Similar Questions

• Cannot connect to my Satellite A210 adapter for access point

  Hey everybody...

  I have a little problem with my wireless. We have some books and access point. Everyone can connect to access point except me. I have the Satellite A210-127. Do you know where is the problem? How can I connect to the access point?

  Thank you

  In a first time, you must activate WLAN antenna correctly. Upon first use WLAN switch and set it TO position (the LED will be ON). Next step is to use the FN + F8 key combination. Don't forget THAT WLAN is enabled.

  After this use please ConfigFree radar to see if the access point is visible for your laptop.

• DHCP option to set the controller IP for Access Points (Airespace)

  Hello world.

  Does anyone have an idea to specify the controller using DHCP options.

  We use:

  -Controller AIR-WLC4404-100-K9

  -AP-1010-AP-5312 poinst access

  -Server dhcp DHCPd ISC 3.0.1

  Newspapers on DHCP server indicates that access points become the IP addresses, but the controller information are not "read" / "included".

  In the productive environment, controllers will be redundant.

  So far, we couldn't sucsessful with eighter of these configurations:

  Block i. using VTL:

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/products_quick_start09186a00805100f5.html#wp49287

  subnet 10.50.107.0 netmask 255.255.255.0 {}

  option subnet-mask 255.255.255.0;

  routers option 10.50.107.1;

  option domain-name-servers 10.20.51.11, 10.20.51.12;

  option vendor-class-identify Airespace 1200;

  the option dhcp-client-identifier 0xf1, 8, 10.20.51.254, 10.20.51.249;

  DDNS-updates

  DDNS-rev-domainname "in - addr.arpa.";

  DDNS-domain name "xxyy.local.";

  default-lease-time 28800;

  range 10.50.107.101 10.50.107.200;

  }

  II. using the DHCP Next-Server option:

  subnet 10.50.107.0 netmask 255.255.255.0 {}

  option subnet-mask 255.255.255.0;

  routers option 10.50.107.1;

  option domain-name-servers 10.20.51.11, 10.20.51.12;

  Next-server 10.20.51.254;

  III. use of Header Information Option 43 described such in DHCP Manual:

  WLAN-apc code 60 option = text;

  ip address wlan code option 43 = controller;

  subnet 10.50.107.0 netmask 255.255.255.0 {}

  option subnet-mask 255.255.255.0;

  routers option 10.50.107.1;

  option domain-name-servers 10.20.51.11, 10.20.51.12;

  option wlan-apc "Airespace.AP1200"

  option wlan controller - 10.20.51.254;

  IV. using header to the DHCP server information:

  class "-classes of suppliers ' {}

  vendor-class-identifier option match; }

  {"Airespace.AP1200" subclass "-classes of suppliers '}

  Next-server 10.20.51.254;

  }

  Does anyone have a working (using the SAI?) configuration or advice?

  Best regards

  Jarle Steffensen

  Yes, finally got it work.

  I just followed this guide:

  http://www.Cisco.com/univercd/CC/TD/doc/product/wireless/control/C44/DEP.PDF

  and it worked the first time :)

• Predownload image of access points

  Hello

  I was wondering if anyone can shed some light on the process of predownload.

  According to the WLC configuration guide:

  1. download the new image for the WLC.

  2. change the image again to the backup image. (> startup config backup)

  3 predownload new image for access points > ap image config predownload {primary | backup} {ap_name | all}

  Here I do not know whether to use primary or backup. Is - this view of the PA or WLC.

  I mean

  the main use that means that the main image WLC is downloaded (which is actually the existing image as a result of step 2)

  or

  the primary use means any image I download becomes the main image on the AP

  4 swap primary and secondary image on AP > config ap image swap {ap_name | all}

  5. make sure that all the APs did with the predownload

  6. system HH image reset {swap | non-swap} reset-aps [save-config]

  Do not know what exactly the swap image is here. If one swaps the image on the AP only or on the controller as well?

  I feel, if I followed the guide that my WLC will have the new code as backup and after reset system using the APs swap keyword will return with the new code.

  Am I missing something?

  Thank you

  Krisztián

  Hi John,.

  the WLC both the AP will review the main image to be the newly uploaded image.

  Current/running will be the backup.

  Step 2, you mentioned below (startup config backup) just means that if you restart the WLC he starts from the backup image (which is the 'old' in this case).

  You can check what is the active (running) and the following boot image on the WLC with the command "See the boot", for example:

  (Cisco Controller) > see the boot
  Main boot image... 7.0.98.0 (default) (active)
  Backup boot image... 6.0.199.0

  Then, after using the command 'boot backup config' this will become:

  (Cisco Controller) > see the boot
  Main boot image... 7.0.98.0 (active)
  Backup boot image... (default) 6.0.199.0

  Thus, 'start-up' config backup will not backup image to become main... the WLC will start just from the backup image.

  On the command 'config ap image predownload' on the WLC, the main / backup is from the point of view WLC:

  (Cisco Controller) > predownload config ap image?

  Predownload primary an image to a Cisco of the main image of the controller access point.

  Predownload backup image to a backup image of the controller Cisco access point.

  I hope this helps.

  Kind regards

  Federico

  --
  If this answers your question please mark the question as "answered" and write it down, so other users can easily find it.

• Tunnel traffic through the Access Point

  I "tunnelenabled" in the parameters of Access Points of JSON: true;

  And on the Access Point associated connection servers config guide recommends not allowing the tunneling.

  The end result is that the traffic is going through the Access Point and not crossing does not connect to the server. The client wants to keep the absolute minimum for the ports open between the objects, so I want to tunnel traffic from the Access Points through the connection to the server, and then click the virtual and physical machines internal who installed the agent to view. Even when I check the options of tunnel on the login server it always appears as if traffic is bypassing the broker for the connections and go straight to the agents.

  
  

  What the configuration change that I do have all the traffic goes through the access points and associated connection servers?

  
  

  Thanks in advance for any help or suggestion-

  
  

  J

  After a lot of trial and error reduced us to certificates that we created for Access Points. HTML5 Blast Bridge did not have other names of the object in the cert. Once we gave them a cert that had the URL and not the SAN (subject alternative names) with the real access Point server names that Blast started working again.

• Had to reinstall my computer Dell laptop n5030 and now I need to recover dockport and access point for webcam

  Hi you all. I have a computer with webcam dell laptop n5030 integrated. It crashed and I had reinstalled it. now

  the dockport disappeared, so is the access point for the webcam. How to retrieve both. can anyone help?
  Original title: rice J J from Mobile

  Hello

  Find the latest drivers and software for your Dell model and the operating system on the link drivers Dell.

  Then download and install them.

  http://www.Dell.com/support/drivers/us/en/04/DriversHome/NeedProductSelection

  See you soon.

• On my user account on my labtop when I click on a program, such as mozilla firefox, it happens 'windows cannot access the specified device, path or file. May not be the appropriate permissions for access you point. "Please help

  On my user account on my labtop when I click on a program, such as mozilla firefox, it happens 'windows cannot access the specified device, path or file. May not be the appropriate permissions for access you point. "This message appears for firefox, AVG, Windows live messenger, windows MediaPlayer etc.

  I can access my documents, Panel etc. and everything is there, but it won't let me not get access to the programs.

  Also when I go to click on itunes and open office it happens "this file has no program associated with it for performing this action. Create an association in the set associations Control Panel.

  Given that I was able to access control panel, I was able to create a new user and use it for now to send this message and all programs have worked on it and I was able to check for the presence of viruses on the Avg on this and everything was clear.

  Could you please explain whats wrong and tell me how to fix this please: D thanks

  Hello
   
  1. don't you make changes before the show?
  2. is the computer is joined to the domain controller?
   
  You can not start any application on a client computer that is joined to the domain controller. When you try to start this type of application, you receive an error message similar to the following:
  "Windows cannot access the specified device, path or file. You can not have the appropriate permissions to access the item.

  This can also occur if the user account is damaged. If the computer is not connected to a domain controller, try the following steps.
  1. connect to another user account and create a new user account to fix the damaged user account.
  For more information about creating a new user account and the fixing corrupt user account, visit this link: http://windows.microsoft.com/en-US/windows-vista/Fix-a-corrupted-user-profile
   
  Previous post the results in more detail, so that we can help you further.
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Replacement for Cisco AIR-AP1120B Access Point.

  Since the AIR-AP1120B is no longer available (new) what replaces it?

  The 1120 is replaced by the 1130.  The 1130 will be replaced by 1140.  You can always buy the 1130 and 1140 is available since mid-2009.  The main difference for both is that the latter, 1140, supports 802.11n.

  Point of access Cisco Aironet 1130AG 802.11 A/B/G series
  http://www.Cisco.com/en/us/prod/collateral/wireless/ps5678/ps6087/product_data_sheet0900aecd801b9058.html

  Cisco Aironet 1140 802.11 access point N series
  http://www.Cisco.com/en/us/prod/collateral/wireless/ps5678/ps10092/datasheet_c78-502793.html

  If you find my post helpful somehow, please do not hesitate to note.  Thank you.

• My Canon PIXMA MG6320 will support two computers with two different access points?

  I have a laptop connected to the router and modem satellite exceeds at home and a laptop connected to a router/modem with internet service from Verizon LTE wireless in the same House.  I would like to print on my printer Canon PIXMA MG6320 of two laptops.  Is this possible?  Whenever I try to connect my printer to a second access point, it rolls too one that was already there.

  Thanks for confirming my suspicions, merrymary247.

• LAPN300 - the best configuration for 3 access points, while using the same SSID

  Hi all

  What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?

  I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.

  What do you think? What is the best way or do, or could suggest you something else?

  As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network?  Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature?  Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?

  I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.

  Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.

  Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.

• using the wrt54G as access point WiFi for iPod

  I have this Setup:
  (I'm in a trust of a larger network LAN].

  [Campus network: 192.168. *. *]
  ------------------------------
  |
  + [local switch]
  --------------
  |
  + various machines (in 192.168.10.xxx)
  + Pc1
  + pc2
  + ...
  + [Linksys WRT54G] (for WiFi)
  ----------------
  |
  +--> iPod
  + (4 other local unused ports)

  The WRT is configured in Bridge mode and all can see the Internet, but the iPod can not see the PC, unless they are connected on the subnet of the router.

  I think that in this configuration the WRT does DHCP and creates a subnet and then NAT for them to get access to the outside. So the inside can out, but outside may not participate. This means that the applications hosted on the PC iPod cannot interact with the WiFi iPod.

  I want the WRT to act as a bridge and be transparent to the local network & PCs.

  This seems to be a simple installation, but I couldn't sort through the DMZ, router, and help the other possible approaches?

  The answer is 'no '. As far as Linksys are concerned, a router is a router and an access point is an access point, it is because they have two very different functions.

  Concerning

  Fred

• Upgrade license 4402 for additional access Points

  You can apply the L-LIC-WPLUS-25 to a 4402 to enable multiple access points? Or are the 4402 models all locked in their designated access point license?

  Thank you

  -Con

  Hi Con,

  Unfortunately not :(

  The number of support of the AP is "hardcoded" on the WLC model and is not expandable up to 5500 series.

  See you soon!

  Rob

• RV180W add the access point with itinerant support

  I have a client with a RV180w the latest firmware running.  We currently use the router as a router and provide wireless access.  We want to add a wireless coverage and I'm interested in our options.  We have a network unifying ethernet that we could use to give the new connectivity LAN AP.  Can buy us another RV180W and use it in AP mode and roaming wireless connectivity.  The customer wants a guest and business WLAN so we'll use the VLAN of the router.  How we set up the new AP?  Should we use WDS?   If we use WDS, can we still use WPA2?  Thank you for your help.

  Hello, Mr. Carl,.

  Yes is possible to use WDS and WPA2 at the same time.

  The master of accreditation will be setup as a RADIUS server to authenticate the other access points, while clients use the WPA2-PSK, which occupies the same on each access point.

  Let me share with you the information found on WDS and the configuration of basic, found on the guide me section.

  WDS configuration:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=ea8660ccb0cf4ae99cebfafd4303cdc1_WDS_Configuration_on_RV180W.XML&PID=4&FCID=&fpid=&slnid=13

  RV180W configuration:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=dd5990ef4ad947ae89da5c3e0b8bd985_Wireless_Configuration_on_RV180W.XML&PID=4&FCID=&fpid=&slnid=4

  If this answer is satisfactory to you, please mark it as response.

  Diego Rodriguez

  Cisco network engineer

  Thank you

• Remove the secondary controller and tertiary high availability for each access point

  I want to remove secondary and tertiary sector controller of high availability for each access point. I have more than 900 APs associated with a Version of the WLC 8510 8.0.121.0 software. What is the best/better way to remove secondary and tertiary controller?
  Or I can create a model first. We use version 2.2

  Hello

  Easiest way:

  Yes you can do this by using the first Cisco Infrastructure, you can create a Setup AP Lightweight model to specify the name of the PDC and the IP address and specify an empty value (choose the first empty option in the drop-down list) and 0.0.0.0 for the secondary and tertiary sector controllers.  Then you can apply this model to the AP, and she must remove (virgins all) values for these fields.

  Long way:

  Yes there is no clean way to remove it from the CLI. you need to manually remove each on the AP.

  Concerning

  Remember messages useful rates

• WebVPN - error: access method is not supported for the capture of WebVPN

  I'm watching a capture of webvpn on the SAA. I start the capture:

  test type webvpn user capture (entering a valid user name)

  Then I connect to the ASA to try to see track with "Using a browser to capture displayed data" as described in the setup guide.

  https:// / admin/capture/test/OCAP

  After login, I get this message in the browser:

  "Error: access method is not supported for WebVPN capture."

  If I stop the capture (capture test) before you try to connect, the error in the browser is:

  "404 not found".

  The/admin/capture/test/OCAP requested URL was not found on this server. "

  Any ideas greatly appreciated. Thank you!

  After some research, I finally found it

  DOC: Webvpn catches are recorded only in zip format

  
  

  CSCtg79320

  Symptom:

  WebVPN captures are only saved in zip format.

  Conditions:

  According to the following doc:

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/WebVPN.html#wp1153077

  WebVPN captures can be recovered in the pcap format using the browser, which is incorrect. The document must be corrected.

  Workaround solution:

  N/A

  Thank you for your time and cooperation

  Portu.

  In case you have any other questions please note all useful messages and mark this question as answered