SSLVPN need on my router

Similar Questions

• do I need a wireless router to print Jet Office 6700

  I'm working on site with no internet connection, I need a wireless router to print Jet Office 6700? I don't have a USB cable.

  Hello

  You get two options: using direct wireless (which isn't reliable) to buy a USB cable for about 10 euros. If you want to use direct wireless, use the following configuration:

  http://support.HP.com/us-en/document/c03353355

  Kind regards.

• Bad IP address. Cannot renew. Wireless network. No need for a router.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideais:

  • You have problems with programs
  • Error messages
  1. Recent changes to your computer
  • What you have already tried to solve the problem

  Please provide details of your problem.

  What do you mean by "bad"IP address "?

  What happens when you try to renew the IP address?

  What do you mean by "wireless network. No router needed?  Do you mean you are using a 3G modem or that you connect to a wireless access point that is not yours?

  What version of Windows, including the service pack is installed?

  Please provide the following diagnostic information:

  1. start > run > cmd > OK
  2. type this command in the black command prompt window and press ENTER:
  ipconfig/all > "% UserProfile%\Desktop\ip.txt" {Enter}
  3. open the IP.txt file to your desktop
  4. copy and paste the text into your response.

• SSLVPN - impossible to verify routing

  Greetings,

  I enter the following shortly after the cut in our SSLVPN on an ASA5510. I was unable to find anything about this error, or find something wrong with our configurations. Any help will be appreciated.

  Group user IP SVC Message: 17/ERROR: cannot successfully verify all routing table changes are correct...

  ... There is no routing table changes made. It left me speechless.

  Thank you

  Check software SSL is updated, otherwise it will give errors when you try to connect.

• Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

  Hello

  Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

  The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

  Please, what missing am me?

  A few exits:

  ISAKMP crypto to show her:

  isakmp crypto #show her

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  Crypto ipsec to show her:

  Interface: GigabitEthernet0/0

  Tag crypto map: QRIOSMAP, local addr 62.173.32.122

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

  current_peer 62.173.32.50 port 500

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  #pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0

  #pkts not unpacked: 0, #pkts decompress failed: 0

  Errors #send 0, #recv 0 errors

  local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

  Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

  current outbound SPI: 0x4D7E4817 (1300121623)

  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:

  SPI: 0xEACF9A (15388570)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

  calendar of his: service life remaining (k/s) key: (4491222/1015)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  Please see my config:

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  encryption... isakmp key address 62.X.X... 50

  ISAKMP crypto keepalive 10 periodicals

  !

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

  !

  QRIOSMAP 10 ipsec-isakmp crypto map

  peer 62.X.X set... 50

  transformation-TS-QRIOS game

  PFS group2 Set

  match address 100

  !

  !

  !

  !

  !

  interface GigabitEthernet0/0

  Description WAN CONNECTION

  62.X.X IP... 124 255.255.255.248 secondary

  62.X.X IP... 123 255.255.255.248 secondary

  62.X.X IP... 122 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  card crypto QRIOSMAP

  !

  interface GigabitEthernet0/0.2

  !

  interface GigabitEthernet0/1

  LAN CONNECTION description $ES_LAN$

  address 192.168.20.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  !

  IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

  IP nat inside source list 1 pool mypool overload

  overload of IP nat inside source list 100 interface GigabitEthernet0/0

  !

  access-list 1 permit 192.168.20.0 0.0.0.255

  access-list 2 allow 10.2.0.0 0.0.0.255

  Note access-list 100 category QRIOSVPNTRAFFIC = 4

  Note access-list 100 IPSec rule

  access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

  access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

  access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

  access-list 101 deny ip any any newspaper

  access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 110 permit ip 192.168.20.0 0.0.0.255 any

  !

  !

  !

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

  Here are the things I see in your config

  I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

  IP route 0.0.0.0 0.0.0.0 62.X.X... 121

  IP route 0.0.0.0 0.0.0.0 62.172.32.121

  This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

  IP route 10.2.0.0 255.255.255.0 192.168.20.2

  In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

  IP route 172.17.0.0 255.255.0.0 Tunnel20

  IP route 172.17.2.0 255.255.255.0 Tunnel20

  And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

  IP route 172.18.0.0 255.255.0.0 Tunnel20

  IP route 172.18.0.0 Tunnel20 255.255.255.252

  HTH

  Rick

• Why would I need to DMZ router to scan?

  If you feel you have tried everything to get the scanner to communicate with the computer and nothing will do, a service representative can tell you to DMZ the printer.  Often I have heard the term used loosely, and it can be very confusing if taken the wrong way.  That's why I deliberately formulated my question as I did.  First of all, you don't want the router DMZ.  You want to DMZ IP address of the printer in the router to open ports which also insist on remaining blocked.

  I considered all the reasons, we'd lose communication with their scanner.  The reasons are plentiful and can leave a user struggling for hours trying to get their scanner to communicate with their computer.  After that a standard troubleshooting is complete, they turn to their router.  Of course, this message only relates to people who have their printers attached to their computer with an Ethernet cable or wireless.  Before I define exactly what means DMZ, first of all I want to look at why you want to do.

  Printers to communicate through several different ports.  Often routers are configured with an internal firewall to protect users of computers from outside attacks.  In this way, the only information that the computer receives comes from what the router allows through.  People might DMZ their computer for games purposes, but it would be a very bad idea.  People are misled by "reliable companies," which suggests this in order to access their personal files.  Essentially, the goal was really to contain the amount of traffic actually pass through the router at the same time so this is a feature of security and service.

  A printer has been designed to communicate through a series of ports, but sometimes these ports are blocked.  Maybe the router is due for an update, or a firmware update was conducted which could cause the printer to lose communication.  Often, people can still print which is what it makes it even more confusing.  Ports of printing are simple and well known in the world of routers.  However, scanners to operate on a level more complex.  Information is received by a port and another goes out.

  Some companies may even install a proxy server in order to reduce bandwidth and record or monitor traffic which is an example of a blocked port.  In addition, as an extra level of protection, routers differ in the configuration so that it is difficult to gain access to a network for malicious purposes.  Depending on the router and other sources of firewall, like on the computer (antivirus software and Windows Firewall), these ports may deny access to a device of 'unknown' otherwise on what seems to be a random basis.  Of course, it is not random, but the timing is always impeccable none-the-less.

  DMZ printer (also known as the port forwarding in some cases) would mean completely open all the ports of this device.  It stands for demilitarized Zone.  Open ports in this subnet to the router allows access without any additional security.  That's why doing it on the IP address of the computer is a bad idea because that which allows people outside access to your computer network.  With ports closed here, they are allowed access by the user as a download in an email that contains a virus.

  On a printer, there is no way to access the files, install viruses or damage to the printer.  Especially if it's just a home network, the risk of attack is null.  It's not as if they could tap into your network as long as it is password protected initially.  The pirates have honestly no reason to print on your printer, in order to open the ports for access to the printer is perfectly acceptable and safe.  Now, if you were totally to the DMZ the router, then Yes, but a advanced user would know the term, just so the application, expresses or misunderstood is still virtually impossible to do the entire router.  Instead, just follow these steps so that you know that there is nothing blocking the scanner to work.

  Because routers differ from a product, a non-technical person would better communicate with their provider internet router service or undertaking for them through the steps on how to do.  Directly into the router just looks like a bad idea if you have never done it before.  Sometimes the router companies will help you for free if you are in warranty, if not the biggest complaint I hear is that they want you to pay xx.xx amount to do what your internet service provider must be able to do it for free.  If you find that you are unable to find someone to do it for free, you can always search the router manual and find information in the title of port forwarding.  However, that information is not openly scattered on the world wide web because of the risk factor to plug the wrong numbers and completely block the communication with the printer.

  After I uninstalled the printer, temporarily disabled the startup and anti-virus programs, reinstalled the printer software and find I'm still able to analyze, the next thing I look at is the router.  A technical agent on the phone, I didn't have the right to access the 3rd party software and hardware, that I have been trained, so I sent an email, which included all the ports, the printer uses and at the request of a reminder.  You can just go down the list of ports and follow the instructions on how to open each one individually, or you could just DMZ IP address which opens all ports on the printer.  Seems easier to DMZ it or what is even easier to do just told someone else to do not understand the definition themselves.

  As I said, it can be confusing and frustrating, especially if it is beyond your level of troubleshooting, but everyone who has managed to do, so always the spokesperson saying they could analyze now.  9 times out of 10 it worked.  And at that time, he remained effectively resolved.  With regard to the other 10%, they had other issues inside the computer as well.

  So, if you are already in this situation, contact your router or your ISP company for how to do this.  Here is the list of ports that I would include in my email, which would also suggest updating the firmware on the router first, and then going on with port forwarding.  This is all from my understanding and experience, I learned this. It's rather simple information that I hope will help you understand why someone would tell you to do.

  Incoming (UDP) ports are ports of destination on the computer while outgoing ports (TCP) are ports of destination on the HP printer.

  • Incoming (UDP) ports: 137, 138, 161, 427

  • Outgoing (TCP) ports: 137, 139, 427, 9100, 9220, 9500

  The ports are used for the following functions:

  Print

  • UDP ports: 427, 137, 161
  • TCP port: 9100

  Download of photo card

  • UDP ports: 137, 138, 427
  • TCP port: 139

  Scanning

  • UDP port: 427
  • TCP ports: 9220, 9500

  The HP device status

  • UDP port: 161

  Faxing

  • UDP port: 427
  • TCP port: 9220

  Installation of device HP

  • UDP port: 427

  Ports of Web Services

  • UDP and TCP: 80, 443, 5222 and 5223

  Hello Ports

  • TCP and UDP: 5353 and 5297, 5298

• Advice needed on Optimal routing device specific and small businesses

  Hello
  I have worked mainly in the system of security for several years now, but has been approached by my father to help with a project of home office he seeks to complete.  Currently, he runs a Web server of its headquarters which is connected to one of the ports on an old Linksys router.  It works also all the home devices (Smart TV, laptops, phones, etc.) through a port other than same router.  The goal of the project is to separate these two networks (home or office) of bandwidth and security purposes.  He attempted to contact his ISP for a second connection installed, but I guess that their policy allows a connection must be installed in a single House.
  My original idea was to implement secondary interfaces on external port that goes to the ISP but the current Linksys router is so old and only accessible via HTTP/HTTPS is not able to support the secondary interfaces or VLANS.  I expect some tips on the different options on the routers for individuals and small businesses that support interfaces and which would achieve the objective of this project.  I would prefer something that uses Cisco IOS and that can be managed from a command line, but am open to all options.  Any help would be greatly appreciated!

  Hello

  Connect a layer 3 Switch Cisco to the router. You can create a VLAN on the switch, create all the lass on the switch, and then route the switch router.

  http://www.Cisco.com/c/en/us/products/switches/small-business-300-series...

  I'm not employed by CISCO, but hope this helps.

  Have a good Christmas.

• E1700 advanced routing - need help

  I'm unable to create static routes through my Linksys E1700 (v1, f/w 1.0.02 Rev. I get errors on all roads, I try to enter. I receive a complaint that is not part of an IP address in the range 1-233 or I get the "Road of Invalid" error message when trying to save the road.

  Can someone show what restrictions are applied on the input static routes?

  Access to a DSL modem to which the router is attached is what I want to achieve. This means I have assigned the modem to an IP address that is not on the local network and the need for the router to pass this address via the WAN port, but not at the gateway of the ISP.

  Something along the lines of:

  Local address of the router and the IP address range used by DHCP from the router: 192.168.0.0/24

  Local address of the ADSL modem: 192.168.1.1/24

  I want the route: 192.168.1.1/32 via WLAN interface with gateway 0.0.0.0

  Any ideas why the router does not allow me to do this?

  Also, if I could get any type of road through the WLAN E1700 interface I could affect my modem must match (as long as it is not an IP address, I need to use :-)) but I was not able to set up a road to the WLAN interface with gateway 0.0.0.0.

  / Nils

  Unfortunately, the service VLAN on the routers of the series E is only for specialized ISP configurations and should not be confused with abilities VLAN typical.

  In most routers grade consumer the LAN\Switch Ports is a layer2 managed switch. Some such as OpenWRT and DD - WRT firmwares have the ability to independently assign tags VLAN to the LAN Ports. The switch may have that a single IP address assigned.

  I do not understand this correctly, that's all this so you can access the Modem since the E1700 LAN? So then try to configure the Modem in Bridge mode and configure the E1700 with the PPPoe ISP connection. Then the LAN E1700 you should be able to ping the Modem at the address 192.168.0.1, assuming that the E1700 router IP address is 192.168.1.1 subnet 255.255.255.0.

• Time capsule with modem/router

  I just got the phone with Apple support and they told me that time capsule will not work itself but he need a modem/router REQUIRED to work all time capsule. Is this true? Time Capsule is a modem/router. Why on earth someone would buy something for $ 600, which is not even replace the old modem router? I spend $ 200 on a 3 TB hard drive and do the same work. Please answer.

  Time Capsule is a modem/router.

  No, this is not correct.

  The Capsule is a router only. It doesn't have a modem on board. If you have a Time Capsule and you want to be able to access the Internet, you will need a modem to connect to the time Capsule.

  More providers of Internet services (ISP) provide modems/routers and modems to their customers to connect to their service. Please contact your ISP and ask them what they recommend.

• Best router for streaming technology

  Hello, I work with streaming technology, and I would like to know some references (names, links) on the best routers (wired) to the video streaming. (Send and receive)

  Thank you!

  Leandro - BR

  OK in that case you need just a router high power of small businesses such as the LRT224.

• LG Wireless adapter upward adjustment to work with the WRT54G Router

  My parents recently bought a TV high definition LG and they got a wireless adapter to LG for it (YEAR-WF100). My brother was able to insall, but when trying to connect to the router, we get an error message saying DHCP must be enabled. From what I see when I go in the settings of the router, DHCP is enabled. We are pulling our hair out trying to figure out what we need on the router so that it works settings. We tried the two setting up the connection manually and automatically with the IP, gateway, etc. I don't know what other information is needed, but I'll give you more details if anyone has any ideas. We have also two apps created by Applications and games tab (Nintendo DS and Wii). I do not know if that might interfere with anything. Any help would be appreciated!

  After spending two hours on the phone with the Geek Squad (Fortunately it was free), we found the problem is that the router was set to WEP settings, and it must be WPA. Too bad the Nintendo DS only supports WEP. I guess I can just switch back to WEP when I go online on the DS. Thank you for taking the time to help!

• WRT160 - routing issues

  Hello

  I want to install a WRT160 to an existing network.  I'm on Qwest with their DSL modem. My network router's network 10.0.0.0/16 Vyatta.  I know that the 160 is a router (must have purchased access point instead, my fault), so I placed its IP address as 10.1.0.1.  PC connect very well and have a good IP address of the DHCP server, but they cannot access the other subnet or on the internet.

  I guess I need a static route added to my router Vyatta, right?  If so, what would be this way?

  Thank you.

  Problem solved... model me!  I had active rip.  Once I disabled it, everything works!  Sorry for the trouble.

• Do I have to buy an adapter wireless network in over a wireless router, or there at - it an adapter already installed on the computer?

  OK - I'm not savvy computer whatsoever, I would get that out of the way.  I just got internet at home, and unfortunately it is wired, so I must be connected to the wall if I want to use.  I want to go wireless as soon as possible and find out that I need a wireless router.  My question is, do I need to buy a wireless adapter as well?  Or is something already installed internally on my computer?  I have a Dell Inspiron 1545, Vista, (if it's even relevant information)...  I checked my adapters and it wasn't that anything listed that specifically, 'Wireless', said however, there is "Intel(r) WiFi 1500 AGN" - this could be what I'm looking for?  Otherwise and I just need to buy a separate adapter bitch, please let me know... Thank you very much!

  The 'Intel(r) WiFi 1500 AGN"is a wireless network adapter.  You don't need to buy anything.
  Boulder computer Maven
  Most Microsoft Valuable Professional

• My HP Officejet 6500 E710a-f can communicate with the router or wireless access point

  I don't even know if my printer supports wireless or not there only ethernet logo on it and no wireless setting in its control panel as shown in the manual, I plugged on the router via a cable many years ago but now, for some reason, I need get the router of the printer if it can communicate with the Wireless router and if she can , how it will be, and to ensure in this... I have no parameters to talk wireless in the printer, but as I remember in his specification he supported wireless do not know if I got the wrong specifications or my printer is missing something.

  and it is my printer status

  Hello

  Unfortunately, it is not a wireless printer:

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/my-OfficeJet-6500-E710a-f-wont-print-wirelessly-Windows-7/TD-p/1820813

  Kind regards.

• Live Z10 Z10 WIFI blackBerry to the top of my home wireless router

  I have another strange problem with this phone.  A few weeks ago, our always reliable wireless router stop working.  We restarted it and it worked for a while then quite new.  I don't think about it at the time but just before I was trying to get my phone attached to the wifi at home and that's when I noticed the wifi, it wasn't ' work.  I finally gave up.  The next day we rebooted the router and had no problems.  A few days later, I decided to plug in my phone to wifi and all of a sudden, we noticed that he needed for the router to reboot again.  Since then, the only time wherever we had problems when I used my phone in wifi to work but I forgot to turn off barriers go home.  Once I get in the House, the router freaks out and we lose wifi.   Anyone encountered this?  You have any suggestions?

  I finally got the phone company to go out and talk about their wireless router.  My phone is no longer live it upward.  I hope just as I don't accidentally mess up someone elses wireless router when I have my WI - FI value phone and receive in the proximity of their wireless router.  When he saw upward, all on the router looks OK, but it clears any access until you turn off the WIFI on the phone then reboot the router.