Unable to open driver ACPI ATK0100 Kernel Mode - Tecra A9

Similar Questions

• On Satellite A200 error message: could not open the ACPI ATK0100 Kernel Mode driver

  Hello

  I have laptop Satellite A200
  When I run the windows (vista) I get the following error: * 'Can t open ACPI ATK0100 Kernel Mode Driver.*'!
  I installed all the drivers and the error remains.
  I installed all the drivers on the Toshiba site, but the problem persists.
  The Device Manager shows me that each device is working properly.

  Someone at - it a solution?

  Thank you

  ACPI is the installation of your Windows operating system power management. If this fails you may need to run a recovery system on your computer. You can do this with the hidden partition on your hard drive, but this will erase all data on your machine. If this does not resolve the problem, you may consider making your hard drive, checked bad sectors, as this may have failed.

  I hope this helps. :)

• Satellite L300D - cannot open the ACPI ATK0100 kernel mode driver

  Hello!

  Please, I have a big problem.
  I used recovery dvd to re install vista basic.
  Since starting I have this message:

  * Cannot open ACPI ATK0100 kernel mode driver *.

  An unknown device is detected in my windows and there is no driver to install. I have no wifi detected.
  Manual installation of the driver atheros do not work!

  Please help me!

  What can I do?

  Hello!

  I never heard of this issue, but try to update the BIOS as Akuma said. It s worth a try! On the Toshiba site, you can search for an update of the BIOS:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  In the worst cases, you should try to reinstall Windows using the Toshiba recovery disc.

  Good bye

• SL500 - cannot open the ACPI ATK0100 Kernel Mode driver

  I installed Windows 7 (64-bit) and some of the drivers of Lenovo.

  Now, I get this message every time you start.

  Any ideas?

  uninstall the driver and the custom messege come, lenovo is not technically support windows 7, all other work drivers on my SL500 outside this driver, became the messege too, now I don't have after that I uninstalled it

• "Cannot Open ACPI ATK0100 Kernel Mode Driver" on G560

  Hello world.

  I have downgraded my Windows7, Windows XP machine and after reboot appear this pop-up message: "CAN Open ACPI ATK0100 Kernel Mode Driver. I was reading another post for the same problem but I don't know what I can use these instructions for my laptop model G560.

  Help, please!

  Thank you

  Try re - install

• Satellite Pro L300 shows ACPI ATK0100 Kernel Mode Driver error

  I have a Satellite Pro L300 with Windows Vista and it has been fickle to say the least, making me restart the system several times.
  The last two times she since continued to come up with an error message saying "cannot open ACPI ATK0100 Kernel Mode Driver", and I understand that it is perhaps what is originally that there problems later.

  I tried updating the BIOS, reinstall the drivers and, seeking answers and, of course, reinstall the whole system, but I still get this message every time I turn on my laptop and I really don't want that it gives me the blue screen of death again - please help me!

  Thank you.

  Stand by.

  You ve done clean install of Vista with initial recovery DVDs and you get this error in any case (no additional software is installed)?

• Satellite U400 (PSU44E) - ACPI ATK0100 Kernel Mode Driver missing

  Satellite U400-17V (PSU44E)

  I received my upgrade of Windows 7 at Toshiba with the included DVD upgrade. I did everything exactly what is said in the booklet.

  After completing the upgrade process and after turning on the laptop I got the message saying:
  Can not find an ACPI ATK0100 Kernel Mode driver

  What should I do?

  Best regards
  Tan Tunc

  Hello

  I started a thread on the same subject:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=126340

  So for me it sounds like this, you should try to reinstall Windows again. After that, the problem should be solved.

  Search with Google, you can find enough discussion about it. Reinstalling Windows can solve this problem.

• Satellite A100-599 - ACPI ATK0100 kernel at startup mode driver error

  I get an error msg (ACPI ATK0100 kernel mode driver error) at startup.
  I use Vista as my OS.

  Please advise as to how to fix this.

  Hello

  Hmm the message says something about ACPI
  As far as I know the ACPI is the installation of the power management of the Windows operating system. If you get this error message then, something must be wrong with the power management

  Have you tried to recover the laptop using the Toshiba disk?

• Display driver hangs on the computer and the error message "display driver NVIDIA Windows Kernel Mode Driver Version 306.97 has stopped working and recovered."

  Original title: NVIDIA Windows Kernel Mode Driver Version 306.97 display driver has stopped working and recovered.

  Hiya,

  I have recently installed Windows 8 Pro, installed all of my usual applications etc..
  The problem I've encountered is maintaining display driver crashing. Or have waiting periods. The exact error message reads;
  "Display driver NVIDIA Windows Kernel Mode Driver Version 306.97 has stopped working and recovered."
  Until now it expires randomly even when the computer is idle, and more frequently when I watch videos online. Also, watch a clip full screen on some sites like YouTube is ok, but on others, it is very laggy (updated maybe once per second the image) and the sound is out of sync.
  I can't find a way to properly uninstall the graphics driver.

  At least yours is working semi... I have the GTS 450 (uses the same drivers) and the mine does not at all... Stuck with the regular game pilot integrated ATM and can not all games... Microsoft told me to wait a few weeks and for the reminder and Nvida said 10 ways to uninstall and reinstall the drivers for same. Hope someone with to get a fix for this soon.

  Hi guys,.
  Looks like this isn't just me.
  Just an update, that I can not confirm it as a solution, but I have not encountered any problem (a little screenlag aside) since the installation of the drivers beta. For me, the beta version of the driver is 310.33, R130. The only other change to my system updates Adobe Flash version packaged with Google Chrome to 11.4.31X to 11.4.402 to eliminate serious problems when you watch the video in full screen.
  Information system;
  Operating system: Windows 8 Build Pro with Media Center 64-bit, 9200
  CPU: AMD FX-8150 eight physical cores
  GPU: ASUS NVIDIA GeForce GTX 560 TI
  Main hard drive: OCZ Vertex 3 120 GB
  It may be useful
  Edit: Still not falling down, 11/02/12, 4 days
  
  
  New edition;
  
  
  If you still receive the error message, try the following steps;
  Has. try to perform a clean installation of the driver.
  Download the latest drivers for your graphics card. Run the downloaded file, and select "Custom Installation". In the next screen, you will see a checkbox or similar labeled "Clean Install".
       
  
  You can do so by visiting nVidia Driver Downloads (www.nvidia.com/Drivers). Automatically detect the right driver or download using the form. The best way in my opinion is to use the GeForce experience, who will do anything for you in two clicks and a reboot.
  B. close all other programs
  It is possible that the error was caused by too many programs that need to use the resources provided by the graphics card/chip. It is also possible that a certain program caused a conflict that pilots crashed.
  You can try closing some currently open programs one by one and see if the error persists, or restart your system with disabled startup programs and allow them one by one to find the culprit. If the error is too persistent to do the above, it would be easier to start in safe mode option.
  More information can be found below
  http://support.Microsoft.com/kb/2665946/en-us

• driver NVIDIA windows kernel mode 285.62 unresponsive

  Momentarily, screen off, then recovers. Message "Display driver driver NVIDIA Windows Kernel Mode Version 285.62 unresponsive & has successfully recovered".

  Windows 7 Edition Home Premium.

  Any suggestions?

  This is a problem experienced by many users and (surprise) No (proven to work for all or most users) solution/fix. A solution/fix may work for a person facing this problem; but maybe not for the other person.

  This issue is encountered by other people with the same version of the driver and is being discussed on the forums from Nvidia since December 2011. You can try many possible solutions mentioned.

• "display driver nvidia windows kernel mode driver version 310.64 not responding and has successfully recovered"

  I always get the following error message "display driver nvidia windows kernel mode driver version 310.64 stopped responding and has successfully recovered". It sometimes lets my screen refresh but often he kills to the video out all together and I have no choice but to hard restart my system. I did the thing to uninstall/reinstall Nvidia, Dell and Windows all with no success. I am running windows 7, graphics Nvidia Gforce GTS250 in a Dell XPS420. Any ideas out there are appreciated!

  Your Dell was origonally supplied with Vista, there is no win7 drivers available from Dell.

  All drivers obtained through windows Update are generic drivers.

  I also assume that its a Nvidia card you have purchased.

  Account these two elements that he may very well be an incompatibility with drivers problem, for which there is no resolution on the current hardware

• Display driver stopped responding and has recovered the display driver NVIDIA Windows Kernel Mode Driver

  Hey guys I have a problem that is really starting to stop a little worth. I recently bought this desktop computer and I had problems with the GPU drivers when I play some games. In the middle of my game, I am reduced to a minimum and maximized every 15 seconds and have the error "display driver stopped responding and recovered, NVIDIA Windows Kernel Mode Driver display driver." I tried SEVERAL solutions from different threads, and I still have this problem.

  Things I've tried:
  -Added a TdrDelay (8) in my regedit
  -Defining my CPU PhysX on my GPU instead of automatic selection
  -Install an older driver over the last.
  Specifications of the PC:
  -8 GB DDR2 RAM
  -Nvidia GeForce 9800 GT Galaxy
  -Power 500w S
  -Card mother ASUSTeK Computer Inc. M3N-HT DELUXE
  -Microsoft Windows 7 Ultimate 64-bit free multiprocessor-7601 Service Pack 1
  -AMD Athlon (TM) 64 X 2 Dual Core Processor 6000 +.

  Hi Vexin,

  Try the following steps to solve the problem.

  Step 1:

  I suggest you uninstall the device of the graphics card from the Device Manager.

  To open the device in Windows 7 Manager - check this link.

  Once uninstall you the graphics drivers in the Device Manager restart the computer.

  Step 2:

  Visit the manufacturer's website and download the latest drivers for the graphics card.

  Link to the manufacturer's Web site.

  http://www.GeForce.com/drivers

  I hope that helps!

• Qosmio X 500 and question NVIDIA Windows Kernel Mode Driver.

  Hello

  For some time my X 500 will 'freeze' then gives me a black screen before returning to "normal" with an error display window in the taskbar. The read error ".

  "* Display driver stopped responding and has recovered."
  "+ Display driver NVIDIA Windows Kernel Mode Driver, Version 259.12 stopped responding and has successfully recovered.

  Have run a diagnostic on the laptop and tried the NVIDIA drivers updated etc, but it continues to happen.

  Any ideas on the causes AND more to the point HOW to solve this problem?

  I post a screenshot of the error message but cannot find how this is done - if it is allowed?

  See you soon

  Frank

  Hello

  I guess that this is caused by the graphics chip, it is possible that caused graphics card driver problems related to bad entries in the registry or in the worst case the graphics chip could badly run.

  Also found this thread where the user that edbelgium seems solved problems with graph on X 500.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=64607

• Satellite A500 - NVDIDA Windows driver in kernel mode has stopped working

  I bought a brand new Satellite A500-1GL with a Geforce GT 330 M graphics card. Unfortunately, whenever I watch videos in full screen I get the following error.
  "Display Driver NVIDIA Windows Kernel Mode Driver Version 188.29 has stopped working and has recovered"

  The screen turns white and the sound terribly false. I have already uninstalled and reinstalled the Nvidia drivers. It seems that all A500-1GL models with faulty chipset on the motherboard. Toshiba must investigate this matter!

  Help, please

  Hello

  The videos you watch exactly? This happens with all the videos, for example Youtube, DVD, or only with specific files?

  I also GT330M graphics card in my phone but I can t notice any problem with him. I m using the version preinstalled Windows from Toshiba and the last driver display Toshiba official page.
  And you should try updating the BIOS

  Finally and most importantly, another user reported that he could solve the problem if Windows Aero is disabled:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=51367

  Check this box!

• I'm unable to open documents on my mac iCloud drive

  I'm having a problem where I am unable to open documents stored in iCloud drive on my MacBook Pro.  I already could solve this problem of disconnection and return in my iCloud desktop account.  This step doesn't work anymore.  When I try to open any file stored in iCloud, I get a message saying "the file _ could not be opened."

  Example: I opened the Pages.  When I try to open a file through this program, it will not be open.  If I try to open the file in the Finder, the same result happens.  This applies to the files of numbers and .pdf files.

  Hi mattfrompdc,

  Thank you for using communities Support from Apple!

  Looks like you are having some problems at the opening of documents stored in iCloud drive. If you do not already done, please go to iCloud.com and connect see if you are able to open the files there. If you are able to open the documents there, the next step would be to start the MacBook Pro in Mode safe and see if you can open documents from your iCloud drive it. A time tested, and then restart the MacBook Pro and try to access the iCloud drive as you normally would.

  See you soon!