TMS directory against LDAP directory

Similar Questions

• Check if the TMS directory is accessible from codec

  Hi all

  I'm starting a new configuration of telepresence. I have problems with directories. Seems that codec are not even trying to search the TMS directory.

  How can I check if the codec is configured to query the directory TMS?

  In "Advanced-> directory server 1 Configuration" ID has the default value, type MSD and URL to http:///tms/public/external/phonebook/phonebookservice.asmx

  When users press the directory key in remote control no shows, only my Contacts.

  Thank you

  Concerning

  Thanks for the update - the question is usually a proxy or a firewall - your endpoints need to have direct access to port 80 on the box of TMS on the subnet, they are on.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• TMS directory failed in the endpoints of series C after the migration of the device to the virtual computer

  Hi all

  We have migrated the 12.8 TMS from the device to the TMS 13.0 on the VM platform. There is no matching TMSPE and mainly used for management and directory service.

  Once the migration is complete on the platform of the VM, we found that endpoint C-series could not receive phonebook of TMS (while 95 MXP endpoints works very well with the TMS directory).

  The end point of series C, we check the Configuration-> directory server 1: URL. The link is converted from http:// /tms/public/external/phonebook/phonebookservice.asmx http:// tms/public/external/phonebook/phonebookservice.asmx.

  (In addition, we check the authorization of the two phone book page, and there is no IIS issue).

  In the 95 MXP endpoint, it can receive the telephone directory unit VM MSD and MSD.

  Best regards

  Ben

  Hi Ben,

  As confirmed by the curl command - you don't have access to the web page as an anonymous user.  You have to fix your permissions.  One of the fastest ways to do would be to try to reinstall the MSDS on the server again - this should reconfigure the IIS settings required for TMS.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Synch TMS directory phone book Local Codec

  Hi all

  I was wondering, is it possible to synchronize the TMS (server) directory to the Codec (C20, 40, 60) Local Directory?

  I checked on the guides of the admin and also on this forum, but without success.

  Thanks in advance

  See you soon
  Hugh

  Hi, unfortunately, this is not possible with the c series that it does not support the download directories. The MXP in comparison does not support this.

  / Magnus

  Sent by Cisco Support technique iPhone App

• TMS Directory link ISDN paired devices

  Hello world

  I currently have a problem trying to get a directory TMS containing details of ISDN on a SX20 with an ISDN connection.

  I created a manual list directory in TMS that contains details whether H323 or ISDN for various parameters.  The directory is detected by the SX20 and it shows all the details of H323, but none of the ISDN are listed.  The same directory, when it is applied to an edge 95, displays all the entries.

  I tried to create a directory containing only the ISDN numbers, and assigning that to the SX20 and then nothing is indicated.

  My first impressions are that that TMS has information as an 'ISDN' entry, and as SX20 has similar directory information stored in the form "H320", that the two are not compatible / correcftly - translation and so it's a TMS bug and/or TC software.

  In addition to the telephone directory, all the other functionality works as expected.

  Versions:

  TMS: 14.1.1

  SX20:TC7.0.1

  ISDN link: IL1.1.0

  Edit: I tried to push the same directory for a C60 and who was not either - TC6.3 - only the H323 entered were seen running - ISDN those lacking, is not purely a matter of SX20.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

  Hello

  There is no link to the SFT ISDN support. When 'route telephone directories' is set to Yes, TMS removes the entries she wants not the point endpoint to deal, that is what is happening here. TMS knowledge, SX20s cannot dial numbers H320.

  ? Kjetil

  Sent by Cisco Support technique iPhone App

• TMS directory system endpoints source folder

  Hello

  I came across a rather baffling problem with a few cases of TMS and I can't for the life in me know as to why this is happening.

  I get the following.

  in the option for creating source directory Cisco TMS, I create a new directory and link with the MSDS files and select the folder where all the end points, this creates the entries in the phone book for me as I expect with one exception, I will detail below.

  H.323 = [email protected] / * /

  H.323 = [email protected] / * /< this="" is="" where="" the="" issue="">

  IP = IP address

  I find that on some systems (this doesn't happen to all systems) in the second entry of H.323, the H.323 entry where I expect to see the directory (also known as E.164 number) number I see a URI where a field has been added at the end of the number, I'll give you a few examples below.

  DN = 1234

  set field = @video.net

  random field = @newdomain.com

  IP = 10.10.10.1

  I expect to see the following.

  H323 = [email protected] / * /

  H323 = 1234

  IP 10.10.10.1

  but I don't actually see

  H323 = [email protected] / * /

  H323 [email protected] / * /

  IP 10.10.10.1

  I have purged the TMS systems and added, I searched through the xconfig for the NouveauDomaine which is invalid and I can't find anything anywhere other than on the list of areas configured SIP VCS parameters in the second area, endpoints have disabled by default SIP and in both cases I expect to see that under a SIP entry not an H.323 entry

  This is the origin of the problem of when a user tries to call via the Directory site remote also responds to busy VCS is unable to find the appropriate directory number because the location request contains the domain as well as the DN.

  I worked around this by adding a transform to the VCS who sees the patter of specific numbering and the bands of the area, so the calls work, but I still need to understand as to what is causing this behavior.

  If I had to create the directory entries by importing information from the record of the VCS seem to be correct, its only when I try to import the entries of the endpoint via the system folder in TMS (or more exactly to import the information stored in the file on the endpoint system) I see the problem.

  a very popular Adviser.

  See you soon

  Dave

  Hello

  Picked up that the case with David and it seemed that at least on the systems the international denomination on the mxp MXP has been configured. The area of intellectual property also has a configured domain uri that has caused the other symptoms. We where able to erase the questions but still yet to see if the client is actually affected by the same configuration "mistakes".

  / Magnus

  Sent by Cisco Support technique iPhone App

• TMS directory - contacts AD

  I've recently upgraded to 14.1 and tmspe. During the upgrade, I've migrated my entries inherited TMS in the new solution highlights. The transmission of data contained in 5 groups with the users in each group. When I log in MOVI as legacy user and find the directory entries, everything works as expected.

  The problem I have is this - I created a new group and imported my Active Directory users. I can connect to MOVI as a user of Active Directory however when I try and search for users/end points in MOVI nothing appears.

  I checked for the provisioning directory ticks next to all my other access control entries in the phone book.

  All the world and ideas?

  Thank you

  Stem

  Hi Rod

  The first thing that comes to mind is the configuration information. If you have created a new group you also assigned to this group a provisioning model right? This model is different from other groups? Because other users directories work what is the difference between these users and the users AD?

  Users of AD have the configuration of the directory [email protected] / * /?

  / Magnus

• GSM numbers in the TMS directory

  Hello

  I have AD facility as a source of the telephone directory in TMS for video settings. I'm having a problem where the GSM numbers for users on endpoints TP are appearing as H320 and so the calls fail. I have a VCS/TMS connected to CUCM and want to route mobile calls to CUCM and then get out. Is this possible.

  Thank you!

  Then I was watching your definitions of zone again.

  • TMS needs to know that the endpoint can make H.323/SIP
  • The permissions for the system in the browser from should not be the call blocking options (settings down to change the planning parameters)
  • The endpoint must be associated with a zone of intellectual property with a defined gateway prefix
  • The area of intellectual property must be associated with a correctly configured ISDN zone
  • Route of the directories = yes

  If all this is in place, TMS will be able to deliver to an end point unique h323 call entered ISDN or telephone through the gateway prefixes defined in the area.

  If the entries are not displayed, TMS does not believe he can do a call from the bridge... the lack of supported protocols or failure of registration status.

  You can test this by creating a simple dummy directory with just the vocal entries in it.  Then associate this directory to your endpoint.  If it's an MXP, you can use the web interface of the endpoint to display the directory of the business directory provided by TMS.

  If you can not make it work again, I'd recommend appellant TAC where they can walk through your configuration with you.

• TMS directory

  Hey Cisco user community.

  I work with TMS 13.x and need to import a .csv file to add to my repertoire. It does not appear when I search the file.

  Is there some settings, the data must be in allowing TMS accept the file?

  The file contains a list of contact for Vidyo users data.

  Any help would be appreciated, and I am also happy to provide you with more information.

  Thank you

  Nick

  Network management may not be good community CSC to meet telepresence related research. You can republish or forward this question to the community MSDS here:

  https://supportforums.Cisco.com/community/5886/Telepresence

  I would like to get the attention of right from members of the community and experts.

  -Thank you

  Vinod

• Directory of TMS on the endpoints registered CUCM TC

  Since 14.4.0 TMS version, it is possible get endpoint CUCM registered directory server to point to the TMS directory instead of the CUCM directory.

  I tried to set up, but I still can't get it to work.

  On the endpoint of TC (version TC7.1.3), in Configuration > System Configuration > Server from the phonebook,

  I set the server type MSD and the URL as http://TMSserverFQDN/tms/public/external/phonebook/phonebookservice.asmx

  When I SSH to the endpoint TC I ping the TMS serverFQDN so DNS resolution on the endpoint is apparently works.

  When I open this URL in my browser, I get a page called "PhoneBookService" with GetPhonebooks links, ResolveSystem and research

  But on the preview endpoint it works everything simply. This shows just "no directory.

  How can I solve this problem?

  A few quick questions that jump to mind are:

  1. Endpoints defined in TMS?
  2. A TMS directory is published at the endpiont in MSDS?
  3. The directory TMS has a source valid and entered in it?

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate

• Import and export directory for CUCM and TMS

  How can I configure TMS and CUCM use of TMS directory for an endpoint registered to CUCM? I've added to TMS but and TMS can shoot CUCM Phonebook, but how does he see the directory for other infrastructure in TMS to fill in the directory of CUCM CUCM?

  tms_not_supported.PNG

  

  If the endpoint of telepresence is running TC7.0 or later, you can configure in CUCM using TMS as a source of spare phone book, there are also TMS 14.4.  Refer to the Administration of the TC on CUCM 10.5.1 endpoints (TC7.2) on page 24 for more information.

• Authentication against a LDAP repository and business intelligence

  I have many users who are authenticated against LDAP. I need to add a few users that may not exist in LDAP. I can create user in repository BI, and if the latter is in a group of the administrator, it is able to connect. But if this user is not an administrator group it get error "the successful execution of the intitializtion LDAP block is required. Y at - it anyway to authenticate LDAP repository agains users and BI?

  Vlada salvation,

  Have you tried to disable the "required for authentication" in the Init LDAP block?

  concerning

  John
  http://obiee101.blogspot.com/

• Questions of FindMe Provisioning/user between TMS &amp; VCS

  Hello

  I have what seems to be a problem in service between TMS and VCS.

  Using TMS to import users from AD (from 2 domains of x), everything seems to work, and can see the users in the provisioning of TMS directory. MOVI users use AD authentication which connect properly.

  User login also works very well on the VCS (with connection LDAP AD). However when to call the findme users address VCS does not recognize the configured users? If you navigate in user accounts, the user is not displayed, if you run a search on VCS (users account address name or findme) findme VCS find the user. Once the user has been found and open if you click on save button (without changing details), the user will then appear in the VCS user accounts section and findme works correctly.

  We use the TMS 13.1.1 and VCS x7.0.2 (Cluster).

  I would like to know if you have solved your problems or you are still having problems? Any suggestions for help would be appreciated.

  Thank you

  Matt

  Hi Matthew.

  Findme users must fill in the "user accounts".

  But you must make sure that the VCS 'Cluster name' matches the 'SIP server address' in TMS.

  TMS:

  VCS:

  I hope this helps.

  / Magnus

• Mixed (LDAP + APEX accounts) authentication in Apex 4.2.3

  Hi all

  I've built and the application in version 4.2.3 against 11g R2 in Windows 2008 Server. Current authentication is HTML DB (authentication of the Apex). My customer wants to be able to authenticate users based on their Active Directory connections. Is it possible to have a mixed authentication method in this version of the Apex? Could you guide me to some documents, samples, etc.?

  Thank you

  Sinan

  Hey, Sinan.

  It turns out that I recently needed to implement these features even.  I created an application (version 4.2.1 on Oracle 11 g 3 and mod_plsql) Apex in which some users authenticate LDAP Windows while other users authenticate on a table of database containing usernames and encrypted passwords.  I created a package called app_security_pkg which is called from a PLSQL PLSQL submit after region on the login page (page 101) of my application.  This package, distinguishes a type of user of the connection on the other in turn, according to certain criteria.  In my case, the login page was a drop down in which users will have to choose the "user type" they connect as long as.  Then, if a user intends using my application, say, they would be an 'administrator', so select the option 'Administrator' in the menu drop-down.  If a user is using the application as an "experimenter", he would choose the "Experimenter" in the menu drop-down option down.

  They then have to type their user name and password on the login page, click on the 'Login' button and my package code.  The selected user type is sent with the entry of username and password.  According to the selected user type will determine what authentication scheme is used to verify the credentials passed in connection.  In my example, if the type of user 'Administrator' is adopted, the LDAP protocol is used; Otherwise, the connection user name and password are checked against the database table (the transmitted password is checked against passwords in encrypted stored in the table).

  If the type of the selected user is 'Administrator' and credentials have been verified with success against LDAP, the user is presented with a certain 'landing page' in the application.  If the selected user type is 'Experimenter' and the connection credentials have been verified successfully against the database table, then the user is presented with an another 'landing page' in the application.

  In a nutshell, this is how my multiple authentication scheme works.  And I would add, it works very well.

  I would like to include a link to my application but you would not be able to check it out since, obviously, you're not in our LDAP directory.

  I hope that helps you.

  Elijah

• LDAP - free unused connections

  Hello
  
  
  I am very new to work with Active Directory. I have a PL/SQL script of net to connect with LDAP and it works fine.
  
  My task is to check the user against LDAP protocol names.
  
  But'm ' DBMS_LDAP: cannot open more than 63 LDAP connections "error.
  
  I went through so many sites for this problem. Everyone is suggesting to close the connection after the execution of the script.
  
  I already have a closing speech in my script.
  
  "l_retval: = DBMS_LDAP.unbind_s (l_session)"; "."
  
  
  Please help me solve this problem.
  
  
  Thank you
  Lucas

  If you want as your return value of prior to the separation, and then return your without commitment value of function in a different variable calls.
  You must Unbind before your RETURN because statement that the RETURN is when the function ends and no statement, after that it will be executed.