TouchSmart HP ENVY 15-j151sr: do not load Windows

Similar Questions

• Satellite L300 laptop will not load Windows

  I have a model of Satellite L300 number PSLB0A - 00L 022 running windows Vista.

  The problem is that it does not load Windows. It starts ok and I can access the boot manager and the Setup utility and that's it. It stops just loading.
  After studying the problem, I ran a car aptitude test and the result was the error code 0 x 70. After looking at the code I m under the impression that I need to erase the disc. I have no problem with that.

  My question is - if I run the windows Recovery Wizard will be it solve my problem? I will have to re install vista at all? All advice is appreciated!

  Hello Jane and welcome in the Toshiba forum

  After reading your ad, I must say that the best solution and easier for you is to reinstall the operating system via original Toshiba recovery DVD. This DVD contains the operating system, all necessary drivers, specific Toshiba and utility tools. After recovery image installation you will get state out-of-box and clean the preinstalled operating system.

  Yes, this should solve your problem. Please note: when you do it all saved data will be deleted.

  You have some important data saved on your laptop?
  Do not use this disc reinstall Vista and everything should be ok again.

• Re: Satellite L670D does not load windows

  Hi, I have a toshiba L670D, who recently had a windows update and since then, every time I try to turn it on will not load windows, but just comes up with the error "error fatal c0000034 application update operation 207 0f 102311 (_00000...)"

  Is there anyway I can fix it myself or is it a case of calling an expert or even go shopping for a new?

  Try to start Windows in safe mode and try to roll back OS to an earlier time using System Restore tool.

  Please post comments.

• Lenovo battery Z50 - 70 does not load Windows 8% 10

  Hi lenovo Z50-70 battery does not load Windows 8% 10

  I uninstalled the old Yang APP and reinstalled this

  were of no irrelevance that even once and adde the application in the windows store "parameters of Lenovo.

  And it does not load beond 8%

  A have you tried a new charger did not help

  text is pretty funny to 8% and 2 min at full load :-)

  Try opening the energy manager and click on settings, click on conservation mode to turn it off, then unplug the power cord and plug it back again and you should see the battery load again.

• After recommending the bios update, hp dv6131od running xp pro sp3 will not load windows - is there a wa

  After installing an update of the bios recommended on the hp website my dv6131od running xp pro sp3 will not load windows

  Update does not seem to have problems - failure, lack of time for flash, backup, etc.

  boot sequence seems normal (finds it a bootable cd in the drive, etc.), but windows won't load in safe or other mode

  next steps?  is there a way to access the BIOS?

  Thank you

  There is a simple solution to this problem.  The HP Online Crash Analysis Team has finally responded to my email after 34 days.  I had given up hearing from them despite several requests to repeat.

  I had completely disassembled the laptop trying to find the bios setting the jumpers on the motherboard in response to an idea contained in one of the PM, I sent... all to nothing does not...

  OCAT told me to look in the BIOS under "system configuration" for the Native SATA support.  The last update of the BIOS resets this point 'activated', but that only works for Vista & Win 7.  This must be set to "disabled" for XP and previous operating system.

  I hope that this post will save someone having to wait 5 weeks invest hours of work for a solution that took 3 minutes!

• I get a message that my system will not load Windows 8 Preview Release. Why?

  My computer is a Dell... It has 2.40 Ghz processor and 1 Gig of Ram... But it tells me my computer will not load Windows 8... Why?

  Can anyone explain that?

  Yes, your CPU or the motherboard doesn't have the ability to run hardware D.E.P., so there is no chance of running the Preview Release of 8-all somehow.

  There is the possibility to set the nx or xd bit in the bios and the cpu to support it as well.

  TBC: Run CPU - Z and say please use the exact model (details) of the processor, it says you have.

• Computer does not load Windows after reset after installing HP-J6413

  Bought J6413 all-in-one; the software that is installed according to the instructions on the CD.  Attempted to restart after the installation, the computer hangs upward after shooting intself on and display the logo of the motherboard, does not load Windows.

  Printer is off, did reset, everything was fine, Windows loaded etc.  Repeat the action and came to the conclusion that the power of the computer with the printer off left (it's a fax machine, it should be all the time) or even reset the onboard computer after, say, install new software, prevents the loading of Windows on them turn on the computer.

  Only possible mode of operation is to put off the printer, then turn off the computer, then turn on printer to serve fax standby and then do the same set of operations before turning to new computer.

  Please refer to the manuals that you received for your PC and disable the "USB Émulation" and "USB devices starting" the BIOS settings.

• New Pavilion g7-2220 will not load Windows to start-up

  Hello

  I just bought a new Pavilion g7-2220 and am just finishing the initial commissioning.  All registration modules and guests of live recording of MS are fine, but then the computer will not load Windows.  He explains in brief it is impossible to load Windows from the hard drive in a small dialogue window, then restarts and brings back me guests for the first time again.  It is supposed to be preloaded with Windows 8.

  Any help would be appreciated.  Again, this computer is brand new.

  Thank you.

  Hey Shannon3363,

  I'm very sorry to hear that you are having problems of this kind out of the box. The first option, I'd watch is an Exchange. If this is not a viable option, you can reset the operating system. This is a very simple process.

  1. prior to turn on/off the laptop, press in and hold the escape key

  2. press the power button as usual to start and hold down ESC until you see the Menu Start Up

  3. on the Start Menu, press F11 to go in Recovery Manager

  4. choose your keyboard

  5. click on troubleshoot

  6. click on reset your PC

  7. select just delete my files

  Leave about 30-45 minutes for the reset is complete. If you're still having problems with this load Windows normally, please let me know. Once again I aplogize for the inconvenience. Depending on where you have, there could be several reasons so that he can behave in this way. If you've got it to a brick and mortar store, technicians will provide implementation services and anything can happen during this period. I'll keep an eye out for your answer!

• Envy 15-j051: my HP Envy 15-j051 does not load when the computer is on, but will charge when turned off

  whenever I'm on and trendy get plugges but do not load, but when I stopped and keep power connected it charges the battery. I checkd the battery and it says primary school-OK (1) tell systems check all past

  @lagrit1023 ,

  Hello and thanks for the display on the HP support forums.  What you have going on here, it's a problem with the regulation of power on the motherboard or a problem with not enough amps from the power supply.

  Can you try feeding on a laptop or have a place that you can take to check?

  The only other way to check if you have already made the checks of the battery and so on is getting the system sent repair.  To do this, you will need to contact the HP support by phone.

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Please let me know how things are going.

  Thanks again for posting and have a great day.

• Help, please! computer HP laptop g72 does not load windows

  I can't get my laptop to initialize. I was it clean and running virus/spyware scans when it overheated and judgment (something he seems to do more in more often lately), I came back to the room to check on it and he stopped. He gave me the usual message about how he had disappeared in hibernation because the internal temperature exceeded blah blah blah (don't remember exactly what he said, but it wasn't the basics of it) now normally at this stage it will restart and be well and I can continue with what I was doing before. However this time it will not go beyond the second screen. It's what he does... (I will include the information in the end system)

  I press the power button then screen shows the following

  1 HP screen of the logo with the message "Press ESC for Boot Menu" at the bottom left then flashes to the next screen.

  2. starting Acronis Loader...
  Press F11 for Acronis Startup Recovery Manager... (horizontal cursor flashing after...) then flashes to view the first screen again

  and this process is repeated again and again until I got disabling or press ESC to #1 screen or F11 to the screen #2 how it will load either the menu start screen where I can access info sys diagnotics, BIOS or system recovery system.  or Acronis where I can make backup dics or start the Recovery Manager (who I'm trying to deal with the system if that is possible at this time because there are pictures and things on the hard drive that I want not deleted if it can be avoided)

  the process is normal to start but after #2 it should be blank with blinking cursor and then begin loading windows... I cannot at this point. He repeates just the first two times, I let it run for about 10 minutes at a time to see if she would do anything else, and it won't.

  System info-

  portable mode: HP G72 notebook PC (not sure what particular model because I don't know where to find this info)

  System ID: 1425

  Product number: LE846UA #ABA

  Warranty start date: 27/03/2013

  BIOS date: 08/11/2010

  BIOS version: F.26

  Processor type: Intel Pentium CPU [email protected]

  Processor speed: 1866 MHz

  Operating system: Windows 7 premium 64-bit

  I bought this computer used. The battery has never held a charge, I've always had it up to use it, but I don't know if I had to buy a new battery it would probably work. I never had the money to make and never really needed it so never bought.

  I tried to access the BIOS and it requires system administrator password. I tried to enter my password that I used to connect to windows, but that did not work. After 3 tries I have a message to disable the system with [6207076] below.

  Is there someone who can help me to fix it?

  I really don't want System recover unless there is a way to access the LIBRARY (documents, music, pictures) if I can help it. I don't have the ability to transfer all of my photos from my other computer before that happened.

  Please help me!

  Hello

  The code below should allow you access the bios menu:

  76165078

  Once, I would like to delete the password entirely - use the arrow keys to select the Security tab and press ENTER.  Use the arrow keys again to select the admin password option and press ENTER.  Enter the current password (use the above code), and then for the new password, just leave this blank and press on enter – do the same for the confirmation field.  Press f10, select this option to save the new settings and press to enter.

  Once completed, boot into the bios menu and reset the default settings - it may also be useful running a quick diagnostic on the HARD disk and the memory that is to be found under the Advanced or the diagnosis tab.

  Kind regards

  DP - K

• computer does not load windows xp

  computer will not load in windows sometimes happens at startup repair but still does not work
  Pentium 4

  judged fault dust stop start thank you for your suggestions

• Computer does not load Windows. (Missing\corrupt file and the disk read error)

  I woke up this morning and my computer screen said:

  "Read a disk error has occurred."
  Press Ctrl + Alt + Delete to restart»

  So I did, and he just keeps it again and again. I turned off my PC, disconnected from the power and took out the battery. EXPECTED, put everything back in and turned on the computer. This time he made a lot of strange beeping noises and took forever and then I got this error:

  "Windows was not start because the following file is missing or damaged:
  \SYSTEM32\NTOSKRNL.exe
  Please reinstall a copy of the above file.

  I pressed on enter and it gave me the error reading disc again.

  Yesterday I updated my BIOS. So I also tried to go to my BIOS screen and "Load factory default settings", but I always get errors that I said just above and windows does not load.

  Help =)

  Hello I would wait until you try to do the repair first

  Make sure that the hd is just a notebook size hd
  Make sure that the speed is the same thing that you already size is really for you
  before you start to have a complete set of installation discs for the mfgr
  If you only use the os disk you will not load the microsoft embedded key encode any additional programs the mfgr installed or modified specially for your computer model and the party in the form of hard disk, you will need to do it yourself the format should be identical to the new factory
  uninstall all the equipment installed after you bought the computer (you must add once installation is complete)

• Samsung laptop computer does not load windows 7, need to reinstall (no cd, no cd key)

  Samsung laptop comes with windows 7, does not load past the bottom (and even in this case, does not load the user/pw. Need to reinstall how? It did not come with a cd key and I tried to go back to the last good config and it did not work (im going with a file corrupt and need a cd key). He gets in the background, but is not past. I want to just reinstall windows 7 home 64 bit, but I miss a cd and don't know how to get the cd or the cd key for it.

  New computers coming often pre-installed with Windows 7 have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.

  This is how the recovery partition is accessible to most popular brands...

  For Samsung, press F4 to the power upward...

  You will probably find the product key in the compartment to batteries.

  COA certificate of authenticity:

  http://www.Microsoft.com/howtotell/content.aspx?PG=COA

  What is the certificate of authenticity for Windows?

  http://Windows.Microsoft.com/en-us/Windows7/what-is-the-Windows-certificate-of-authenticity

• TouchSmart HP ENVY 15-j009wm: TouchSmart HP ENVY 15-j009wm does not read USB Flash Drive after Downgrade to Windows 7

  I've demoted installed Windows 7 with Flash Drive but I need help. Windows 7 doesn't read my Flash drive more? He can read my USB keyboard but does not read a USB Flash drive.

  I have no Internet on the computer, so that means I can not update my drivers. And I have a few drivers in my flash drive I want to install, but I can't.

  I read this: http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/HP-ENVY-TouchSmart-15-j040us/td...

  It not me any more because I can't access my USB drivers

  Hello:

  Looking at your other posts it seems that you have yourself painted in a corner.

  Since there is no inheritance or the setting USB auto in the BIOS, your only option would be to remove the hard drive, then put it in a USB drive enclosure sata hard laptop, plug in another PC so it can be read, download the drivers there, you need and copy to you user profile on the hard drive removed.

  Chapter 5 maintenance manual provides the procedures of withdrawal and replacement for the hard drive.

  http://h10032.www1.HP.com/CTG/manual/c03733656

  Reinstall the hard drive, run the drivers, and you should be good to go.

  These would be the drivers you need for your model...

  SM bus controller: install this first and reboot.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=cp_127691_1

  USB3: Install these two and restart.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=6943835&swItemId=ob_139250_1&swEnvOid=4058

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=6943835&swItemId=ob_133037_1&swEnvOid=4058

• HP dv6 envy: my laptop turns on but it does not load windows

  Hi, recently my computer has stopped working. It lights up; However, he will just stay at the startup screen until the screen will Dim. I ran the hard drive DST short test and it comes back as being down. My FAILURE ID is 0LGDAJ-6MP82Q-QFPK1A-60TX03 and my PRODUCT ID is C2M16UA #ABA. Can anyone advise me on what I should do? Also can save my files to that hard drive?

  Thank you!

  Hello
  
  Data sheet: http://support.hp.com/us-en/document/c03497843
  
  Manual: http://h10032.www1.hp.com/ctg/Manual/c03591281
  
  Please replace the HARD drive failed by a new similar form factor.
  
  Order the HP USB recovery, if you have not created a game for yourself after you set up the laptop.
  Or buy it here:
  http://www.computersurgeons.com/p-23043-Windows-8-64-bit-Supp-1-Recovery-Kit-708588-001-for-HP-envy-notebook-PC-model-number-DV6-7245us.aspx
  
  You can remove the HDD, connect to another PC using SATA USB adapter. Use Windows Explorer and copy the files you need to HARD drive failed.
  
  Concerning
  
  Visruth