Tecra S1: Cannot get battery bluetooth or wireless to work
Hello. I have a tecra S1. I bought a friend and don't have is not the original cd. After a fresh install of xp sp2, I followed the order of installation of the drivers from the toshiba site. I tried several drivers for the wireless card, but it is still yellow in the devices. I'm confused as to why there are so many drivers for the wireless card (intel, toshiba, atheros, cisco, etc.), none of them work well? Can anyone help?
In addition, as a result of the bulletin tec on the toshiba site I installed the toshiba bluetooth stack. Whenever I try to open the bluetooth Manager, it does not. Nothing will come up on the taskbar. Can anyone help?
Thank you
Matthew.
Hello
The fact is that these devices are optional on this unit. The laptop also has 4 different wireless network cards. You should be sure that you are using the correct driver.
You suggested that the Bluetooth mouse is connected to the unit. Well, it seems that the Bluetooth works fine, but you have not enabled this feature.
Try using the FN + F8 key combination to activate the WiFi and Bluetooth.
Tags: Toshiba
Similar Questions
-
Wireless router / Internet problems
I am running Windows Vista Home Edition with Security Essentials. I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity. Is there a firewall setting that could cause this problem?Hello
Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
Update your WiFi drivers on computers. How you are positioned in the router? Are there
obstacles in the path?Actually try updating your driver and disabling the network logon.
Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlDownload - SAVE - go where you put it - right click – RUN AS ADMIN.
You can download several at once however restart after the installation of each of them.
After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
manufacturer of system become your backup policies).Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
updated drivers.I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
are almost always old, and you can search drivers manually as needed.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx------------------------------------------------------
Make sure you know the details of connection to your wireless router - SSID and password.
You lose connection when you do and have to redo your logon.
Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
lower left click on merge or delete network locations - REMOVE all instances of your network (and the
others you don't use anymore) - REBOOT. Start - Connect To log on to the network.-----------------------------------------------------
Check this box:
Strange problem with Internet under Vista
http://www.catonett.com/blog/archives/194Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
http://support.Microsoft.com/kb/928233/en-us----------------------------------------------------
And:
Network connection problems
http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
Cannot get my CD/DVD player to work
Cannot get my CD/DVD drive to work because be adjusted back to IE8, it says driver or network connection is not available what to do I please
Hello
Try the microsoft 'fix - it' for your problem below
http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us
and read this information too
-
I installed a Plantronics Voyager legend UC bluetooth headset to my work provided Lenovo ThinkPad laptop computer running Windows 7. The helmet looks like a device in the Panel--> devices and printers. However, it does not show as a device in the control--> tabs sound playback Panel or registration. I need the headset to the playback device for my work-VoIP phone.
I tried to remove the helmet and reinstall, but I can't delete it in the Panel--> devices and printers. When I locate and right click, remove or uninstall is not an option. I went to the control panel--> Manager--> audio video devices and game controllers, which are there and uninstalled. I then unplugged the connector of the headset, and the headset powered off and rebooted. I then plugged the connector UBS back in and turned the headset. The PC began to reinstall the drivers, but the headphones still did not appear in the sound tabs.
I have been all over the internet trying to find a solution to this problem and so far have not been successful. I spent hours on this and it shouldn't be so hard, but it turns out be. I appreciate any help you can provide.
Thank you!
Thanks for your reply Mann. Here's the answer to your questons.
- Were you able to use this helmet earlier on this computer? Answer: Yes, it didn't work and appeared in the reading tabs and the recording of sounds. However, I accidentally deleted it--> sound when I was trying to troubleshoot why I couldn't hear the narration in the course of eLearing played on our intranet via the headphones. I only meant to change the settings so that I could make the speaker/HP the default device. BIG MISTAKE because now I can't get it to reinstall and appear in the tabs of playback and recording.
- Have you checked to connect the headset to any other computer, it works on other computers? Answer: The only other computer I have is an Apple MacBook Pro. I plugged the USB connector to the PC and seem to work although I can't do a one-to-one comparison.
- You said that Windows has started to install drivers automatically after connecting the headset and the computer restarted after the removal of noise, the video controller and game, was the driver installed successfully? Answer: Yes, but it just does not appear not liked as an option in the tabs of playback or recording.
- Other audio devices work fine on this computer? The only other device is the computer speakers and they work fine.
Regarding method 1. I had already installed and run the file MicrosoftFixit.Devices.exe that you provided even if I ran again and this has not fixed the problem.
With respect to method 2. I checked and show disabled devices is checked. The only other devices in playback and recording are speakers/HP and Realtek HD Audio Output 2.
UPDATE! I removed the USB of the headphone connector and plugged into the MAC, and then removed the Mac and plugged into the PC, that is! The helmet now presents itself as an option in the tabs of the reading and recording. Yes! I was able to select it and set as device by default, tested the VoIP phone and it works all! Phew! I was about to give up on the VoIP phone. Thank you.
-
Tecra M4: Cannot get com-port working on Advanced Port Replicator III
Hi all
I bought the advanced III PA3314E-1PRP port replicator but could not get work com-port.
It does not get listed in my equipment manager.
Anyone has an idea why not?Thank you very much in advance!
See you soon
Infinito
I agree with Akuma
(The name says it all) port replicator replicates the available ports on the laptop.
If your laptop does not have this port, then you cannot use it with Port Replicator. -
Tecra M2 - cannot install drivers Intel/PRO Wireless 2100
I have a Toshiba Tecra M2. Drivers Toshiba page for my model lists an update driver for this PC as follows:
Driver Lan Wireless 19/12/05
Intel Windows XP 9.0.2.31 World WideI don't seem to be able to install it, even though I have an Intel/PRO Wireless 2100 in the portable - setup just point out that it is not compatible driver or a device installed. The previous update of the driver:
02/12/04 Wireless Lan Driver
Intel Windows XP 1.6.0.47.W2 World Widereported as installed OK and Device Manager reports 1.6.0.47 as the installed driver.
I understood that the version 9 drivers are more stable but not the driver version 9 applies to my laptop?
Hello
If you check the driver information, I think that you will not know why it does not work. I have the same WLAN card on my Tecra M1 and our cards support the standard 802. 11, a / b. The driver that you want to have is for cards supporting the 802.11 standard, a / g, g.
I tried to install it on my Tecra but the same result.
Don t worry that everything is OK. If you buy a new Intel 2200 g card you can use.
Good bye
-
Cannot get internet connection through wireless network
I have a Sony VAIO laptop that came with Vista 32 bit and went from 7 Home Premium 32 bit. I connect to the internet via my Ethernet via a DSL modem with no problems. When I try to use the edge Intel 4965AGN wireless to connect to my DLink 655 Wireless N Gigabit router, it appears that it connects to the network, but there is no internet connection. Both the router and the edge Intel have the latest drivers and the encryption is set on AES, WPA2-Personal. Some additional information:
I have desktop computer Dell with a DLink USB WiFi and it connects to the network and gets internet
I constantly get the message from Windows saying: Windows has detected an IP address conflict with another computer on the network. I restarted the router several times to no effect.
In network and sharing Center (of course the troubleshooting network said he found nothing) the network appears as a Public and unidentified and it gives me no option to change it to a home network.
I tried to connect to other networks public wireless (hotspots) and I can't connect it
Hello
Something is wrong with the TCP/IP parameters.
Autoconfiguration IPv4 address:169.254.1 52.88
IPv4 subnet mask: 255.255.0.0
Autoconfiguration IPv4 address: 192.168.0.1
IPv4 subnet mask: 255.255.255.0
IPv4 default gateway:This 169.254.1 52.88 is the IP by default Windows assigns when there is no DHCP server, this isn't a working IP address.
The second IP address is the IP address of the Wired card. That is why router conflicted reports.
Configure the two cards for full Auto obtain IP and DNS.
Then do a WinSock and TCP/IP updating.
Type Cmd in the search text box.
Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt. Allow the elevation.
Type netsh winsock reset at the command prompt and press the Enter key.
Do the same process to refresh the TCP/IP just replace the command typed with.
netsh interface ipv4 reset Press enter
netsh interface ipv6 reset Press enter
ipconfig/flushdns press Enter
Restart your computer.
Jack-MVP Windows Networking. WWW.EZLAN.NET
-
Tecra M2 - cannot install the last driver wireless
I'm updating the Intel wireless network driver as my wireless connection does not work.
I downloaded and unzipped the file wlesslan-xp-90231 but when I click on the icon to start the setup happens 'could not retrieve all of the adapter-specific information to perform installation operations. "The following file is not found: setupWLD.ini".
It seems that this setupWLD.ini file has been excluded of zip archive.
Everyone came with this problem and if so what is the workaround?
Hi Jeremy
It s nice that you have solved that problem.
Thank you also for this information because it might be useful for other users.concerning
-
Tecra M3: Cannot get the SD memory and utility boot Format to work
Format SD memory Boot utility does not! (Tecra M3)
SD memory boot utility and install utility Format Software memory SD fine with no problems. But they both then return an error when you try to start a program.Utility boot SD says:
Unexpected error! 00-52-FF02-126 error codeSD format utility says:
Unexpected error! Error code = 0x0034FF02After clicking on this message box appears the window of the program, but there is no drive to select. There is an SD card into the SD card reader slot, but still he does not come to the top.
I run Windows XP pro, office 2003 against Tecra M3.
Help, please! Do you know of any other (free) software to use the brand so a bootable SD card, or how to fix these errors.
Hello
Sorry, but your ad confuses me completely. If you did clean using the delivered OS install why you should install ConfigFree recovery media tool?
TOSHIBA ConfigFree tool V5.00.48 is undoubtedly part of the recovery image and if you use recovery image you should NOT install anything. On this way unit is completely configured.The recovery image contains the operating system, all necessary drivers and Toshiba designed tools and utilities. After the installation procedure and first departure all the pieces of equipment work harmonic if there is no any kind of hardware malfunction.
Only thing you need to do is to install own application you need for work (office or any what editing application) or games for fun with Notepad.
If you have another question please write again.
Good bye
-
Cannot get my deskjet 1050 printer to work as wireless
How do I use my deskjet 1050 printer wireless to connect it to my router? 8 64-bit Windows. He repeats, I need to install wireless connection procedure, but I can't find anything like that. My router is supposed to be able to turn any printer in a wireless network.
Hello
What is your magic router? Based on the specifications of your printer, simply:
Connectivity
HP ePrint ability NO. WiFi functionality NO. Connectivity, standard 1 USB 2.0 PORT If your router was not a magic trick otherwise you need something called print server USB wireless that is similar to one of them:
Kind regards.
-
Cannot get my usb card reader to work because I plugged my new wireless broadband
HI MY PLUG-AND-PLAY DIRECTED BY ABC PRODUCTS USB CARD READER WAS WORKING UNTIL WEEK LAST I CHANGED MY CONNECTION TO BROADBAND CABLE TO CONNECT NEW WIRELESS I UNPLUGGED AND REPLUGED INSIDE BUT STILL DOES NOT?
JOHN SOON
Hi John,.
1 Windows operating system you are using?
2 are you facing issue with other devices usb also?
You can read the following article and try to run the material Fixit and see if it helps.
Hardware devices do not work or are not detected in Windows
Hope this information is useful.
-
Cannot get HP C7280 print wirelessly on OS 10.5.8
Hello
I can get the printer to connect to the network, but my mac won't pick it up at the airport, and when I put the IP address of the printer in safari, that it does not connect.
I tried every index on the line for this problem and that would be very grateful for any help!
Thank you
Uninstall the HP software with option scrubber as follows:
Go to Applications/Hewlett Packard / click Uninstall HP
Click on continue
Highlight your device in the left pane
Hold down the Ctrl and Opt Cmd and click on uninstall
There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
Click on continue and let it finishNow run a software update.
Finally, download and install the software from here.
-
Re: Satellite L500D - cannot get the optical disc drive to work
Back again with this problem and this thread began again as it appears the original thread has been 'locked' ~ been awhile so it is aceptable.
I think that the TS-L633C TSST DVD/CD RW on my system is in fact die slowly, now I can not yet use Toshiba DVD PLAYER to watch DVDs. See http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=204206#204206 for the story.
Using the windows tool "FixIt" on a blank DVD got all green ticks OK but when I went to play DVDs ~ nothing!
How the reader '' hunt '' when I put any DVD in it and then fails, suggests that the reader was not not little by little and I must be looking for a new. Shame really, because I haven't used at all, hence the long time between my responses on this forum.
So OK, where from here.
Nearest service center is a 5 hour drive, and I will send this laptop for my financial and other stuff done busy resourses is more allow me to simply replace this system and start from scratch.
I'm ready to buy another drive, but cannot locate any online (new) and I am not aware if there are other brands / types which would be appropriate.
Toshiba Satellite L500D-PSLKOA-00U009 - TSST TS-L633C DVD/CD RW
Any ideas anyone?
To be honest, the situation is strange to me, and I think that you spent too long with all this.
In my opinion, you have to manage fast. The fist issue is: either defective or not ODD?
The reasons why it doesn't work with a Toshiba DVD player is not relevant at all. You can test it with VLC media player to see how it works.So I recommend you to follow:
You should not change your preinstalled operating system that you use for work or anything else. Try to get another HARD drive. Swap and install the OS by using recovery disc. Test the functionality of the WEIRD with the settings to be sure that the problem persists or not.In the end, if you are willing to trade the player s check Manual of use and you will be find the list of all compatible optical disc readers you can use with your model of laptop.
-
How to get HP PSC 2355 wireless connection work.
Wireless HP PSC 2355 does not connect. It worked initially when it is installed a few months ago. Have not used the printer for a few months. Now the wireless connection is not displayed.
How can I get the wireless to start working again? I use another network, then I used initially.
First, reset the printer:
You can restore the original settings to what they were when you bought your HP all-in-one device. Note to restore the default settings affect all changes made to analyze the settings and the country/region and language settings. You can perform this process from the control panel only.
1. press Setup.
2. press 3, then press again 3.
This displays the Tools menu and then select Restore Factory Defaults. The default settings are restored.
Then download the latest version of the software for your printer from the "Support & drivers" link at the top of this page. Run the software and choose 'Wireless' or 'network' when asked what type of installation you want. Make sure that the USB cable is NOT connected when you start the software.
-
Satellite P100 - cannot get the CD/DVD writer to work under WXP Pro
Hello
I recently updated my Satellite P100 - 188 (PSPA3E) to run Windows XP Pro SP2.
I can't have the CD/DVD writer to work well. I looked on the downloads page, but there seems to be nothing. It reads the CD/dvd, but allow me to write to them. If I put a blank CD in nothing happens.
Someone has ideas how to get this working again?
Thanks in advance...
Kind regards
Matt
Hi Matt
Maybe you should install like Nero burning software. Original Toshiba image (WXP MCE) it was an engraving Sonic RecordNow software pre-installed.
Maybe you are looking for
-
Multiple is plotted on the XY graph (by iteration)
Hi all I wrote a program that allows me to chart the theoretical data and change it in real-time to see how it changes the plots. Currently, I have all the equations in a for loop and have the berries each iteration XY are clusterted together and au
-
Windows Photo Gallery - cannot save the changes when you edit a photo
Photo Gallery - cannot save changes When you edit a photo, I get this message: "unable to save changes to this picture because library has encountered a problem." I tried various things I found online (several threads on this site as apparently other
-
Linksys BEFSX41 wired router - fixation using OpenDNS only
Question: I want to configure wired Linksys BEFSX41 router so that clients must use OpenDNS. I've already implemented the DNS1 and DNS2 with appropriate OpenDNS ip addresses. 208.67.222.222 and 208.67.220.220 Basically, the requirement must allow th
-
Remove a new machine of McAfee
While waiting for my new Dell Inspiron 7000, which, unfortunately, comes with McAfee AV. Been a loyal user of Norton for many years, so the first thing to do is uninstall McAtee and install Norton. Are there "traps" on the uninstall of McAfee, becau
-
How to lock the font size on my g-4 Pavilion Notebook 1229dx? (Windows 7)
The size of the font on my Pavilion 1229dx g - 4 changes constantly; It seems that changing the size occurs when I am sliding my finger on the touchpad. I currently use the toolbar to restore the size of the font to my favorite Setup (100%), but I do