Unplugged cable error

Similar Questions

• Error 54 unplugged cable

  I have a quad port NI PCIe-8235 I use for UDP communication. We have UUT which has 4 ports UDP and can toggle the on command. Ideally, I would like to open a UDP connection and wait all incoming traffic. Instead, some of the cards receive an error 54.

  After much experimentation, I noticed that if the card was plugged in at any time, I get this error.

  If I disable and then enable the network adapter while it is unplugged, I got the error again.

  If I have the cable in and unplug, I don't get the error on any open UDP.

  Normally, I'd like to loop until I do not get the error. However, this error also appear to detect IP addresses wrong, I consider a valid error.

  My assumptions are:

  Miss me something stupid openly

  or

  These cards can enter a State that windows be forget that they are there, or does not allow connections. I hope that I can work around.

  or

  Not allowing a connection is valid, and plug/unplug the cable tips windows. Allowing me to cheat.

  It may also depend on whether you're ready DHCP; you could lose the IP address because of this. But yes, it looks like more than one Windows + behavior of ethernet cards.

• "Unplugged network error" appears frequently__

  Hello
  I use the function wireless of my modem to connect to internet for my laptop and an ethernet cable (rj 45) for my desktop computer for internet access.

  But my office frequently disconnects from the network saying "disconnected network error" and then connects again. This is repeated several times.

  I need to connect to the internet with the ethernet cable to my desktop and wireless for my laptop with no problems. Help, please

  Laptop, network - Realtek RTL8139/810 x Family NIC ethernet adapter

  Office - Interl (R) Pro/100 VE network adapter

  I use winxp

  Modem
  BoardID: 96338W
  Software version: 1132_061507 - 3.08 L. BSNL_02.
  Version of the bootloader (CFE): 1.0.37 - 8.7
  Firmware Version: WA3002G4 - 0021.01
  Hardware Version: 1.0 WA3002G4
  Model name: WA3002G4
  Wireless Driver Version: 3.131.35.6.cpe2.0a.s

  Hi hello123321

  First of all, try a different cable of good.

  Otherwise, http://www.ezlan.net/faq.html#unplugged

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Satellite Pro L10: PXE - E61 - Media test failure check cable error message

  I recently bought a laptop L10 without the hard drive, and whenever I try to start it with a hard disk newly installed, I get this message.
  PXE - E61: MEDIA TEST FAILURE CHECK CABLE
  PXE - MOF: EXIT PXE ROM
  OPERATING SYSTEM NOT FOUND.

  Someone can MAKE SENSE of IT AND ME the EXPLAIN, AND ALSO HOW can I GET the RECOVERY SOFTWARE I don't HAVE THE TOSHIBA RECOVERY CD BUT I don't HAVE THE CoA STICKER ON the laptop.

  IM DESPERATE PLESE HELP

  Hi Nash

  The PXE error occurs because the laptop tries to start first from the local network.
  You must enter the BIOS and change the order on HARD disk or a CD. I recommend that you set the LAN option at the end of the boot order.

  The recovery CD you can buy form the Toshiba service partner in your country.
  The number on the sticker is only an OEM key. You can not use it with a Windows operating system several.

• The fact to unplug cable adapter HBA on the ESXI host causing VI Client to hang

  We use HP DL380 G5 with the embedded HP version (ESX 3.5i U3 + latest patch)

  This server has all of the available features available (HA, DRS etc..) The server has 2 EMC QLogic 2340 HBA with the latest EMC firmware in it.

  If I look in the VCenter in a disk storage properties it shows me 4 available for SP on our SAN paths. (all MRU settings. we have SAN active/passive)

  Now, here's the problem we have:

  As soon as I unplug the fibrecable, the Vcenter must use another active path. It looks like this, the VM Machines are continue to operate, but only after a new analysis of the hba it also shows that the 2 paths are broken

  But when I close the VI Client and run it then the problems begin:

  • Machines of VM loses connections (rattling irregular and after awhile not available)

  • Customer VI freezes and does not

  In the end, I have reconnected the fibrecable (because each time I start the VI Client it crashes) all problems disappeared and everything works again.

  If I then take a look at the Machines-VM BSOD some are, some have the writeback failed

  Disconnect a fibrecable shall not give any disruption, that's why we have redundant HBA. But it does!

  Anyone have any suggestions?

  HBA QLogic VMkernel pilots understand firmware which (actually) hot-loaded on the HBA driver support.

  See http://communities.vmware.com/message/325181#325181

  So, don't bother with the HBA firmware level.

  See the latest "Fibre Channel SAN Configuration Guide.

  page 99: setting the time-out HBA to failover (value qlport_down_retry)

  Good luck.

• Laserjetpro m252dw: printer says network cable unplugged when plugged into a wall outlet

  My printer worked fine and all of a sudden, he is no longer prints and the display shows: "network cable unplugged".

  I turned off the printer, it is plugged. Does the same thing for the modem and the router. The problem is not resolved. Help, please

  Hi @Kajosil,

  Welcome to the Forums of HP Support!

  I understand that you are unable to print because of this "unplugged network cable" error message on your HP LaserJet Pro M252dw Color printer. I will definitely do my best to help you and don't forget to come back to this thread and mark "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  It seems that the printer does not have enough power to work properly, or there is a problem with the cable/port.

  • Please click here to update the firmware of the printer.

  Make sure that the ethernet cable is connected to the appropriate port on the back of the printer.
  See the section: 'Return product view' in the user manual for more information.

  • Have you tried another port on the router?
  • Have you tried another ethernet cable?
  • Check if the cable is damaged or deformed.

  If the problem persists, I would like to do a hard reset and electric drain to see if this will solve the problem.

  • To eliminate other causes, unplug the USB cable or telephone (fax) for the test so attached.
  1. Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  2. Press and hold the power button for about 15 seconds to drain any residual electric load and then release the power button.
  3. Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
  4. Make sure that the printer is connected directly to a wall outlet (do not use a bar or a surge protector).
  5. Try another outlet to power/room.
  6. Try a different compatible power cable.

  If the problem persists, I would try resetting the NVRAM. This will outline the printer back to the default settings. The network must be configured again. I can send you this information in a private message. In the forum next to your handle name simply click on the envelope to see.

  I hope this information is useful. Please reply to this message with the results. Good luck!

• Example: HP Laserjet 2840: HP Laserjet 2840 error 79

  The screen of the computer displays error 79.  It says restart the printer.  It does this automatically then comes up with the same error code.  It keeps on rebooting.  If I turn it off and then on it is just straight up, displays the code error and restarts again continuously.  Anyone know how to fix this?

  79 errors are usually caused by the corrupt works, usually remove some jobs are in your print queue clears the error on the printer.

  The fastest way to see if it's a job is to unplug cable USB or network printer and then power cycle the printer, if the printer gets ready status and then try to print internal test pages. If you print the internal test Pages is very probably a corrupt job.

  Quite often, it's a file downloaded from the internet and it will usually be a PDF file.

• HP Photosmart 7760 printer will not print, the error message in the queue

  I have Mac 10.6.8.   Printer (HP Photosmart 7760) has stopped working.  Reinstalled the drivers updated. Went through the steps including unplugging cables USB and all the other steps recommended by HP. When I press print, the document goes to the queue and and the error message is displayed. When I press the resume to print, nothing happens.

  We will restore the print system:

  -Sys Prefs, Print & Fax
  -Right (control) click inside the box that lists your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign + to add again. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• Satellite Pro A10 fails to start - IDE #0 ERROR

  On startup, I get the Toshiba start screen and there is a regular click from the HARD drive. After 20 to 30 seconds, I get:

  ERROR IDE #0

  then a pause, followed by the following codes of boot agent (Intel FE v4.1.09)

  PXE - E61: Media test failure, check cable of
  PXE - M0F: Exit Intel Boot Agent
  Insert system disk in drive.

  I have the unpleasant feeling that the HARD disk is dead. I can replace it if necessary, but is it possible to extract the files from it before going so far?

  That is a clear symptom of a HARD disk failure.
  The + IDE #0 + error means that the BIOS didn't recognize the HARD drive (due to a hardware fault probably) and cannot start from the HARD disk.

  Then he pushes in the alternative startup > LAN
  The + PXE - E61: Media test failure, check cable + error because the laptop can not boot from LAN.

  I think that you just have to replace the HARD drive and then you need to reinstall new OS.

  This will help for sure.

• Satellite A45-S120 - SYSTEM32 error (CORRUPT FILE)

  I have a Toshiba Satellite A45-S120. I had to replace the hard drive once before because of the same error.
  When I try to turn on the putter i get-

  Lack damaged file system32\drivers\pci.sys on my screen. Any ideas how to solve this problem?

  I bought another hard drive, but when I put it in I -.
  PXE-e61:media test failed. check cable,
  on the screen.

  Thanks for any help or input.

  Mike @.
  M.G.H. CUSTOM GRAPHICS

  Hello

  This error appears especially if some or all of the system files are damaged.
  Usually the new OS reinstall should solve this problem.
  Use the recovery disk to reinstall the operating system.

  But many people have reported that this could occur due to hardware failure; Modules of RAM or HARD drive may be disrupted.

  PXE - e61:media test check cable error message appears because the laptop has attempted to boot from LAN. This is especially the case if the LAN boot option has been set to the first position in the BIOS or if the HARD disk is not available or not recognized.

  In your case, it could be a new drive HARD does not appear in the BIOS, which is not recognized.

• HP ATI Radeon HD 7450: Video card puts all monitors to sleep when the HDMI cable is connected

  I'm having a problem with a brand HP ATI Radeon HD 7450 part number 672459-001. When I plug a cable HDMI card put the monitor in standby. And when I unplug cable HDMI, the screen stays off until I restart the computer. The HDMI cable needs to be connected to anything in this case. It makes me batty to be honest

  Jim Hutto
  I do not work for HP.
  I am a computer technician and a passion for computing with more than 32 years of computer repair and networking experience

  Never mind, figured it out. It is the HDMI2av converter. The converter might work power HDMI port or a separate power connection. The card is not enough voltage to run it. Then when I plugged it without external power supply it would draw so much tension that he caused the GPU to lock up.

• Dell U2913WM monitor does not detect the cable to the DisplayPort input

  Hello world

  I just got my new U2913WM yesterday. It works fine other then he said no display port cable when on the display port entry. The monitor works fine with a cable DVI and my PC, but I get no cable error if I try to use a cable of DP with ether a PC or a Mac. I would get one to make them work with the cable of DP that my Mac will not pick up the correct screen resolution when you use HDMI.

  • I have 2 computers, 1 PC and 1 Mac.
  • My PC has 2 ports of DP and my Mac has 1
  • I tried the cable in all DP 3 ports with the same results
  • I went out and bought a new cable of DP and still had the same problem.
  • I tried to turn off the PC, Mac and the monitor and back on their return
  • I also tried turning and turn off the DP 1.2 setting in the monitors OSD
  Can anyone think of anything anyone else I can try? I'm kind of at a loss at the moment other then contact technical support.

  I know that this is a very old post, but I just stumbled on it all trying to solve the same problem. In the case where treated him as stupid as I was, there are TWO display on the Dell U2913WM Ports, in a (#4) and exit (n ° 8). Next to the HDMI is only, you want to plug it into one near the power cable. I realized this after 2 hours of tearing my hair. Hope this helps someone, if it isn't the op.

  

• Computer Dell laptop, OS preinstalled Windows 7 does not start. Error: PXE - E61

  Original title: Failure to Boot to

  Computer laptop Dell, OS of Windows 7 pre-installed. No disc restoration/reformat/install for 7. (This is bullcrap if you ask me). Does not start. Error: PXE - E61: Media test failure, check cable PXE - M0F: out Broadcom PXE - ROM

  What should I do here?

  See if there is a solution here: http://hubpages.com/hub/How-to-Solve-PXE-E61-Media-test-failure-Check-cable-Error

  J W Stuart: http://www.pagestart.com

• OfficeJet 3830: OJ 3830 does not communicate on the WiFi

  Just received today, and this was frustrating.

  First he couldn't be set up WiFi because I didn't know my WPS PIN code. It connected to the network and the network saw it, but they couldn't connect.

  So, I tried a USB cable for my old printer and the computer could not see.  I traded with cable from my wife and now two printer work. Why he don't like my first cable with 2 other printers were very good with him?

  And now, it will print over WiFi.   But it indicates that the computer is unable to establish communication in 2 directions with the printer.  He can get hardware information and levels of ink, printing, but no estimated.  (He get them on USB port)

  So it of not a big deal, but is it possible to establish communication in 2 directions, or perhaps that it does not work on Wifi?

  AM I very well having never given a WPS Pin NUMBER, that MS wrote is provided by the manufacturer of the printer?

  Thanks for getting back to me! I appreciate your efforts, and honestly I can't replace the printer address the issue that I am not sure that the printer is the question.

  I think that the best plan of attack at this stage is to uninstall and reinstall the software, disable antivirus, firewall and all software startup (boot). Hard reset the printer & router and make sure the firmware is updated on the printer and the router. If this fails, we can try another windows profile to make sure it is not something in the BONES of the origin of the problem.

  I know that this appears at first sight very complicated, but I burst in instructions step by step to make it easy to follow

  1. Unplug the USB cable from the printer to the computer (if it is connected)
  2. Hold down the Windows Logo key on the keyboard and the 'R' to open the dialog box run, type % temp %
     • Delete all files and folders in the temp folder. Choose Skip if all pop ups seem to say all files cannot be deleted
  3. Delete the printer devices and printers and the driver from the properties of the server. See the instructions below before proceeding to step 4.
  4. The new software - uninstall the printer software Instructions
  5. Once the uninstall is complete, reboot the computer
  6. Follow these steps to reset the registry settings and options for Windows Installer.
  7. Hold down the key of the Windows Logo on the keyboard and the 'R' to open the dialog box run
  8. In the Open box, type msiexec /Unregister, and then click OK.
  9. Hold down the key of the Windows Logo on the keyboard and the 'R' to open the dialog box run
  10. In the Open box, type msiexec/regserver, and then click OK

  * Note: there is a space between the c and the /.

  If you do not at this stage, use this link to perform another way. Restart Windows install

  1. Run the system Accessories\ tool disk cleanup <> How to delete files using disk cleanup
  2. Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayer/downloads.html
  3. Restart the computer - clean boot: How to perform a boot in Windows
  4. Let the router and the printer and unplug cable power both for a minute, then reconnect it.
  5. Download and install your software

  Please let me know if that solves the problem, or if you need assistance.

  __________________________________________________

  REMOVE THE DRIVER FROM THE PRINT SERVER PROPERTIES

  1. in the folder "devices and printers".

  2. choose "print server properties.

  • Win XP - with no printer selected, click 'File' then 'server properties '.
  • Windows Vista - with no printer selected, press 'Alt' and then click 'file' then 'server properties '.
  • Windows 7/8, 8.1 and 10 - select any printer in the "Devices and printers" folder and click on "Print server properties" above.

  3. click on the "Drivers" tab at the top of the window "properties of the print server.

  4. choose the printer that you want to uninstall, and then click 'remove '.

  5. choose "Remove driver only.

  6. the next screen will give a warning, letting you know that the removal of the driver package will remove it from the system. Click 'Yes' to say are you sure you want to do.

  If documents are stuck in the spooler to print, you see an error, cancel all documents waiting in the print queue or try restart the spooler to print, and then try to delete the driver from 'Print server properties' again. If she will not always remove the sachet, restart the computer and the printer should correct this error "in use" and allow the driver to be removed.

  • If him you continue to get an "in use" message followed the steps in the document here. The specified printer driver is currently in use

  Now go back to step 4 of the instructions above.

• Vostro 410 does not start

  I have a dell vostro. Worked fine for the last years, except now.

  Empty computer screen so my son off on your computer with the power button, now when you turn on the computer, the fan run continuously but not start or give error beeps.

  Button on the front is lit in blue.

  Checked the power supply, iy is ok and checked the memory, they are ok.

  any help would be

  242digital

  Try the following, if you are comfortable working around computers:

  Note: The only 100% POWER supply test method, is to install a known working power.

  Unplug the power cord, hold the power button in for about 15-20 seconds, open the case, disconnect the power connector 24-pin motherboard and jumping the Green wire to one of the black wires, plug in the power cord and the power of the system, if food and case fans and disk hard drive performance then the power supply should be good.

  Note: Do not remove the wires from the plug, use a small piece of wire or a paper clip as a rider.

  Excerpt from power supply, again, unplug the power cord, hold power in a few seconds to discharge residual power, reconnect the connector 24 pin to the motherboard.

  Remove all the computer PCI cards, remove the video card [as appropriate], disconnect all devices, except the monitor, mouse and keyboard and unplug cable power & data of all readers.

  Reconnect the power cord and power the system on, see if you get a different indication of the LED on the power button / stop, or 'beeps '.

  No difference, remove the system memory and try again.

  Still shows no signs of life while looking at a motherboard replacement & maybe a processor.

  Note: The processor rarely fails and the only method I know to check a processor, is to install a compatible working PC, or use a known job processing.

  Bev.