Unable to connect to the wireless router

Similar Questions

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• Unable to connect to the wireless router. No ip address

  Recently, I plugged a Linksys E2000 router to connect two computers for internet access. Computer has access. 2nd computer cannot obtain an ip address. using windows xp sp 3. Technical support was no help.

  Hello

  As a first step put the computer near the router and start with the security off the coast.
  When it works, take it back to the final spot. If it stops then working, then you have a problem of distance.

  In general

  My wireless is not working - http://www.ezlan.net/wireless.html

  Basic wireless configuration - http://www.ezlan.net/Wireless_Config.html

  Wireless Security - http://www.ezlan.net/Wireless_Security.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• see the ssid but unable to connect to the wireless router

  I just installed a WRT160N router, I can see the ssid of the network wireless networks but cannot establish a connection with my laptop windows xp or my wify active blackberry...  Could I connect my mac laptop son with no issues... of ideas?

  Thanks for the suggestions, none of them had however.  The solution was to allow the width of the channel must be set to Auto 20 or 40 mhz, selecting only 20 mhz or individually selecting the 40 mhz would not so much my son computer macbook laptop and my IBM thinkpad to connect. But the default configuration which is set would not work. From the manual - yes I have finally checked it...  «Channel width Select Auto if you want that the router to automatically determine the width of the channel proper (20 MHz or 40 MHz) to use, or select 20 MHz only (default) If you want the router to operate Wireless-B and Wireless-G mode only.» For optimal performance, Auto is recommended. »

• HP photosmart 5520 cannot connect to the wireless router

  The printer has worked I went on holiday, and now it will not work. I have run the wireless network test, and it says "hp printer is unable to connect to your wireless router.  The wireless router is connected and works fine.  My hp wireless computer (windows 7) works very well.

  The structural 'found ssid network name' report, said down

  But "current configuration" has shown the SSID

  can anyone offer a fix?

  Help

  colleenmercy

  Hi colleenmercy,

  In the network menu, select default network.  This reset the current network settings and will help you reconnect the printer to the network.  You can use the Wireless Setup Wizard or reinstall the HP software to reconnect.

• I received a message on my laptop computer that says not able to connect to the wireless router.

  I received a message on my laptop that says could not connect to the wireless router and it make reference to section of the knowledge base Microsoft 87112 for more information.

  I think you have transcribed the number incorrectly.  I think that the article you want is this one: http://support.microsoft.com/kb/871122

• Unable to connect to the wireless network, error message "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.

  Original title: Unable to connect to the wireless network

  Unable to connect to the network wireless Toshiba Satellite A105 PC running Windows 7.  "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.  Works with Windows XP SP2, IE 8.00.6001.18702 file, I think that Version 3.  It has been installed on a disk provided by Microsoft after that old installation became corrupt (in the sense of Microsoft technical support.)  Before that, wireless network worked well.   (So unable to connect to the Internet for updates.)   Have tried to change the other settings and different messages acquired when it SHOWS that I am connected but cannot connect because of something to do with the certificate.  I don't remember what I did to try to solve this problem in the last days.

  I should add that I have tried the solutions of the previous forum on this topic, and none worked.

  Hi Marilynnla,

  Sorry to hear about the bad experience you encounter. Lets see if the network problem can somehow be archived.

  Read this article and follow the steps. Lets see if it helps in any way.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2 (Works for Windows XP SP3 as well)

• Satellite C660-1NJ - unable to connect to the wireless network

  Hi guys

  I got a 1nj c660 and I have a wireless connection to a Fritzbox 7170.

  Now, this morning, everything was fine and I connected wonderfully, but now I can't connect no settings have been changed I just stop and start as usual. I used configfree and it shows the network but if I try to connect it says unable to connect to the network. I have Win7 home basic OS.

  I uninstalled the wireless network card and reinstalled, updated the drivers but nothing works, I still get the same error.

  Can someone help will appreciate it greatly!

  Hello

  Are you able to connect to open WLan?
  I mean you can try to disable security options in your Fritzbox and might test whether you are able to connect without the WEP, WPA or other safety standards.
  Of course, you should only done for testing purposes

  If this box works, then it means that the security of your router settings were not consistent with the settings of the Wlan card.

• Satellite Pro 6100 - unable to connect to the WLAN router

  Hello

  I brought a 2nd hand Satellite Pro, model version SP6100 (PS610E-029ZV-EN), P4 1.7 Ghz, 512 MB, 30 GB, with Windows 2000 Pro loaded.

  I can't connect to my wireless router. The switch is in the correct position.

  I want to change to XP using the key provided with the new laptop (dual OS) however I can't reformat using a XP disc at the start up or if I use the recovery cd (start with holding C and let go when he works up) it starts but displays 'specification drive not valid' three times and charges Win2000.

  Can someone advise how (or if!) Can I reformat I want?

  Any help will be greatly appreciated.
  See you soon.

  Are you sure that the wireless network adapter has been installed in the laptop?
  Check in Device Manager

  On some series WLan is optional. This means that the WLan card is not installed, but it is possible to install an and, consequently, the laptop contains the WLan switch.

• no internet but not connected to the wireless router

  I have 400 SL with windows vista installed.
  Everything worked well for years, until a few days ago.
  It is the symptom, and what I've done:
  1. the laptop CAN connect to the wireless network, no problem, very strong, just signal has no internet.
  cannot ping google.ca.
  In network and sharing Center:
  Computer---> network---> Internet
  ^                   ^
  |                     |
  Red Cross OK
  2. all other devices (iphone, ipad, other laptops) can connect to the network and internet.
  3 did a system restore on the eve of this stoppped working. always the same.
  4A bought a wireless adapter, always the same. but it works fine on the other laptop
  5 tried to set a static IP, subnet mask, gateway, still the same problem.
  6. any other device can ping each other with the exception of this laptop...
  7. the seller cordless tool is uninstalled (Lenovo connection management tool)
  8 rebooted a million times between all the steps
  9 safe mode with network has the same problem.
  10 tried to use other wireless, still the same problem...
  need help...
  Thank you
  -Virginia

  Hi Virginia,

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the problem, I understand that you can not connect to a wireless network on windows vista computer.

  I appreciate your efforts on this issue, however no need for you to worry we are here to help and guide you in the right direction.

  Help me with the information below.

  -Don't you make changes on the computer before this problem?

  I suggest you to disable temporarily security software and then check if you are able to connect.

  Method 1

  You can also temporarily disable the security software and check if it works.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: These steps may increase your security risk. These steps may also make the computer or the network more vulnerable to attack from malicious users or malicious software such as viruses. We recommend the process that this article describes to enable programs to operate as they are designed for, or to implement specific program features. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this process in your particular environment. If you decide to implement this process, take additional measures to protect the system. We recommend that you use this process only if you really need this process.

  Method 2

  Reset the router and see if that helps.

  Note: to help you reset the router, you can consult the manual that came with the router or the router contact manufacturer.

  You can see this help article.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Laptop fails to automatically connect to the wireless router.

  Original title: re automatic updates for Windows Vista

  My wife & I have laptops running Windows Vista in our House. Recently, his cell phone fails to connect to our wireless router automatically. To connect, it must get the computer to automatically get new IP settings for the network adapter. However, she must do it several times to make a connection & must be done each time it connects. My laptop is not the problem. His only started to do recently. What can we do to make his newspaper from the laptop to the internet automatically without problems?

  Hello

  Follow the steps mentioned below and check to see if they help.

  Step 1:

  Card drivers update of your network.

  Step 2:

  In addition, you can uninstall and reinstall the Device Manager wireless network card to be a safer side.

  To uninstall the wireless device manager,

  a. Click Start, type device manager in the search box of start and press ENTER.

  b. Locate the network adapters and expand the same.

  c. Select the wireless connection, right click and choose uninstall.

  d. restart the computer, if prompted.

  Pilots should settle automatically after the computer restarts.

  Now you can install the latest wireless drivers and check if this solves the problem.

• I bought a Sony BDP - S185 connect Netflix Blu - ray player. I can't connect to the wireless router. Why?

  I just bought the blu - ray BDP S-185 drive so that I can access the internet (netflixetc.) on my new samsung tv. I tried to connect to my wireless router, but repeat me my connection type iswired and the connection has failed. Can I connect this player to a wireless router or should it be connected to the router? Difficult because the router is in the basement and the television on the third floor. Can I use the separator on phonejack (existing in the 3rd and.) and connect the two phone and blu ray player or do I need a netgear typedevice to connect this player? Thank you in anvance understand help. Sorry, it's so rambled butI am very confused here!

  Hi Robert,.

  Welcome to the community of Sony!

  This Blu - ray player is the BIV (Internet Video base) base model and does not support the wireless Internet connection. I suggest that you use the Ethernet LAN cable to connect the player to your router/modem.

  Thank you for your message.

• Unable to connect to the wireless network WPA2 in Windows 7 with Dell E6400

  Hello

  I've spent almost a week to find the following problem with one of my laptops:
  Laptop Dell Latitude E6400
  CPU Intel Core 2 Duo T9400 2.53 GHz
  Memory 4 GB
  OS Windows 7 SP1 32 bit Home Premium
  Card WiFi Dell Wireless 1397 WLAN Mini Card
  Intel 82567LM Gigabit Network Connection Ethernet card

  With the wireless configuration (Ethernet is unplugged), my E6400 sees the Motorola SBG 6580 wifi router using WPA2, but when I try to connect to this router (with WPA2 password) I got the error message:
  Windows could not connect to myrouter.

  I've updated all the drivers with the latest version and I still have the same error message.

  I have another laptop Dell E4300 under Windows 7 SP1 32 bit Home Premium and I can connect to the Motorola router without problems.

  Do you have ideas of how to solve this problem?

  Thank you

  I had this problem with my new Dell 1545 & wireless 1397 card, but it was some time ago. The utility Dell WiFi was, it turned out, interfere with the management of the windows of the WiFi card. There was also a problem of compatibility with versions of driver and I had to keep the driver to the version Windows offered two years ago. You can read about it at low signal wireless Dell Inspiron 1564 laptop 1397 WLAN Mini card , but do not forget that it was some time ago, it's with another model of Dell & that no router was involved.

  You can also try asking Dell support, but I never had any help from them at all, despite the request.