MCU IP Cisco component video conference

Similar Questions

• A few questions about the video conference via the public network

  Hi all

  I have a few questions that need your help:

  1. normally, I connect endpoints to MCU via local network (extended WAN) so everything is OK. But if I want to connect to the MCU via the public network (e.g. Internet FTTH), am I any equipment more or MCU settings? Need video firewall option?

  2 Cisco Telepresence does support VPN for remote endpoint to join video conference?

  Thank you

  Hi yours!

  (1) If you are looking in the connectivity, I would recommend that you speak to someone in sales of cisco (partner)

  to tell you a little more about the deployment of VCS-E and VCS - C.

  You need something to do good firewall/nat traversal, not only for the nat in your organization,

  but also for remote users with endpoints behind a nat home router,...

  (2) the endpoints and the infrastructure do not have a vpn client, but you can of course use VPN router between the two.

  But you should know that the video uses a certain packets per second and bandwidth so the vpn router could

  in trouble and a vpn also adds the overhead rate ip then you have MTU problems.

  But yes, I saw people using Cisco Telepresence via VPN.

  Yours: Please note the answers using the stars below!

• EXTERNAL VIDEO CONFERENCE DROP AFTER SECONDS

  Salvation;

  I have a MSD 15.3.0 version and TMSXE 5.3,
  I have a wooded area, with:
  10.5.2.10000 - 5 CUCM
  PRESENCE 10.5.2.21900 - 4
  TMSPE: 1.7
  CONDUCTOR: 4.2
  NŒUDS EXPRESSAY: 8.6 (EXP-E clusters and cluster EXP - C)
  TELEPRESENCE SERVER: 4.2 (4.23)

  Salvation;

  When I create a new video conference using the SCHEDULER INTELLIGENT or CMR, an external user cannot stay in a conference, this connection is dropped after every seconds.  In my vts newspapers exist the message below, where information this close due failure invitations SIP call.

  274 2016/09/12 16:47:47.768 SIP Info call 10.254.0.30:42033
  "" 16:47:47.771 275 2016/09/12 call APP Info 21: incoming new SIP call of '[email protected] / * /"
  276 2016/09/12 16:47:47.953 calling APP Info 21: "FABIO 2s" has now joined Conference "Reuniao Agendada 09/12/2016 16:24.
  277 2016/09/12 16:48:09.340 calling APP Info 21: stopped contributing video, now contribute audio only
  Time from NTP Info 278 2016/09/12 16:48:10.706 is my Sep 12 16:48:10 2016
  279 2016/09/12 16:48:16.058 SIP Info call 10.254.0.30:42033
  "" 2016/09/12 280 16:48:16.061 calling APP Info 22: incoming new SIP call of '[email protected] / * /"
  281 2016/09/12 16:48:16.098 calling APP Info 22: "Leonardo Silva" has now joined Conference "Reuniao Agendada 09/12/2016 16:24.
  Appeal of error SIP 16:48:23.743 282 2016/09/12 22: close call due to failed invitations
  283 2016/09/12 16:48:23.743 call CMGR Info 22: disconnection, '[email protected] / * /"-service not available".
  284 2016/09/12 16:48:23.745 calling APP Info 22: shoot call them from "Leonardo Silva" - destroy at request end. not available
  SIP 16:48:23.835 285 warning call 2016/09/12 22: unable to close successfully the dialogue with BYE
  286 2016/09/12 16:48:31.937 call CMGR Info 21: disconnection, '[email protected]/ * / '.
  287 2016/09/12 16:48:31.937 calling APP Info 21: shoot call them "Fabio 2s" - destroy at request end. remoteTeardown
  

  I have check all information in othe Detective Conan in this forum: https://supportforums.cisco.com/discussion/12294701/telepresence-server-...

  I made recommendations, but with IX Protocol disable SIP PROFILE DRIVER and MEETING ALIAS, the same error occurs. My maximum size of incoming messages is updated to be 11000.

  Internal Conference is going on normally.

  Any idea?

  Best regards;

  Fabio Santos

  I've seen some similar behaviour in the past - on trunk SIP pointing to the highway, try to uncheck the "SRTP allowed" and see if it works.

• Video streaming via video-conference notebooks

  Hi all

  "I'm setting up a video conference to three places and I use the ' CTS-EDGE95-K9" for each of the sites.

  Now, they want to be able to communications stream video via laptops (at least 5 instead of the eact) in each of the three locations.

  Now it is possible with devices that it is? Or do I need to add additional devices?

  Also, how is assigned license here?

  Please this Advisor will be appreciated.

  Kind regards

  Peter.

  95 EDGE Codec offers an internal streaming server.

  The streaming service can be configured through the web interface of the system or the system itself.

  I don't know how many viewers continuous sleeps well.

  Details on the streaming service can be found in the Administrator's guide or the link below.

  http://www.Cisco.com/en/us/prod/collateral/ps7060/ps11304/ps11313/ps11382/data_sheet_c78-628575.html

• Tandberg MCU 5300 series supports the Conference me the feature?

  Hi all

  I would like to know that the 5300 Tandberg MCU series supports the Conference me the feature?

  We checked the 5320 MCU data sheet,

  Cisco TelePresence MCU 5320 CTI-5320-MCU-K9

  Comes with: 5320 - MCU and cables - MCU ports must be enabled with optional port licenses

  Software for Cisco TelePresence MCU 5320 license options

  1 nHD full HD/2 HD/4 SD/8 ports on 5320 MCU (max 10 with this option (6 used for nHD)) LIC-5300-4PL

  Second option Ethernet port (VFO) for the MCU 5320 LIC-5300-VFO

  AES and HTTPS option for the MCU 5320 LIC-AESMCU53-K9

  However, there is no information related to Conference me function.

  So, can we know everything that Tandberg MCU 5300 series supports the Conference me the feature?

  Best regards

  Ben

  Hi Ben,

  Conference is not compatible with the MCU 5300 series.

  Best regards

  Markus

  Sent by Cisco Support technique iPad App

• Video conference system

  We have two requests of the customer on the videoconferencing solution can someone

  1.

  .       In the current scenario once the video conference session created & participating all joined the conference call, his name appears first & teleconference establishing later after their name disappears.

  Requirement is to show their name/display name of participant for during the entire session of the call

  2.

  Second requirement the Conference telephone automatic planning via a device MCU (centralised management); instead of everyone (all participants) dial for bridge, it should start by the central unit on behalf of everyone & connect all conference participants (depending on the time of the meeting of the Conference call will get launched from the centralized management system)

  For you to invite participants that are preconfigured, you must first add them as endpoints H.323 or SIP on the MCU. Just follow the guide supplied. Once added, you can invite participants pre-configured by checking just them and the MCU will automatically dial on these parameters once the Conference starts.

  By going in the global settings of MCU:

  Settings > Conferences > time to display the names of the participants

  This setting determines whether (and how long) participants showed for the components is accompanied by their name provided.

  Kind regards

  Acevirgil

• STR-DH520 component video

  I just moved into a house where they have a line consisting of the closet to the tv area. I have a Sony Bravia HD TV which has been great to work for a few years. I don't want to pull a HDMI cable in the tube where the sons of component are so I went and bought a Sony STF-DH520 a / audiovisual receiver. I hang a DVD and a Comcast HDMI in HDMI input on the receiver ports and plug a HDMI to the TV output. Works very well.

  I then try to use the Monitor Out on the receiver and connect a component video (red, blue, green) and I get no video on the TV. Then I try just the (composite) video cable to the video output on the back of the av receiver and no luck there.

  Did I miss something until I take this thing back to the store? Page 21 of the manual shows that I can have a HDMI or Component out to my TV output. It should work.
  http://store.Sony.com/wcsstore/SonyStyl... 248878.PDF

  Thanks for any help,
  Tom

  from page 22 in your manual
  "Entry of video signals to HDMI IN may
  only be transmitted via the HDMI TV OUTPUT
  Jack. Video input signals cannot be
  exit through the VIDEO OUT jacks or
  MONITOR OUT taken. »
  I think it is the way that most all receivers work. I would run the HDMI.

• SX80 simultanius video conference

  Hi all, I have a question made media sx80 multiple videoconferences at the same time, for example, if my client wants 2 video conference independent of each other, the sx80 does very well. also without CallControl

  Video input camera--> Room1

  Video output--> Room1

  Audio--> Room1

  Audio--> Room1

  Video input camera--> Room2

  Video output--> Room2

  Audio--> Room2

  Audio--> Room2

  The SX80, like any other video conferencing end point (and regardless of manufacturing), may not pysically connected to a room at a time.  Cannot connect a single codec in several rooms, each with their own camera and microphones and have individual conferences for each room.  Your only option if you want each piece to be able to make Conference calls independent of each other is purchase and SX80 for each room or share the unique SX80 allowing only when using it.

• TMS Video Conference MAster API commands

  I have a scenario where we use the master setting of Video conference in TMS to try to set some parameters in a room that are controlled by a third-party controller.

  So if a site is the master we configure profiles as back camera on the monitor back on the sharing of specific content etc...

  I went through the document of the API to find answers, but I can't find what I'm looking for.

  When TMS books call all of this info stored locally on the codec before the beginning of the call?  So I could query codec to find out if he was master in the next cal...

  I found that the subject of conferences has the info I need, but I don't know how to access it.  I could go in and leave the data I need I think.

  My good that process would be to get the call ID once we first booked and updated the list of session on the codec, then go to the object of the reservation for this ID call and parse the xml file.

  I know it's weird but I am is my correct thought that there is a file object of booking for each call?

  HI Brandon,.

  If I understand your question, you can run the command on a TC endpoint:

  xcommand booking list

  This will provide information about the meeting, as well as the following line:

  * r BookingsListResult booking 1 role: Master

  If it is not master it will say slave

  Hope that answers your question

  Sebastian

• SX20 block unwanted call during the session of the video conference

  Hi all

  It should be your advisor on it

  I have a set of SX20 that is configured as a standalone device (No. CUCM, VCS).

  Its work fine, able to make and receive calls through the IP address.

  Things in our video conference meeting, is sometimes a unwanted number would call us and disrupt the flow of the meeting.

  I don't know how they get our IP address, but we don't expect their call.

  Is there any way a setting to block many unwanted call us or disturb us during the video conference meeting.

  Is there any configuration that I need set the SX20 itself to prevent the unwanted phone number

  Please notify

  Titebiket

  This is probably a scan SIPVicious or similar, which is how the call is 'you find '.

  I have not tried it myself, but there is a selection option or not to allow incoming calls when already in a conference call:

   Conference 1 IncomingMultisiteCall Mode: Deny

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Cisco Unified Video Advantage connect not not Cisco IP Phone

  Hi, I have the following text:

  • CUVA 2.2.2.0 installed on windows 7 x 64.
  • UC560.
  • IP phone 7965.

  The first time I installed the program, everything was ok, didn t try the video feature, but it was connecting and recognize.

  Now I'm with another phone, also a 7965 but CUVA said that it is not connected. He also says: "cisco unified video advantage can't connect to cisco ip phone" and asked him to contact the system administrator.

  It has been a long time (about 3 weeks) because I checked the last time he was working on the previous phone, I'm not sure if it's because I'm on another phone now, but I do not.

  Any ideas?

  When you go to CUVA-> all show the driver see CDP?

  Have you tried to close your wireless adapter or set a higher metric?

  Got a GPO that would restrict CUVA on windows firewall?

• Video conference Flash - getting started

  I'm a developer, ASP.net/c# implementation of a Flash site interested video conference.

  Any help would be appreciated.

  -Allan

  Flash MX is really obsolete.

  I think that it would be desirable to learn AS3 and perhaps have a good book of reference available... can't really Advisor that one is better than the other. But Flash AS3 is a very broad subject. If your goal is highly concentrated... Flash Video Conferencing, then you might want to rely more on resources, forums and online reference documents.

  http://www.gotmyidea.com/78377-008-editing-a-FlashMeeting-video-replay.php

  http://FMSGuru.com/forum/messages.cfm?ThreadId=F15363BB-A7BB-AAF9-2A5A47F24BD6B20D

  http://www.WinSite.com/Web-development/Web-design/Flash-video-chat/

  other Forums Flash:

  http://Board.flashkit.com/Board/index.php

  http://www.ActionScript.org/forums/index.php3

  but you will need to work with streaming multimedia server so be sure to contact the Red5 Forum mentioned above as well as

  http://forums.Adobe.com/community/Flash/flash_media_server

  and

  http://forums.Adobe.com/community/Flash/flash_media_live_encoder

  Best wishes

  Adninjastrator

• Support VGA component video output?

  I want to connect my Inspiron E1705 to TV using video connections component.  What is component video output VGA?

  My DELL system

  Inspiron E1705 shipped on 09/04/06
  Windows XP Media Center Edition 2002 Service Pack 2
  Intel Core 2 Duo processor T2300:1.66 hz

  2 GB 533 MHz RAM

  
  

• test network for video conference. Cisco best practices

  Are there documents and software to test the network not only immersive systems but the halls as well? Cisco TelePresence Readiness Assessment Manager? Please provide documents relating to best practices.

  Thank you

  Sent by Cisco Support technique iPad App

  Hi Chris,

  Please find the "Cisco TelePresence Network Systems Design Guide 2.0" document series CTS here:

  https://supportforums.Cisco.com/docs/doc-23422

  For T3 immersive systems, we have another document, please take a look at this document:

  https://supportforums.Cisco.com/docs/doc-23391

  Are there specific points of termination/infrastructure you would need more information ready network?

  For more information concerning understanding Cisco TelePresence latency Jitter and loss targets and thresholds, please have a look here:

  https://supportforums.Cisco.com/docs/doc-23423

  The single telepresence network preparation software (AFAIK), is the old tool IPT. This tool will test your network deployment to check configurations appropriate to support the crossing of firewall solutions Cisco Expressway (I can send you this request separately if you wish).

  Hope this helps,

  Arne

• Video conference will operate without a license server TP and conductor?

  Hi all

  We need POC for video conferencing with Cisco Jabber on desktop. The scenario is similar to that we have CUCM 10.5 running in the trial license and server TP and TP driver running on the virtual machine without a license.

  We will reach videoconference without license server TP and conductor?

  Thank you & best regards

  Louis Nithin.

  Conductor Essentials can run without licenses, it offers all the functions of conductor but is limited to 1 bridge Conference and no grouping, refer to table 1 in the conductor datasheet for more information.

  TelePresence Server requires licenses to operate, you will need to purchase a license for the software, so it can be activated, as well as wallpapers or multiparty license licenses.  Screen licenses are per participant and installed on the telepresence server itself, while the multi-party licenses are either user or conference of base that are installed on the conductor.  Refer to the presentation of the product just above 1 Figure in the data sheet of the telepresence Server about the screen and the multiparty licensing options.