Try to get a USB capture card to work

Similar Questions

• Try to get a new graphics card to work...

  I have a GeForce GT of 640 that I try to install in my office p7-1414.  Problem is it seems to have some sort of conflict with the integrated graphics card, as when it is installed in the slot of PCIx16, NONE of the screens will be exploited.

  It doesn't seem to be a way to disable the onboard graphics via the BIOS (AMI Bios 8.04), and I know that the card works as it still works with the office, that I recently tried to replace.

  Any help on this would be greatly appreciated.

  Here are the specifications of your desktop HP Pavilion p7-1414. According to specifications, your system comes from the factory with a 300 Watt power supply. Review the specifications for graphics cards of TG 640 indicates they generally recommend a minimum of 350 watts system power supply. Although this is not the only problem, it's a start. There is no option in the BIOS to disable the onboard graphics on board, as this is done automatically when a PCIe x 16 card into the PCIe x 16 slot.

• Try to get a USB cable to installed on Windows 7 (64 bit) series.

  I try to get a USB cable to installed on Windows 7 (64 bit) series. Radio Shack model: 26-949. The cable works fine in XP. I tried Radio Shack, FTDI drivers prolific, but to no avail. When I try to load the drivers, it does not recognize the device. When I plug in the device, instead of motorhomes up as a COM port, it appears as "another device-USB-Serial Controller." I completely restored Windows (re-formatted hard drive, reinstalled Windows), but none of the drivers I found works with Windows 7 (64-bit).

  Hi BUBBA211,

  Thank you for using Microsoft Windows forum.

  Check if your USB device is compatible in the Windows 7 Compatibility Center : http://www.microsoft.com/windows/compatibility/windows-7/en-us/default.aspx

  Doesn't seem to be compatible with Windows 7 64-bit edition.

  Contact the manufacturer because they are the best people to answer your question.

  In the meantime, run your USB device compatibility mode.

  Follow the steps from the link to the older in this version of Windows programs : http://windows.microsoft.com/en-us/windows-vista/Make-older-programs-run-in-this-version-of-Windows
  Hope this has helped
  Aziz Nadeem - Microsoft Support

• How can I get my USB printer doesn't work?

  I am trying to install a Dell 3000cn laser printer in my computer. He started by putting a virtual printer in my control panel that would not print it had nothing on the Hardware tab, under its properties and real hardware was still on the list of unknown devices in the bottom.  I removed both and removed the driver and tried to install the printer before I plugged it in which does the same thing as before so I went into the Device Manager and there was no printer listed. I've uninstalled the usb printer support and removed everything that are associated and tried. Now I get support of usb error has a printer driver problem.

  I tried to support the customer of Dell they got hung up, I tried Windows customer, they want me to pay.
  I've exhausted the research online and can't find 5 people with the same question online all back in 2008 to 2010 which was never resolved.

  How can I get the USB printer to work?

  Generally, printers do not appear in Device Manager.  You will see, however, registrations for "IEEE 1284.4 devices ' or ' IEEE 1284.4 compatible printer" in particular for HP printers.  It is possible that your Dell printer is really a re-badged HP.

  What exactly did you delete when you have uninstalled the "usb printer support '?

  Please provide the full error message text that you do when this error.

  Why do you think you had a 'virtual' printer is installed?

  Click Start, click devices and printers.  What are the items in the category 'printers and faxes '?

  Did you download the driver appropriate for your version of Windows (including 32-bit or 64 - bit) from here--> http://www.dell.com/support/home/us/en/04/product-support/product/dell-3000cn/drivers?

  Did you follow these installation instructions:

  Download

  1. click on the link download now to download the file.
  2. when the file download window appears, click Save to save the file to your hard drive.

  Extract the files
  1. navigate to the location where you downloaded the file, and then double-click the file to decompress the download package
  2. click on continue.
  3 specify the location where to unzip the files.
  4. click on the OK button to extract the files.
  Once the file extracts the message all files have been unzipped will appear.
  5. click on the OK button to exit the installation program.
  6. go to the Start button.
  7. go to settings, click Printers.
  8. Select Add a printer.
  9. follow the instructions to set up your printer.
  10. Select Have disk and point to the location where the drivers were extracted.

  Install the printer driver:

  1. install the printer driver using Add Printer method.
  2 follow the instructions that appear in the Add Printer Wizard dialog box to install the printer driver on your computer.

• How to get the dual graphics card to work together?

  I have a satellite L series with dual graphics card that works together. Its an AMD Radeon 3400 m apu with a built-in HD 6520 G and a discreet graphics of 6400 m.

  The 6400 m turns on never, I used the amd system monitor to see if it is already in use, but it's never.
  Even if the 6520g is at full load it lights.

  Any suggestions would be helpful.
  Thank you.

  Hello

  As far as I know, this topic has already been discussed here in the forum and the switch between internal and external ATI GPU is not supported.
  Just designed by nVidia Optimus technology is supported
  So you can switch between the GPU from Intel and nVidia (if both would support Optimus technology)

• How to get 2 usb ports 3 to work on 2215dx hp with windows 7

  I just updated my hard drive on the laptop HP 2215dx with a Samsung ssd. I did a clean install of Windows 7 instead of win 8. The only thing that the doesn't work after installing all the disks that I found is the 2 usb ports 3. They produce an error in Device Manager. What driver to install to get these 2 usb ports work under Windows 7?

  Thanks for the help.

  Hello

  What is a G7-2215dx? Please try:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us&LC=en&softwareitem=ob-102571-1

  Kind regards.

• Try to get a sample of authentication applet works.

  package GenSignVerify;

  Javacard.framework import. *;

  Javacard.security import. *;

  /**

  */

  SerializableAttribute public class GenSignVerify extends Applet {}

  /**

  * Only installation method of this class should create the object of the cmdlet.

  */

  public GenSignVerify() {}

  Register();

  }

  /**

  * Install this applet.

  *

  @param Baker

  * the table that contains the installation settings

  @param bOffset

  * starting in Baker offset

  @param bLength

  lengthwise in bytes of the data parameter Baker

  */

  {} Public Shared Sub install (byte [] Baker, short bOffset, bLength bytes)

  GP-compatible recording of JavaCard applet

  new GenSignVerify();

  }

  /**

  * Treats an incoming APDU.

  *

  * @see APDU

  @param apdu

  Incoming APDU

  * @exception ISOException

  * with the bytes of response according to ISO 7816-4

  */

  {} public void process (APDU apdu)

  Byte [] buf = apdu.getBuffer ();

  Byte [] testSig = new byte [256];

  Byte [] test = new byte [] {0x01, 0x02, 0x03, 0x04};

  Key of the key pair = null;

  SIG Signature;

  /*

  check the command SELECT UDPA

  If ((buf [ISO7816. OFFSET_CLA] == 0) & &

  (buf [ISO7816. OFFSET_INS] = (byte) (0xA4))) {}

  return;

  }*/

  If (selectingApplet ())

  {

  return;

  }

  apdu.setIncomingAndReceive ();

  switch (buf [ISO7816. {} OFFSET_INS])

  case (byte) 0 x 01:

  if(Keys == null)

  {

  keys = new pair of keys (KeyPair.ALG_RSA_CRT, KeyBuilder.LENGTH_AES_256);

  keys.genKeyPair ();

  }

  INITIALIZE THE SIGNATURE AND SIGN

  GIS = Signature.getInstance (Signature.ALG_RSA_SHA_PKCS1, false);

  SIG.init (Keys.getPrivate (), Signature.MODE_SIGN);

  short Len = sig.sign (test, (short) 0, (short) test.length, testSig, 0 (short));

  VERIFY THE SIGNATURE

  SIG.init (Keys.getPublic (), signature. MODE_VERIFY);

  GIS. Verify (testing, (short) 0, (short) test.length, testSig, (byte) 0, len);

  apdu.setOutgoing ();

  apdu.setOutgoingLength (len);

  apdu.sendBytesLong (testSig, (short) 0, len);

  break;

  0xCA, case (byte):

  break;

  by default:

  good practice: If you don't know the statement, say:

  ISOException.throwIt (ISO7816.SW_INS_NOT_SUPPORTED);

  }

  }

  }

  and this is the .scr file

  Test script for the Applet "GenSignVerify".

  power-up;

  Select GenSignVerify //aid/19550633C5/99

  0 x 00 0xa4 0x04 0x00 X 06 X 19 0 0 0 X 0 X 06 55 0 X 33 0XC5 0X9A 0x7F;

  Send the APDU with chain J C 3

  0 x 80 0xCA 0x00 0x00 0 x 03 0x4A 0x43 0 x 33 0x7F;

  Must return SW1:6 D, SW2:00-> statement not supported since INS = D2

  0 x 80 0xD2 0x00 0x00 0 x 03 0x4B 0x4D 0 x 33 0x7F;

  To enter the key of the case and gen, sign and verify data

  0x00 0x01 0x00 0x00 0 x 00 0x7F;

  powerdown;

  When I build and run this is my output:

  Received ATR = 0x3b 0xf0 0x11 0 x 00-0xff 0x00

  CLA: 00, INS: a4, P1: 04, P2: Lc, 00:06, 19, 55, 06, 33, c5, 9A, the: 00, SW1: 90, SW2: 00

  CLA: 80, INS: ca, P1: 00, P2: Lc, 00:03, 4, 43, 33, the: 00, SW1: 90, SW2: 00

  CLA: 80, INS: d2, P1: 00, P2: Lc, 00:03, 4B, 4 d, the 33,: 00, SW1: 6 d, SW2: 00

  CLA: 80, INS: P1 01: 00, P2: LK, 00:01:45, the: 00, SW1: 6f, SW2: 00

  run:

  BUILD successful (total time: 6 seconds)

  The last line is where is my mistake. 6F00 indicates that there is no specific diagnosis. I don't know where I went wrong in my code. Any help or advice would be appreciated. Thank you!

  According to this - https://forums.oracle.com/message/10589893 , you should use KeyBuilder.LENGTH_RSA_512 when you use a Java Card sim card. So now the correct code is:

  package GenSignVerify;

  Javacard.framework import. *;

  Javacard.security import. *;

  /**

  *

  Raja * @author

  */

  SerializableAttribute public class GenSignVerify extends Applet {}

  private key pair key = null;

  SIG Signature private;

  Byte [] testSig = new byte [256];

  Byte [] test = {0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f};

  Check Byte [] = {0x00};

  public GenSignVerify() {}

  CREATE THE SIGNATURE OBJECT

  GIS = Signature.getInstance (Signature.ALG_RSA_SHA_PKCS1, false);

  }

  {} Public Shared Sub install (byte [] Baker, short bOffset, bLength bytes)

  GP-compatible recording of JavaCard applet

  new GenSignVerify () .register (Baker, (short) (bOffset + 1), Baker [bOffset]);

  }

  {} public void process (APDU apdu)

  value Boolean = false;

  GOOD PRACTICE: BACK 9000 ON SELECT

  If (selectingApplet()) {}

  return;

  }

  Byte [] buf = apdu.getBuffer ();

  switch (buf [ISO7816. {} OFFSET_INS])

  case (byte) 0 x 01:

  If (key == null) {}

  try {}

  CREATE THE RSA KEY PAIR

  keys = new pair of keys (KeyPair.ALG_RSA, KeyBuilder.LENGTH_RSA_512);

  }

  {} catch (EC CryptoException)

  short-reason = ce.getReason ();

  }

  START THE PROCESS OF GENERATION OF CARD KEYS

  keys.genKeyPair ();

  }

  INITIALIZE WITH THE PRIVATE KEY

  SIG.init (Keys.getPrivate (), Signature.MODE_SIGN);

  BUFFER INCOMING SIGN

  short Len = sig.sign (test, (short) 0, (short) test.length, testSig, 0 (short));

  INIT WITH PUBLIC KEY

  SIG.init (Keys.getPublic (), Signature.MODE_VERIFY);

  VERIFY THE SIGNATURE

  value = sig.verify (test, (short) 0, (short) test.length, testSig, (byte) 0, len);

  IF AUDITED CORRECTLY, RETURNS 1, OTHERWISE RETURN 0

  If {(value)

  Check [0] = (byte) 0 x 01;

  }

  apdu.setOutgoing ();

  apdu.setOutgoingLength ((short) verify.length);

  apdu.sendBytesLong (check, (short) 0, (short) verify.length);

  break;

  0xCA, case (byte):

  break;

  by default:

  good practice: If you don't know the statement, say:

  ISOException.throwIt (ISO7816.SW_INS_NOT_SUPPORTED);

  }

  }

  }

  With the same script APDU, I get the following result:

  Received ATR = 0x3b 0xf0 0x11 0 x 00-0xff 0x00

  CLA: 00, INS: a4, P1: 04, P2: Lc, 00:06, 19, 55, 06, 33, c5, d0, the: 00, SW1: 90, SW2: 00

  CLA: 80, INS: ca, P1: 00, P2: Lc, 00:03, 4, 43, 33, the: 00, SW1: 90, SW2: 00

  CLA: 80, INS: d2, P1: 00, P2: Lc, 00:03, 4B, 4 d, the 33,: 00, SW1: 6 d, SW2: 00

  CLA: 00, INS: P1 01: 00, P2: Lc, 00:00, the: 01, 01, SW1: 90, SW2: 00

  Hope that helps someone who is stuck...

• Try to get the HD-DVD player to work on the Satellite P100-463

  Hello world.
  I bought this baby the weekend and since I am struggeling trying to get HD-DVDs to work on it. I added the HD_DVD xbox 360 drive, but Power DVD Software Advisor continues to say that the graphic card 9Geforce Go 7900) drivers must be updated to read HD-DVD content. Now, there is no available such as newer driver installed (84.0?)

  Can someone please advise if the card supports protection hdcp anyway? Maybe my problem is another source.
  Thanks for the tips.

  Wait do you use player designed for the Xbox in the Satellite P100?
  Hmm, I m surprised that this device is compatible with the Toshiba laptop.
  Anyway, as far as I know you need a special DVD player to play and watch HD-DVD on the laptop.
  A simple WinDVD does not support the new HD-DVD.

  By the way: I know a Toshiba model that shipped with the HD_DVD drive.
  It was a Qosmio G30 DVD HD model.
  I found a new Nvidia GeForce Go7600 8.3.2.7 Version graphics card driver update in the download section of driver on the Toshiba site
  But I put t know if it s compatible with your card...

• How can I get Tun Miniport, Microsoft card to work properly.

  There is an exclamation on it in Device Manager, but windows declare that it does not work correctly

  I'm on hp Pavilion dv6000

  Hello

  ·         You are able to go online?

  ·         You receive all code or an error message when you try to connect to the Internet?

  Method 1:

  I suggest you to reset the TCP/IP stack and check if it helps solve the issue.

  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

  http://support.Microsoft.com/kb/299357

  Method 2: Turn off IPv6

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.

  NOTE:

  You should do this for each network connection.

  Method 3: Disable the DHCP Broadcast Flag

  Follow the link below to disable the DHCP broadcast flag

  http://support.Microsoft.com/default.aspx/KB/928233

  Important:

  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  How to back up and restore the registry in Windows

  You can also try the following items on the advice on common network problems.

  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  http://windowshelp.Microsoft.com/Windows/en-us/help/fc58605e-A2be-470C-95b3-6808a76347991033.mspx

  Hope the information will help. Please go back and let us know.

• Try to get the Photoshop 8.0 disc working in another PC, after the failure of the motherboard...

  I need help - my motherboard failed in PCno1 and I removed the hard drive and inserted in another PC and have it running with the old drive as a second drive - and it is this second disc which contains the Photoshop.

  I can't find the disks to reinstall photoshop so need to know how to get this working.

  When I try to open photoshop, I see the boot logo, but the I get an error message saying "cannot take place because of missing or incomplete data" which I guess is linked to the license?

  If anyone can help?

  My wife has this urgent need for a presentation of the competition!

  Thank you very much

  Murray

  I found the answer myself finally that CS2 is the equivalent of PS8.0 and is now available for free download on the adobe site.

  I lost a day whole, but grateful to have found the solution...

• Impossible to get the USB flash drive to work

  I have a new Satellite L500 with Windows 7 and it will not recognize/install the USB flash drives. A msg comes up saying "software device driver has been properly installed. I tried several flash drives - they are OK & work on other machines - including an another Toshiba running Windows 7.

  Other devices work in the USB ports, so the ports are OK.
  Windows cannot resolve the problem, I have checked all USB drivers are updated in Device Manager & made a system of analysis of file without success.
  The Bank recommended a reload & restore factory default - other options?

  Have you installed driver chipset?
  Your laptop comes with Vista or Win7?

  You have just upgraded to Vista or Win7 clean setting?

• try to get the HP SCANJET 5100C to WORK WITH WINDOWS 7. _ No. DRIVER UPDATE OF HEWLERD PACKARD

  I HAVE WINDOWS 7 AND AM LOOKING FOR A DRIVER, OR WORK AROUND FOR HP SCANJET 5100C SCANNER.

  NO DRIVER TO DATE OF H.P.

  The HP page says that XP drivers. Then you can try to use XP Mode, if you use Windows 7 teacher or company or buy a Windows 7 compatible scanner. "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Try to get a wireless remote control to work with Flash presentation... Help!

  I know almost nothing about Flash or Powerpoint.  They gave me a Flash presentation that I need I want to show at meetings using my wireless remote control, but I can't seem to move forward and backward between slides (works very well using the arrow keys on the keyboard to laptop - Windows XP Pro).  The remote works fine with Powerpoint presentations, so I don't know the remote is ok.  Is there some setting/order I have to run my Flash presentation with my remote, or do I need a special remote control?  I have already spoken to the remote support (Keyspan/TrippLite) and they were totally unknown wirh Flash and said simply that their device works with Powerpoint, as announced, which was true, but they could not help me with Flash presentations.  There, can someone help me?  Thank you very much!

  Thanks a lot for all the help.  I see a lot of situations where I can use the functions available through the use of SharpKeys2 key mapping, as well as a few other programs I 'discovered' during my travels recent (KeyTweak + AutoHotKey).  Even better for my situation here, I just got a more advanced model Keyspan remote (PR-Pro3) what Flash handles submissions very well - I have no idea why - and nor their tech support, apparently.  Anyway, the PR - EZ1 will come back to Newegg and I'm fortunately wireless practice of my script for my Flash presentation - working remote in hand!  Take care.

• Cannot get the USB to work HP G6-2278dx

  My girlfriend just bought the HP 2278dx g6 with pre-installed Windows 8. Unfortunately, she's not worried about her and is pretty set on Windows 7. So I bought his windows 7 Ultimate and installed on his computer. I downloaded and installed all the drivers I could find, but I can't the usb on the left side of the computer at work. In Device Manager"also of shows me some other stuff that does not work (I would like to list, but she of not here right now and has the computer with it and won't return until Wednesday)

  I thought it would be a chipset or something I need to download, but NOWHERE on the internet find a chipset for the HP g6-2278dx win7 64-bit. Sort could someone help me? (btw, the only usb that works is on the right side next to the power input charger.)

  I just installed Win 7 Ultimate 64 bit version on my G6-2278dx. For me to get my USB 3 ports to work, I installed the drivers for the AMD chipset from this page.

  http://support.AMD.com/us/gpudownload/Windows/pages/raid_windows.aspx#2

  I believe that the network card is the 8168 8169. I don't remember the hand. You would like the Win7 and WinServer 2008 R2 driver (Version 7.065) I'm not on my laptop, so I'm out of memory which is not always good. Wireless network card works since the drivers used by Windows 7 if I remember correctly, because that's what I used to download all the drivers I needed for the other stuff.

  I'll have to check which driver I used for wired LAN port, but you can get them from Realtek on these two pages.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  and or

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• Which TV Tuner/Capture card?

  Hi people.
  Here is my Config to the computer.

  Intel Core i7 920
  Gigabyte GA-EX58-UD5
  Corsair 6GB @1333

  Tagan BZ 800W PSU
  Sunbeamtech RTC 120
  XFX Nvidia GTX260
  Hauppauge WinTV PVR 150
  Seagate 1.5 TB * 2 + 1 TB HARD drive
  Vista 64-bit
  NAGRAVISION NAC - 510i STB (Set top box)

  What I need to know, is what card TV Tuner/Capture internal should I go for as the Hauppauge WinTV PVR 150 does not work well beyond 4 GB of RAM. To use it, so I need to limit my RAM less than 4 GB.
  The quality is good enough to view and capture. But I don't want to use the work around or reduce my RAM.

  Please suggest me a good internal TV Tuner/Capture card that works with my PC config and allow good capture. I also intend to upgrade to Windows 7

  Current models available in India:
  Hauppauge WinTV USB2-Stick TV TUNER CARD
  Hauppauge WinTV HVR-1100 internal
  Hauppauge TV Tuner card
  Hauppauge Win TV PVR USB2 MCE Kit - OEM
  Hauppauge MediaMVP
  Hauppauge WinTV-PVR-350 TV Tuner card
  Hauppauge WinTV-PVR-500 MCE TV Tuner card
  Hauppauge WinTV PVR 150 MCE Kit - OEM

  Note: I have a Coolermaster CM690(Mid-tower) because of who I am able to use only one PCI and one PCI-E slot. I need a PCI card. Or external case.

  PS. : I can try and a delivery from newegg or amazon to my country

  It's really a personal preference type of question.  You might consider contacting the manufacturer is to see the compatibility of Windows 7 is going to be.  Regarding delivery to your country it is a question to ask the retailer you are dealing with. Locutys of Borg

  Resistance is futile

  If you don't succeed the first time skydiving probably isn't for you!