if I 'don't load Internet Explorer' must still a long while that as in the firewall turn off for awhile some several «minutes» (way too long), before "auto turn on automatically return.

  (3) turns firewall Windows itself on "finally" as Internet Explorer finally loads upwards as well the two Internet Explorer is able to load 'definitely' and the firewall is on "finally" as many minutes later as listed above, at the same time.

  This could be the cause? Only, it has begun to 'After' I ran windows update and installed the 'most recently high security updates for windows XP' there were 16 listed mainly security updates and updates of net framework as well as the software removal tool windows malware.

  That's all that is changed on my system, I tried many things, nothing seems to fix this problem with my computer. I know for a fact that these updates are the cause, but am not sure that you caused it? Or how do to solve this problem, any sugguestions would be appreciated.

  Please answer questions following diagnosis by number in your very next answer (no need to quote this post):

  1. what application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  2 a Norton or McAfee application already installed on the computer?

  3. do you have a Norton or McAfee free trial come preinstalled on the computer when you bought it? (No matter if you have never used or activated).

  4. you are using IE6, IE7 or IE8?

  5. have you ALREADY had the opportunity to do a Repair Installation of Windows XP for some reason any?

  PS: PLEASE DO NOT START ANYTHING IN ADDITION TO NEW THREADS ABOUT IT!

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Get 364 error during the installation of Windows Update.

  Original title: I get an error code 364 on my windows vista computer. It will not download new update please help! I want to solve this problem without having to pay anything. Thank you

  whenever I shut my computer down it trys to download updates from the window. but then, when I turn on back says error364. Help, please!

  Hi Vicky,

  We need after the details on your part to help you better.

  (1) what is the exact full error message?

  (2) do you have any third-party security software or antivirus installed on your computer?

  Check the updates installed properly on your computer. Double-click the update that shows unsuccessful, and write us with error codes. You can follow the steps in the link below.

  See the Windows updates are installed

  http://Windows.Microsoft.com/en-in/Windows-Vista/see-which-Windows-updates-are-installed

  You can also provide us with the details of the event viewer. Follow the steps below.

  Open event viewer

  http://Windows.Microsoft.com/en-in/Windows-Vista/open-Event-Viewer

  You could deal with this question for various reasons. Windows update fails to install if there is a conflict with a third-party security software installed on your computer. Follow the troubleshooting steps below.

  Step 1: Temporarily disable all security software. 

   

  Temporarily disable anti-virus software or any other security software temporarily on your computer.

  Warning: security software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Step 2: How to reset the Windows Update components?

   

  http://support.Microsoft.com/kb/971058

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.

  http://Windows.Microsoft.com/en-in/Windows-Vista/back-up-the-registry

  You can see the steps in the link below.

  Problems with installing updates

   

  http://Windows.Microsoft.com/en-in/Windows-Vista/troubleshoot-problems-with-installing-updates

  Write to us at the State of the question. We will be happy to help you come.

• restart after the installation of windows updates

  After a reboot after you download 3 updates my computer is stuck at configering 3 0f 3 updates 70% and will not move. I tried (after waiting several hours) to restart the computer but it only gos to 3 of 3 70%.

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  Then:

  Click Start > right click on computer > properties > Windows updates down the lower left corner > updates installed in the lower left corner in the next window

  > then click the one that you don't want > uninstall will appear at the top > uninstall it.

  In addition, on the page where you clicked "Installed updates", click on change settings at the top left corner it

  > Change update settings in the next page of AutoUpdate to "check for updates but let me choose etc" > OK ".

  When you take a look at pending updates, you can either download/install them one at the time, namely the bad.

  > or if you do not need an individual > right-click on > UAC prompt > hide it

  See you soon.

  Mick Murphy - Microsoft partner

• Unable to start after the installation of Windows updates

  original title: windows update 10/11/2011.

  When I install the updates above that my pc does not restart, I restore it to before the update and my itunes icon disappears.

  I installed both times and the same thing happened twice, am now a little worried if you want to try again or what to do next.

  Any help would be greatly appreciated, but nothing technical massively please!

  Thank you

  Nigel.

  Hello Nigel,

  I would recommend installing either of these updates at the same time until you see this behavior.

  When this occurred, use system restore to go back to when the last update was installed and can hide the update, which is the origin of the problem.

  Best regards

  Matthew_Ha

• Vista Stop error message: 0XC012001D after the installation of Windows updates.

  Original title: vista stop working

  Hello

  I need help on vista, because I update and restart and stop working and appear this error code:

  !! 0xc012001d! Registry\Machine\Components\DriverData...

  Hello

   

  
  1. remember the number of the update you have installed?
  2. could you give us the exact error message?
  3. Once you get this error message? Are you able to boot to the desktop?

   

  Method 1.
  Please check if you face the same problem when recording in safe mode. It is a possibility that one of the non-Microsoft application or driver is causing this issue. Start in safe mode and make sure that us. If you are able to start properly in safe mode, we can perform a clean boot in order to find the root cause.
   
  Step A.
  a. restart your computer.
  b. when the computer starts, you will see your computer hardware are listed. When you see this information tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows Vista Advanced Boot Options.
  c. using the arrow keys, select the desired option of Mode without failure.
  d. press the Enter key on your keyboard to start in safe mode of Windows Vista.
  e. when Windows starts, you will be at a typical logon screen. Connect to your computer and the Windows Vista goes into safe mode.
  f. do whatever tasks you need and when you are done, reboot to return to normal mode.
   
  Step B.
  If it works fine in safe mode try performing a clean boot in order to find the cause root.
  See the article below for instructions on how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete do not forget to reset the computer to a normal startup. Follow step 7 in the above article.
   

   

  Method 2.
  Best thing you can do is to perform a system restore just before where the problem occurred.
  I have listed a few articles that explain the system restore in Windows 7.
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  
  System restore
  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  Thus, the article above is applicable to Windows Vista.

   

   

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• What can I do to correct a startup problem that has begun to occur immediately after the installation of windows updates today? I was about to save some work but ran the updates before hand

  I have just to complete installation of updates on my compaq presario sr2037x... and when it restarted it goes to the ' start windows normally, safe mode, safe mode w/network, w/command prompt safemode and the last known good configuration "screen... I tried to start windows normally, then the last known good configuration and not matter what I do it looks like its about to start up, then a brief blue screen flashes then I finish immediately at the start screen mode to choose.

  BSoD on my xp. Thank you microsoft. No problem until your update. You are the people going to do about it? Does not load in any case, in any case.

  STOP: 0X000000E3 (0X80558BE0, 0X81B4B020, 0X00000000, 0X00000002)

  Found this by searching. don't know if it will work again. This update might be the problem. KB971486

  Link here.  http://www.stateofthetech.com/?p=117

  Read on to find some easier ways to fix. Now, I must go and get a record of Microsofts problem!

• Windows Media Player 11 has changed color after the installation of Windows updates.

  Original title: Windows Media Player 11 has changed color.

  Since the last update from Microsoft, the media player iteself blushed and the color picker that is not responding. She still plays the videos, but they also have a red color that doesn't change when I adjust the video settings. Does anyone know how I can fix it.

  I use Windows XP Professional with SP3 and my graphics card is a NVIDIA GeForce2 MX/MX 400.

  Hi DanielDavey,

  Thanks for the reply.

  Glad to know that the problem has been resolved. If you have any further questions on your computer, thanks for posting your question, we will be happy to help you.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Explorer.EXE error after the restoration of the ERD Commander

  Dell Inspiron B130

  Windows XP Service Pack 2

  Recently performed a HD format and new installation of XP SP2. After I installed all the drivers and others, I checked that the system was operating normally. After a few days of use, Windows Update downloaded Service Pack 3 and asked me to install. I started to install SP3, but at about 50%, the laptop battery is dead at Midway through the installation. I plugged the laptop on the power source and power. I restarted the laptop and XP started only a completely black screen and the white slider. No ALT + CTRL + DEL, desktop icons, etc.

  I rebooted the laptop of ERD Commander, ran the restore system and selected the first available Restore Point. Point of restoration chosen was recorded a few days before, and was the first recorded point after the clean installed XP. I rebooted the XP system. Wallpaper loaded with white cursor, but NO start menu or desktop icon. A message appears saying "Explorer.EXE Application error, press OK to exit the application" or something very similar. Did not write the error code, but can get if necessary. If I press the OK button (which is my only option), there is still no icons on the desktop or the start menu. Only the cursor. No access ALT + CTRL + DELETE or something like that.

  Thinking about completely wipe the system and reinstalls the operating system. Any suggestions before I jump in this solution?

  Explorer.EXE error after the Restore Point of ERD Commander. Dell Inspiron B130. Recently clean installed XP SP2 on laptop. Installation of SP3, to 50%, battery dies the laptop right in the middle of the installation of the SP3 update. Restarted, XP starts with black screen with cursor only. ERD restart order and restore XP to the last known good config (I choose point immediately after XP clean install). Reboot to XP. Now the wallpaper shows as well as the error message saying "Explorer.exe Application error, click OK to exit Explorer" dialog and then I can't access anything. Any ideas?

  Hello

  What is the full and exact error message?

  Step 1: Check if you are able to boot into safe mode without any problem. If you are able to boot into safe mode without any problems then try to perform the clean boot to safe mode. Also disconnect any external devices connected to the computer.

  Reference:
  To start the computer in safe mode
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  Step 2: If you are still having the same problem, then you can the steps at the bottom of the article.
  How do I recover from a corrupted registry that prevents Windows XP startup
  http://support.Microsoft.com/kb/307545

• LSD unexpected closing of the errors after the installation of el capitan

  LSD unexpected closing of the errors after the installation of el capitan

  get a lot of errors after start-up and during work

  This procedure will remove some cache files. The files are generated automatically and do not contain any of your data. Sometimes they can become corrupted and cause problems like yours.

  Please, back up all data.

  Triple-click anywhere in the line of text below on this page to select this option:

  open $TMPDIR..

  Copy the selected text in the Clipboard by pressing Control-C key combination.

  Launch the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Paste in the Terminal window by pressing command + V. Depending on the web browser you use, you may need to press the return key. A folder with a long, random name should open. Inside, there should be a subfolder named 'C '. Drag that to the trash.

  Log off or restart the computer. Empty the trash. Test.