unrecognized hard drive compaq nc 6320

Similar Questions

• Tecra 9100 unrecognized hard drive

  Hello
  If I replace the hard drive in my tosh bios indicates no hard disk is installed.
  The new hard drive is MK2016GAP I tried with and without the master/slave relationship.

  Clues?

  Hello

  The MK2016GAP is a 20 GB HARD drive.
  I searched the Internet for the Tecra 9100 and discovered that the phone comes with 40 GB or 60 GB HARD drive.
  BIOS shouldn't t so no problem with the size of the HARD drive. The size of the HARD drive is certainly supported.

  So I think it's a problem of jumper or you did not connect the disk HARD corectly.
  I put t know how the jumper was set to your old HDD, but you should check the position of the jumper and put it also on the new HARD drive.

• Satellite Pro 4320 unrecognized HARD drive

  Hi all

  Please bear with me while I explain the disorder, that I am.

  I am a newbie in things pc & they gave me the laptop above to play with. He had only a small 6 GB HARD drive, so I bought a 30 GB internal disc used to install.
  I have the disc and followed the instructions on the internet on fdisk and formatting.

  Put the CD with the XP operating system and put XP on the drive. It worked fine for a few hours until I installed a network thingy usb dongle... then I'm nasty BSOD screens and couldn't go in the disk at all.
  The laptop refuses to recognize the drive.

  I tried to use an old Win 98 boot floppy in and none of the commands fdisk or format will take place, he said that there is no drive C.
  I also tried the XP cd, but will go only where the loading of drivers/utilities, then it stops and says that he does not find the disk, then press F3 to exit.
  I updated the BIOS to new supply & even that did not help. I must have done something wrong for lack of experience to get to this stage that the disc was recognized first.

  BTW, it will still recognize the old small hdd
  Someone at - it suggestions how I could get this disc recognized again?

  Thank you for taking the time to read this

  Hello

  Have you checked if the 30 GB HARD drive is distinguished by the BIOS?
  You need to access the BIOS settings and the full name of the HARD disk and the size must be visible in the BIOS.
  If this is not the case of the something might be wrong with the new HARD drive

  So please check it first and report the results

• Compaq presario s4100nx: how to remove the hard drive compaq presario s4100nx

  I removed the ropes attached to the hard drive. I also removed the 2 screws on top. but the hard drive doesn't go out. are there instructions for this particular model and where can I find it?

  Mahjal, welcome to the forum.

  Here's a guide that should help you remove the hard drive.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• unrecognized hard drive.

  I have a hard drive with windows vista home premium, but it does not start and don't want to be recognized by the pc. what I would do. Sometimes it shows when I use it as a slave, but when I'm looking inside, it desapears from my computer.

  Go to the website of the manufacturer of the hard disk and download their program of diagnosis/test for the hard drive.  Run it and check the hard disk.

• HP d530 - unrecognized HARD drive, "Non system disk or disk error"

  Greetings,

  It is a computer from a friend. It seems that he has lost the CD or diskettes shipped with the computer. I see that recognition of HARD drive does not seem to occur in the SETUP (BIOS), so I guess as a floppy disk or a CD some is necessary.

  Only startup options that are currently available are:

  CD-ROM

  USB

  Floppy drive

  No hard drive recognized. I was able to boot to the CD-ROM drive with a Linux LiveCD, but it also confirmed that no HARD drive is recognized at the time. I guess it is possible that port IDE 1 is dead.

  I have tried to reset the CMOS operating in SW50 5 seconds, but that has not helped to recognize the HARD drive.

  The model number is:

  HP d530

  SFF (DC578AV)

  p/n DC578AV

  Restore XP on this machine would be the best option, but if I can get the recognized HARD disk and install a version of Linux, it would be OK also.

  Thanks for any help,

  Doug

  Assuming that the hard drive is on a different IDE channel as the CD drive, try swapping them.  If the CD is always considered and the hard drive is not, it would make sense that the hard drive is faulty.  If the Linux Live CD can not see the hard drive after the Exchange, a sign that it's done.

• N200 unrecognized hard drive

  Hello

  I had a problem and now the hard drive is not recognized when I insert the XP installation CD. (he appears on the BIOS).

  I found this page: http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-67897

  and I think that's what I need. Only problem is that the driver is looking for a floppy drive and I can't seem to install the USB disk on key.

  It is said:

  "Specify f6flpy32.exe with name full path where you extracted the package in step 1 and double-click on".

  Arian has an idea of what that means? for example, I have the file on: D:\Documents\Personal\Lenovo and my USB is on f: what is the command that I need to write to install the driver on F:?

  Any help will be greatly appreciated.

  Lenovo will disrespect you or you do not understand the steps. The AHCI driver can be called from a floppy drive. Of course your N200 lacks a floppy drive, as well as Lenovo says here... .and I quote...

  Installation Instructions
  
  
  
   1. On another system, extract this package onto the hard drive.
  
   2. Connect a USB-Floppy Disk drive.
  
   3. Specify f6flpy32.exe with the full path name where you extracted
  
      the package in the step 1, and double-click.
  

  You will need to either buy a USB floppy drive, buy a portable internal floppy drive or use one of the other two methods that I posted above to integrate the driver.

  And if you plan to do this, I suggest that you download the latest F6 floppy driver from intel. Located here for 32-bit and 64-bithere.

  You must be sure to hit F6 when asked and specify ICH8M when you are asked to specify the AHCI controller.

• I have just connected my Apple G Drive (external drive) to my Laptop Microsoft - EXTERNAL HARD DRIVE - NOT RECOGNIZED. Help? Mapping drives?

  I just plugged my Apple G Drive (external drive) to my Laptop from Microsoft.

  Driving light - ON

  (It works fine on my MacBookAIR)

  EXTERNAL HARD DRIVE on the laptop computer of Microsoft Vista-

  EXTERNAL - UNRECOGNIZED HARD DRIVE.

  Help?

  I tried the drive mapping?

  No drive letter that appears.

  I tried Microsoft DIFFICULTY IT PROGRAM - it does not detect there is a problem - nor did he fix it.

  I need help/help - thanks

  Hello Campbell,

  I would be grateful if you could answer the following question:

  1. what Microsoft Fix It have you tried?

  2. you receive an error code or message?

  3. have you tried to connect another external hard drive?

  Try to use an external hard drive on another USB port or another computer and check.

  I suggest to follow the steps below and we update on the State of the question.

  Method 1:

  Tips for solving problems of USB devices:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Method 2:

  Install the latest Windows updates

  This method will install the latest drivers for your external hard drive USB device.

  a. click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.

  b. click find updates. When the scan finished, click optional review updates.

  c. click on the check box next to the update, and then click install updates.

  d. If you are prompted, read the license agreement, then click I agree.

  e. follow the instructions on the screen to download and install updates.

  f. If you are prompted, restart your computer.

  If your problem still exists, go to method 3.

  Method 3:

  Reinstall the USB controllers.

  This method addresses the steps where the USB driver currently loaded became unstable or corrupted.

  a. click Start, type device in the area Manager Search , and then click Device Manager.

  b. expand Bus USB controllers. Right click on a device, and then click Uninstall. Repeat for each device.

  c. Once complete, restart your computer. Your USB controllers will automatically install.

  For more information:

  Contact the Apple Support:

  http://www.Apple.com/support/contact/

  I hope that the information above helps you.

• Compaq elite 8300 all in 1: Compaq 8300 allin 1 bought with HARD drive erased

  HARD drive is completely wiped and no information system have also tried the keys F11 and it too is not go... can I get HP restore disks

  You can buy all of the surgeons computer recovery discsHERE. Just put the model number - need a more complete than all in a single desktop Compaq Presario.  Is HERE IS a SAMPLE for model number CQ1-1130.  For the model that you own should be the same price.

• HP Compaq DC7800: Seagate 1 TB hard drive would run smoothly on my pc?

  I use desktop core 2 duo Hp Compaq DC7800 with 2 GB of ram.
  Now, I intend to improve 320 GB to 1 TB of hard drive (Seagate Barracuda 1 TB 7200 RPM ST1000DM003 / MIN 64 MB Cache SATA 6.0 GB/s 3.5).
  -It would run smoothly on the system?
  -Is a good choice or 512?
  -This particular model of hard drive of another company?

  Hello:

  It is not the size of the hard drive.  In this model, you can go up to 2 TB.

  It is the speed of the drive that may conflict with the dc7800.

  Disks SATA 6.0 GB/s can have the problem that is described in the above-mentioned document, which mine had.

  If you don't want to take the risk of what happens, you have to get a SATA II (3.0 Gbps) drive, and they can be hard to find these days.

• Compaq 8510w: replacement HARD drive models?

  Hello

  I have a laptop Compaq 8510w (KE186EA; s/n CNU812285Y) with 200 MB of HARD drive installed. It is a Seagate ST9200420AS ('Momentus' family).

  Yesterday, the CHKDSK utility found some bad sectors, so I want to replace the HARD drive. This Seagate model is no longer sold. What other HARD drive models are fully compatible with my laptop? My laptop has the peculiarity of "HP Drive Guard" who takes care of my HARD drive in the case of a shock, I wonder if this feature requires a 'special' model of the disk HARD must be installed.

  I searched the web site of Seagate and other Momentus drives are listed there, but I'm not sure that they will fit my laptop; for example, none of them does support "shock protection" (or this function Seagate has nothing in common with HP Drive guard?).

  UPD: and I also wonder if I can use an SSD, and if yes - what settings should it?

  -Generally shorter readers won't be a problem, since readers usually rise in a way where the screws and SATA connectors are located at the same locations despite the height of the car. Just be careful not to exceed the height of the OEM disk (i.e. some of the 1 TB + drives that were 12 mm of height not suitable)
  
  -SATA type is not important. SATA 3 Gb/s, SATA 6 Gbps or fastest readers will work fine, because their speed will be anyway limited by what the storage controller hardware supports.
  
  D ' a generally, capacity have no impact on the production of heat. The 8510w, as a workstation type system, is designed to use the commands of higher performance. Newer players tend to be more thrifty in energy which means less heat. You should have no problem of compatibility based on the ability for any player < 2 TB.
  
  Personally, I think that the benefits of the hybrid hard disks are largely overrated. If you want real performance boost, GB SSD - well worth the money, the performance difference is day and night from a physical disk more you don't have to worry about damage to the drive drops or movement.

• PC HP Compaq 8200 Elite CMT: Replacement of the SSD HARD drive and Recovery Options

  I have a PC HP Compaq 8200 Elite CMT I went recently to drive HARD original for one SSD of 850 Evo from Samsung using Samsungs cloning/copying software. Everything went well and the PC is in use today. I do not see the partition D: Recovery on this machine more well, so I think this has not copied or was lost. I still have the disk that was replaced.

  I was wondering if there is a way to replace HARD drive like this with an SSD and everything by keeping the system recovery feature that was on the HARD disk, and if a set of system recovery disks of before installing SSD would continue to operate, or if I need to create new ones, and if I CAN create new ones.

  rgoodrich

  I did what you want to do (for example, to replace a disk with a DDI) and was able to retain the function of HP recovery - but it's because of two important facts.

  First of all, I used a DDI with the same capacity as the original HARD disk.  This is important because if you use a smaller SDS, the HP recovery feature will no more work as a reset begins with reformatting the drive and recreate the original scores - which will fail if the disc is too small.

  Second, I use Macrium Reflect product to 'clone' the HDD to the DDI, which means, he made an exact copy of the partitions on disk on the SDS.  So, when I swapped drives, the PC restarted without any problem.

  People have posted here on the use of the software from Samsung, and they seem to have problems restarting after use and (apparently) with successful copy from disk HARD original in the new SDS.

• Presario CQ5110F: COMPAQ Presario CQ5110F adding a second hard drive and...

  Good so I took the lead when writing my original post on how to combine the two computers successfully.
  Not enough research, no question, just a little say aloud... Sorry about that.
  http://h30434.www3.HP.com/T5/desktop-hardware-and-upgrade-questions/HP-Pavilion-slimline-s3505f-amp-...

  I had little time today messing with both ' puters and discovered...
  They need a good cleaning and had.
  The noise of the Presario is indeed the fan on the radiator, it's just old and tired. Who cannot be strong in a music room; new fan may not be too expensive.
  So I decided the Presario is my starting point.

  I would add the hard drive of the Slimline as slave; they have different connectors tho.

  (1) if I just unplug the V2000 CD reader (that has the straight plugs) and use them to connect the second hard drive will I just lost my CD player? It is very good.
  (2) what parameters of rider (if any) do I need to have on each disc? Do not see outside the car Slimlines.

  I looked closer 2 slots for RAM and noticed that beside them there seems to be 2 places in addition to the Board of Directors, unused with no present holders plastic.

  (3) is it possible to add more slots and double the RAM? I would get 8 + GB and a 64-bit system end by ;~)

  Neither office seems to have the ability to run 2 monitors as is. No problem 29 "should do for now.
  Can't see a way to take the card out of the Slimline wireless and put it in the Presario. Internet not immediately necessary, hard connection cable always an option.

  All the other tips and advice on how to optimize my sytem are also welcome.
  Thank you for your time and helping an old guy handyman.
  See you soon!

  COMPAQ Presario CQ5110F (2008ish)
  Processor AMD Athlon X 2 7550 Dual Core 2.5 GHz = Socket: AM2 +.
  Card mother = Narra5 M2N68 - THE Chipset: NVIDIA GeForce 6150SE nForce 430 Socket: AM2 +.
  Memory RAM = 4 GB RAM DDR2 DIMM PC2-6400 MB/s
  = Video/graphic card nVidia GeForce 6150SE integrated graphics
  Sound/Audio = Audio integrated Realtek ALC888S
  Hard = 320 GB SATA 7200 RPM drive
  CD/DVD Player = DVD +/-R / RW 16 X SuperMulti SATA drive
  OS = Vista Edition Windows Home Premium SP1
  Power = 300w
  Case = Mid size 38cmHx17cmWx43cmL ATX

  Hard drives has no different connectors if they are both SATA specifications like other post indicated.

  There is no adjustment to make on hard disks of the rider SATAS. According to me, that one can think of the old school the IDE drives.

  ) If I just unplug the V2000 CD reader (that has the straight plugs) and use them to connect the second hard drive will I just lost my CD player? It is very good.

  The image below is a diagram for your motherboard. You have enough SATA ports to be used for the second and even a third hard drive.

  

  DDR2 memory modules can be a little difficult to source. The current generation of add-on memory is the DDR3 specification.

  Perform a Google or any search engine is your preference in the memory of the source by using the update of Compaq presario CQ5110F RAM as keywords.

• laptop Compaq CQ58: id of failure to the dst short hard drive RGF0R0

  my notebook Compaq CQ58 3 year, husbands, froze and wouldn't respond, after a few hours I force it down by pressing the power button, when I tried to start it up again once he went int automaticic repair, it took more than 24 hours.

  but the computer continues to freeze and go into the auto repair each time and was unusable.

  I don't have a recovery disk, none came with the computer and stupidley has not created a when the computer was new. being the only other computer that I have a windows vista I could not create one on this machine.

  As their was anything important stored on the computer I decided to reset the computer hoping that would solve the problem.

  I followed the instructions and the computer seems to be going through the motions to reinstall when he got stuck in a loop of

  the HP points logo swirling

  a popup with the date and time and please wait

  a white screen with the top of the window cmd at the bottom left of the screen

  back to points logo and swirling HP

  a popup with the date and time and please wait

  a white screen with the top of the window cmd at the bottom left of the screen

  After 48 hours I force crashed computer

  I ran the race test that everything happened except the short DST hard drive

  Falure ID: RGF0R0 - 69781:-MFKT1F-60WU03

  This means that the hard drive needs to be replaced and if so should I also a recovery disc, the laptop is out of warranty

  Thanks in advance for any help

  Fiona-s wrote:
  
  

  I ran the race test that everything happened except the short DST hard drive

  Falure ID: RGF0R0 - 69781:-MFKT1F-60WU03

  This means that the hard drive needs to be replaced and if so should I also a recovery disc, the laptop is out of warranty

  Thanks in advance for any help

  Hello Fiona-s,

  Thanks for posting in the Forum of Support HP!

  I'm afraid that the HARD drive has failed - the question is material one and all simply restore/reinstall will not solve it. Yes, you need to replace the HARD disk new or better with the SSD. SSDS are up to 10 times faster than hard drives:

  > http://ocz.com/consumer/ssd-guide/ssd-vs-hdd

  > https://en.wikipedia.org/wiki/Solid-state_drive

  There are more than 100 manufacturers and sellers SSD, but personally, I would choose Samsung, Intel, Toshiba, or OCZ ones.

  Microsoft Windows 7, 8.1, and 10 have supported for SSDS. Vista and XP - no

  You will need a recovery media to restore the windows once you have installed the new SSD or HARD disk.

  You can get possible by contacting HP Support. Here's how:

  > http://support.hp.com/us-en/document/bph07143

  > http://www8.hp.com/us/en/contact-hp/contact.html

  > http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html

  Feel free to post if you have any other questions.

• Compaq 5000 desktop hard drive mounting

  2014-03-16

  A few weeks ago, I unintentionally deleted hard drive of my Compaq 5000US Office of the chassis without recording sound

  original location.  Now, I am at a loss to know where to put them back in place as it looks as if there is no place for it inside the computer.  I'm familiiar with the locations of the floppy drive, drive of CD-ROM and two empty boxes of filling.  It's really confusing.  I'll be very grateful to anyone who can tell me how to make this hard drive.

  Julianloui

  {Problem solved]

  Even if I wish to withdraw my original question that I started too early, I think that my answer may still be useful to someone who needs to know where the HD is mounted despite its obvious location.  The HD is locked in a metal cage mounted vertically behind the bottom of the front cover of the computer.   You can not miss.

  I had not actually removed the HD but the mysterious presence of an HD 20 GB lying around the computer made me think that she belonged to the machine. I should have better because the 5000US came with a 30 GB hard drive.

  Julianloui