Similar Questions

• Failover process dell equal logic ps6210 boxes

  Hi all

  I have a question about these boxes of PS6210 Dell equal logic. I have set up three boxes that are joined in a group and running in auto mode, ripping one of them is SSD and two others are of the SAS and NLSAS. After that, I started creating volumes on these boxes by accessing my SAN storage using this IP group address. And for now everything works fine.

  Someday I have to stop my infrastructure for the interview, and then I noticed that if all of the box goes out, first of all, all volumes created on this box disconnects. Seeing this kind of behavior, a question comes to mind , what happens if one of our box fails due to any reason, it can be about power or any other reason? What will happen then?

  I really need your help here.

  Thank you

  Gohar Sultan

  If you lose a 'box' that holds a slice of a volume of the realized volume is taken offline until the missing member returns. Think of a RAID0 network.

  His DNA Equallogic to distribute a volume more members within a pool.

  If you don't like that

  1 place only a single member in a pool

  2. If your members have different RAID levels, you can set the RAID preference for a volume. If possible, with that volume will be stored on a member have the right type of RAID. But this isn't a 100% guarantee!

  3. with a command line magic, you can change the distribution of volume and disable it. But you lose a lot of the EQL benefiz and how it works.

  EQL, Dell offers an availability of 99.999% and in 7 years with 30 members to manage no I never lose one.

  BTW: put a hybrid or all Member SSD with high capacity SATA/NLSAS set in the same pool it not the 'best' configuration.

  Kind regards

  Joerg

• Update firmware on Dell Powerconnect 6248P battery

  Hello

  I need to update the firmware on the switches on my stack, the stack consists of 3 all current 6248P to run version firmware 3.2.1.3 Powerconnect switches.

  I plan to stack in a 4 switch that is running 3.3.1.10 so I need to update my existing carpet before doing this.

  I would like to use auto update and upgrade the firmware on the circuit breaker that will modernize, then the rest of the stack, but the issue I'm having, it's that the documentation Dell tells me to enable synchronization of the firmware using the command "start auto-copie-sw" in the cli, however appears not to exist at all?

  Can someone advise?

  Thank you

  Steve

  The documents listed here.

  www.Dell.com/.../pwcnt_stacking_switches.pdf

  Is a little outdated. Therefore, the listed order is more part of the 6200/CLI firmware. By default, the switch will try and push any updated firmware for the other switches in the stack, no need to run a command.

  See you soon.

• Update Firmware on Dell PowerConnect 3548p

  Hi all

  I have dell Powerconnect 3548p and I want to update via telnet and I was wondering what the commands are as I tried those on the CLI manual.

  I made a connection with success of my tftp to the switch and vice versa.

  I am aware that this is possible through the web management, but I would like to know how to do this via PuTTY.

  Thank you

  You can update the firmware and boot code by using the command copy. Here are the commands that will be carried out.

  Update the boot Code and firmware

  Console # copy tftp: / // image

  See the boot to console #.

  Start console system #.

  Console # copy tftp: / // boot

  Thank you

• Latest firmware for Dell & KM714 universal receiver

  Hello, can someone tell me what are the latest versions of the firmware for Dell universal receiver and (as applicable) KM714 wireless keyboard & mouse?

  Drivers download pages are a mess and it's hard to find an appropriate update file or the game with the system (e.g. KM714 pilots are officially not available for Win10).

  Here's my current status of FW:

  

  Here is the link to July 2016 Driver Update: http://dell.to/2eQMR8n

  and for KM714 & WM514 Dell Update universal receiver:

  http://Dell.to/2eQNSxe

• Unable to update firmware for the PERC 5 controller / i on PE1950

  We have 6 PE1950 server with SAS PERC 5 / i integrated RAID controllers. Dell OpenManage complains about being obsolete PERC firmware. 2 servers I currently have running, firmware 5.2.1 - 0062 and 5.1.1 - 0040. I downloaded the latest version of 5.2.2 - 0072. I tried the update by the Windows package and who did not, and he complain about the OS being too recent. A server is Windows Server 2008 R2 and the other Windows Server R2 2012. So, I created a BACK USB key with Dell hard drive files and run update.bat. Who failed on both servers with the following errors:

  Firmware doesn't have flash. Stop!

  Failed to update Firmware for controller 0

  The process of updating of the firmware of the controller does not have!

  Both servers had the exact same mistakes as described above. Ideas on how I can get the firmware update successfully? I checked the package I downloaded is for the PERC 5 / I integrated.

  It's here (if that will allow me to post a link):

  www.dell.com/.../DriversDetails

  Hello

  Try this updated version and see if it works. He said that it was for the 1950s.

• Unable to update firmware DRAC6 past 1.10.13 on R610

  Hello

  I have a number of R610s I need to upgrade the DRAC firmware, so you can talk to our new management system. Most of them updated correctly when I left versions gradually 1.10.13 (their version) to 1.97.

  About 7 of them, however, will not move past 1.10.13. I have the version of the 1.11 firmware available via TFTP; When I try to install this (via idracadm, starting from the local operating system or a separate box or through the administrative SSH console) I get first "Firmware update is not current" then 'Firmware update operation failed' when subsequent attempts until I have make a racreset. I tried clearing space by removing the logs of the system, I have done a factory reset, drained flea power and the problem persists.

  I also tried to update from the Dell Repository Manager bootable media as shown here http://lonesysadmin.net/2011/03/07/the-easiest-way-to-update-a-dell-servers-firmware/. No joy.

  Finally I tried the update to a new installation of CentOS; the upgrade appears to start but is never-ending; fwupdate s presents 'The Firmware update Operation failed'.

  Is there any other approach, or y at - it logs I can check what goes wrong?

  Thank you!

  ClintonF_Dell,

  The first things that I would look into what version of BIOS and the lifecycle of the R610 controller run. If you do not update those in tandem with iDrac you may encounter problems of this kind. If they're behind then I test this on one of them and get the BIOS and the LC caught up and see if after a racadm racreset and NVram clear as the iDrac allows you to update.

  Also, have you tried to update the iDrac tab to update the iDrac with the firming.d6 file? To do this, for example, you download the iDRAC6_1.97_A00_FW_IMG.exe file and run it on a Windows system to extract the files, then find the file firming.d6 and save. Use it in the iDrac GUI tab updated. Now, I know that it is the current file name, so to keep walking until you need the 1.11 and so on.

  These are the current versions, if you are far behind in these institutions, I recommend walk them up as well.

  BIOS 6.4 - http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=C6MRW&fileId=3287843619&osCode=RH60&productCode=poweredge-r610&languageCode=EN&categoryId=BI

  Lifecycle controller 1.6.5- http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=F7XJ1&fileId=3364056173&osCode=RH60&productCode=poweredge-r610&languageCode=EN&categoryId=SV

  Let me know what you see.

• Update Firmware of BMC R610 of linux

  Hi mates,

  I need to update a few R610 servers, I would like to only update the BMC Firmware if possible without shutting down the machines, is - it possible? I'm running debian on these machines.

  I open it because I've been Googling much this and I found that maybe there are several ways to update the firmwares of server, including the iDRAC completely update, etc., but I am only interested to get the latest patches of cooling, so I guess that should be only update BMC.

  Could you please some direct me in the right direction? I looked and I found some binary files in dell FTP, but I need to be sure of where to find the correct firmwares for my machines and what is the most common method through linux so far.

  Thank you comrades, I appreciate the help.

  Hello

  There is no separate BMC firmware in R610. You need to update firmware iDRAC who BMC features as well. Down, you can load the latest firmware iDRAC at the bottom of the location

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/PowerEdge-R610?driverId=63KCR&osCode=NAA&FILEID=3287900761&LanguageCode=en&CategoryID=es

  You can update the firmware iDRAC without stopping or restarting the system. As you have debian on these machines, I recommend you update iDRAC using Web GUI. You can check below link with a video on the updating of the process. First half of the video is on the download of the image that has changed a bit. You can download the File Format 'Application' link above.

  http://en.community.Dell.com/TechCenter/systems-management/w/wiki/3206.updating-DRAC-firmware.aspx

• Update firmware on esxi servers

  Hi all

  I plan to update firmware on my two Dell servers.

  Now my lack of Manager as an official document or the site who said that the updated firmware will be supported by the ESXi software.

  It's after the upgrade of the card of network/BIOS firmware etc, this will be supported by the ESXI version.

  The servers are already in production.

  Can someone direct me to the site where I checked the firmware compatibility against ESXi software please

  THX

  Concerning

  Nicolas

  Check the supported firmware versions listed for each system after selecting ESXi 6.0 (assuming you're going to the latest version)... This is as close as "documented" you will find.

  https://www.Dell.com/support/home/us/en/04/product-support/product/PowerEdge-R710/drivers

  Firmware updates do not change the compatibility.

  If you're worried, see the release notes for red flags.

• Update firmware H730 on ESXi

  We have two R530 running ESXi 5.5. They run slightly updated firmware on controllers RAID minis H730 I would like to update.

  The problem is the firmware update files I can find are if you are on Windows or Linux. How do I the R530 firmware update if I run ESXi? I am aware of the image of Dell SUU, but it's more than 10 GB is size, which is much too big, even for a DVD double layer.

  Dell do not seem to offer a "hard drive" version of the firmware from what I see.

  tonybarrett in your case, you can start in the LCC (Life Cycle controller) to perform updates to the server.

  1.demarrez Lifecycle Controller: press within 10 seconds after the Dell logo appears.
  2Click on Firmware update and update Firmware of the launch.
  The select the update repository page appears.
  3Select FTP server as source location and then click Next.
  The enter access details page.
  4 in the address box, type the host or IP address of the FTP server name, and then click Next.
  Server FTP from Dell (ftp.dell.com)
  5The latest firmware is downloaded from Dell's FTP server, internal FTP server or FTP server of the service provider.
  The select updates page appears. For a component, compare the currently installed firmware version and the latest version in the current and available column.
  6Choisir the required components.
  7Click applies.
  Once the update process is complete, the system restarts.

• Update firmware 7.7.7 7.6.7

  My airport express and extreme are updated to firmware again offers:

  7.7.7 and 7.6.7 for adults.

  It is not announced and what's inside

  7.7.7: Airport Station of Base of the Firmware Update 7.7.7 Information

  On the Firmware Update 7.7.7 Base Station Airport

  Update firmware 7.7.7 is recommended for base stations all AirPort Extreme and Time Capsule to airport with ac 802.11. This update improves the stability and performance of your base station.

  This update:

  • Resolves an issue that may prevent communication between clients on the same network
  • Improves performance with an extensive network of comments
  • Resolves conflicts of potential names with Hello sleep Proxy

  For more information on updates firmware of base station at the airport, including instructions how to install the update, please visit: http://support.apple.com/kb/HT1218

  7.6.7: Airport Station of Base of the Firmware Update 7.6.7 Information

  On the Firmware Update 7.6.7 Base Station Airport

  Update firmware 7.6.7 is recommended for all Apple 802.11n Wi - Fi base stations including AirPort Express, AirPort Extreme, and Time Capsule from the airport. This update improves the stability and performance of your base station.

  This update:

  • Resolves an issue that may prevent communication between clients on the same network
  • Improves performance with an extensive network of comments
  • Resolves conflicts of potential names with Hello sleep Proxy

  For more information on updates firmware of base station at the airport, including instructions how to install the update, please visit: http://support.apple.com/kb/HT1218

  For more information on the use of products from the airport, go to the Support Page at: http://www.apple.com/support/airport

  Kind regards

  Shawn

• Update firmware on Satellite A200-1gh - noise emissions under Linux

  Hello

  I have a serious problem with the sound on Toshiba laptop. Many people have the same problem I have.
  An example:

  ________________________________________
  Hi there everyone
  straight to the point, I got no sound running ' bt3 beta computer laptop - Toshiba satellite a200 - 14 d, HD audio - Realtek ALC862 @ Intel 82801GBM ICH7-M - audio. I tried to fix it with a blender Kmix or alsa, even downloaded the Realtek driver name and installed, but bt3 built in Realtek driver. Still nothing"
  ________________________________________

  My laptop contains this sound card: 00:1 b. 0 Audio device: Intel Corporation 82801 G (ICH7 Family) High Definition Audio Controller (rev 02) @ Realtek ALC861-VD. There is a problem somewhere in the firmware of this map or the Linux kernel.

  We use Backtrack 3 who is Slax based Linux distro.
  I've been with many professional talking about Linux, Bud, no one is really sure what is the problem. They said several things to try; one of them is updated firmware. I've never done this before, I'm looking for help.

  Number of exact model of my laptop is Toshiba a200-1GH psaece

  Please help if you can

  > There is a problem somewhere in the firmware of this map or the Linux kernel
  What are you talking about boyfriend? This firmware of the sound card that you hear?
  I think you're confused.

  First of all there is NO firmware for the sound card. Second, the sound card is controlled by sound driver.
  Always is it that Toshiba laptops are preinstalled with Windows OS.
  Linux is not supported at this time, and you won't find driver for sound card for Linux.

  If you need a sound driver for this sound chip, you will need to download it from Realtek Web site!

  That s all about your firmware to his mysterious map.

• Satellite Pro A300 PSAG9E - unable to update firmware

  It has come to my attention that my laptop will not install updates of the firmware.
  I tried all updates firmware on the Web from Toshiba site and on-site support for other countries but still no luck.

  My laptop is a series of Satellite Pro A300 PSAG9E and when I try and install a firmware update a box telling me it's not compatible with my system.
  I checked the version proposed by the pdf file and I know that it is the basic version before the update, and I'm sure I have install the correct way of m.
  So I don't know what goes wrong.

  Does anyone else have this problem or knows something that could solve this problem? Because I'm at a total loss.

  Thank you

  Hello

  The European driver Toshiba page provides three firmware updates;

  _UPDATE for drive_ TS-L632
  + Changes have been made in order to correct the following: +.
  + Impossible to burn songs on iTunes to some CD media. iTunes error "the attempt to burn a disc fialied. An unknown error occurred (2131)"is displayed. +

  _UPDATE for drive TS-L632P TO02_
  + This firmware solves some problems in the optical disc drive. +

  _UPDATE for TS-L632H drive TO03_
  + This firmware solves some problems in the optical disc drive. +

  You have a TS-L632P and TS-L632H drive?
  Isn't it? Then you cannot update the firmware.

• Satellite M40-101 cannot update firmware

  I tried to update firmware for my dvd - rw on M40-101 laptop drive, but when I start the program it says only "the target disk is not connected". What to do with it? the problem is perhaps cause firmware for dvd - RW drive Matsu * a UJ-831, but the model is actually UJ - 830B?

  Post edited by: ruselok

  Hello Ruselok

  Where did you find this update of the firmware? This firmware update is given by Toshiba?

• L26500 61i: PROBLEM UPDATE FIRMWARE L26500 61i

  I can't update firmware. My latest firmware is 11.0.0.2 and when I try to upgrade to 12.00.00.5 I get this message

  SP - SP_12_00_00.5_mvl40 - x 86 - opt_B.signed.fmw: there are problems with the firmware file and the firmware update process has failed. The file you have selected may not be good, or the problem may be due to a transmission error. Please, start the firmware update process again. If the problem persists, please contact support.

  I tried to download it again, but it's the same thing...

  I have checked the connections on the back of the printer and found a LAN connection, I confused with the 360 LaTeX, sorry my mistake
  Another task to do, run the diagnostic menu of emergency update firmware.
  If issue still continue, run the hard drive recovery in the same menu