Unable to start with a new graphics card

Similar Questions

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Does not start with the new graphics card

  Hello. I have a P7-1058uk Pavilion Cleveland-GL8 motherboard with integrated graphics.

  I bought a new monitor that has resolution 2560 x 1440, equal the integrated graphics card can face if tried to to level with a Gigabyte GT630 card.

  When I start, I have now the chance to the blue HP screen but not more details. If I start with F10 or ESC key, I get a black screen instead. Whatever it is, I am asked to press ESC to enter in the start, but by pressing on the button has no effect and the computer just hangs. There is a cycle repeated very quiet click that sounds like the disk drive HARD trying to start then stop

  If I remove the graphics card and connect the monitor to the integrated graphics card then all's well again (but limited to the resolution 1920 x 1080).

  Perhaps foolishly, I assumed it was a problem with the residual power (300W) and not enough punch power to run the HARD drive. But who, after having upgraded to 650W it makes no difference. I also tried to download the NVidia drivers but it won't let me install because I can't get the computer to work without the graphics card and Nvidia install it because it cannot detect the hardware.

  Any ideas/help would be appreciated.

  Andrew

  You can have one of these motherboards that are not happy with NVIDIA graphics cards.

  This may sound a little weird, but it happens.

  The other possibility is that you have damaged your home x - 16 PCI Express by installing a map requiring more that the installed power supply has been able to provide.

  Kind regards

  ERICO

• Qosmio G10 with the new graphics card and pcb - CD update tools do not work

  Hello world

  I hope you can help me. Before a few weeks, I received my Toshiba Qosmio G10 return of aid, because the laptop no longer works. So I get it back with a new graphics card and a new PCB. With my laptop I have a CD called the update tool CD and a sheet of instructions, where it says to start with this tool CD-Rom update after you have installed the Windows with the reovery CD.

  So I did, but when I know the update tool CD to put in and I start with it, the computer installs something, but after a short then it is a message that it is a different model and that I have to put a button to close Notepad. So I did it, but Windows does not start.

  Why is it so? I had done everything that has been said on the instruction sheet.

  Please help me

  Hello

  It will be interesting to find more information on this CD-Rom tool update. Are there tags Toshiba? Can you please write what is described here?

• HP Pavilion HPE: PC does not start at the top with a new graphics card installed

  I improved my diet to 600w and my new graphics card is a asus gtx strix 960

  My older gpu was a Geforce GT530.

  I've updated, drivers and BIOS of this HP Forum... and then I turned off my pc, took out the 530 and replaced by the 960. I start up the PC and it's me stuck on this screen. This photo is of online, that's exactly what mine looks like well. When I press "ESC to start menu", the screen goes black. the GPU and all good works. my version is v7.16

  

  only reason why I bought it was to play The Witcher 3...

  any help?

  calviiin wrote:
  

  Hmm. Looks like I won't get that. It's just another card that I purchase and its more expensive than the 960 gtx that I just bought.

  Thanks for the help.

  Don't, don't. It will be brick. They are also 2 completely different mobos. One choice is to buy a new motherboard or a new pc.

• Computer does not start with the new video card

  Hello

  I have hp pavilion 500-277cb and I love it, but it won't work with my new video card

  The video card is
  Sapphire ATI over-pants 2460

  I heard 6 beeps and I turned off safe and active start legacy. It does not beep, but it is not start either, just black screen.

  It seems to me to have the latest version of the bios and windows 8

  What can I do else?

  Thank you very much

  Best,

  Korhan

  Hi JM,

  Did you remove the Intel HD graphics drivers prior to installing the ATI graphics card?

  Your PC comes with one of the following built-in Intel graphics drivers:

  • Graphics Intel HD 4400 (GT2)

• HP pavilion p6226it: can I upgrade my pc with a new graphics card?

  Hi, I have a hp pavilion p6226it, I would like to know if the graphc 7750 HD card would go well on my old pc.

  matherboard: M2N78-(Violet6)

  Processor: AMD Athlon II X 4 620

  RAM: 6 GB

  Graphics card: HD 4650

  Same expert people told me that I could have problems because of my matherboard and bios (I've never updated), is this true?

  @antonmartino,

  Hi again.  Just below the section for memory you'll find.  What you can do is take existing specifications and the specifications of the motherboard and see what card maximum that you can put in the slot.  The only thing you want to look at is what is the power required by the new map you found and if the power supply has enough power to stay with her horse.  If you talk to any place of the computer with the specifications of this page, that I gave you, they can give you the best option.  What I do is take the listed specifications of the card and match the cards, in that you are looking to put.  Check to see if it's the same dwelling and look to see if they require the same requirement for voltage and they should work perfectly.

  I hope this helps.

  Thanks again for the post and have a great day.

  HP Pavilion p6226it Desktop PC product specifications

• Lenovo M91p desktop does not boot with the new graphics card (Blank don't screen no BIOS)

  Hi all

  I recently bought a Lenovo M91p thinkcenter Desktop as an upgrade to my old PC i3.

  Old Spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Intel DH55HC
  • Processor i3
  • Graphics HIS HD Radeon 7950
  • 8 GB RAM
  • HARD DRIVE 500 GB

  I transferred my HD supply and Power 500 GB old to new Lenovo desktop and everything starts very well.

  Then I installed 2 x 2 GB extra in the Lenovo M91p (which in fact 8GB) and updated the disk of 500 GB to 1 TB.

  So my new spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Lenovo Q67
  • I7 2600 3.4 Ghz CPU
  • 8 GB RAM
  • 1 to and 500 GB HARD drive

  Everything Booted fine. Then I tried to install my old graphics (HIS 7950 graphics Radeon HD card) card. I got was a blank screen, no beeps, no BIOS... Nothing.

  At first, I thought that my diet was not enough... So I tested a 750W power supply in the pc. Still nothing.

  Then I thought that the motherboards BIOS was outdated... Updated... Still nothing. I even tried to update the firmware of the graphics card. Nothing.

  The graphics card works because I tested it in my old machine and it worked 100%.

  However, I took my graphics card to my provider and he tests it on another of his pieces... Did not work there either.

  My PC BIOS is not supported for secure boot, in case anyone wants to know.

  I am out of ideas now... Anyone able to help?

  There is a white list of graphics cards that will recognize the BIOS. The 7950 HD is a map of 180w, well beyond what the power plant can provide (and case/sufficient cooling fans for) and not a single one is that Lenovo would provide support for the BIOS.

  Use the search engine above to see what cards other owners have used successfully in their M91p.

• HP PAVILION HPE h8-1192d: could not start after installing new graphics card

  I recently bought a Gigabyte GTX 750 Ti Black Edition to replace my old. But it will not start after installing on my h8-1192d, and stuck on the screen flash hp. Help, please!

  Hello

  NVIDIA GTX 7xx or 9xx series graphics cards will not work in your PC.  The BIOS in "chicago" mothererboard is not compatible with the video BIOS in the graphics card.  You will need to get an older card chart such as the one of the below listed OEM HP graphics cards. Depending on the graphics card, you may need to replace the power suplly.

  

• HP Pavilion p6-2469ea replace it with a new graphics card?

  Then after hours of stress online and planning on the upgrade of the case, power supply and a GTX 760, I fell on contradictory comments and other experiences of users during the installation of new cards in the PC.

  My PCI-E X 16 slot is a 2.0 then the card is 3.0, but they are retro-compatible, so all that means is I lost a few images, however, users have said HP lock their computers that are predefined and will prevent any installation of new parts that are not installed origanlly.

  I need to know if this is true, before giving up £300 + on equipment to upgrade this PC or to get rid of it and create one from scratch.

  If anyone can help I would appreciate it a lot.

  The motherboard is the blue/white MS-7778 Jasmine if this is useful, with card Nvidea geforce GT 620

  Ok.

  Indeed, it is stretchy. Be sure to check all system requirements of video card foresight to see if they require that you upgrade the PSU. Check the specifications of your PC to see how many Watts (RMS) power supply delivers. I just checked. It has only 300 Watts. It would be preferable to one with a little more grunt (@450 Watts or more) If your goal is to upgrade to a video card that has real power.

  More low end PC have no power supplies which are equipped with six and eight-pin PCIe power connectors. They are required for general public and higher end graphics cards.

  The video card on that question:

  Requirements

  At least a 350 Watt power supply.

  (Recommended minimum power supply + 12 volt current rating of 18 AMPS).

  Power total draw: 49 Watts

  Some versions of the video card, according to the vRAM installed consume more energy.

• Help with the new graphics card on old pc

  I have a dell dimension 3000 'ya I know sad' I would like to add a graphics card and a new soft power since the wife won't let me buy a new PC GRRRR

  I have a GeForce 6200 PCI 256 MB dcr2 it will work in this pc

  I also bought a power electric double w 480 SATAs is large enough to run the new card and the pc?

  Thank you

  You can add the 6200 PCI if you wish.  It does not require an upgrade of the power supply however.  It will work fine on your PSU 250 watts.  I have the 6200 circulating in a Dell with a 250W unit just to get the higher resolutions than the integrated graphic card has been able to provide in support of a monitor.

• With the new graphics card failure

  I tried to put a graphics card in my desire to 700-210xt, there graphocs of the motherboard and I need the output HDMI and DVI, which he did not.  I added an ASUS silent 210.  Power on or monitor the work and the computer beeps six times.  Monitor never works, not isolation, or duplicate, even if the computer doesn't seem to not be starting.

  Remove the graphics card returns the system operation.

  Suggestions?

  Hello

  See the HP document on the following link.

  http://support.HP.com/us-en/document/c03653200

  Kind regards

  DP - K

• Need help with the new graphics card

  So my trusty GTX 555 is finally dying after 4 years and 10 000 + hours so I looked in an upgrade and heard the GTX 960 would be a good upgrade for an Alienware x 51 R1. So I got a PNY GeForce GTX 960 Amazon and installed but when I turn on my system it passes to the BIOS screen and is there for about a minute and a half and it beeps every 30 seconds after the screen came. After the minute and a half or two then goes to a black screen and says the brand and model of graphics card in the upper left corner for about 5 seconds, then he sits on a black screen. I did something wrong?

  If necessary system specs:
  330W POWER SUPPLY
  Intel Core i7 2600
  8 GB RAM
  Windows 7

  Have you updated the BIOS?

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• (Redirected) upgrade my studio 9100 with the new graphics card and a more powerful power supply

  I have a studio 9100 with 525 usual w PSU. I need a processor amd or NVidia card and MI those watching amd r9 x 280 and 780 NVidia gtx need system in order to get a 750 w power supply. should I buy the card and the power supply through dell, or somewhere else?

  Hi michaelwilson73,

  Please repost this in the laptop computer forum for faster assistance.

  http://en.community.Dell.com/support-forums/laptop/