Streaks on CM1312 print

Similar Questions

• Printer Dell 5130cdn - streaking on color prints

  Printing black and white works very well. With color prints I get several streaks running through the entire page. Two streaks are purple and about 1/8 inch in width. There are at least 10 streaks orange 1/16th of an inch or less wide extending across the entire page. The location of the streaks doesn't seem to change much between the impressions. I recently replaced the cartridge toner and drums with new parts from Dell.

  The troubleshooting guide suggests opening a program in the tool box and running graphic printed. I have not been able to find how to start the program from the Toolbox.

  So where should I go from here?

  Thank you

  Rich

  I ended up getting the solution to my problem of Dell warranty service. I didn't know that I had this earlier.

  Inside the front door of the printer, you can find a cleaning tool blue plastic with what looks like a pad of velcro on the end of it. The inside of the door on the front of the printer, under each of the four drums, you'll see a gap of about an inch wide with a blue border around it. Insert the cleaning tool into one of the slots until it stops and then remove it. You should feel a clicking against the cleaning tool when you do this. Repeat 10 to 15 times for each of the four slots. For me, that did the trick. I thought for sure it was the fuser unit, but could not understand way that it did not affect printing in black. Now, I know, I thought wrong.

  Were instructions to do this, that I could find in any case nowhere in the online help or the manual of the printer in the troubleshooting section.

  Replacement cleaning pads come replacement toner cartridges that Dell sells. Hope your problem is as simple as mine. Good luck.

• HP photosmart D7460 print photo with red streaks

  iI have a photosmart D7460 began photo printing with red streaks

  Hello scotholm,

  Welcome to the HP Support forums.  I believe that when printing using your printer Photosmart D7460 he has red streaks in the printed output.

  I have included the publication of streaks or lines in the printed Image.  Please follow the steps in the order presented.

• HP Envy 5530 leaving streaks when printing

  Wen the use HP desk top it with Win 7 and HP Envy 5530 printer all-in-one sound suddenly started leaving small streaks on my printed pages.  How can I fix it?

  Are the dark streaks WISPs in the areas which should be light, or light streaks in areas that should be dark?  The document here can help solve the problem.

• LaserJet CM1312: Network connect fails installation

  Hello

  When you install CM1312 printer on win 10 64 bit it fails on the last step: connect to a network printer.

  It found the printer on the network correctly, but then fails to connect. Network address is correct - PC Win 7 on the same network connects fine to the same address. Win 10 is perfectly up-to-date and certainly 64-bit. Tried to disable firewall and in time actual anti-virus (McAfee) but no difference.

  Any ideas please?

  FMc

  Hello

  I got it work. I tried to install the HP driver downloaded by logging in as an administrator, what seemed like a reasonable thing to do.

  Don't know why, but I got the idea to try a user account. Of course it took me the admin password, but he then to install OK, and now all is good.

  (We wanted to use the HP driver because the driver used by Windows scan does not scan in PDF format).

  FMc

• Photosmart C4400 all-in-one printing problem

  My C4400 faithful is not print properly, don't give me indications of levels of low ink and Solution Center says it is not connected. I have replaced the ink (black) cartridge, but still only get a gray print, lineage. I tried alignment heads and cleaning but no luck. Can someone advise me please?

  Hello

  If I understand correctly, the page is faded and has a streaks on the print, when you try to print from HP Photosmart C4400.

  Kindly click on the following link to fix the problem.

  http://support.HP.com/us-en/document/c01004653

  Although I am an employee of HP, I speak for myself and not for HP.

  -Say 'Thank you' by clicking on the star of congratulations in the post helped you.
  -Please indicate the position that solved your problem as "accepted Solution".

  Kind regards

  Vijay

• Windows 8.1 does not speak for Color Laserjet CM1312

  After you have installed windows 8.1 my Color Laserjet CM1312 printer and pc are not communicating.  Tried several drivers update. They do not install. What can I do more?

  PS this post and his response were separated from the other thread and edited its about. -Hp moderator of the Forum

  We would need to see an error or a Setup log message before we can give you some useful suggestions.  Setup logs is normally displayed somewhere as C:\Users\username\appdata\local\temp with a name of the hp type... install... Newspaper.  If you can find one of those that we then validate and share so we can review and tell you what is happening.

  Otherwise, you have to do your best to clean your computer and start again.  I assume you mean that you upgraded the operating system of the PC which worked previously, not put in place a 2nd accidentally broken computer connect to the 1st old PC.  If this is the case then it is more than probably a file conflict somewhere on the hard drive that needs to be cleaned before installing the new drivers.  I would suggest wiping the machine everything related to the HP printer, starting by the devices and Printers window, the properties of print server and driver tabs and the C:\Program Files directory.  Once all old Referances are removed you should have a good shot at a successful installation when you use the latest software Win8.1 of http://support.hp.com.

• Black ink will not print in my HP C4650

  My black ink will not print in my HP C4650.  Using Windows 7 64 bit.  The parameters indicate the cartridge is 1/4 full.  I tried to change the cartridge and still have the same problem.  There is no error message and I did 6 head cleanings with no luck.  The printer was working fine one day with no black printed on the page on the other.  Someone at - there a solution to my problem?

  Hi 362darts,

  Here is an excellent article to troubleshoot your printer when you have streaked or faded prints, prints without black or other colors, prints with cloudy or blurry text, prints with streaks of ink or smear and many other problems.

  http://support.HP.com/us-en/document/c01675472

• OfficeJet 6500 black vertical streaks

  Hello

  I just bought this printer and I keep getting a small, not always to the same place, black vertical streaks on the printed page. It seems to happen when I use the two-sided printing unit. It will print the streak on the front page - not in the back.

  Help would be greatly appreciated (I already tried cleaning cartridges).

  Thank you.

  Denis

  Hello

  It seems that part inside of the unit of the duplex unit took little ink and now is burrs on pages that pass through the duplexer. The best idea is probably to get this duplexer to a service of HP, so it gets cleaned up.

  Before that, you can try print a print job duplex of 30 to 40 empty pages and see if this clears the ink.

• HP Color Laserjet: HP Color LaserJet - lines/stripes

  Hello

  I have a HP color LaserJet and I get a lot of lines and streaks on my printed pages.

  I also note toner inside the printer and my printer seems to take cleaning cycles more than before.

  Thank you!

  Although I work for HP, my posts are MY opinion and not those of HP.

  I would recommend some of the things

  First of all, make sure that your firmware is up-to-date, go to the page software and drivers on HP.com download and install the latest firmware available for the printer.

  Then, make sure that the toner collection unit is not complete

  Finally, print a cleaning of the control panel of the printer page, normally, you should select the following text in the menu:

  • Maintenance of the unit
  • Calibration / cleaning
  • Cleaning page

  You can also view this document as well.

  HP Color LaserJet Enterprise M552, M553 and MFP M577 - lines/stripes, toner and cleaning cycles dust excessive

  Hope that helps.

• DeskJet 6940 ink black smudges on page some time after the change of the cartridge

  Ink started smudges on the printed page, not immediately after I changed the cartridge ink, but after about 50 leaves.  Some leaves have small lines perpendicular to the printed lines as was ink on the rollers.

  I opened the printer and wipe excess ink above the bottom of the grey cables and off the coast of stainless steel rod that runs through the Interior.

  Someone at - it ideas?

  With our thanks

  Hello NHarchivist,

  I see this is your first visit with us on the HP Forums. Please, let me take a moment to say 'Welcome. '

  I hope you enjoy your experience!

   

  To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I see that you have some problems with the smears and streaks on the print-out.

  Please click the link which helps out ink drool or streaks.

  Please do not hesitate to write me again if you have any questions or concerns.

  If I don't get an answer from you today, I hope you have a fantastic weekend.

   

  See you soon,.

• OfficeJet Pro L7780: Officejet Pro L7780 missing of the vertical lines on text & photos

  Everything that I try to print has lack of vertical lines, text or photos. Happens if I print from my computer or if I try to copy a page directly to the printer. I went through the troubleshooting page full... the ink is all well heads, all good impression. Whenever I try to run a printer align it does not end the page. Whenever I have nothing he's trying to align printer print when its done & still cannot print the entire page. Gives me an error and says to check my documataion. I checked the book with my printer & there is nothing in this whole problem.

  Help, please!

  Hi @LockGal,

  Welcome to the Forums of HP Support!

  I see that you are having problems with your HP Officejet Pro L7780 printer aligning and printing vertical lines. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand the frustration that this must be for you. Looks like there are two separate issues. When the printer clean print heads and not properly align itself, this indicates that there is a problem with the cartridge, the print head or the line break. For vertical lines, it is usually independent for cartridges and print heads (not being is not a print quality problem). The paper type and print settings might be the problem.

  To help determine the cause have you used this document: troubleshoot print quality HP Officejet Pro L7500, L7600, and L7700 all-in-One Printer Series?

  Use the document in the order will help you determine if the print heads need to be replaced. If so, please contact HP.

  Please confirm that the vertical or horizontal lines?

  NOTE: are not replace the cartridges and printheads for vertical streaks in a print. Instead, check the paper as directed earlier in this document, or search for a document that addresses this issue. Vertical streaks on copies can often be fixed by cleaning the scanner glass.

  • L7300 of HP Officejet Pro L7500, L7600 and series L7700 each - vertical stripes, lines or streaks on Copies, faxes or scan

  If you have completed all the above steps and your product still has a problem, service the product.

  Contact HP for service in all countries except Asia-Pacific.
  First, check your product warranty to check your warranty printer status and then go to contact HP support to find an authorized dealer or to schedule a repair.
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• HP Photosmart AIO 3310 and 6250 printers - roller cleaning

  Hello:

  We have two HP Photosmart all-in-One (AIO) inkjet color.

  (1) 3310

  (2) 6250

  They both take the same type of printer HP (02) cartridges.

  Internal printers alike... the way the smaller rolls - and the largest main-roller rooms.

  The ink cartridges are fixed in place and are far from rolls.

  They are not lying in a basket that runs through the length of the main roller.

  How do the hail-and-hand several roller cleaning when globs streaks & and/or appear on printed documents?

  Each ink cartridge can be removed and cleaned separately, but how do I clean the rollers?

  I don't see any release mechanism that would allow the roller Assembly to be removed and cleaned.

  The rolls can be rotated manually on site without disturbing the other things, like the alignment or synchronization?

  Thank you

  DaleB

  I'm sorry that you are having this problem with your printers. Here a link to a document on how to clean the rollers on the Photosmart 6520. He advised a do spin the reels manually in step 4 of the document.  Also, I am providing a link to a document that deals with images streaked in this printer that you can use to solve the problem of image beyond quality to just clean the rollers.

  The Photosmart 3310 lacks a separate document dedicated to the roller cleaning as the printer you have. Solution 4 of this document will show you how to clean the rollers of this machine. He will advise manually rotate you also the rollers in this product too. After cleaning, I'd have the printer clean the cartridges in the menu on the front panel.  I hope this helps.

• HP Officejet Usermanual & maintenance guidelines

  Hello

  I have the HP Officejet 7110 (NOT the all in one - printer only) and I am struggling to find an operating manual pdf that don't relate to the all-in-one.

  Ideally what I'm hoping to do, is be able to repair the machine via the software, if there is a way to clean the machine outside the usual HP Utility.  I think I have streaks on my printed sheets (only really when a lot of coverage) and the normal cleaning options do not work.

  Appreciate your help.

  Concerning

  Fuchsia

  Hi Fuchsia,

  For the Officejet 7110 printer user's Guide can be found in the following link:

  http://h10025.www1.HP.com/ewfrf/wc/manualCategory?cc=us&DLC=en&LC=en&product=5327475&task=&

  You can also follow this document to address these issues of print quality:

  http://support.HP.com/us-en/document/c03584225

  Kind regards

  Shlomi

• HP deskjet 5650 WWindows7 pass

  I've noticed that when we had to switch from windows xp to windows 7 my HP Deskjet 5650 printer had one which I believe is a new driver. in the name of the printer, there was an addition (HPA). Since then, I noticed that my impressions are not as good quality and noticed that unlike before I use to get a new window that would come to the top when I would print telling me my ink level. I don't get more and do not know if I need to change the ink cartridges out.

  Hi jledgewood,

  The only way to tell now if the ink is low is if your printed pages are missing, lines or points or streaks appear, the print cartridge may be low on ink.

  Thanks again for your time.