Tecra M9: Toshiba BT & WLan helmet - preparation of pilot error

Similar Questions

• PC Toshiba laptop tecra9100 receive a PXE - E61 error

  I have a Toshiba tecra9100 labtop and I get an error PXE - E61 message. It says Media Test failure, check cable (it is a laptop computer, it doesn't have the cables that I can see). This occurs while the system trying to boot. It was a gift from a friend, so I don't have the system disk, which he continues to ask. I went to the Toshiba site and they said to change the boot priority but none of the combinations that gives me the laptop work. I also called them and they said that there is an error in Windows. Is it possible that I can get a Windows XP system disc, or is there something else I need to do?

  * original title - I received a PXE - E61 and PXE - M0F my *.

  Hi Arochellet,

  These errors are not related to Windows, this would happen either by an incorrect setting in the basic input/output system (BIOS) or a bad boot as a bad hard drive device.

  Make sure your hard disk is configured and detected correctly in the basic input/output system (BIOS). Your computer should list an installed hard drive either the title of the home page or the page of the basic input/output system (BIOS) disks.

  Check the boot options are set correctly in the BIOS, almost all BIOS configurations must contain options specifying how your computer boots. For example, most computers should have their installation options to start similar to the example below.

  -Floppy drive
  -CD player
  -Hard drive

  Note: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  I suggest that you take the laptop in a store local tech to check any hardware malfunction or internal connections.

• Cannot connect Tecra A9 to my WLan router

  Hello

  Can someone help me please.
  I have a Tecra A 9 series with VISTA as an operating system. I have problems with my wireless connection.

  If the switches and wireless lights are on, I can always connect to my wireless router. I can only connect to the internet via the wireless when the ethernet cable is connected to the laptop for about five minutes.

  It remains lit when the cable is disconnected, but if the computer goes to sleep or restarted, wireless connection is lost unless the s cable reconnected. Although the wireless light will be orange instead of green?

  I'll be very grateful if someone can offer me solutions please.
  Thank you

  In your case, I'd do a BIOS and driver update. You can find updates on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  In addition, test the WIFI connection without security settings. This means hidden SSID, MAC address filtering,
  And don t forget to check if the router and the laptop using the same standard WLAN.

• Tecra S11: Detection for the Toshiba tool: your product is not found error

  Hello

  I use Toshiba detection tool quickly find drivers for my tecra, but since a month now, the page gives this error
  Your product is not found

  It is not a problem to choose my phone in the new drop-down list, but it was uncomfortable, when it worked.
  Is there a solution for this problem?

  What tool do you mean exactly; Panel display or Tempro?

  As far as I know there is a new version of Tempro reinstall it and check how it works

  PS: since my knowledge only European Toshiba notebook series can be detected by Tempro

• Tecra M5 - Toshiba Power Saver did not do his job properly

  Hello

  After looking for a tool to silence my Tecra M5 awhile, I found an apparently nice application called Toshiba Power Saver. Unfortunately this tool doesn't seem to work properly. I played with the [slider cooling method | http://img200.imageshack.us/img200/8008/powersaver.jpg] (click to see a picture) and here's how it works.

  The cooling method can be set to one of four options: battery optimized Performance, maximum Performance and cooling optimized, where one is supposed to be the quietest, and those of other more noisy.

  Assume that the cpu fan spins at high speed at the start and I do not have anything on my laptop. I move the cursor to the battery optimized setting, click on apply and the fan (instantly) slows down (yay!). Then I need to do something about hunger for a while and finally the fan turns up the noisy power level. I then doing nothing of the brand-new, but the fan is like that * ever *. The processor is as cold as ice, the air is blown could freeze the fingers, but the fan spins like crazy to wake up my neighbours on the road.

  I'm really sure that the cpu is cool? Yes. Why?
  Because when I move the slider for Performance affecting now and click on apply the fan slows down (right) and remains like that until I start working on something new. Then I stop doing what I was doing and the continuous spinning fan * ever * once again.

  So I change the method of cooling for battery optimized setting back again once, click on apply and the fan slows down... and so on and so forth, stuck in a vicious circle.

  The key to success here is keep pressing the button apply, which the Power Saver application should do from time to time and not me and not forgetting what it is here for.

  What is the problem with this app? Is there a fix available (or alternative)?
  The version I have is 7.11 and runs on XP Pro SP3.

  Hello

  What about your ad here?

  TOSHIBA Power saver is tool Toshiba use for years and it is preinstalled on 98% of all models of Toshiba laptops. So, in my opinion, this tool is certainly one of the best and most effective tool designed by Toshiba.

  Over the last 10 years, I have worked with many Toshiba laptops and I used this tool on each laptop to optimize my work. Mix between the good performance of the processor and method of cooling level offers enough power for each working day and with a low level in the method of cooling laptop runs pretty quiet.

  Maybe stupid sounds now, but I have noticed that the Portege notebooks are, perhaps, more sensitive and using tool electric saver you cannot have the same effect as on certain portable Satellite and Tecra.

  I do not think that this tool doesn't work properly on your Portege but Portege laptops have a specific design and material may reach a higher temperature faster than on the other laptop models.
  Portege laptops have excellent and powerful material packed in a box of small notebook.
  Sometimes laptop runs quiet and if you just connect the USB mouse the cooling fan starts to run strong enough. A small business can speed up physical activity and if temperature sensors have noticed a higher temperature for a degree C only, the fan control mechanism get information starts to cool the fan turns.

  It is really not easy to tell if there is something wrong or right. My personal opinion is that everything is OK. You can try to talk with the service of Toshiba. Call them and ask for explanations. They should have enough experience with this stuff.

  In any case, good luck!

• Portege R400-600 - Toshiba flashcards - WLAN does not work

  (Toshiba flashcards) menu that appears when you press Fn + Fx - works fine, but the wireless - Fn + F8 has dimmed in the menu item with the commands of triangle on a vertical line with two vertical lines next to him: I think it's the wireless status symbol. It is impossible to turn it on.

  In the same way, the blue LED on the front of the computer that displays the status of the Wireless is definitely off, although the wireless works

  Have tried reinstalling WLAN driver but could not have found anywhere.

  Any advice?

  Hello

  In addition you must activate the antenna switch WLan on the side of the laptop, if you want to activate and use the wireless LAN!

  If the laptop was equipped with BT and Wlan then the FN + F8 toggles between these two work.
  Please don t forget it.

• Re: Tecra S2 - LAN and WLAN available after 5 minutes

  My problem with TECRA S2 is only there 5 minutes before my LAN and WLAN works! I've tried everything (updated BIOS, LAN, Wirelles etc...)
  Does anyone have an option to solve my problem?

  Thank you.

  And what happens if you reboot your router? You must wait 5 minutes yet?

• Toshiba 42L7453DG - WLAN connection problem

  Hello

  I just bought this TV and I have a problem with the wifi connection. Television can see my network, but after entering the password cannot connect to the AP. Can someone tell me where is the problem?

  Concerning

  There may be a problem with the support of Wlan (WEP/WPA/WPA2 AES, TKIP) encryption
  Can't say for sure what s wrong with the connection WiFi, but I recommend to disable the WiFi encryption for test purposes and try to connect to your TV to open WLan (unsecured).
  It would be interesting to know if you can connect to the device this way TV

• Tecra A9 - Toshiba Assist button doen't answer

  My buttons the "Toshiba Assist:" and the button below that does not also when I use them.
  Can someone help me how I could go about doing work?

  * I've tried use / installation application Toshiba Assist. He tells me to reboot the system, but it still doesn't work after that it had been restarted.

  Thanks in advance for any help I can get

  You n writing t nothing about your operating system installed.
  What operating system do you use?

  If you have installed Win XP a common Module and Toshiba controls must be installed to ensure that all button Toshiba would serve.

  If you use the Vista operating system, you must reinstall the Toshiba value added Package.

  Good bye

• Tecra A - Toshiba Power Saver error after loading the OS

  I have two problems with my XP Pro SP3 operating system

  (1) immediately after loading the OS, I got this error message

  http://photoserver.WS/images/oCVJ4c25d94898215.PNG

  (2) and my job doesn'r to reboot. Stüch Windows HE is shoting down, and I have to manually to swith out of turn.

  How to solve this problem?

  I don't know much about your model, but I think you should update a powerhouse of Eve:

  [Toshiba drivers | http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp]

• Tecra M9 - where the WLan card

  Hi all.

  Can someone tell me where the wireless card is located on the M9 series please.

  I expected under the machine with a quick access panel, but apparently not.

  Where is it and is it easy to get it please.

  Thank you.

  Hello

  I guess the minPCI wireless network card is hidden somewhere under the keyboard.
  You need to remove the keyboard first, if you want to get access to the Wlan card.

  But I wouldn't remove the keyboard, because in the worst case, you could lose the warranty!

• Tecra R850-117: RFBus - device could not be started (error not 10)

  On my Tecra R850-117 (64-bit) Bluetooth does not work; problem seems to be RFBus;
  I tried to make the pilot, but the system answers, this is the real version.

  However, the device can not be started (error 10)
  Any tips?

  I installed also added package like the keys Fn and accessibility does not work on this "new" laptop (there is no test produt before PC out on the market?)

  Hello

  Don t try to refresh the battery BT but uninstall the battery BT the system.

  Then download the CCleaner tool. This tool cleans up the registry and removes all traces of BT of the system.

  After that restart the laptop, download the last battery BT from here:
  http://APS2.toshiba-tro.de/Bluetooth/?page=download-Toshiba and install the BT are turning once more.
  Do not forget that the Fn + F8 would allow the BT Service.

• Re: Tecra S5 - 15 q - monitor display lines vertical and error 43 for GPU

  After about 5 years my Tecra S5 is experiencing problems with its graphics.
  Most of the time the (internal and connected an external via VGA) monitor displays vertical lines, and windows gives an error 43 on the map.

  I was wondering if there is a way to solve this problem, and if this problem could be solved under warranty (although the protohistory of the warranty expired 3 years ago.) .

  In my opinion, it is bad material work and as far as I know only way to fix it is motherboard Exchange. I n t have this model of laptop, but I can presume that the GPU is fixed on the motherboard and cannot be traded separately.

  Fixed under warranty? Of course.

• Toshiba Satellite Pro M30 & Power Saver stop error

  Hello!

  I am struggling with this problem for months... the latest version of Eve on my toshiba satellite pro m30 running windows xp with service pack 1 installed gives a message box with an error message when the stop and I'm unable to eliminate this error. Unfortunately, I can't consider reinstall the system from scratch, because there are many other applications installed and I can't lose the settings for them. I read the forums and realized I'm not one of the problems with toshiba power saver. I'm even lucky to successfully at startup started it! Yet, it hangs at shutdown. It's pretty boring. also, I downloaded all the latest updates of this site for my laptop, including even the bios update.

  I would like the opportunity to be able to download the version without toshiba this site energy saving bug, and I'm sure many other people would appreciate the patch too!

  any comment on that?

  Andrew.

  Hello

  If your laptop is installed correctly it should work well. All the software has been tested. The only reason for your problem may be additional software that you have installed later.

  It is also possible that it may be caused by an Antivirus application. Maybe an application runs in the background? There are many reasons that may be responsible for this problem.

  If you reinstall your Notebook of recovery CD it will not work properly. It is very unjustifiable to write on some versions bug-free. I sometimes have problems with BONES, but almost always after using some freeware.

  Good bye

• Tecra S5: Program crash on the 16-bit subsystem error

  Hi all,

  PC Tecra S5, I remove Vista and install XP but when I want to use some applications or stop app crash. When I want to stop the process, he said the 16-bit subsystem has become unstable.
  I remove almost all programs pre-installed, including Norton (Norton remove tool), clean the registry but without result.
  On the forums a few guys fix this with updated the wow32.dll but in my case does not help.
  How these applications work on another manufacturer (with the same processor) I guess that the problem is with the handling with memory or chipset drivers.
  With Vista is the same problem

  Any solution?

  THX

  To be honest I've never seen this error message and I think it s a problem with Windows XP.
  I put t know if you have installed all the patches available for Win XP or not but I really recommend you update the operating system to the last State.

  A few days ago I installed the XP SP3. It was a beta version, but it works very well.

  Check this possibility.