STR-DH520 component video

Similar Questions

• STR-DH520 margin adding video HDMI

  My HTPC sends 1920 x 1080 video via HDMI to the Sony APR: STR-DH520.

  Who then sends video to my Samsung Smart TV also capable of 1920 x 1080 via HDMI.

  However, the AVR adds a margin to the image such that there is one inch

  unused screen on the left and right and one half inch of unused screen up and down.

  When I connect the HDMI directly to the HTPC video card TV, there is no margin.

  The Windows 7 video driver knows he's talking to the Sony APR.

  I checked the resolution presented by the HTPC and the settings of the TV screen.

  How can I get the Sony APR to fill the screen?

  Hi Codetonic,

  What you are experiencing is called scanning. The only adjustment to change will turn the PASS THRU feature it so the TV does not see additional CEC via the HDMI connection protocols.

  If this not reslove the issue, are there any changes of the Samsung Smart TV to the mapping of pixels? These settings are usually in the settings screen called display area. If it's characteristic is present in the TV menu mark an attempt to reduce it by-1 or - 2 or increases by + 1 or + 2.

  If my post answered your question, please mark it as an "acceptable Solution".

• STR-DH520 no sound HDMI

  Hello

  I recently bought a STR-DH520 and I'm trying to get audio through HDMI to my P8H77 - I motherboard on my computer, but so far without success.

  If I connect the computer directly to my TV or the sound projector is read from this device. If I connect it to the amp I get no sound from the speakers any audio playback device I select on the computer. However, if I select the projector as a device for reading on the computer I hear the projector (for HDMI passthrough works)

  I have selected the right speaker configuration and have performed a calibration, so I can check that the speakers are working.

  An update, I tried with another computer, still no luck.

• Support VGA component video output?

  I want to connect my Inspiron E1705 to TV using video connections component.  What is component video output VGA?

  My DELL system

  Inspiron E1705 shipped on 09/04/06
  Windows XP Media Center Edition 2002 Service Pack 2
  Intel Core 2 Duo processor T2300:1.66 hz

  2 GB 533 MHz RAM

  
  

• Why some of my clips making go white screen in component video

  Why do some of my clips making go white screen in the video component?

  How should one know without details...?

• T42 - made component video via VGA card supported?

  I want to connect my T42 to my home theater receiver. I started to buy a (receiver) component cable VGA (from T42) but please make sure that T42 video card compatible with it. Anyone know?

  you have an as left and right analog audio input on the receiver? You must use the headphone port out of the T42.

• STR-DA5700ES no video/audio HDMI inputs no

  STR-DA5700ES has no audio/no video inputs HDMI (except PS3 hooked up through GAME that works). It was fine yesterday (for the last 2 years). Now, suddenly, there's nothing. I did a power reset (by holding the button until it has adjusted) and exchanged the HDMI cables. Any suggestions?

  Turns out have been a matter of HDCP, possibly caused by cables, which have now been replaced with new cables by their manufacturer as directed by their guarantee. The problem can only be solved by completely reset the 5700ES (memory clear). Please consult the manual of Sony if you're having a similar problem.

• Qosmio G30: Can I use component video software plug-in to connect the Gamecube or PS2?

  The Qosmio G30 has a VIDEO-IN bit for the red/white/yellow wires... So I wondered if this meant that I could connect my PS2/Gamecube/similar to television, playing games on my laptop, save me money when I move to College :)

  Indeed, if I pretend that I'll put up a set - top box for the TELEVISION, the Gamecube appears under "Video Composite", I just can't save like a channel or anything at this point...

  Someone help? Would be very grateful...
  Thankee.

  Hello
  The s-video-in port can be used to connect and to import data from the external device such as an analog video camera or VCR. Imported video can be edited or written on a DVD disc.
  Video port can be used to connect the external device such as a game console

  I think you should also consult the user manual because you will find the full description on unique ports and use.

• MCU IP Cisco component video conference

  Hello

  I install an MCU on my environment, but is not able of composition to another device of video conferencing, dial the IP address, but it does not conect the 'call '.

  MCU are able to make that kind of call?
  If Yes, how should I proceed with this call?

  Thank you and best regards.

  Pedro,

  Do you search rules necessary on the RESUME calls to ip address?

  If you MCU is VCS registry all call req will go to the VCS control and vcs decided where to make calls. Let me tell you want to call a unit on the internet using the ip address.

  MCU sends req call vcs, and then vcs needs a search rule where he should deliver this ip address. by default on the CV "called to unknown ip" is indirect and so you need to add a search rule VCS-control as "any" target "any ip address" would be the crossing area.

  by calls VCS - E unnknown ip are set to 'direct' by default if you don't need all the rules of research. If the firewall settings are clean, then call get settle.

  also when you say dial to ip address, what ip address speak you an interal or public ip address end point?

  Rgds

  Alok

• Help please - component video using the same clip several times

  Hi people,

  I have a 9 minute video I want to cut into pieces and make a 3 min video. I searched the help system and Forum, but found nothing - very probably (not being is not a native speaker) looking for the wrong keywords.

  How can I add the same clip several times to a movie? If that has been resolved, I could do the rest with setting- and outpoints and would.

  Thank you in advance.

  Christoph

  You can place the clip on the timeline and use the Split Clip (small scissors under the monitor icon) to split your clip. Place the cursor where you want to trim your clip, and then click the icon of the scissors. Move the cursor to the next position, and then click the icon of the scissors again. Then press DELETE on your keyboard and that article will be deleted and the gap will be closed. If you wish, you can take small sections, you created and drag them around to change their positions.

  Once you have edited your clip, you can export the section 3 minutes as a DV - AVI to use repeatedly in your video. All you need to do to export is file > export > Movie. If you have several clips on your timeline you must place the work area bar (WAB), the gray bar above the timeline, on the section that you want to export. Then in the window export movie go into settings and for the beach, select work area bar.

  You can then reimport the 3 minute clip in your project and use it as many times as you want.

• Trouble with 5 speaker set to str dh520

  I have the speakers whirled for correct connections, but could not get the right configuration to save the system.

  Hello Ann,.
  Welcome to the community of Sony.

  You can refer to the # 30 of the manual page to select speaker model according to the speaker system you use.
  You can also adjust the size and the distance of the speakers connected to this unit by following the steps mentioned in the chapter "MENU SPEAKER" on page # 57.

  Please mark it as "acceptable Solution" If you find this information useful.

  Kind regards
  Colby

• Warrenty info -: STR-DH520

  I don't get all the sounds of one of my speakers. I ran the test tone and receives no sound, I changed my speakers wired, has changed and what a speaker not working. How can I start to return my receiver for repair.

  channel right surround back/front

  Hi RRANGEL,

  I'm sorry for the issue with the President. It seems that this particular speaker is not working. This receiver has 2-year warranty for labor and parts from the date of purchase (US only). You can get it fixed for free under warranty.

  http://www.docs.Sony.com/release/Warranty_455717303.PDF

  Click on the link below to request a repair initiate for the receiver (US only):

  https://eService.Sony.com/webrma/Web/index.do

  If you are not from the United States, click on the link below to contact the local Sony Support:

  http://www.Sony.net/SonyInfo/support/

  If my post answered your question, please click "Accept as Solution", this will help other users to easily find their answers when navigating through community site.

• STR-DH520 - pass through

  Why my camera starts when I turn on my my TV to the receiver input. I have my ps3 connected to the receiver, then the receiver to the TV. I don't want the receiver all the time. But when I turn on the TV to the hdmi input, my receiver turns on. I have so I have to turn off the receiver and then continue 5000mAh mode.

  Rrangel,

  If you just reset your receiver and then you have to turn ON HDMI Pass Through.  It can also be beneficial for reference manual STRDH520 to understand what settings are available and how to use them to achieve your desired results.

  Settings HDMI (page 60)

  Control for HDMI [CTRL. HDMI] ON BY DEFAULT - CHANGE to OFF

  Passage of Signal HDMI in [COL. THRU] OFF BY DEFAULT-CHANGE on

• Qosmio G20 = video cable component and videos in high definition with Pinnacle

  Dear everybody
  I bought my Qosmio G20-120 of the Poland that came with D video cable SCART. This cable is only capable of transferring video signals (CVBS) which is pretty useless, because Qoismio already has a S-video out... What is the best simple video production I can get to SCART.
  According to www.toshiba-europe.com Qoismio is supposed to have video output component. But it comes with cable SCART instead. I always try to make this component video cable D-video of the Distributor. If I don't succeed, does anyone know if and where I can buy this cable in Europe? Or is it possible to make a video component with the D-video out D-video cable with cable SCART?
  Everyone last tried the channels high definition DVB-S on Qoismio using USB 2.0 DVB - S TV Card.Any opinions on Pinnacle PCTV 400e?
  Thank you

  Hello

  Sorry, but I don t agree with you. SCART in my opinion is always better than S-Video. As far as I know cable SCART can transfer image and sound and picture just S-Video. Am I wrong?

  In my view, it's great that laptop Qosmio has two video ports and each use can make a choice.

  Another way your ad is a bit confusing to me. Qosmio G20 includes a section on the port (D-video) and as far as I know the original cable must be provided. You can see on this page http://support.toshiba-tro.de/KB0/TSB4A00TK000MR01.htm

  Using this cable you can easily connect your laptop to the TV.

  Also check this http://support.toshiba-tro.de/kb0/FAQ5300XK0012R01.htm document
  It can also be interesting and useful to you.

  Good luck!

• How to view a new movieclip before a video component?

  Hi all
  
  I hope some can help me with this problem.
  
  My problem concerns the visibility of the movieclips and text that have been created by the program at the time of execution, with respect to a video device that was created in the Flash IDE (since the video components cannot be created when running?).
  
  The clips are always returned BEHIND the video component, which is annoying because they are supposed to be an overlay on the video stream.
  
  They are created on startup with statements such as:
  this.createEmptyMovieClip ("mcOverlay", this.getNextHighestDepth ());
  mclOverlayLoader.loadClip (" http://www.mydomain.com/clip.swf", mcOverlay);
  But the clip is always displayed behind _root.video (which has been set at creation time).
  
  How can I create a movieclip (or text) when the execution and force him to appear before a video object that is already on the scene (at the time of the design)?
  
  
  Any suggestions are appreciated.
  
  Barry

  Items that are placed on the stage at the time of the author are organized by layer, and this can create problems when you try to instantiate new objects and organize them in depth. Depth and layers are different things.

  The solution to your practical problem is to simply create an empty MovieClip object on the scene at the time of the author, put it in a layer above your component video and then give it the instance name, you can reference from your code. You can simply attach the other MovieClip objects to this, or load new content inside.