Unable to access backup after system restore.

Similar Questions

• NEED DRIVERS AFTER SYSTEM RESTORE

  HP Pavilion g6-2128tx Notebook PC 
  Serial number: 5CD2231LJF

  {Information}

  After system restore a bunch of drivers was missing, I managed to update some drivers but I need some I can't find. Help!

  Hardware ID

  Ethernet controller:

  PCI\VEN_10EC & DEV_8136 & SUBSYS_183E103C & REV_05

  BCM20702A0

  USB\VID_0A5C & PID_21E3 & REV_0112

  PCI device

  PCI\VEN_10EC & DEV_5229 & SUBSYS_183E103C & REV_01

  PCI Simple Communications controller

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_183E103C & REV_04

  SM Bus controller

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_183E103C & REV_04

  (USB) Universal Serial Bus controller

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_183E103C & REV_04

  I run on Windows Ultimate-64-bit

  Help would be GREAT

  Hello

  Download and install the following.

  Chipset Driver - Windows 7.

  After this Setup is complete, restart the laptop.

  Realtek software LAN.

  Broadcom Bluetooth 4.0.

  Realtek card reader driver.

  Intel Management Engine Interface.

  Intel USB 3.0 Host Controller Driver.

  Kind regards

  DP - K

• Where am I going to access the the system restore on my Vista "help and support." It has been easy on XP!

  Support under XP system quite simply, I went to 'Help and support' clicked on it, and a new screen open and followed the easy prison. Where am I going to access the the system restore on my Vista "help and support."  I just want to go back to a previous restore point.  Thank you!!

  Hello

  Start - All Programs - Accessories - System Tools then system restore should be visible.

  Also, a lot of PC brand have a restore option of the system via F8 at startup, and then click "fix." Useful if you cannot start Windows successfully.

  Also you can click on start and then just type rstrui.exe and press ENTER.

  Please mark this as useful or response if applicable.

  Tricky

• Impossible to uninstall Symantec Endpoint Protection after system restore

  Hello
  a program has been uninstalled (Symantec Endpoint Protection)
  After have rebooted and still have problems to install a newer version, I decided to do a system
  Restore prematurely, I uninstalled the original version.
  (Since I couldn't find the installation files or my license info)

  The old version worked again.  Now I am able to start the
  new version, the old version will not uninstall.

  It just sits there in a small box with a bar saying Windows of progression
  in the configuration of Symantec Endpoint Protection and it remains as it
  for as long as I left, at least 25 minutes.

  I thought that the system restore would put things back exactly as they
  have been, but it's apparently not the case.

  OT: Impossible to uninstall after system restore

  Any ideas on that?
  The OS is Windows 7 Pro 64 bit 64-bit.
  I found this, but have not yet tried.
  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/en-us

  I was able to cirumvent the problem by a selective startup in Msconfig.

  I disabled all startup items, all services not MS, restarted and then uninstalled

  successfully.  However, I met another strange problem.

  After uninstalling old version, I rebooted (the system was still selective

  startp) I put a new restore point and installed the new version successfully.

  Later, realizing msconfig has been arrived at "selective", I went and

  has tried to return to Normal startup.  However, when you select normal

  and hit 'apply', it immediately jumps to selective.  I have never seen it before.

  I didn't know how to solve.

  Instead, I uninstalled the new version of the AV program, jumped to the restore point

  I did before I installed, rebooted, open Msconfig and have been correctly set up

  In normal mode.  Then reinstalled the AV.

  Everything is OK now.

  You ever heard of this problem of msconfig before?

• My seagate backup more external hard drive not recognized after system restore

  I have a small sony vaio netbook running windows 7 starter edition. I did a system restore recently - saved on an external hard drive usb, nine 1 to seagate backup more - now after fighting with 124 updates hard disk is not recognized. Seagate has say the drivers are pre installed in windows. convenience stores never work - I find the trouble shooters are almost always useless - is this just me?

  It works on my laptop of friends - so im guessing it is the operating system reinstalled - what I do?

  Hello Neil,.

  First of all, we apologize for the late response.

  1. What happens, do not install the updates?
  2. What is the complete error message you get, when the update installs?
  3. What is the update kb article number?

  
  for problems with windows updates, run the tool in troubleshooting Windows Update:
  Open the Windows Update troubleshooting tool
  http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Update-Troubleshooter
   
  For the problem with the external hard drive
  Code 28 shows, the drivers for this device are not installed.
   
  Error codes in the Device Manager in Windows
  http://support.Microsoft.com/kb/310123/en-us
   
  Log in as administrator and then try to install the drivers
   
  How can I connect as an administrator?
  http://Windows.Microsoft.com/en-CA/Windows7/how-do-i-log-on-as-an-administrator

  S eaTools for Windows

  http://www.Seagate.com/in/en/support/downloads/item/SeaTools-win-master/

  Additional information:

  "Access denied" or other errors in the access to or work with files and folders in Windows

  http://support.Microsoft.com/kb/2623670/en-us

  I hope this helps. Please get back with the results.

• Unable to create point of system restore, System Image & System Repair Disk

  Hello

  I'm on HP Pavilion dv6 notebook, Windows 7 Edition home premium, (Intel core i7, [email protected] Ghz) CPU, RAM (4.00 GB).

  2 days back, I installed kaspersky IPSec 2016.

  After installation of this I started to experience different startup issues as initially I wasn't able to open the application (word, excel) Microsoft, infact I wasn't able to work on any application, even could not shut my system.

  today when I started my system again to check again the question that I was surprised to see that I could access my Microsoft & other applications.

  As a preventive measure, now I want to do system restore, disk image point & system repair disk but unfortunately, I am not able to do this.

  Here are the problems I face to create above.

  1 system restore point - specified error as ' restore point could not be created for the following reason: a volume shadow copy service component has encountered an unexpected error. " Check the event log applications for more information (0 x 80042302)

  2. System Image disc - error indicated as "Windows cannot find device backup on this computer. A volume shadow copy service component has encountered an unexpected error. Check the event log applications for more information (0 x 80042302)

  3 system repair disc - of the errors illustrated as "system repair disc could not be created. The parameter is incorrect. (0 x 80070057).

  Pls advise.

  Thank you for the update from us.

  The message you get may be caused by a corrupted system file. We offer you to perform analysis DISM that can help resolve the corruption of Windows error.

  Let us know how it goes.

  Kind regards.

• Satellite A500-1CO - loss of data after system restore

  Hi all, because the system was slow I decided to restore the system using the DVD of restoration system (1,2). The problem is that I have not saved anything from drive D, and after the restore, all files have been deleted. My logic was unaware that the restoration apply to drive C (system disk) and let the D drive as it is, but I was so wrong.

  Is there a way to recover all or part of the lost data?

  Please help me. Thank you.

  Hi mate

  Unfortunately, I think that there is not much to do now.
  Recovery DVD redefines the laptop to factory settings and, therefore, this disc format the whole HARD disk and also all the partitions and, therefore, you will lose all data if you n t backup this before starting this procedure.

  You should read the user manual or information before starting the recovery. :(

• M57 6072CTO no usb after system restore

  I just did a system restore by using the disks IBM XP SP2 and none of the USB ports is enabled once windows starts to boot, os I have no keyboard or mouse and no other way to access the computer.

  No idea how I can get around this (there is no PS2 Connector)

  Thank you

  Peter

  The problem is I was impaitent Walker do the restore I that the aircraft had crashed so not restarted so no usb.

  I did the restore of the system again and he left running while doing other work, and that's all OK after that

• After System Restore Windows XP behaves strangely, said wininet.dll must be installed

  original title: XP startup problem

  My computer was slow, so I did system restore at an early date.  The system worked better, so I system restored recently.  Now the computer will just go up to my screensaver.  Does not start.  I can access taskmaster; but I am unable to run anything or to find beginning.  I have been informed that wininet.dll must be installed.  How can I restart or restore this computer.  I have windows XP.

  Hi ThomasCline,

  Try to boot your pc in safe mode to see if it works properly. http://support.Microsoft.com/kb/315222

  If everything works properly in safe mode, you need to configure your pc in clean boot mode. http://support.Microsoft.com/kb/310353

  If all above fails, try running the SFC, you are able to open the Task Manager, click application-> new task & Type-> sfc / scannow-> ok

  You will also need your cd of windows xp for this repair.

  I hope this helps...

• Windows Vista - what should I do after system restored?

  My home edition vista recently will not start. After I turned it on, it loads for a while and stops automatically. I tried pressing some buttons for example F2, F8, F10 function for repair and recovery, and it is able to load the previously saved startup page. After that I turned it off, it cannot start again. I tried twice on the recovery of reparation and restored successfully, but now the repair and recovery seems no longer works.

  (1) what should I do if I managed to open the start page?

  (2) what could be the cause of it? In any case to restore so that it will work like new?

  Hello

  See if that helps you.

  Startup Repair options.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  Reinstall options.

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  ___________________________________

  And if you have never received a recovery disk when you bought your computer, there should be a recovery on the drive Partition hard reinstall Windows how much you bought your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Them or us ask the right sequence of key.

  ___________________________________

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• How to save important files a files on a dvd before doing a restore of the entire system with factory.so disk I am able to reinstall computer after system restore.

  I need to do a restore of the entire system with disc received from factory.but that I have personal files and folders that I need keep.such as banking, contacts, photos, ect. ect. How do I put them on a dvd a restore then their return after the full system restore

  Hello

  If the system still boot and CD/DVD Burns just put in a DVD-R (write once) or DVD - RW (burn
  several times)-it will encourage - when its ready use Windows Explorer to drag and drop files (and
  their content) on the DVD. When you're ready, click BURN. I would like to make a couple of each DVD for
  Security with redundancy. These will not be encrypted and you can access the files out of them or
  subsequently copy on a hard drive.

  Basically, make sure you know what you want to copy the files and put them in a blank DVD to write.

  ---------------------

  If the system does not start, then you will need to put the drive in another computer or in a
  External enclosure USB so you can copy files to removable media.

  ---------------------

  Burn a CD or DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/b47eb51a-ea6d-4d97-97b0-2d07a59316981033.mspx

  How to burn a CD with Vista
  http://ITsVISTA.com/2006/12/ITsVISTA-Tip-10-how-to-burn-a-CD-with-Vista/

  Burn a CD or DVD in Windows Vista
  http://maximumpcguides.com/Windows-Vista/burn-a-CD-or-DVD-in-Windows-Vista/

  Microsoft video - how to burn CD/DVD
  http://www.YouTube.com/watch?v=0BwF60m05m8

  Excellent Forum for help with programs and CD/DVD problems
  http://Club.cdfreaks.com/

  Burn a CD or DVD in Windows Media Player
  http://windowshelp.Microsoft.com/Windows/en-us/help/30ffa641-B682-4315-8c7e-8a29f383a7131033.mspx
  Burn a CD or DVD in Windows Media Player: frequently asked questions
  http://windowshelp.Microsoft.com/Windows/en-us/help/51a88740-Abda-4144-9176-cec79cca31e81033.mspx

  Burn a CD or DVD in Windows Media Center
  http://windowshelp.Microsoft.com/Windows/en-us/help/9ee6cb78-bd7e-4DE3-A154-82d40c4289e01033.mspx

  Burn a CD or DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/b47eb51a-ea6d-4d97-97b0-2d07a59316981033.mspx
  How to burn an Audio CD - see also related Articles
  http://www.vista4beginners.com/how-to-burn-an-audio-CD
  Burn a CD or DVD using Windows Vista - a video
  http://www.YouTube.com/watch?v=0BwF60m05m8

  Disc burning: frequently asked questions
  http://windowshelp.Microsoft.com/Windows/en-us/help/2fa35b0d-B280-4589-9805-55e753888f5c1033.mspx

  Should which CD or DVD format I use?
  http://windowshelp.Microsoft.com/Windows/en-us/help/2af64e60-60AA-4d79-AB6C-3a5db5806cbe1033.mspx

  Windows Media Player playlist: frequently asked questions
  http://windowshelp.Microsoft.com/Windows/en-us/help/4bf0d986-a1cb-40d2-94de-85dba30a83831033.mspx

  Get the most out of WMP11http://windowshelp.microsoft.com/Windows/en-US/mediaplayer11/default.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• No Internet connection after system restore

  I had problems to open Windows Live Messenger last night, and I tried to do a system restore, as I noticed there were a couple of updates that have been installed throughout the day where I suspected may have caused the problem.

  I went back to a restore point from the earlier in the day when I heard that Messenger was working. Of course, Messenger open instead of crashing on startup.

  Unfortunately, I am able to connect to the Internet. Network connections settings say it's "id" my wireless network, but nothing changes. Is no longer, I get an IP address. I have other computers on the network that connect without problem.

  I tried to install a Wireless N USB adapter and the problem still remains. Finally, I gave and did a complete restore to factory settings. Good news is that I can now get a connection. Fortunately, I had my backup files.

  Research online, it seems that many people seem to have had similar problems, but not after a system restore.

• File missing after system restore

  Dear Sir.
  Today, on a tecra M2, I did a system restore, but suddenly, the message came that I had to re - install the following file: \system32\ntoskrnl.exe :

  How can I do this: put in the recovery cd or just make a formatting the drive with the restore cd?
  Thanks in advance
  drweekx

  Hello

  System Restore is a very useful tool, but it is not the miracle solution! :-)

  Your "ntoskrnl.exe" file seems to be corrupted and this file is very important as you BONE!
  You can try to start Notepad, and then press the key "F8". This will take you to a menu and you can choose the 'last known good configuration"and the VGA Mode.

  If you are lucky your laptop work after that, otherwise you can only recover the portable whole! But if you have important data on the NB you safe to an external drive!

  Goodbye Chris

• Cannot run some programs after system restore to remove the virus

  Hello

  Toshiba my duaghter had a nasty virus that pretends to be an antivirus software product, which sneaked in, between the time his default service Norton has expired and I had the time to install Trend.

  Can not remove it using trend, so on the advice of a friend, decided to make a windows system restore to a point before the infection. It worked successfully and the virus has disappeared, but now she can't run some programs, I tried to reinstall Trend, but fails because he says you must first uninstall Norton. But I can't run Norton, or uninstall, and certain folders on C: are no longer accessible.

  I have to do a full restore of the Toshiba System (IE back tofactory settings? This seems a drastic measure, but the issue is beyond my meager knowledge of PC.

  Thank you

  Graeme

  Hey Buddy,

  Hmm... This announcement is a bit confusing... Maybe the programs you want to say were installed after the system restore point, who knows?

  In my opinion you must reset the laptop configuration that you have already written. This will restore the pre-installed Windows version where everything is working correctly and that all the drivers and tools are installed.

  Therefore, you only need the Toshiba Recovery disk and boot from it. This will restore the factory settings.

  Check this box!

• DV6 - 6153cl drivers for biometric devices missing after system restore

  Hello

  I have a HP Pavilion dv6 - 6153cl Entertainment PC with Windows 7. I used the fingerprint reader, since I have my laptop. The scanner has stopped working.

  Background: two weeks ago, I downloaded the latest version of Norton 360 (Version 21.1.1.7), which caused my laptop to keep crashing every few hours. After much time consulting technical support, I did a system restore to a few days before the new version download then downloaded the version of Norton 360 and active. This solves the problem of crash.

  Problem: After restoring the system, my fingerprint reader no longer works. By control panel > all Control Panel items > biometric devices, "Windows do not have the biometric devices on this computer. You will need to attach your device or install device drivers. "Can someone tell me what are the correct drivers that I need and where to find them?

  Thanks for your help!

  Hello

  First of all, download and reinstall the driver Validity Sensor on the following link.

  http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55109.exe

  Once completed, restart the laptop.

  If it still not works, you may also need to reinstall HP SimplePass on the link below.

  http://ftp.HP.com/pub/SoftPaq/sp54501-55000/sp54680.exe

  Yet, when it has installed, restart the laptop.

  Kind regards

  DP - K