Unable to connect to the Web comments via browser host server or by using NAT mode or bridge

Similar Questions

• Unable to connect to the web services server

  Unable to connect to the web services server.  It is a common error that you might see if you try to enable web services.  If you receive this message, try the following steps.

  For Officejet printers

  1. open the internet browser type printer IP address.

  2 should bring you to the status of the printer page.

  3. Select the tab network at the top.

  4. left side select IPv4 under wireless.

  5. under DNS address Configuration select manual DNS server.

  6. for favorite enter 8.8.8.8

  7. for alternate enter 8.8.4.4

  8. Select apply. You can get a warning saying that this could break the connection which is very good.

  9. turn the printer off for about 30 seconds and then try to enable web services.

  For Photosmart printers

  1. Enter the printer's IP address in a browser.

  2 Select the network at the top of the page.

  3. on the left, select network.

  4. Select Network (IP) address

  5. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  6. Select apply you could get a fair warning select OK

  I hope this helps!

• Unable to connect to the web proxy/services

  Unable to connect to the web proxy/services used for officejet pro 8600 as well as using verizon fios actiontec router.  I tried wireless and ethernet.  Connectivity seems good.

  Resolved.  Port forwarding blocked by another application of verizonwebcamera problem.

• Unable to connect to the Web sites security and microsoft, but internet is not working properly

  Can anyone help?
  Now, this is getting very frustrating.
  I can connect to the internet and browse most Web sites. My email works fine but I can't connect to websites www.microsoft , Norton is 'unable to connect to the Live Update server, check the internet connection' and my media center can't find my internet connection.
  What is going on?
  I have a subscription to Norton who can't find any problems. I also downloaded onecare and trojan remover, returning with a clean report.
  Please help before I go out what remains of my hair.
  What about Frank

  Hello

  You can access Microsoft.com, McAffee.com, Symatec.com? Thinking you have a conficker.

  Check with this site
  http://www.confickerworkinggroup.org/infection_test/cfeyechart.html

  Alert on the Win32/conficker virus
  http://support.Microsoft.com/kb/962007

  Protect yourself from Conficker
  http://www.Microsoft.com/security/worms/Conficker.aspx

  How to remove the worm Downadup Conficker (Uninstall Instructions)
  http://www.bleepingcomputer.com/virus-removal/remove-Downadup-Conficker

  How to manually remove the Conficker worm
  http://www.411-spyware.com/Conficker-worm-removal#how-to-remove

  BDTool to remove
  http://www.bdtools.NET/

  -----------------------------------------------

  Run the malicious Microsoft removal tool, scan with Malwarebytes, Prevx to be sure you know all the
  malware involved and if necessary use UnHackMe.

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows Update - if necessary, you can download it here.

  Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
  (Then run MRT as shown above.)

  Malicious removal tool from Microsoft
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Malwarebytes - a scanner at the request - update on the updates tab and run whenever you think malware.
  http://www.Malwarebytes.org/

  Here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  also install Prevx to be sure that it is all gone.

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
  a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
  http://www.prevx.com/

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  --------------------------------------------

  Also do to the General corruption of cleaning.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------

  Run Malwarebytes when you can.

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security - reset all Zones by default level - apply / OK

  Close IE

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
  are bad, but some can cause your question. (Toolbars are BHO)
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Don't forget to do:

  Logon as administrator

  Start - type in the search box-> COMMAND - find on the list above - CLICK RIGHT - RUN AS ADMIN

  Enter each of these one at a time and press ENTER after each

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  Reset
  ------------------------------------------------------

  Here are a few rootkits if it were a question:

  SpyDLL Remover - free
  http://securityxploded.com/spydllremover.php

  Advanced Windows Service Manager
  http://securityxploded.com/winservicemanager.php

  Run the Rootkit Revealer - free
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb897445.aspx

  UnHackme - trial
  http://www.Greatis.com/UnHackMe/

  This shows how to use UnHackme and includes a link to version 2.5 – use it as a guideline and current
  available as version above is 5.5
  http://safecomputing.umn.edu/guides/scan_unhackme.html

  IceSword - free
  http://www.AntiRootkit.com/software/IceSword.htm
  Instructions and pictorial
  http://securityxploded.com/IceSword.php
  Tutorial for use of IceSword
  http://translate.Google.com/translate?hl=en&SL=zh-CN&u=http://soft.zol.com.CN/2004/0803/145163.shtml&prev=/search%3Fq%3Dicesword%26hl%3Den%26lr%3D

  Revo Uninstaller - free
  http://www.revouninstaller.com/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Unable to connect to the web.

  I have an Inspiron One 2305. Yesterday morning, everything was fine. Before noon I couldn't connect to the web. The network connection shows that I am connected. I always get an error "unable to connect to the page. I ran anti-virus and malware. Still nothing. Do a system restore I can connect on a single page. Try to leave this page and I get the same error. Can someone give me an idea?

  At this point you can repair or reinstall Win 7. Make sure that all of your personal files are stored on a medium firstexternally.

  To do a repair, you will need your reinstall Dell Win 7 drive. Start with a hard disk check

  • Click Start > run
  • Type: chkdsk c: /f
  • Click OK
  • Accept offer to run chkdsk at the next startup, and then restart. CHKDSK runs before Windows loads. Be patient as this can take some time, depending on the size of your hard drive.

  Unlikely that chkdsk will solve the network problem, but check it anyway...

  Then run a check of Windows system (CFS) files:

  • Click Start > run
  • Type: sfc/scannow
  • Click OK
  • Insert the Dell Windows reinstallation disc, if/when requested
  • Restart when done
  • Check again networking

  If this does not help, make sure that your files are backed up! Restart, and then press F8 before Windows loads. Look for the option of repair that may be on an advanced options menu. Follow the prompts. See if that solves network problems. And don't forget to visit the Windows Update site and reinstall all updates that are missing after the repair.

• Laptop has virus and still unable to connect to the Web site after his withdrawal.

  Original title: laptop cannot connect to router

  my daughter portable computer had bankerfoxa virus I think that I got rid of but she still can't connect on the website I want to download microsoft security essential on his cell phone how if I can not connect? pls help

  Hi trinidadg,.

  Also try the following steps, you have a problem connecting to the Web sites.

  Try to do a System Restore to an earlier date when your computer was working well and try to run a scan for malware removal.

  Try to reset the Proxy settings to connect to the internet, as some malware enable proxy settings that block your ability to browse Internet sites.

  To reset the Proxy settings:

  Click Start-> in "search programs and files" type CMD-> in the programs in the list right click CMD and click 'run as administrator '.

  In the command prompt, type the following and press ENTER:

  NETSH WINHTTP RESET PROXY

  Restart the computer

  Touhami

• Unable to connect to the web interface TCS

  Hello, I'm having a problem with a TC who left the factory of S5.3 current version. I can RDP into the Windows operating system without problem and access the web page of the OS on the port 8098 management no problem, but if I try to connect to the web application interface I get a name of user and password error.  any IDE on what is causing the problem?  the server was running fine until after a reboot.  Thank you!

  Hi Patrick, http:///tcs/#page:login&rescue:true method is used for the local administrator to log in if for some reason any when LDAP authentication is configured on TCS and local users cannot connect.

  ARO

  Mahesh Adithiyha

• Unable to connect to the Web Client

  Hello

  It is impossible to connect to the Web Client. They receive the following error message:

  Error RSL # 29
  Error 2046

  We use vSphere 5.0 U3.
  

  Hello

  If please try kb article below and choose the right answer if it solves your problem.

  VMware KB: VSphere 5.0 Web Client does not load and displays the error message: Error # 2046 29 with RSL

  Thank you

  RAM

• Unable to connect to the NAS network via a wired connection?

  Hi all

  I have 2 network NAS. They are both a Bay D-Link ShareCenter 2. One is full of media I use for streaming and the other is used to keep backups of my computers and some software. Both of the NAS are configured in RAID mirror. They both worked fine when I got them almost a year ago, they are mapped to letters pilot Y and Z. 2 days when I logged my office a popup notification came to say.
  "cannot reconnect to all network drives, click here to check the status of your network drives."
  so I checked it status and he said they were offline. I restarted my computer and both the NAS, but it made no difference. Then I tried to disconnect the drives, but when I try to reconnect to them I get this error;
  "Windows cannot access \\192.168.0.32\Volume_1\Joe, check the spelling of the name. Otherwise, there could be a problem with your network. In an attempt to identify and solve network problems, click on diagnose. »
  When I click to diagnose it is unable to find a default.
  The next thing I did was disable my Ethernet card and connect to my network with my WiFi adapter. Then I tried to re - map the NAS is connected via the wireless. This time he allowed me to map them and they seem to work as usual via the wireless connection, but it is rather slow on the wireless.
  Then I disconnected my WiFi connection and reactivated my Ethernet card. When I tried to open the NAS I get this error message;

  "An error occurred while reconnecting Z: to \\192.168.0.32\Volume_1\Joe, Microsoft Windows network: the local device name is already in use." This connection has not been restored. »

  A friend told me that this error was because the drive letter is used by a USB storage device or remembered from a previous session, and to remedy, I should run these 2 commands CMD;
  NET use * / Delete Yes
  NET use / persistent: no
  After you run the two orders, nothing has been changed still the same problem. I also I have no USB storage device so it may be that.
  The next thing I tried was to ping both the NAS, I did this on Ethernet and WiFi connections, and both times I return a normal response both to the NAS.
  I defrosted then to restore an image from my Office I made around a week ago and I know that I don't have this problem at the time. The image I did was with Acronis. When I started on the CD of Acronis support, I discovered that Acronis software could connect both the NAS on my desktop Ethernet. After restoring I still have the same problem.
  Now, there's 1 thing I noticed, my laptop can still connect to both WiFi and Ethernet NAS with all the problems. I also have an android phone, and who can connect both of the NAS via a WiFi connection.
  1 last thing you to know is I can always get to the configuration of the NAS so pages I visit it local address in a web browser. I also ran a factory reset both the NAS and then re-applied my own settings. This does not solve the problem, and more that turning March my routers.
  Please can someone help me solve this problem. I'm running a Windows 8 Pro 64 Bit operating system. If you need more information on my system spec or how I have my setup of home network please let me know.
  Thank you Joe.

  This problem has now been fixed.

  For some reason any my AVG firewall had defrosted on its own to block access to the features as well as to define its self to disable the file and printer sharing of files on the NAS share.
  So a small trick to my firewall and everything works as it should.
  Thank you Joe.

• Unable to connect to the Web site of 'report a problem '.

  I'm having a strange problem signing on the Web page 'Report a problem' in order to report a problem with an application that I downloaded via the iTunes store. I went to purchase in the iTunes store on my computer, click report a problem for the application in the order and he took me to a Web page called 'Report a problem' and asked me to connect.  However, I enter my information and click on connect, but the page just refreshes and doesn't connect. I know that my sign in information is correct (in addition to using it in iTunes, I just used to login here to post this question) and I came many times to just in case there was a typo in with my password.  I tried a longer password and it gave me the error "your AppleID or your password was entered incorrectly" so he is grateful to my info... I tried to clear cookies and cache from my browser (Chrome).  I also tried to use Internet Explorer and Edge to connect, but both had the same problem.  I couldn't even find a way to contact Apple on this specific problem... their support menus not occurred for problems of website that I could find at least (if someone could point me to that, I can try that as well).

  I had no problem connecting to https://reportaproblem.apple.com/ earlier. A temporary glitch perhaps?

  TT2

• Unable to connect to the Web by HTTP site after viewing once it with HTTPS.

  If I find a site with SSL (https). If later, I need to use it without ssl (http protocol) I can't, I am forced to use https. If you must know why it's necessary, it's because a Web site "https://example.com" ssl certificates configured properly, then that another site which is a subdomain "http://mysubdomain.example.com" didn't put certificates in place because it is hosted elsewhere. So when I try to connect to "mysubdomain.example.com" firefox forces me to use the https protocol, how the site does not load because it cannot offer me a page SSL version. The only solution I found is to delete all the temporary data of my browser and restart the browser. How I can use "http://mysubdomain.example.com", but if I ever go to "httpS://example.com", I can use only the subdomain because I am again forced to use the httpS Protocol.
  Is it possible I can stop this behavior?

  It works for me.
  https://addons.Mozilla.org/en-us/Firefox/addon/enforce-encryption/

• Unable to connect to the Web site

  I can get www.calphalon.com to load but am unable to connect. When I created the account, calphalon did exactly the same thing ebay-t - it does not recognize the security code even if it is correct. I did exactly what I do on Ebay when I ask a question to a seller - I use Internet Explorer. You have created calphalon account no problem and am able to sign in and out of my account without any problem with IE, but when I switch back to FF (updated 22), this is a go. With FF, the sign of the popup box is much too small and is completely empty. When I go to the tab of the client service to register a product (this is why I am on the site), I filled up on the sign in info on the page and the kickoff, nothing happens. It's as if I never hit the Send button. It does not seem to convey anything at all. I have signed up for newsletters, but cannot access my account on ff so it seems I'm going w/IE when I get on this site.

  Hello

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

  Thank you.

• Unable to connect to the Web Services Proxy/unused (a HP 7500 JO)

  Hello

  Here's the situation:

  Previous installer:

  .  I have connected my 7500 for the corporate network (IP = 172... series)

  .  registered the product with ePrintCenter

  .  used a PC under Windows to print (and scan) with the printer

  .  web proxy entry "webproxy.phila.gov".

  .  However, because homeland security rules, I could never work, so I just let it go

  Current situation

  .  has taken the home printer and set up on my home network, i.e.,.

  -using the 192.168.xx.xx series

  -Router broadband Netgear ' G' (1 years) set up at the 192.168.xx.254

  -SSID & encryption assigned

  -printer, the value 192.168.xx.155 (static IP address, the subnet and the gateway assigned as well)

  -My DNS is identical to the bridge and it works fine for all the internet access to this day

  -with the help of a PC and a Macbook Air to print and scan and everything works fine

  .  HOWEVER,.

  -Initially, 'web services' were active (carried over from when I was on the company neetwork?)

  ..  Are looking for, found and downloaded updates

  -When I went to hp.com ePrintCenter he showed the product as 'registered '.

  ..  He would'nt I would like to connect (with a name and a password I had used previously), or create a new account

  ..  I never remember getting an email address of the printer

  ..  and I had never been able to send anything to the printer to print because of my problem of network security

  -Yes, after trying all sorts of things, I:

  ..  I tried to get another email without success

  ..  tried to re - enable web services, but he said I need to 'proxy', and I discovered that he had always "webproxy.phila.gov."

  ..  I have reset the values by default web services and network values

  ..  I put the static IP address return address in (i.e., printer, subnet and gateway (it has nowhere to put in a DNS one))

  ..  printing and scanning to 192.168.xx.155 works fine

  ..  From my iPad AirPrint works very well

  .  BUT, I still can not online and therefore web server, web services are not enabled, therefore not ePrint

  -everytime I try, it says it needs a proxy

  - but I don't have a proxy installed on my internal home network bit

  -Comcast/Xfinity, my ISP, do not use a proxy

  So, I'm dead in the water.  I can't figure out how to get the web services enabled; I do not use a proxy, so I don't know how to go beyond this issue. How to regenerate address of the printer; and so, how do I connect an account on the ePrintCenter (or get them to send me my old account information).  I'm dead in the water and cannot use a feature most of my printer that I desperately want to be put in place and functional.

  Any help would be greatly appreciated!

  Tommy

  Problem solved, but I don't know exactly how I did it. However, I went back in and let the printer assign the IP address. Then I turned the printer off and on again. Last I kept pressing the button "Printer e-mail address", who has repeatedly failed, but then finally went through and print the 'printer' page, I quickly used to connect to the ePrintCenter and put everything in place.
  
  Now it's working.

• Linksys spa3102, unable to connect to the web-based utility.

  I have a problem... try to configure my spa3102 voip router, I can't connect you to the basic utility web (192.168.0.1/admin/advanced) page that he asked me to in the installation guide.

  a reapears of error "404-File not found" every time.

  Help, please

  first of all, make sure that your computer is connected to the LAN port on the back of the SPA3102 - then, click Start > run > type cmd > click OK > type ipconfig > hit Enter - glance to the DEFAULT GATEWAY - use to access the web interface of the SPA3102

  ex. If the default gateway as 192.168.1.1 type http://192.168.1.1 in the address bar of your IE - you can then click admin on the upper right of the screen and then click on advanced, also on the upper right of the screen

  * Sometimes the IP address of SPa3102 changes to a different address, especially if the device when you connect the WAN port has the same IP address which is 192.168.0.1

• NAS200: Unable to connect to the Web Interface

  Just set up my new NAS200.  I could install two (2-1 TB disks, RAID1) disks and set the IP address.  However, I can not connect in the administration area of the drive to set up users, shared directories, etc..  The doc on the CD has no value.

  When I run the initial Setup, I wonder for a pawword.  I enter the password that I entered in initial Setup, and I get.  However, this leaves me not do anything other that configure stuff of basic training.

  Someone at - it suggestions?

  Thank you.

  mechanism

  I was able to eventually get through the web interface.  It turns out that the system was not ready yet.  I have 2 1 TB drives in a RAID-1 configuration, and it took the best part of 2 days to get into shape.

  Once I was, I updated the firmware, and things seem to be working very well now.

  mechanism