Types of routing

Similar Questions

• Information on the types of routing of reception

  Hi all
  
  
  I work on purchase order receipts and internal applications.
  
  
  There is a field named 'Type of routing of reception' at the level of the line in. (its there at several levels as organization, point, IN. level)
  
  
  There are 3 Types
  
  1 standard reception
  provider-> inventory sup
  
  2. direct delivery
  provider-> receive (put in area)-> inventory sup
  
  3. inspection required
  provider-> reception-> inspection (done)-> void inventory area.
  
  
  But if we create the reception for the types of Inspection Standard, - 1 transaction creation with DELIVERED line in the rcv_transactions table and onhand quantity is not incrementing.
  
  If we create direct delivery receipt - 2 transactions creation with DELIVERY and RECEIPT of the rcv_transactions table and qty onhand lines is growing.
  
  Can you tell me when the Inv qty wil be incremented for Standard, routing of Inspection types. We need to run other programs or something to do inorder to increase th inv Qty
  
  
  Thank you inadvance.
  Ramz js

  Hi Matt,

  I think you have the options a little mixed up, so I changed to what is the feature according to the routing option. I put in the source or location and () operation that goes from the goods. Once the DELIVER bit runs the wty Inv is increased. DELIVER is done manually with Standard, Inspection required routing options.

  1 standard reception
  provider (reception) receiving void inventory area (delivery)

  2. direct delivery
  Directory of sub suppliers (reception and delivery)

  3. inspection required
  provider (reception) inspection (inspection) inspected/reception Area (delivery) void inventory.

  / Niels LM

• Routing of signals DAQmxCfgSampClkTiming

  Is it possible that I can find what type of routing not DAQmxCfgSampClkTiming between two boards?

  I use the ANSI C interface and analog output PCI-6733 (series AO) two boards connected with a RTSI cable.  I tried following suggestions on the manual on the device making slave have the same clock from 20MHzTimebase and I kept getting error "there are no more resources for this course" type of messages.

  It was not up to what I've avoided any type of signal explicit routing and just used "/ Dev1/ao/SampleClock" as the clock source sample on the slave (Dev2) device that the analog compiling output began to work (after the reset of the device, BTW).  I'm just curious to see what kind of signal routing DAQmxCfgSampClkTiming has put in place under the hood.

  The test program seems to work well and signals in sync, but I want to make sure I am configuring correctly.

  The DAQmxGetExported... Features of the term show nothing since I imagine that it is all related to the task rather than the immediate delivery. The DAQmxGetAO... functions do not seem anything to know the routes.

  Thank you

  One last thing: PCI-6733 uses the chip of TCC, which is what use the E series devices.

• How can I change the password of the wireless router?

  Original title: change password

  Hello, I need help to change my password wireless internet please. I'm not very computer saavy, so I would appreciate simple instructions, please. I have a regular computer, I don't have a modem, a wireless router, access to, (husbands), a printer, my laptop? the cable company, son-in-law has compressed & PS3.  The problem is my stepson is autistic and mentally not mature enough to be on the internet and he knows the password. How can I change the password to the wireless internet? Then I'll also have to change it on printer, phone, ect... Or y at - it an easier way to keep, before taking any electronics away from him? Thanks :)  WeigeSS

  Go to http://whatismyipaddress.com/ and copy your IP address. Then open a webbrowser and paste the IP copied into the address bar. You must now enter your username and password (most often, it is not a WiFi password, but that this service provider you have given - it could be written on the contract or manual). Now, everything depends on what type of router you have. Usually, there is a security link or password somewhere on the screen. Click on it and then you can change the password.

  If you need further help, feel free to respond.

• Replacement of a Cisco router

  Hello

  I plan to replace a router No. 2851 to one of our sites, but am a little concerned by the configuration of the VoIP on it.  Wouldn't be enough if I just copy the current running configuration than one that is for the new router taking into consideration differences in interfaces between old and new routers?

  Thank you

  Hello

  Yes, you can copy and paste the config from the old to the new, as long as you replace it with the same type of router and the same components of voice.

  HTH

• For the button routing rules backup in a VRRP/configuration topology

  Hello

  I would like to know which is the best solution to the following:

  A switch (5412zl) has a static route based 0.0.0.0 common to the firewall.
  The main switch is directly connected to the firewall via a standard rj-45 network cable.

  Should what type of routing configuration I on the emergency switch, so that the traffic passes to the firewall if the switch is not available?

  Thanks in advance for your help.

  Hello:

  You can also ask your question in the Forum of HP Business - section LAN routing Support

  http://h30499.www3.HP.com/T5/LAN-routing/BD-p/LAN-routing-Forum#.U5eFAP1OXGg

  or ProCurve switches section / focus on delivery.

  http://h30499.www3.HP.com/T5/ProCurve-provision-based/BD-p/switching-e-series-Forum#.U5eFL_1OXGg

• ISAKMP error - 2811 router

  Hi guys,.

  I would like to create a VPN site-to site between my ASA and a remote router in China.

  On the router, when I typed ""crypto isakmp enable ' command I know that isakmp is not present. "

  What can I do, where is the problem? License, ios image,...? !

  error type:

  Router (config) #crypto enable isakmp

  ^

  Invalid entry % detected at ' ^' marker.

  Router (config) #crypto?

  CA Certification Authority

  main activities key long-term

  public key PKI components

  commissioning Secure Device Provisioning

  Wui Crypto HTTP configuration interfaces

  News of the router:

  Cisco CISCO2811C/K9

  Version 12.4 (13r) T13, RELEASE SOFTWARE (fc1)

  c2800nmc-spservicesk9 - mz.150 - 1.M7.bin

  Thank you very much.

  Luca

  To configure the site to site VPN, or any other VPN, you need advanced business picture, advanced security or Advanced IP Services.

• iPhone 6, wifi connection

  I have an iPhone of 128 GB with iOS10 6. It has always been slow to the point of connection to routers or does not connect and a recent visit to the USA took out that frustration. I was trying in vain to search Hotel / b & routers b on my phone, so my Kindle and 6 s the iPhone to my wife by my phone would be in touch immediately with a strong signal. I tried to reset the network, as I did several times in the past year since I bought the phone, and which makes no difference whatsoever.

  I have also read and followed the advice on these talk pages, with no improvement.

  I put my phone next to my wife, my iPad device 2 and my Kindle, all connected to our relatively new Netgear router upstairs, and my phone usually has a weaker signal and is slower to connect.

  He is sitting on my desk that I type, the router being under the desk, and the signal is strong at 3 bars with no dropouts.

  I'm running out of ideas, and I think it's maybe a rogue phone.

  You must first check your Wi - Fi router: check if other devices can be connected. This will let you know if there is a problem with your Wi - Fi router. You can restart your router and restart the connection to WiFi.

  Make sure that Wi - Fi and you can see your network

  Go to settings on your iPhone > Wi - Fi and check if it is enabled. And if there is a blue check mark next to a network name means that your iPhone or iPad was connected to this network.

  Restart your iPhone/iPad, router, cable/DSL mode

  If this does not help, reset your network

  On your iPhone, iPad, got to settings > general > reset > reset network settings. This will reset Wi - Fi networks and passwords, cell parameters and VPN, and APN settings you used before.

  These measures should help.

• That means "another device on the network use the IP address of your computer"?, that means "another device on the network is using the IP address of your computer?

  That means "another device on the network use the IP address of your computer"?, that means "another device on the network is using the IP address of your computer?

  A

  Most likely, the computer becomes a network address of a router. The assignment of an address ("lease") expires and must be renewed after a certain period of time, which could be an hour or a day. The lease expired without being renewed because the device has been disconnected at the time. Meanwhile, the address has been leased to another device on the network, or maybe the router has not updated its list of addresses the leases. When the device offline comes back online, a conflict results. Depending on the type of router you have, the conflict can resolve itself automatically. If not, then in the menu bar, select please

  ▹ System Preferences network ▹ 

  If the preferences window is locked, click the lock icon in the lower left corner and enter your password to unlock it. Click the Advanced button, and then select the TCP/IP tab in the sheet that drops down. Look at the menu option

  Configure IPv4

  If the selection in this menu is

  Using DHCP

  Click on the button

  Renew the DHCP lease

  Test.

  Make sure that you have more than one DHCP server on the network. That could happen if you have more than one access point Wi - Fi, or if you have a router and broadband a wide device distinct in connection mode sharing.

  B

  Less likely, you have a network address that you assigned yourself and another device is itself by assigning the same address. In this case, the selection to configure IPv4 menu will be either manually or using DHCP with manual address. This kind of conflict will not be resolved automatically. You have the following options to solve:

  1. Change the selection in menu using DHCP.
  2. Change the address assigned manually to one that is not used by another device.
  3. Change the address of the other device.

  Which of these options you choose depends on the details of why you use a static IP address. Any changes you make to the network settings is necessary before taking effect. To do this, click OK, and then click apply.

  If the router is also your device at wide band, then he may be operating in bridged mode. In this case, only one customer at a time will be able to connect to the Internet. Consult the manufacturer or ISP documentation for how to reconfigure the device in the connection mode sharing.

  C

  According to a report a "DirectTV" receiver can cause the problem. If necessary, disconnect the device from the network, or power off and test. Consult the support services provider.

• SOLUTION for your HP printer disconnect and/or constantly disconnecting from the network

  If you are having a problem printing, scanning or fax with any HP printer because of this be disconnected and constantly disconnecting from the network, here again is the fix!

  I thought that this all after several failed attempts with HP Support, my Internet access provider and various troubleshooting tasks including reinstall the HP software and more and more.  Well, through self teaching on internet and exhausting search for 6 months, I FINALLY thought to it.  OMG!  I'm a paramedic (not IT) and a little computer but far not an expert.  I have all of you here!  Nobody seems to have the answer, but I'm sure that I'm doing it to 97%.  Whatever it is, if it please answer and let me know that it worked for you!  :-)

  It doesn't matter if your printer is installed cable or wireless.  You don't reinstall your software, no recycling power of your printers or your router/Modem.  Your printer is unstable on the network and continues to log out or disconnect from the network it is NOT because the software is glitched, it isn't a firewall problem by saying, is not a router problem, is not a problem with your power cord, because most networks use a 'Beach' and IP addresses for security reasons This kind of "cycles" the IP addresses of the devices to reduce the risk of an attack.  A printer is not a threat, but the 'network' don't own human intelligence, so he does not know this.  Here are my step by step instructions on how to basically your printer address IP (static IP) instead of change back through a cycle so drop your printer on the network or disconnected.

  Funny, if you're someone who has had the elements in your print queue, they will not print, and you turn your printer off and on again and suddenly your print... well documents, join my club.  The reason it works is that when you turn on the printer, it starts with the same IP address before cycle.  If you are someone who is sitting there for a while and all of a sudden your printed documents without changing you something... it is because through the cycle of change of IP address, it hits your printers IP address and the network would allow him to print.  Not very funny, I know.  It took me forever to figure out why my printer would print sometimes, but not always.  Since I thought at this point, I can SCAN, PRINT, and use all the features of my HP software installed like HP, Photosmart Essentials Solution Center.

  On your printer, go to menu/Setup/network and press OK.  In the network menu, print a "network configuration page" so you can see the IP address and other settings of your printer.

  Now, back to the main menu on the screen of your printers.  Or you can go to your web browser and type the IP address using decimal numbers too and this will take you to the web page of your printers.  Choose: setup\network, then press OK.  Look for the IP settings and press OK. Choose "manual" instead of "automatic". Manually enter the IP address it as well as the default gateway that you can see the Network Setup page you printed earlier.  Note: If you manually set the IP Address of the printer, make sure that it is outside the range of your router's DHCP. Otherwise you might encounter a problem with IP addresses on your network duplicate. (If you don't know how to do this, write back and I'll explain).  Don't forget to click "save changes".  Now, restart your computer, and print just what you want.  :-)

  A trick I often use with DHCP network printers:
  In printers and faxes, right-click on the printer and select "Properties".  Click Add a new port.  Choose standard TCP/IP port configured for the host name of the printer. Read the host name of the network printer configuration sheet.
  
  Using my method means that you always connect to the printer even if its IP address changes (which can happen with the dynamic configuration). This does not jeopardize the security of your network.  It shows just your printer to stay put and stop traveling the highway of IP address.  :-)

  The DHCP range is the range of IP addresses that the router distributes automatically as devices to join the network.  The DHCP range is determined by the router and each brand has a range that is set at the factory (which can be changed by you).

  Default value for the DHCP of your D-link is 192.168.0.100 to 192.168.0.199.  Thus, outside the DHCP range est.2 a.99.200 a.254.

  Is a handy cheat sheet attached.

  You can change this interval by entering the router settings page - type the router's IP address in a browser, enter the login information and access the DHCP parameter area (varies depending on router, hunting around).

• NB510-108 problem with wireless and lan controller

  Help, please!
  (answer in German would be nice, ill try English first tho)

  I installed ubuntu 12.04 on my toshiba NB510-108 (PLL72E-00R011GR) and then I was not able to go online via wlan or lan same kable.
  After some effort to install the drivers through ubuntu I have installed windows 7 starter edition back but now windows does not install the ethernet / wireless drivers realtek or atheros network device.
  so I tried to install all the drivers wireless by http://toshiba-asia.com/sg/support/drivers/ but now when I try to run these drivers after loading them down windows 7 cannot install correctly, it says that there is a compatibility issue. I tried to run these drivers in compatibility mode for win xp sp1 and win vista sp1 without success.

  Also, I installed all the drivers for my model of http://de.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=DE here with some of them have been properly installed and even when I get my system to a point where I find the two network devices work as 'good' in my windows Device Manager, the following problem occurs again:

  I can't find any of my netbook WiFi network (wlan is enabled via fn + f8) no matter what type of router I try to connect. other laptops have about no problem connecting to routers so that can't be the issue. When I click on the windows just below the wlan troubleshooting info it only says no problem could be identified (the system is in German, so please excuse my translation)

  In the information system components and devices of problem the pnp for the ethernetcontroller said pci\ven_1969 & DEV_1090 & SUBSYS... and for the networkcontroller: PCI\VEN_10EC & DEV_8176 & SUBSYS...
  If it is useful. I also wanted to put my dxdiag online file, but this extends the limit to 3000 characters.

  Someone here could help me please? It would be really nice

  Hello

  I m wondering why you have the same problems of connection using WLan and LAN.
  I mean its not really necessary to configure anything to get a connection to the local network works.
  The router must support, and DHCP must be enabled in order to assign the IP address automatically.

  I recommend that you check the TCP/IP settings in your network WLan and LAN connections.
  In TCP/IPv4, you can view the properties. The INVESTIGATION period and all other options should be set to assign automatically. You should also disable/uninstall the TCP/IPv6 and must use TCP/IPv4

  By the way: you have an antivirus and firewall software installed? If so, remember that the two don't affect the WLan/LAN connection.

• Weak WIFI signal

  Hi, am currently using an HP Pavilion 2307tx g6 but get really weak wifi signal in my room. Only able to get about 2-3 bars every time while my other laptop can go up to full bars.

  Any help/solution would be greatly appreciated!

  Welcome to the HP Forum, Rascal.

  Discussion on the theme of the power of the Signal

  Buffaloes by themselves may be a little empty of meaning, UNLESS you can interpret the definition of what each 'bar' says.

  Signals are affected by the type of router you have - routers are NOT equal.

  • The cheapest router can not not the support required for the performance of your computer's wireless card.

  Example: An older router that only supports 802.11 g will not provide faster than 54Mbps - even if you have the best card you can buy in your computer.

  • The opposite can be true as well - a good router cannot provide a better service than the computer's wireless can support.

  Example: If the card in your computer is 802.11 g, so even if you have a router capable of speeds of more than 300 Mbps, you can get only 54 Mbps.

  Speed and autonomy are limited by the link in the chain.

  • 802.11n is faster than the 'g', but it can also be slowed by the walls, the furniture in metal and other obstructions.
  • Move your equipment, even a few inches, could make the difference to a router 802.11 g

  AND

  • The same might be true for a 802.11n router that has a small antenna (low power)
  • Antennas in routers are NOT equal.  Small antennas in routers fantasies can still match a whimpy router.  You want a router with a 5db antenna 7db (or better if they make these by the time you read this).

  Assuming you bought the biggest, baddest, best wireless available for your computer, then you may need to upgrade your router.

  Strength vs. Signal bars

  Bars can indicate how things are moving along, or they can cloud the issue - depends on the "bars": which generates the bars, the sensitivity are the bars and you can do a lot in a bar anyway?

  You can use another measure: the traction measured in percentages, detection and Signal type:

  WirelessNetView v1.50 - wireless network monitoring tool

  WirelessNetView works on Windows 7 and Windows 8 - there are a few problems with XP: read reviews of the author.

  ---------------------------------------------------------------------------------------------------------------------------

  You can try to update / reinstall your Wireless driver.  Help - can be a waste of time.  If you have already done, this new fact will not help - so I don't recommend it.

  Reading:

  Laptops - troubleshooting Internet or email connection on a wireless network with Windows 7

  Windows 8 stops responding or becomes very slow after you connect to the Internet

  Reference:

  Description 802.11n 802. 11-802.11 g

  Date approved	June 2010	2001	2003
  Frequency band	2.4 GHz	5.0 GHz	2.4 GHz
  Speed	100 - 200 Mbit/s	Up to 54 Mbps *.	Up to 54 Mbps
  Estimate 128Mbps	Estimate 128Mbps	27 Mbps	20 to 25 Mbps
  Range 1	range of 230 ft	range of 60 feet	100 ft range
  Modulation technique	Multiple input multiple output (MIMO multiple) and channel-bonding/40 MHz	Orthogonal Frequency Division Multiplexing (OFDM)	Spread Spectrum (DSSS/PBCC)
  Interference problems		Less interference than 802. 11 b or g	Increased interference (mobile phones, microwave ovens, ovens, etc.).
  Maturity of the product	Official specification will be finalized in June 2010		Official, final specification in June 2003
  Distance between Access Points		About every 50 ft	Depends on configuration
  Biggest advantage	More high speed and battery life	Higher speed	Top speed coupled with 802. 11B compatibility

  Help, Suggestions and examples:

  Parameters to improve wireless connectivity

  Articles, various, including:

  • The power of WiFi management
  • Laptop wireless hesitates or don't stay connected when executing a stack

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  Fixed / responded? Click this post accept as Solution to help others find answers.

• Qosmio F20 - WiFi does not work

  I have a Qosmio F20 and recently wi - fi would not work att all or don't work only very rarely. Couple that with the fact that Norton Internet Security has recently kept maxing out the cpu then we disabled from running in the background.

  We tried to set up the network again, we took all the security on the router but Tosh will only see the network if it is directly connected to our router linksys with ethernet cable.

  I took the step of disabling the adapter wi - fi built-in and loading top/installation of the linksys phone adapter that we use for our other laptop HP (older). Even that kept dropping out, connecting for a few seconds at a time, but it was beautiful when he was back in the HP.

  Can someone help me on this one?

  Hello

  did you check if your router does not work properly? And make sure that tries to connect with another access point to verify if you really can't connect with your built-in wireless card.
  May I ask what type of router you have?

  An update of the firmware on the router is sometimes useful.
  Otherwise, try to reinstall all the wifi tricks related like drivers and software and try again, because wifi can be sometimes very tricky.

  Welcome them

• Apple TV 4th generation very slow to load movies (MP4)

  I get a 4th generation Apple TV to replace my old Gen 3. When I try to load a movie from my iTunes Library (on my Mac Mini), it really takes a lot of time to start the movie or it doesn't start at all. This unit is connected to the same network as my older Apple TV which plays MP4 files without any problem. Everyone knows about this problem? I'm running the latest available updates. All other features, including playing movies from iTunes or Netflix app work fine.

  I had problems with home sharing, usually. I'm on my second unit.

  What type of router you are using?

• Billion BiPAC 7300 G with C6380 wireless issue

  Hi all

  Pulling my hair out here!

  I tried to connect using the wizard of printers, but the printer could not find the wireless router.

  The router is 802.11 g (not sure what that means) that I need to change a setting on the router?

  I use Vista

  I had to opt for USB at the mo I need to print some documents.

  Anyone know if I bought the wrong type of router?

  Thank you all so much for your time reading this!

  The BiPAC 7300 G should work just fine with the C6380.  Log in to the 7300G (IP address default to 192.168.1.254, username: admin, password: admin) and check that:

  1. The WLAN service is enabled
  2. Mode is set to 802. 11 b + g
  3. Hide ESSID is disabled

  What is the regulatory parameters of field and channel for your wireless router?

  In addition, I want to check that you do not see the 7300G's wireless-network of the C6380 wireless configuration wizard.

  BTW - what is the SSID of your wireless router?