Tecra 8000 - hub USB 2.0 does not

Similar Questions

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Is there such a thing as a USB wireless, that does not need USB cable upstream that goes into the usb slot in the main computer?

  Is there such a thing as a USB wireless, that does not need USB cable upstream that goes into the usb slot in the main computer? I've looked everywhere but I can't find one. I hate the son, and I try to clear my desk of as many people as possible.

  # USB is cable only.

• USB 3.0 does not work on HP Pavilion 23 g010

  USB 3.0 does not work on HP Pavilion 23 g010. Can not find the driver from HP site that works. Can anyone help please because it is a new computer? Windows 8 is installed, but owner downgraded to Windows 7. I tried the drivers that are supposed to work and the said error box "this computer does not meet the minimum requirements for installing this software"... don't know what to do but would appreciate greatly any input...

  Hello:

  Your model has an AMD chipset and processor.  Therefore, the Intel chipset driver will not work.

  First, install the AMD chipset driver and restart.

  You want to download the 49.7 MB file.

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064

  If that does not install the USB 3.0 drivers (see the file they are included), then download and install both of these drivers and USB 3.0 will work for sure in this way.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359417&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_123787_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359417&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_118744_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  If there is any other drivers you need for this model, please let me know.

• USB/bluetooth mouse does not.

  I have a mouse mobile memory 8000 who, for some reason, does not work. The issue began yesterday after I used WUBI to install ubuntu alongside vista. My mouse did not work when I booted into vista. The cursor does not move and it does not meet the clicks. I tried wire and modes bluetooth with the same results. I uninstalled and reinstalled an updated version of intellipoint. I uninstalled all associated mouse or eventually the mouse related drivers I could find through the Device Manager and let them reinstall a reboot. The computer recognizes that the mouse is there, he says that everything is working properly and up to date. Any ideas on what could be the cause?

  Edit: I also tried to uninstall Ubuntu without effect. IntelliPoint and device management, yet all drivers are working and up-to-date and the mouse does not work as well. Mousinfo using no movement or mouse clicks are detected by it.

  Hi khukuri,.

  It is possible that the incorrect mouse is selected in the IntelliPoint software.

  See the Microsoft articles and try the steps mentioned below.

  The problems with the mouse button or scroll the parameters

  http://support.Microsoft.com/kb/303091

   

  Troubleshoot the incidents of the response to the mouse or wireless keyboard

  http://support.Microsoft.com/kb/838398

   

  Troubleshoot a wireless mouse that does not correctly

  http://support.Microsoft.com/kb/321122

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Is there a download from Microsoft which will create a bootable usb media that does not have the drivers?

  Original title: A bootable Windows 7 media

  I work on a Lenovo 2-in-1 with Windows 7 (for games) and 10 (for a normal use) Windows to dual-boot. I created a USB stick with Windows 7 Pro (64 bit) of a legitimate Windows 7 Pro disc. The computer starts on the usb device and plays normally, however, one of the steps asks a driver for cd/dvd and this 2-in-1 (Lenovo Flex 3) doesn't have a built-in CD/DVD. All other drivers are located in a folder system. My question is, given my key Windows 7 can I create a new bootable media that does not demand drivers? Is there a download from Microsoft which will create a bootable usb media that does not have the drivers? I know that I can reinstall the drivers manually after the installation.

  Thank you

  Matt Armshaw

  Windows 7 or Windows 10 come preinstalled?

  If you install Windows 7 on a system that is preinstalled with Windows 10, you must do the following before:

  -Disable the secure boot UEFI

  -Disable the quick start

  -L' install created media can be corrupted.

  How to: Dual Boot Windows 7 or Windows 8 with Windows installed 10 first

  I suggest that you try to create another bootable copy.

• 16GB USB flash drive does not not on Satellite L300-11F

  Hello

  I have a laptop Toshiba Satellite L300-11F. It comes with 2 USB ports.
  I have a pendrive plus 1 GB and all recently bought a Maxell 16 GB USB key.
  The USB works flawlessly at work, desktop pc, but doesn't seem to work with the laptop.

  I managed to use that only once since the USB port of the laptop simply does not recognize.
  I can tell that the Red led does not Flash and the Flash DRIVE is not accessible.
  I tried to use the hub USB Toshiba provided, no chance either :(

  2 USB ports are ok I use mouse, digital camera with her.
  Is the 16 GB USB key, it works perfectly with other machines. * desktop pcs *.

  I'm missing a few USB drivers or what is the problem?
  Please help I need to be able to use the device on the laptop too.

  Thank you!

  Blaze

  Can you use a Flash DRIVE with a lower capacity on the two USB ports?

• Tecra S10-128-Vista 32 - eSata does not work?

  Hello everyone,

  I have 2 external hard drives USB\eSATA, an AKASA 3.5 and a VANTEC 2.5, they work fine in USB mode, but in eSATA, I get no response from the TECRA S10-128.
  The wealthy drive 3.5 does not need external power, the 2.5 power, when I connect the cable, is not a led flash.

  The OS is 32-bit previously connected original Vista.

  All ideas, King regards,
  FERRETE

  Now, I realized that the Tecra S10-128 is sold only to the Portugal! Here you can see what losing bean you'v: p.

  http://PT.computers.Toshiba-Europe.com/innovation/product/Tecra-S10-128/1060596/toshibaShop/false/
  .

  .

  Hello

  > They work fine in USB mode, but in eSATA, I get no response from the TECRA S10-128
  I was a little confused m
  As far as I know that the laptop supports the eSATA/USB combo port it s on the left and it conforms to the USB 2.0 standard.

  A (HDD) connected eSATA device cannot be recognized unless it s connected to the eSATA port, while the phone is in standby or standby.
  In this case, disconnect the eSATA device and reconnect it while the Tecra is turned on.
  Usually, it takes about 10 seconds until the eSATA device would be recognized by the laptop. Don t try to disconnect and reconnect the drive before this period has elapsed.

  In your case, I would check the BIOS settings.
  The second page of the BIOS provides eSATA settings. Check it out.

  I also recommend the installation of the OS switching device Configuration.
  This can be done as well in the BIOS

• Satellite A100: USB and Modem does not

  Hello!

  My name is Clarisse and I have a Satellite A100, which I use for school. I'm having a problem with its usb ports and modem.
  When I try to connect to the internet, he just say he of no tone and tells me to ensure that lines are connected, who they are and the phone line works certainly, as I checked with my PC and I also checked the phone if it was busy, it wasn't.

  I then try again and a window appears and says that there is something wrong with my modem, how can I fix?

  The other issue is my usb ports who refuse to work, they can't recognize anything I plug (for example, bluetooth adapter, flashdisk, ipod) even though they are installed!

  However, the strange thing is that when I plug in my printer it connects and does its job:(je suis tellement confus et scolaires est devrait commencer bientôt.)

  Can someone help me please?

  Thank you
  Clarisse

  Hello

  In my opinion the modem connection does not work due to the modem settings.
  Go to Device Manager and select the properties of the modem.
  Please select the Modem tab. You will find the option "wait tone before dialing." You must disable (uncheck) this option.

  I guess that the USB ports cannot recognize the external USB ports because of the power.
  The USB ports provide 500mA. It is a standard USB. If external devices use a power greater than 500 ma, so it is possible that the device may not be recognized.

  In such cases, the USB hub with an external power supply can solve these problems.

• Satellite Pro L20-212 - USB 2.0 does not work

  Hello

  I own a * Satellite Pro L20-212 *, * Windows XP (SP2) is installed, but USB2.0 does not work *. I see nothing on USB 2.0 in the Devicemanager and the speed of the USB 2.0 devices attached is at the level of the USB 1.1.

  I don't know what information is needed to help me with this problem as it should normally work on my laptop (and I know that the laptop has USB 2.0 ports).

  What I have to install a special driver to use USB2.0 or is there any software on my laptop that I need to activate?

  Thank you very much
  Frank

  Hello

  Did you install the image on the Toshiba Recovery CD? This image contains the Windows operating system, Toshiba drivers and additional utilities. After installation, everything should work fine, and also the USB ports should work also.

  The USP ports, you can find in Device Manager in the serial BUS controller universal section. Open the tree and check if there is some yellow exclamation points.
  Then try to remove the Device Manager, the controllers and the USB hub and restart the laptop. After restarting again the OS should recognize USB controllers deleted again.

  I hope that this accelerated procedure will help you.

  Greetings

• USB 2.0 does not work in bootcamp Windows 10

  Hello

  I try to use my USB 2.0 USB drive on my MBP 13.3 "in bootcamp Windows 10 and it does not appear in windows Explorer. The USB key is displayed in the device however Manager. I tried my hard drive that is USB 3.0 and it works fine, but the USB does not work. I have tried many different solutions and none seem to work including physical relocation and replacing the USB name i.e. H: U:. In disk management, the device is there but says "no media" below.

  Someone at - it suggestions as to how I can get the USB appear in Windows Explorer and access the files?

  Bravo to all the answers in advance.

  the device is considered that the format is not. In some cases shaped on the Mac in Fat32 or ExFat is not readable under Windows. Reformat the Windows Fat32 or ExFat Device Manager device, it will destroy the data and mount the drive. In turn the unit may become unusable which can occur over time.

• The right side and express USB card reader does not work

  Hello

  The USB 3.0 right on my rMBP does not work. I have can´t to connect any device to this side. No connection or power.

  Express card reader doesn't work or the other. Finder or disk utility will not show map of mountain.

  I can´t find the card express under system reports reader.

  I ran a test for diagnosis of Apple without any problem.

  I have reset the SMC & LANDAU.

  I reinstalled the operating system without success.

  Anyone who knows how to fix this?

  MacBook Pro with OS X El Capitan 10.11.5, Retina display

  Can someone help me here, please!

  Based on what you have tried and if can't see any device in disk utility, you are dealing with a hardware problem.  Your best option is an appointment at an Apple store for a FREE genius bar.

  Ciao.

• Gigabyt USB adapter works does not win10

  gigabyt USB adapter does not not qin 10 / 64

  HP has not posted any drivers for it. It appears in Device Manager? All other usb devices work?

• Portege R500 - keyboard USB Legacy support does not work

  I have a Portege R500-124

  I use it to dock in the office and the lid is closed, so I need to enter a password for DriveCrypt and generally control the boot/BIOS from a USB keyboard. But no matter what I set the setting that is inherited from the USB in the BIOS, the USB keyboard does not work. I tried the keyboard connected directly to the R500 when undocked and it's all the same. I also tried BIOS 1.6 and that's all the same.

  USB keys are working and I can boot from them, but no work of measures (for example, F12 to choose the BOOT device) keyboard - the R500 doesn't seem to have the functional USB keyboard support until an operating system (Windows or Linux) has started.

  Any ideas?

  Ian

  > .the R500 does not appear to be the functional USB keyboard support until an operating system (Windows or Linux) has started.

  I can't confirm this, but I'm afraid you're right about that.

• Tecra M9 and M10 wheel Volume does not not under Vista

  Hello

  I hope that someone can help me, I'm Vista using Microsoft Deployment Workbench deployment for Tecra M9 and M10 material and the volume knob will not work. I added the drivers of Toshiba in Deployment Workbench, while they are presented the machines via Plug n Play, volume button do not work. I also deleted the drivers of Deployment Workbench and installed the drivers manually on the machines, this installs fine, but volume knob will not work. I have two development servers, Win Server 2003 and Win Server 2008, the two do not run successfully the pilot slots.

  If I deploy a standard Win Vista Enterrprise 32 bit OS of DVD hardware, with any driver when it is installed, the volume wheel works. I can then manually install the audio driver and the volume button still works. But if I deploy the same exact DVD based OS of Deployment Workbench, the volume knob does not work?

  Any help would be greatly appreciated, as this is doing my head and holding up the deployment of the new image.

  Thank you
  Paul

  Maybe you are trying to install the driver Audio of M9 M10 or vice versa?

  You install the driver Chipset Intel and value-added package first? (this is important)