Store.E wireless adapter Firmware

Similar Questions

• Cannot connect Stor.E Wireless Adapter + 1 TB HDD in my laptop

  I recently bought a Stor.e wireless adapter for use with my partner Stor.e 1 TB HDD laptop but I can't seem to connect to my laptop.

  If I plug the HARD drive directly into my laptop everything appears also ok but if I connect via the wireless adapter that shows nothing. the instructions that come with the adapter are very poor, but after following the instructions stating "plug drive HARD adapter using the USB cable then plug taken adapter (AC power), the LED flashes of HARD drive and the lights on the wireless adapter showing 1, 2 green, solid = power, wireless = 3 green, strong." USB = blue.

  The disc shows hard on my Android phone and the android Tablet but won't connect, when you perform a scan for wireless on my laptop devices, the adapter cannot be found.

  I sent twice, the support from Toshiba on July 5 and July 10, but have not received the courtesy of a response although confirmation of receipt of my e-mail, so for them we will get back to you in the DAY a statement.

  ANY help with this problem would be highly appreciated.
  Thanks in advance.

  Hello

  Stor.E WLan adapter extends a USB HDD with the ability to access data stored via a WLan connection.
  This means that you must activate your WLan on your laptop and configure the Stor.E WLan adapter first.

  The 3 LEDS have the following meaning:
  Above 1 LED is on / off and lights up green if the adapter is running
  The LED 2 is WiFi link and turns green where wi - fi access has been established.
  The 3rd (first from the bottom) lights up blue when the HARD drive is mounted. Flashing LED means read/write mode.

  How to connect?
  Connect adapter to Canvio Stor.E WLan adapt to the B USB 2.0 (near the reset button) microphone connector and connect the USB HDD to the type A USB 2.0 connector.

  You will need to activate the laptop s Wlan and press the reset button (hold it long 4 sec). The Wireless settings, you should see the Canvio Stor.E open wireless card that you connect access point.

  Then, in the Web browser using IP address: "http://198.168.65.1" to access the settings page of the Canvio Stor.E wireless adapter.

  In the preview, you can see the current version of the firmware, storage devices, network access point information.

  The list of devices shows detailed information on connected devices.
  Within the network, you can find the devault sotre.e wireless adapter network settings

  Now, you can use an Android application called Toshiba Wireless Adapter to move files on the HARD drive connected to the WiFi adapter from your smartphone.

  You can also map the card wifi as a network drive in Windows system.
  In type of Explorer: \\198.168.65.1. then right-click and choose map network drive.
  In a new window, select the application letter to the new drive (Z) and click the Finish button.

• Toshiba stor.e wireless adapter, WiFi password

  Hello, my problem is that I forget my wifi password
  Toshiba STOR. Connection of the E, solution no wireless card

  There is a small hole

  

  Use a paper clip or other object and that insert into the hole.
  Hold 5-10 sec and the settings must be reset again default

• Toshiba stor. Connection wireless adapter E smartphone problem

  Hello world.
  I have a shop. E wireless adapter I can not connect with some devices. When I use my laptop, it works perfectly. I also tried with a s4 Galaxy and a Note 2, both work.

  My Samsung Galaxy 4 marks used to connect to this subject when I was on 4.4 kitkat firmware, I could access my hard drive without any problem. But since I upgraded 5.0.1 is not connected to its network Wi - Fi. I updated the adapter android app wirelessly on game store that shows an improvement on the lollipop. Network adapter is displayed on my rating 4 but when I type the password it does not connect. When I remove the password protection, it connects to the WiFi but I can not access my files.
  I also have the problem of connection with my sister's computer, it shows the Wi - Fi, but can't type the password.
  Does anyone know how to fix this?

  Thank you so much everyone.

  Hello.

  I would like to add that my sister's laptop is on windows 8.1, that would cause it not to connect?

  Thank you

• Model wireless adapter for HP Pavilion 15

  Hello

  I need to buy a wireless adapter for my HP Pavilion Notebook of 15 and I would like to know the company, the model and configuration of the same.

  HP has an online store in the United Kingdom where I can purchase this item?

  Details of the laptop:

  Model: HP Pavilion 15

  Processor: AMD 5750 APU A10

  RAM: 8 GB

  Graphics card: AMD Radeon HD 8650 + 8600 M

  HARD DRIVE: 1 TB

  Motherboard: 1983 01.15

  System BIOS: F.33

  OS: Windows 8.1

  Thank you

  Hi @Metal_Head,.

  Shows that you are connected to a network that is not identified with limited capabilities.

  To troubleshoot the wireless, you will need to remove the Ethernet cable.

  If you right click on the Network Center and sharing, disconnect the connection you and connect to your router.

  Thank you.

• Problem with access point or wireless adapter

  Hello world

  tried to connect to my WiFi, but the convenience store detects that the problem with access point or wireless adapter.
  The drivers are up-to-date and functioning normally. There were discussions on BIOS but I don't know if I would be able to complete the task without bricking your laptop.

  Is there any online support?

  Hi smert

  Your message is not really useful.
  Why? Because no one knows all the details of the laptop, wireless network card system...
  So please would you be kind enough to provide more details.

  But despite the missing information, I recommend:
  (1) reset your router WLan
  (2) check the connection to the WiFi unsecured. (of course for testing purposes)
  (3) check the different (WPA/WPA2 AES, TKIP) encryption

• A6210 guard disconnect wireless adapter

  Every 30-40 minutes, or so my A6210 wireless adapter is connected to the router but not the Internet. This is for 2-3 minutes until the adapter connects to the Internet. How can I solve this problem? I am constantly disconnected from online games, I'm in and it sucks. During this period of 2-3 minutes, Internet on my other devices works fine, but not on this PC. I also use WIndows 10 and have the latest firmware for Netgear engineering, 1.0.0.34.

  If you have anti virus or firewall, try to uninstall it to l ' moment and observe the connection. If still the same, I would contact our support.

• HP OfficeJet 4500 G510-m: set a wireless adapter in the port of my HP OfficeJet 4500 G510-M Ethernet

  Hello, a recent update of fiber in my house left me without an Ethernet cable to my HP OfficeJet 4500 G510-M.

  Can I connect a wireless adapter to the ethernet port on the printer?  I could use the USB connection, attach it to a computer and share the printer to the network.  I thought to fix a wireless to the printer adapter would give me the most flexibility.

  Thoughts?

  Thank you

  Dan

  Hello @tarfy58,

  Welcome to the forums of HP.

  I understand that you are looking for alternative methods to put your Officejet 4500 G510-M on your network.

  I would like to help.

  Unfortunately the printers firmware would not know what to do with the wireless adapter.

  You would need something like HP 1200w NFC/Wireless Mobile Print accessory.

  The only downside is that I saw the Officejet 4500 on the list of supported printers.

  Please check the specs of the device, in case I missed it.

  Your method the most effective would be to use the USB connection, attach it to a computer,

  and share the printer to the network.

• Wireless Adapter PCI not capable speed.

  I have a Cisco EA6500 and I'm trying to understand why I don't get the speed I should to two wireless PC.

  The pc (laptop) uses an adapter Broadcom 802.11n network and speeds range from 5 Mbps to 28mbps then than a direct wired pc

  for him becomes router upward of 50 Mbps I installed the most recent driver. Even to place the right of the laptop next to the router

  does not change the speed. Could get a USB wireless adapter help?

  I tried for this search in the forum, but has failed to find something similar. (No connection so many)

  Any idea?

  Thank you

  Dennis

  Hi, RMJ, since you have an AC router, it may be better to purchase a power adapter as well. In this way, the optimal speed and a range that offers the router can be reached. You can check WUSB6300 and AE6000,http://store.linksys.com/products/linksys-adapters_stcVVcatId552067VVviewcat.htm. Hope that helps.

• WIRELESS ADAPTER WILL NOT WORK UNLESS THE WIRED CONNECTION IS PRESENT

  PROBLEM: RECENTLY SPEND YOUR DESKTOP OF WIN - XP TO WIN 7 32 BIT AND MY HP LAP TOP VISTA 32, WINDOWS 7, 64 BIT.

  WIRELESS LAPTOP ADAPTER, NOT REARRANGE ITSELF TO USE A WIRELESS NETWORK

  CONNECTION. THE ROUTER AND WIRELESS ADAPTER HAVE THE CORRECT INFORMATION CONFIGURATION AND WORK WELL USING THE WIRED NETWORK. WHEN I MOVE THE NIC WIRELESS WI - FI FAILS.

  INFO WIRELESS ROUTER:

  LINKSYS BRAND: WRT300N V1.1
  BASIC WIRELESS SETTINGS: NETWORK RADIO BAND = AUTO, CHANNEL = MIXED MODE = AUTO, SSID = ACTIVE.
  WIRELESS SECURITY = WPA PERSONAL WITH TKIP ENCRYPTION

  WIRELESS ADAPTER, INTEL (R) WIRELESS WIFI LINK 4965AGN

  HP Pavilion DV 9700, WIN 7 64 bit update for Win Vista 32, NVidia Ge Force 8600 m GS graphic card, Win 7 64 bit.

  WHEN I CLICK ON THE ICON TO ACCESS INTERNET AND CLICK ON THE NETWORK TO CONNECT, THE WINDOWS NETWORK DIAGNOSTIC DIALOGUE BOX SHOWS CONNECTED, BUT FAILS TO COMPLETELY MAKE THE CONNECTION. WATCH THEN RESOLVE THE PROBLEMS, WHICH FAILS AND FINALLY TO INVESTIGATE THE PROBLEMS OF ROUTER OR ACCESS POINT...

  OTHER PEOPLE HAVE THIS PROBLEM, WHEN THEY SWITCH TO WIN 7. BUT THERE WAS NO MIRACLE DOCUMENTED THAT I CAN FIND ON THE WEB. IN THE OTHER FORUMS DISCUSS ISSUES RELATED TO THIS PROBLEM CONGREGATE, THEY PROVIDE NO BUGS. I NEED HELP TO SET UP MY WIRELESS NETWORK ADAPTER TO THE RECONFIGURATION OF THE WIRELESS NETWORK.

  Thank you all who responded and have tried to help me. Before posting, I tried most of the mentioned patches, including upgrading my firmware of the router. In addition, I went to Device Manager and scanned for changes and checked the properties under the Advanced tab of the Wifi link adapter. I tried the update driver and deactivation and activation of the device. None of this has worked.

  Finally, I uninstalled and then reinstalled the Wifi card. It worked. I guess the driver software became corrupt and data of the register of the device had probably need re - install, this is what worked. This seems to happen when upgrading Windows operating systems prior to WIN 7 and later people lose their wifi connection. Then this problem develops.

  It worked for me. I hope this works for others with the same problem.

  Once again I thank you all.

• -SOLVED! -PCI or USB wireless adapter is disabled and will not activate on Windows 7

  The solution: uninstall ZoneAlarm!

  I spent 3 days and 3 different cards, trying to solve this problem. First of all, I bought a Netgear PCI wireless adapter. Installed according to the instructions. Device Manager showed the adapter works properly but turned off and nothing I tried would enable the adapter.

  NETGEAR has taken over to the store and buy a Linksys PCI wireless adapter. Exactly the same problem. Device Manager, said the adapter worked correctly, but turned off and would not turn on.

  So I called Linksys support and paid them only for the remote service and they couldn't get it to work either (of course to return money). They suggest is to contact Microsoft technical support or buy the USB version.

  I went and picked up the USB (WUSB600-N v.2) version today and guess what? Exactly the same problem. Device Manager showed the device works correctly, but turned off and would not turn on. After talking to a few other technicians in addition to myself, we agreed that the only other option was to reinstall windows. But just before I decided to do, I checked one last time to Google and came across a post in the forums of Vista by someone who had the same exact problem, uninstalled ZoneAlarm and then worked their wireless adapter.

  Well, I decided to try that before reinstalling windows. As soon as I uninstalled ZoneAlarm and the computer restarts, the adapter has been activated and automatically found my network! This means that ZoneAlarm control network on the computer and for some reason cards some not allowing a wireless adapter is enabled.

  Then I tried to re-setup of ZoneAlarm. After that I have re-installed, my wireless adapter became instantly disabled and would not turn on again. So I uninstalled ZoneAlarm at all times. My router has SPI and NAT firewall on top of the Windows Firewall, so I need anyway ZA.

  If you have ZoneAlarm, get rid of it. If you still experience the problem of your card activating Wireless does not and have ZoneAlarm, try to uninstall any firewall software 3rd - party that you have already installed (not the Windows Firewall).

  I was really frustrated after spending 3 days with 3 different adapters and many trips to stores using the adapters and buy different cards. I'm glad I found this post on the forums of Vista, so the credit goes to the one who made this post.

  On a side note, after I installed the drivers from the CD and Linksys site, Windows update has shown there is an updated driver on the site of Ralink which I installed it and so far no problem. My WUSB600-N automatically connected to the strip of the 5 GHz on my router dual band and speeds are ultra fast and signal is strong in a completely different room.

  Hope this information helps others finally solve this problem.

  See you soon,.

  Matt

  64-bit, but it should work on either. ZoneAlarm includes network connections and was not what allows the adapter to be activated. Even close ZoneAlarm does not work either. ZoneAlarm must be uninstalled from the card must be activated.

  Vista drivers work fine with this adapter. Then a Windows Update is the updated drivers for Ralink which also work very well.

  If you have properly installed the drivers and display device manager the device works correctly, but disabled, and then uninstall any firewall/antivirus 3 rd-party should do the trick.

  I am a tech, more I consulted other technicians as well as paid for technical support of Linksys and nobody could understand this problem and it's no wonder. Who would have thought that ZoneAlarm or any 3rd part antivirus/firewall software would take complete control over network connections and not to allow a new network adapters must be installed correctly.

  If anyone needs any help other than that, feel free to ask.

• New wireless adapter does not connect to my router

  at home, I have a wireless router WRT120N set up for wireless internet connections, I also use the wireless adapter that comes with it. I recently bought a new adapter wireless like this: http://global.level1.com/product_d.php?id=891 and it connect to the router? Help, please

  I think that the wireless connection on your router may not work properly.

  Create a new wireless network.

  Connect the computer to the router with the Ethernet cable. Open the router setup page and go to the Wireless tab, change the name of the SSID wireless network to create a new wireless network. Change the channel to 11. Save the settings.

  Go to the tab of sup of wireless security and check the security settings. Make sure you have the key/password network correct.

  Go to the sub-tab to Wireless MAC filter and make sure that it is disabled.

  Go into the settings wireless Advanced tab change the interval of tag to 75, RTS and Fragmentation threshold to 2304. Save the settings.

  Now ty to connect to the new wireless network.

  If this does not work then try upgrading/re-Flash the firmware on your router.

  Connect the computer to the router with the Ethernet cable.

  Download the latest firmware from the site Web of Linksys and save it to your computer. Open the router configuration page and update the firmware on your router. After upgrading the firmware of your router, reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 30 seconds. Power cycle the router and reconfigure.

• Dynex N guard disconnect wireless adapter

  warning disconnect wireless adapter

  Go to the website of the manufacturer of your router > make sure you have the latest Firmware in Vista for it.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  Try without commitment TCP/IPv6:

  If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

  http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

  See you soon.

  Mick Murphy - Microsoft partner

• HP 350 1: laptop wireless adapter problem

  I have problems about to connect to a wifi network. Sometimes my laptop does not show available wireless networks, even if I'm sitting next to the wifi router.

  If I try to connect to the wifi, when an available network, the brand wireless on windows bar notification area spots turns into a red cross mark and say cant connect to available networks list netwok.the will also emply.and shortly after, once again it shows there's available networks.

  This happens again and again.

  If I run 2 or 3 times convenience store network, sometimes it connect to the network.

  So now, I have to perform network troubleshooting whenever I connect to a wifi network.

  If I turnd on wifi on shutdown of laptop, it takes a long time (about two minutes) to start windows.

  If the wifi turned off when stopped, computer laptop startup kill 30 seckonds.

  I tried driver re install, driver updates.but it does not work.

  Please give me a sollution.

  model-hp 350g 1

  wireless adapter-Ralink Wi - Fi adapter 802.11bgn RT3290

  driver version - 5.0.46.0

  Windows 8.1 company

  I think that you have tried them all... new driver, uninstall and reinstall... what else can it be? Maybe delete and physically to reinsert the card wireless, but if you do you could also stir this thing and put in a real wifi for $5 card.

• NETGEAR wireless adapter connects to a network other than mine.

  I started using a NETGEAR wireless adapter and it worked very well, always connect to my NETGEAR network. Then a few days later he began connecting to the default profile for the Native WIFI instead of NETGEAR. This part of the Windows 7 operating system, or someone is hack my wireless connection? How can I get rid of him? I reconnect to my network, but it reconnects to the Native WIFI default profile. Any help or info is greatly appreciated.

  original title: Native WIFI by default profile

  Radron,

  "Native WIFI" usually refers to a Windows SDK API and it is more likely that it is a programming error that someone hack into your system.

  I begin by visiting the site Web of Netgear, enter the model number of your wireless adapter and install the latest drivers for Windows 7:
  http://KB.NETGEAR.com/app/

  I'm fairly certain that updating the drivers will solve this problem. If not, switch to update the firmware on your router.

  I hope this helps!

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.