URGENT! RDP with Cisco 857

Similar Questions

• I'm losing configuration when I turned off my Cisco 857 router

  I bought the new router Cisco 857 of the shop. Router must have been used before as I couln can't go inside with name of user and password default cisco/cisco.

  Well I followed digital and reset the password for the user name and password. Now I have finally connected to Cisco CP express on my IE browser.

  I discovered that someone was using a router in the shop that's why I countries: ' t log in to him in the first place. In any case the problem is that when I changed my configuration and applies the settings he remembers until I turned off. When I turn on again he remembers all the parameters of this shop.

  He returned everything back: IP address, former account to level 15 and password - just like after the password reset.

  I tried again and he again lost the settings. So I found instructions:

  http://www.Cisco.com/en/us/products/HW/routers/ps233/products_tech_note09186a00800a65a5.shtml

  I followed it and changed once again all the settings of the router. My settings are still lost after the power on/off. I noticed that when I do everything first bit it shows

  0x2102 not 0x2142 like they think that is password reset mode.
  
  Here is my output from Hyper Terminal:
  =============================
  Cisco#enable
  Cisco#show start
  Using 3359 out of 131072 bytes
  !
  version 12.4
  no service pad
  service timestamps debug datetime msec
  service timestamps log datetime msec
  no service password-encryption
  !
  hostname Cisco
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 51200 warnings
  enable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.
  !
  no aaa new-model
  !
  crypto pki trustpoint TP-self-signed-3185909327
  enrollment selfsigned
  subject-name cn=IOS-Self-Signed-Certificate-3185909327
  revocation-check none
  rsakeypair TP-self-signed-3185909327
  !
  !
  crypto pki certificate chain TP-self-signed-3185909327
  certificate self-signed 01 nvram:IOS-Self-Sig#5.cer
  dot11 syslog
  no ip dhcp use vrf connected
  ip dhcp excluded-address 10.10.10.1
  !
  ip dhcp pool ccp-pool
  import all
  network 10.10.10.0 255.255.255.248
  default-router 10.10.10.1
  lease 0 2
  !
  !
  ip cef
  no ip domain lookup
  ip domain name molinary.com
  !
  !
  !
  username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.
  username username privilege 15 password 0 password
  !
  !
  archive
  log config
  hidekeys
  !
  !
  !
  !
  !
  interface ATM0
  no ip address
  shutdown
  no atm ilmi-keepalive
  dsl operating-mode auto
  !
  interface ATM0.1 point-to-point
  description $ES_WAN$
  ip nat outside
  ip virtual-reassembly
  pvc 0/38
  encapsulation aal5mux ppp dialer
  dialer pool-member 1
  !
  !
  interface FastEthernet0
  !
  interface FastEthernet1
  !
  interface FastEthernet2
  !
  interface FastEthernet3
  !
  interface Vlan1
  description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$
  ip address 10.10.10.1 255.255.255.248
  ip nat inside
  ip virtual-reassembly
  ip tcp adjust-mss 1452
  !
  interface Dialer0
  ip address dhcp
  encapsulation ppp
  dialer pool 1
  dialer-group 1
  no cdp enable
  ppp authentication chap pap callin
  ppp chap hostname [email protected]/* */
  ppp chap password 0 netgear01
  ppp pap sent-username [email protected]/* */ password 0 netgear01
  !
  ip forward-protocol nd
  !
  ip http server
  ip http access-class 23
  ip http authentication local
  ip http secure-server
  ip http timeout-policy idle 60 life 86400 requests 10000
  ip nat inside source list 1 interface ATM0.1 overload
  !
  access-list 1 remark INSIDE_IF=Vlan1
  access-list 1 remark CCP_ACL Category=2
  access-list 1 permit 10.10.10.0 0.0.0.7
  dialer-list 1 protocol ip permit
  no cdp run
  !
  control-plane
  !
  banner exec ^C
  % Password expiration warning.
  -----------------------------------------------------------------------
  Cisco Configuration Professional (Cisco CP) is installed on this device
  and it provides the default username "cisco" for  one-time use. If you have
  already used the username "cisco" to login to the router and your IOS image
  supports the "one-time" user option, then this username has already expired.
  You will not be able to login to the router with this username after you exit
  this session.
  It is strongly suggested that you create a new username with a privilege level
  of 15 using the following command.
  username  privilege 15 secret 0 
  Replace  and  with the username and password you
  want to use.
  -----------------------------------------------------------------------
  ^C
  banner login ^CAuthorized access only!
  Disconnect IMMEDIATELY if you are not an authorized user!^C
  !
  line con 0
  login local
  no modem enable
  line aux 0
  line vty 0 4
  privilege level 15
  login local
  transport input telnet ssh
  !
  scheduler max-task-time 5000
  end
  Cisco#
  Cisco#
  Cisco#
  Cisco#
  Cisco#
  Cisco#
  Cisco#
  Cisco#
  Cisco#show version
  Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
  ELEASE SOFTWARE (fc3)
  Technical Support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Compiled Fri 22-Jan-10 14:46 by prod_rel_team
  ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
  Cisco uptime is 20 minutes
  System returned to ROM by power-on
  System image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"
  This product contains cryptographic features and is subject to United
  States and local country laws governing import, export, transfer and
  use. Delivery of Cisco cryptographic products does not imply
  third-party authority to import, export, distribute or use encryption.
  Importers, exporters, distributors and users are responsible for
  compliance with U.S. and local country laws. By using this product you
  agree to comply with applicable laws and regulations. If you are unable
  to comply with U.S. and local laws, return this product immediately.
  A summary of U.S. laws governing Cisco cryptographic products may be found at:
  http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
  If you require further assistance please contact us by sending email to
  [email protected]/* */.
  Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
  .
  Processor board ID FCZ140792J5
  MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
  4 FastEthernet interfaces
  1 ATM interface
  128K bytes of non-volatile configuration memory.
  20480K bytes of processor board System flash (Intel Strataflash)
  Configuration register is 0x2102
  Cisco#
  Cisco#
  Cisco#
  Cisco#end
  Translating "end"
  % Unknown command or computer name, or unable to find computer address
  Cisco#reload
  Proceed with reload? [confirm]
  *Mar  1 01:19:27.786: %SYS-5-RELOAD: Reload requested  by username on console. R
  eload Reason: Reload Command.
  System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
  Technical Support: http://www.cisco.com/techsupport
  Copyright (c) 2006 by cisco Systems, Inc.
  C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memory
  Booting flash:/c850-advsecurityk9-mz.124-15.T12.bin
  Self decompressing the image : ############################################## [O
  K]
  Restricted Rights Legend
  Use, duplication, or disclosure by the Government is
  subject to restrictions as set forth in subparagraph
  (c) of the Commercial Computer Software - Restricted
  Rights clause at FAR sec. 52.227-19 and subparagraph
  (c) (1) (ii) of the Rights in Technical Data and Computer
  Software clause at DFARS sec. 252.227-7013.
  cisco Systems, Inc.
  170 West Tasman Drive
  San Jose, California 95134-1706
  Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
  ELEASE SOFTWARE (fc3)
  Technical Support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Compiled Fri 22-Jan-10 14:46 by prod_rel_team
  Image text-base: 0x8002007C, data-base: 0x814E7240
  This product contains cryptographic features and is subject to United
  States and local country laws governing import, export, transfer and
  use. Delivery of Cisco cryptographic products does not imply
  third-party authority to import, export, distribute or use encryption.
  Importers, exporters, distributors and users are responsible for
  compliance with U.S. and local country laws. By using this product you
  agree to comply with applicable laws and regulations. If you are unable
  to comply with U.S. and local laws, return this product immediately.
  A summary of U.S. laws governing Cisco cryptographic products may be found at:
  http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
  If you require further assistance please contact us by sending email to
  [email protected]/* */.
  Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
  .
  Processor board ID FCZ140792J5
  MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
  4 FastEthernet interfaces
  1 ATM interface
  128K bytes of non-volatile configuration memory.
  20480K bytes of processor board System flash (Intel Strataflash)
  no ip dhcp use vrf connected
  ^
  % Invalid input detected at '^' marker.
  SETUP: new interface NVI0 placed in "shutdown" state
  Press RETURN to get started!
  *Mar  1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State change
  d to: Initialized
  *Mar  1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0  State change
  d to: Enabled
  *Mar  1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
  up
  *Mar  1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
  et0, changed state to up
  *Mar  1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console
  *Mar  1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
  o up
  *Mar  1 01:19:27.352: %SYS-5-RESTART: System restarted --
  Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
  ELEASE SOFTWARE (fc3)
  Technical Support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Compiled Fri 22-Jan-10 14:46 by prod_rel_team
  *Mar  1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoing
  a cold start
  *Mar  1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
  *Mar  1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
  *Mar  1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, chan
  ged state to down
  *Mar  1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Ac
  cess1, changed state to up
  *Mar  1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
  nged state to up
  *Mar  1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administ
  ratively down
  *Mar  1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administ
  ratively down
  *Mar  1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state to
  up
  *Mar  1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state to
  up
  *Mar  1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state to
  up
  *Mar  1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
  ged state to down
  *Mar  1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
  et3, changed state to down
  *Mar  1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
  et2, changed state to down
  *Mar  1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
  et1, changed state to down
  *Mar  1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
  et0, changed state to upAuthorized access only!
  ===========================================
  Please help me as I am stuck and can't go any further....
  
  

  Hi Dragan,

  After you run the wizard Cisco CP Express, it should save the configuration set to update the flash on the router.  However, in your case, it seems this is not the case.  Therefore:

  1. Configure the device via Cisco CP Express--> do NOT turn off after that
  2. Connect to the router with Hyperterminal.  Enter the configuration mode by typing:
     Enable
     When you are prompted for a password to put in.  The line should now be router #.

     now type:

     write memory

     You see errors?  Otherwise, type:
     See the startup-config

     Check the output matches the configuration you've tried.  If Yes, then you are good to go.  If this is not the case, let us know all the errors you received.

• Pass through IPSEC on Cisco 857

  Hello people!

  I have gained reciently a Cisco 857 router. I want to do a site-to-site VPN.

  I set up the ATM0.1 with "ip unnumbered" VLAN 1 interface. I have not configured the router to enable NAT or PAT. VLAN 1 is configured with a public Ip of my ISP address. Behind the cisco router, I have a Zywall 5, this device is my VPN gateway. Initially, it works very well with the other soho router but it blocks often, for this reason, I decided to change it for a cisco router.

  My problem now is that the cisco router does not allow the implementation of VPN.

  Need to activate the IPSEC pass-through?, how can I do this?

  Thanks in advance!

  If you connect through the console:

  recording console 7

  If you connect via telnet:

  farm forestry monitor 7

  monitor terminal

  Concerning

  Farrukh

• VPN - SRP527W <>Cisco 857 established but no tx fraffic side SRP

  I have now established between SRP527w and cisco 857 ACE, but if I ping from a multitude of Cisco to a host on the side of the PRS I get only rx traffic in the tunnel, the stats keep tx 0 and ping is not answered.

  My tunnel is to send a voice call in IPSEC tunnel keeping DSCP bits, it communicates vlan voice SRP with Cisco lan.

  I have the SRP 2 VLAN:

  1 vlan for data on ports 1, 2, and 4

  1 voice vlan ports 1,2,3,4.

  I connect a netbook to port 3 and I can connect to the internet, but I can't reach by ping across the tunnel

  Perhaps the traffic of the vlan is voice natted with the ip address of data vlan?

  I need all traffic must go through the tunnel without being natted on the cisco side I have a policy to avoid the nat but don't know if SRP have no problem about it too.

  All gateways are ok

  Any idea greatly appreciated, thank you very much

  Hi, manual,.

  The RPS not NAT via the tunnel, which shouldn't be a problem.

  You try to ping a client in the remote subnet, or IP address to the VLAN RPS at the other end of the tunnel?  (Could you try both please?)

  See you soon

  Andy

• Compatibility of VLAN with Cisco

  Hello

  We just bought 10 x new Netgear switches (all M4100) to add to an existing Cisco infrastructure.

  Simple configuration with only 6 Valns.

  5: Admin, 30: VOIP, 101: management, 100: a set of Workstations, 102: second series of Workstations, 200: IPTV, 400: Internet, 401: Wireless Management

  All I wanted to do was: 2 last ports each switch netgear = T and all the VLANS. I have not identified all ports if I want to use in the appropriate vlan

  101 of VLAN is my Managementt Vlan. (Need to configure inter vlan routing for this to work)

  I only turned on three switches up to now and all three do not work. They work for a while and that packets but do not receive all.

  What I am doing wrong?

  What I need to get rid of the original vlan1 on the netgear?

  Is that what I need config in the STP to make these compatible with Cisco (300 and 400 series) switches.

  I use an optical backbone on Cisco and Netgear switches.

  Sincere greetings,

  OLAF

  Hi Moussa,.

  Thanks for reaching out.

  We got it working.

  Step 1: upgrade to the latest firmware.

  Step 2: Forget the MISTLETOE.

  We had a few questions about the old firmware - causing links to trunk have some incompatibility with their tag and removed the images between Cisco and Netgear brand.

  After the upgrade of the firmware that we had access to "switchport mode access" and "switchport mode trunk" orders fixing the access port and trunking issues.

  Thank you Mr President,

  OLAF

• Cannot use RDP with Windows server 2008

  Original title: a user cannot RDP

  Hello

  I have a windows 2008 R2 server with 5 licenses of Terminal Server. I set it up so that users can RDP to the server using RDP and access other machines via VNC, it's not connetced to a domain or whatever it is.
  All users can connect using any OS - Win XP, Win 7, but a user cannot get to their place of work - I can connect from home, of Germany, etc. using the same user name and password, but they can get on the server but their access is denied.
  They can telnet to the IP address but can't.
   

  Hello

  Thanks for posting the question in the Microsoft Community!

   

  You have any question using RDP with Windows server 2008.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Forum TechNet site:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

   

  If you need any other assistance, let us know and we would be happy to help you.

• X220i with celeron 857 upgrade

  I have a x220i with celeron 857. I want to upgrade the CPU, but as I know that the cpu is not removable. Is it possible that I buy a 220 Board with i7 2640 m x? He enters the x220i database? Thank you.

  The X 220 and X220i have the same chassis, so a straight Board swap will work. The better question is the cost effectiveness. Sometimes you can pick up a 220 X used with a better processor for less.

• iOS 10 with Cisco Jabber

  Dear Cisco support community,

  as seen on http://www.apple.com/ipad/business/work-with-apple/cisco/

  Only the spark is described here. There will also be a better integration of the call with Cisco Jabber?

  Spark.PNG

  

  According to me, they're trying to transmit only apple ios 10 best interactive aura to the customer of the spark. This does not mean that jabber for iphone will be less functional in ios 10.

• AnyConnect + possible PSK (pre-shared key) as under with cisco vpn client ikev1 and ikev2

  Is it possible to create a VPN Anyconnect of RA with just the name of user and password + pre-shared key (Group) for the connection, as could do for ikev1 with cisco VPN client? I am running 8.4.X ASA code and looks like tunnel-group commands have 8.2.X somewhat change. If you change the group type of the tunnel for remote access, now there is no option for IKEv2 PSK. This is only available when you choose the type

  Type of TG_TEST FW1 (config) # tunnel - group?

  set up the mode commands/options:
  Site IPSec IPSec-l2l group
  Remote access using IPSec-IPSec-ra (DEPRECATED) group
  remote access remote access (IPSec and WebVPN) group
  WebVPN WebVPN Group (DEPRECATED)

  FW1(config-tunnel-General) # tunnel - group TG_TEST ipsec-attributes
  FW1(config-tunnel-IPSec) #?

  configuration of the tunnel-group commands:
  any required authorization request users to allow successfully in order to
  Connect (DEPRECATED)
  Allow chain issuing of the certificate
  output attribute tunnel-group IPSec configuration
  mode
  help help for group orders of tunnel configuration
  IKEv1 configure IKEv1
  ISAKMP policy configure ISAKMP
  not to remove a pair of attribute value
  by the peer-id-validate Validate identity of the peer using the peer
  certificate
  negotiation to Enable password update in RADIUS RADIUS with expiry
  authentication (DEPRECATED)

  FW1(config-tunnel-IPSec) # ikev1?

  the tunnel-group-ipsec mode commands/options:
  pre-shared key associate a key shared in advance with the connection policy

  I'm getting old so I hope that it is not in another complaint curmudgeonly on the loss of functionality. :)

  Many small businesses do not want to invest in the PKI. It is usually a pain to deploy, backup, make redundant, etc..

  But it would be nice to have a bit more security on VPN other than just the connections of username and password.

  If this is not possible, it is possible to configure the Anyconnect customer to IKEv1 with PSK and name at the level of the Group client?

  If this is not possible, WTH did cisco end customer VPN cisco as a choice of VPN connection (other than to get more fresh mail of license)?

  I really hope that something like this exists still!

  THX,

  WR

  You are welcome

  In addition to two factors, you can also do double authentication (ie the two using the user name and password). Each set of credentials can come from a Bank of different identities.

  With this scheme, you can can configure a local user name (common) with password on the SAA (think of it as your analog PSK) and the other be the AD user identification information.

• ISA500 site by site ipsec VPN with Cisco IGR

  Hello

  I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

  But without success.

  my config for openswan, just FYI, maybe not importand for this problem

  installation of config

  protostack = netkey

  nat_traversal = yes

  virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

  nhelpers = 0

  Conn rz1

  IKEv2 = no

  type = tunnel

  left = % all

  leftsubnet=192.168.5.0/24

  right =.

  rightsourceip = 192.168.1.2

  rightsubnet=192.168.1.0/24

  Keylife 28800 = s

  ikelifetime 28800 = s

  keyingtries = 3

  AUTH = esp

  ESP = aes128-sha1

  KeyExchange = ike

  authby secret =

  start = auto

  IKE = aes128-sha1; modp1536

  dpdaction = redΘmarrer

  dpddelay = 30

  dpdtimeout = 60

  PFS = No.

  aggrmode = no

  Config Cisco 2821 for dynamic dialin:

  crypto ISAKMP policy 1

  BA aes

  sha hash

  preshared authentication

  Group 5

  lifetime 28800

  !

  card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

  !

  access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

  !

  Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

  crypto dynamic-map DYNMAP_1 1

  game of transformation-ESP-AES-SHA1

  match address 102

  !

  ISAKMP crypto key address 0.0.0.0 0.0.0.0

  ISAKMP crypto keepalive 30 periodicals

  !

  life crypto ipsec security association seconds 28800

  !

  interface GigabitEthernet0/0.4002

  card crypto CMAP_1

  !

  I tried ISA550 a config with the same constelations, but without suggesting.

  Anyone has the same problem?

  And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

  I can successfully establish a tunnel between openswan linux server and the isa550.

  Patrick,

  as you can see on newspapers, the software behind ISA is also OpenSWAN

  I have a facility with a 892 SRI running which should be the same as your 29erxx.

  Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

  Here is my setup, with roardwarrior AND 2, site 2 site.

  session of crypto consignment

  logging crypto ezvpn

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 2

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 4

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 5

  BA 3des

  preshared authentication

  Group 2

  life 7200

  ISAKMP crypto address XXXX XXXXX No.-xauth key

  XXXX XXXX No.-xauth address isakmp encryption key

  !

  ISAKMP crypto client configuration group by default

  key XXXX

  DNS XXXX

  default pool

  ACL easyvpn_client_routes

  PFS

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

  !

  dynamic-map crypto VPN 20

  game of transformation-FEAT

  market arriere-route

  !

  !

  card crypto client VPN authentication list by default

  card crypto VPN isakmp authorization list by default

  crypto map VPN client configuration address respond

  10 VPN ipsec-isakmp crypto map

  Description of VPN - 1

  defined peer XXX

  game of transformation-FEAT

  match the address internal_networks_ipsec

  11 VPN ipsec-isakmp crypto map

  VPN-2 description

  defined peer XXX

  game of transformation-FEAT

  PFS group2 Set

  match the address internal_networks_ipsec2

  card crypto 20-isakmp dynamic VPN ipsec VPN

  !

  !

  Michael

  Please note all useful posts

• Cannot reset the user vmail with Cisco Unified CM Administration password

  We use Cisco Unified CM Administration ver 7.1 with Cisco 7945 IP phones. I have a user who came to tell me that they could access is no longer the voicemail, getting PIN disabled. Ichanged the PIN with the Cisco Unified CM Administration that accepts the new pin without problem, but when we try from the phone, it does not work. Any ideas... Thank you Don

  Hi Don,

  For voicemail partners changes/updates, you should choose

  2 cisco Unity Connection Administration.

  Then; Users > Find/list > user associated with selectect > drop-down Edit > change passwords >

  Change voicemail password

  See you soon!

  SoC

  "Spend your life waiting,
  a moment that all do not come.
  Well, don't waste your time waiting.

  -Springsteen

• Problem with Cisco ACS and different areas

  Hello

  We are conducting currently a problem with Cisco ACS that we put in place, and I'll try to describe:

  We have ACS related directory AD areas, where we have 2 domains and appropriate group mappings.

  Then we have our Cisco switches with the following configuration,

  AAA new-model

  AAA-authentication failure message ^ CCCC

  Failled to authenticate!

  Please IT networks Contact Group for more information.

  ^ C

  AAA authentication login default group Ganymede + local

  AAA authorization exec default group Ganymede + local

  AAA authorization network default group Ganymede + local

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  !

  AAA - the id of the joint session

  But the problem is that with the users in a domain, we can authenticate, but not the other. Basically, the question is that when we check on the past of authentication, two authentications are passage and the display of 'Authentic OK', but on the side of the switch, there is a power failure.

  There may be something wrong with the ACS?

  Thank you

  Jorge

  Try increasing the timeout on IOS device using radius-server timeout 10.

  Do we not have journaling enabled on the ACS server remotely?

  -Philou

• Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  It's... AP compatibility depends on the code that runs on the WLC. This is a matrix that is a good reference.

  http://www.Cisco.com/en/us/docs/wireless/controller/5500/tech_notes/wire...

  Sent by Cisco Support technique iPhone App

• SX 20 with Cisco Call Manager

  Dear team,

  If I add the SX20 with Cisco Call Manager, do I need to install the software cmterm - s52010tc6_2_1.cop.sgn the SX20. If this isn't the case, then what I have to do, I can see only administrator external field in my SX20, where I gave my callmanager IP address but it is not save.

  BR

  Hello

  In order to save the SX20 in CUCM you for CUCM version 8.6.2 or later, and your SX20 must be running TC5 version or a later version.

  This file you mentioned, cmterm - s52010tc6_2_1.cop.sgn, is just a upgrade file that you install on CUCM, so that CUCM can update your point of SX20 endpoint automatically. But you can upgrade your SX20 manually using the file s52010tc6_2_1.pkg.

  To get help on how to register to CUCM SX20, take a look at these guides with the name "administer endpoints TC on CUCM". The Guide according to the version of CUCM you run:

  http://www.Cisco.com/en/us/partner/products/ps11424/prod_maintenance_guides_list.html

  I hope this helps.

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• Client VPN CISCO 857

  Hello

  I would like to know if CISCO 857 allows customers of Cisco VPN remote apart from site to site VPN software. I have heard that all cable cisco VPN devices allow connections to cisco VPN client software, is it true?

  Thanks a lot for your help

  Juan Manuel

  Juan,

  Let me explain a little further in order to clarify some of the terminology used, which could lead to confusion.

  Router Cisco VPN may terminate the following types of tunnels.

  Lan to Lan tunnels has.

  b. dynamic tunnels of Lan to Lan

  c. connections from VPN clients

  d. ends for easy VPN clients

  a & b are very similar

  c & d are very similar

  except - option c uses VPN (software) clients installed on the PC or MAC systems

  Option d, material uses to connect to the IOS routers. You can use a router or a PIX firewall or a 3002 or ASA to connect to the Cisco router that would act as an IOS Easy VPN server. But the device to connect to the easy VPN server is called an easy VPN client.

  Hope that explains the terminology a little more in detail.

  To answer your question, safety feature Easy VPN client and server support.

  And what you're trying to accomplish is option c. Thus, security feature option should work well for you.

  Hope that explains your queries.

  The rate of this post, if that helps!

  Thank you

  Gilbert