VCS-E calls directly to Codian MCU Auto standard

Similar Questions

• Forcemore than two end points to use Codian MCU

  I have a lot of C90s, E20s, 150 points of termination. I wish that the conferences of two or more to always use the Codian MCU.

  Can I do this with model templates.participant conference, or elsewhere?

  It depends on the specificity.

  If you book these conferences, using TMS, then you need to configure your advanced conference Options.  "Use of the external MCU in routing" must be set to "Always, except for point to point" and "Favorite MCU Type in routing" must be set to "TANDBERG Codian MCU".

  If these are Ad - hoc conferences, then what you want is Multiway (i.e. Conference Factory).  However, this requires a VCS.  The Guide deployment of Multiway for more details.

  http://www.Tandberg.com/support/DL.php?id=1119&dir=Deployment_Guides&fn=Cisco_VCS_Multiway_Deployment_Guide_X5.PDF

  Series L (T150) endpoints may not trigger a Multiway call according to the docs, but which may have changed since the doc is a bit outdated now.  They can be attached to a Multiway call however (L6.0 or higher).  MXP requires F8.0 or higher.

  If no one who works for you, your only option is to configure the Codian to create a new ad hoc conference on incoming calls to the conferences of the unknown and then give your a prefix of Service H323 MCU so that all calls with this prefix will route to the MCU and start a conference by using this code.  Make sure that your parent model has digital ID H323 and SIP registration active.

  The Codian in itself is not able to force someone to use for Multisite; This seems to be what you might think from model issues.

• TMS 14.3.1 played not well with Codian MCU 4520 - bug?

  TMS 14.3.1

  Codian MCU 4.4 4520 (3.57)

  After upgrading from 14.3 to 14.3.1 MSDS that I find THAT TMS is no longer recognizing the Codian as being registered at a Registrar SIP (VCS - C x7.2.2) and active SIP server address is empty.

  As a result, it is no longer allow me to plan only calls SIP; that is to say:

  

  In the above Conference, participants at the Summit must be either H.323 or SIP, participating below place SIP (JabberVideo customer 'business'), as well as participating number 3 (customer 'free' JabberVideo).

  Before the upgrade, I've always had the choice of SIP, H.323, and if necessary, IP, now I have only the choice of H.323 and where appropriate, IP.

  Curiously, when using multi-way, it will connect to the customer external jabber.com as SIP - SIP, while in a scheduled call, he'll be H.323 - SIP and appeal in the VCS - E it actually displays H.323 - H.323.

  I have no problems with the old MPS800; Active listed address in TMS SIP server as per normal, and I can choose to H.323, SIP and IP.

  So, is this a bug?

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

  In the MCU configuration.xml, should say something like:

  user_name VCS.example.com"registrar_name =" example.com"="[email protected] / * /"/ >" "

  The field that is empty in your TMS screenshot ("Active SIP server address") must have been populated by proxy_name value in the confiuration.xml that I can see.

  EDIT: looks like we have made a code change in TMS 14.3.1 when it comes to check the address of the SIP server: in previous versions, read and used TMS 'registrar_name', but from 14.3.1, it reads and uses the "proxy_name" instead.

  Kjetil-

• 4510 question not enabled SIP Codian MCU

  Hello, my company sent me a Tandberg VCS and a Codian MCU 4510 to configure and test our video phones) SIP (based on.  The only problem is that they have not provided me with an activation key product yet.  I'm going to encounter problems, until I get the key?  Thanks in advance!

  Hello, Emery, the MCU is not functional until you get the key. Your company should be able to get that for you either partner having bought it from or directly from Cisco beginning with the account manager or systems engineer. Or you can try to send the serial number of [email protected] / * /

• Cannot connect to the Codian MCU 4550

  I have a client who has a 4550 Codian MCU.  They recently had their lines ISDN, replaced by the local Telco Co. and since then the admins MCU have not been able to connect to implement calls.  They can reach the web interface, but can not go further.  I had to try and telnet/ssh into the device and run a password admin clear command but couln t connect, giving them the return "connection refused".  I have them also trying the connection by default where they do not have reset it and it didn't work.  Is anyone in this forum know of another way to get with admin rights and rest the two other accounts?

  Hi Shane. Telnet or SSH is not available on these units. If they can't get into the unit with the admin password, then a console reset_config may be your best bet. Also do not know why change of ISDN lines would this Holy as these microcontrollers have no direct ISDN connections.

  VR
  Patrick

  Sent by Cisco Support technique Android app

• Codian MCU 4505 content encryption is not possible

  Hello

  I'm having a problem with MCU 4505:

  If I put the SIP trunk to the Codian MCU (to route calls with a specific prefix) for the MCU to TLS instead of TCP, the content channel could not be seen on other participants. I see in the statistics of participants, that the content string is sent from one endpoint to the MCU, but not received from the other particpiants. In the view of the Conference, I saw the following message:

  TX of content: encryption is not possible

  I checked the docs, but the description of this cause is not really free explaining:

  The MCU is unable to send the encrypted video content to this participant.

  If I put the trunk for TCP, no encryption is used and the sharing prentation works as expected. Basically, the encrpytion works fine, because the audio and video channels are received and sent as expected.

  No matter who else knows this problem or ideas how to solve this problem?

  BTW: Versions of software:

  MCU 4505 4.3 (1.68)

  EX60 TC 5.1.4

  Jabber 4.5

  C20 TC 5.1.4

  

  Kind regards

  Paul

  It is noted as a known bound in notes;

  "The transmission of content SIP of the MCU by using the binary protocol (BFCP) ground control is not supported on.

  encrypted calls. To allow content to pass on SIP calls in a separate main video channel, you should

  Disable encryption on the MCU or target endpoint. »

  The MCU supports the transmission of content encrypted on H.323 calls only, but not the SIP.

• Send calls directly to voicemail problem

  When I click on the checkbox to send calls directly to voicemail, it checks, but as soon as I change screens and return to the options of the checkbox is unchecked. I searched to see if this issue had been discussed at the forum Droid 3, unless I missed it I think. Anyone else having this problem and if so any difficulty?

  Thanks Joelbon. I fixed the problem by removing the contact and adding them. I'll try what you suggested, if I run again the issue.

• Forwarding calls directly to voicemail with SPA525G

  We want to forward calls directly to voicemail without the call to the extension ring. Does anyone know of a workaround? Please advise if I should post this somewhere else.

  Thank you.

  Hello SPA52GUser,

  Depending on your system of phone if you have the option of setting up a dial plan by using a prefix, then the extension user to send the call directly to the virtual machine for the routing of calls.

  Example the UC500 series used the prefix 6 then the extension of the user to/transfer to call directly to computer users virtual.

  Hope this helps,

  Michael D.

  If this post is helpful please note or mark it as correct.

• Transfer call directly to voicemail, 3 methods

  Hi all

  I can't find a link on the OCC more. He looked at 3 different ways to transfer calls directly to voicemail. I speak not from CCM 3.3.2spD, which has been discussed on recent threads.

  The link that I speak not to use newer versions of the MAC and the unit. I used this a few months ago, but I lost the bookmark!

  Thank you, Randy

  in fact, you will find all the tips and tricks for every topic under the link General tech tip below:

  http://www.Cisco.com/en/us/partner/products/SW/voicesw/ps2237/prod_tech_notes_list.html

  There are 4 or 5 tips and tricks for any transfer directly to a mailbox here, one of them is probably the one you're looking for.

• Application of floor on Codian MCU

  Hi all

  I want to know the meaning of the events by Codian MCU log output when endpoint sent a request for floor.

  There are newspapers that I captured after that I sent a request floor MXP endpoint.

  Conference CONFERENCE Info 13959 29/07/2012 17:29:43.254 'Name of the Conference' - set floor participating 1272

  Participant of CONFERENCE Info 13960 29/07/2012 17:29:43.254 1272: grateful request floor

  13961 29/07/2012 17:29:43.299 CONFERENCE Info participant_message_fn 1272: request floor

  Could someone let me know what each line means?

  Best regards and thanks in advance

  Kotaro Hashimoto

  Hi Kotaro-san,

  Third line in the newspapers show the message, it is not sent by MCU.

  It shows the real message received by request IE MCU for floor.

  Not sure what is "fn" stands for.

  Kind regards

  Sagar

• T3 with Codian MCU

  Is it possible to run a system of T3 with a Codian MCU.

  On Cisco Live in London one saw a new 53xx Codian MCU, anyone know if TIP will run on this new platform.

  Alex

  Sent by Cisco Support technique iPad App

  Hello

  It is possible to have the system T3 to a Codian MCU conference join.  But note that the experience and the type of diagram you see will be very different from when you use the telepresence server.

  With respect to the MCU, 53xx, I think that it does not support the TRICK.

• Why are my automatic messages deleting, how can I stop the direct e-mail window auto deleing my email once it has been read.

  How can I stop the direct e-mail window auto deleing my email once it has been read.

  How can I stop the direct e-mail window auto deleing my email once it has been read.

   
  They are not deleted.  While in the Inbox: see tab | Message Filter button. Check to show all Messages, not Hide the Read Messages.
   
  Windows Live Mail help is in this forum
  http://answers.Microsoft.com/en-us/windowslive/Forum/LIVEmail?tab=all
   

• SIP spam attack and MCU and vcs - e call

  as far as I know sip call spam attacks is done against the videoconference, connected with a public ip address, I disabled the sip but im not sure if my mcu and vcs - e with sound are vulnerable to them? they pose no threat to security for them? and if so, how? and what can we do about it?

  It is a well known problem and it affects H.323 and SIP, take a look at the below threads:

  https://supportforums.Cisco.com/discussion/12340591/nuisance-h323-calls-SX20

  https://supportforums.Cisco.com/discussion/12336591/sourceh323idcisco-incomingcalls

  https://supportforums.Cisco.com/discussion/12508641/Cisco-source-spam-calls-stepped-complexity

  https://supportforums.Cisco.com/discussion/12613681/attack-vcse

  There are many more discussions on this issue, the above, this is just a small selection. :)

  You do not need to disable SIP on the VCS-E, all you need to do is turn SIP UDP unless you need it for voice services.

  You can protect yourself by using a CPL on the VCS-E who will avoid calls to go through your MCU, or anything else you have sitting behind the VCS-E. This is assuming that you are using a combo of VCS-C/VCS-E, with the VCS - C behind a firewall and the VCS-E outside the firewall, for example in the demilitarized zone.

  Having just trouble ask points of termination or MCU sitting in nature with public IP addresses.

  These scans, moreover, mainly looking for systems that will allow them to make free international calls.

  /Jens

  Please evaluate the answers and makr as 'answered' questions as appropriate.

• Is it possible to join/merge two conference calls in MCU for one call in the same MCU

  Situation - endpoint is part of two meetings of MCU (with one call on hold).  I want to merge these two meetings to the MCU.  Is there a way.  MCU is 45xx series and this is a deployment of VCS - MCU.  Thanks in advance.

  No way to merge that I know, I've had similar scenarios and there is no automatic way to do it, the Conference, the participants will have to unplug one and join the other.  Multiway will not work because that is intended to the unique endpoints being transmitted to a MCU, no MCU is not lift themselves.

• Jabber/MOVI routing over VPN on VCS-E calls

  Hi all

  I have a problem with the situation to follow.

  -2 Movi Client via VPN Tunnel on the motorway-VCS connectet

  -the two VPN tunnel on the same subnet.

  -Ice set up NO!

  Now the problem is that the traffic is passing through the VCS-E but goes multimedia traffic, which is in this situation via VPN would not be allowed.

  Is it possible to configure something that all signaling and media traffic is going through the VCS-E if the two MOVI Client on the same subnet?

  Best regards

  Georg

  The call between the Jabber bot and video customers have the same contact address of sip and IP source address, then VCS will treat as non-traversal call (client is not behind the firewall).

  That's why VCS won't stay in media routing.

  You are able to configure the VPN client DHCP range for the different subnet IP address?