VCS Regex ([email protected] / * /)
Hello, I noticed that when I try to call an IP address of a client Jabber video on the iPad, than if I just dial one IP address, it adds the SIP client Jabber domain name to the IP address and the call fails because it does not recognize this address format. I know that I can call by putting an alias in front of the intellectual property and it work, but what a transformation regex would I need to integrate into our VCS for the call to work if users want to just put the single IP address?
I want to take
Thanks, Patrick (\d{1,3}\.\d{1,3}\.\d{1,3}\.\d{1,3)} (@domain.com) Then replace with \1, which is the first capturing group that must be the IPv4 address. You might want to put a? After the domain.com) bit so that becomes optional when it stops to send in the future. Sent by Cisco Support technique iPhone App Tags: Cisco Support [Email protected] call blocking *. I see a lot of sip calls on my VCSe where [email protected] / * / ip ADDRESS or [email protected] / * / OR [email protected] / * / I was looking through the forums and found https://supportforums.Cisco.com/message/3401571#3401571 Source Destination Protocol duration status Peer Type shares at start 2013-11-15 12:26:27 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 12:26:23 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 12:26:20 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 12:26:16 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 12:26:13 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 12:06:56 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 12:00:53 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 33 seconds 408 / Request Timeout view local VCS
2013-11-15 11:05:26 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 10:14:14 sip:[email protected] / * / sip:[email protected] / * / <->SIP/SIP 32 seconds 408 / Request Timeout view local VCS
2013-11-15 10:08:32 sip:[email protected] / * / sip:[email protected] / * / <->SIP SIP 32 seconds 408 / Request Timeout view local VCS
It's my current CPL
I now would change to:
Is THIS CORRECT? It'll work, but you should have the two unathenticated and authenticated covered calls. Given that all your calls seems to come from @VCS_IP, then you can block all destinations by using * instead of specifying the address. Below is part of the CPL I use and it works for me. You can test if the CPL works or not using the VCS-E "tool to locate." In addition, you must disable SIP UDP on the VCS-E unless you really need, as these scanners use UDP to find potential targets. (Time only I had to re-activate if I have to make a call using the host name where the VCS-E did a search of A DNS record instead of using "normal" SRV records.) If you have ISDN deployed gateways, then you should also seriously consider changing the prefixes you use, i.e. Add # to the prefix to break the dial string. For example if your prefix is 99 and you want to call 9912345678, then you dial 99 #12345678 instead. Also see the deployment guide for more information about these issues - step 16, page 41 in particular /Jens Please note the answers and score the questions as "answered" as appropriate. Calls from [email protected] / * / ip addresses Hello world I get calls from [email protected] / * / IPS on my Highway VCS trying to dial different numbers. I activated a policy rule of local call to reject asterisk@.* to any destination. * but it does not work and I still get the call attempts. Someone has encountered this and knows how to stop these calls? Thank you Maciek Maciej, try to replace 'origin' with 'non-authenticated-origin' in your CPL, so that it reads as follows: CPL 'origin' field has a value of "is not far" If the message that the CPL is run for is not authenticated. You can find more information about the field of the 'non-authenticated-origin"in the VCS administration guide. Hope this helps, Andreas SMTP: MAIL FROM: [email protected] / * / blocks / expires First of all, I'm not a customer of Cisco, but a user of a network by a facility of PIX firewall. My username does not mean that I am affiliated with Cisco; It's just a way for me to remember it. I can't give you more details than the fact that there is a PIX protecting the network. I don't have its version number, unfortunately. In any case, here's the deal: I think that there is a bug in the way PIX handles SMTP sessions. Specifically, it seems to block/time out when I Specifies an address (MAIL FROM or RCPT TO) that contains a pipe character, ' | '. Some tests: (1) mail via localhost: no problem (2) mail via the internal host: no problem (no not a firewall) (3) mail via the external host: has a problem, but not systematically The interesting part is that the bug does not always occur. When I RCPT TO: [email protected]/ * / directly, everything stops and the connection times out. However, if I first RCPT TO: [email protected] / * / and subsequently, * in the same SMTP session *, RCPT TO: [email protected]/ * / he * is * working. Rather peculiar. Relevant sessions (with netcat): > [email protected] / * /: ~ $ nc firewalled.example.org smtp > 220 firewalled.example.org ESMTP Sendmail 8.12.10/8.11.4; Friday 20 August 2004 11:50:30 + 0200 > HELO example.org > 250 firewalled.example.org Hello [213.196.33.33], the pleasure to meet you > MAIL FROM: [email protected] / * / > 250 2.1.0 [email protected] / * /... Sender OK > RCPT TO: [email protected]/ * /. My orders starts with a ">", responses from the server with ' > '. As you can see, nothing happens after the RCPT TO command with a ' | '. > [email protected] / * /: ~ $ nc firewalled.example.org smtp > 220 firewalled.example.org ESMTP Sendmail 8.12.10/8.11.4; Friday 20 August 2004 11:51:13 + 0200 > HELO example.org > 250 firewalled.example.org Hello [213.196.33.33], the pleasure to meet you > MAIL FROM: [email protected] / * / > 250 2.1.0 [email protected] / * /... Sender OK > RCPT TO: [email protected] / * / > 250 2.1.5 [email protected] / * /... Recipient OK > DATA > 354 enter mail, end with "." on a line by itself > Subject: test 2 [email protected] / * / > . > 2.0.0 250 i7K9pD9i022438 Message accepted for delivery > MAIL FROM: [email protected] / * / > 250 2.1.0 [email protected] / * /... Sender OK > RCPT TO: [email protected]/ * /. > 250 2.1.5 [email protected]/ * /... Recipient OK > DATA > 354 enter mail, end with "." on a line by itself > Subject: [email protected]test *. > . > 2.0.0 250 i7K9pD9j022438 Message accepted for delivery > QUIT > 221 2.0.0 firewalled.example.org closing connection The first RCPT is to [email protected] / * / and works very well. Then, after the opinion of "message accepted", I begin a new mail and RCPT TO [email protected]/ * / * fact * work.
Is this a bug in the software PIX itself? Network administrators say they have no special rules put in place and suggest that I just have to use an address without a ' | '. The problem is that requires change of address confirmation e-mails, but they never get through. In addition, the syntax of the address is valid. Anyone can shed light on this issue? You can reproduce it on your installation? Nice analysis... maybe you should work with the PIX a little more.
In this case, however, no bug in the PIX (except that we through sometimes by your remark above). This behavior is specified. Of http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/config/fixup.htm#wp1103507 "The MAIL and RCPT commands specify who is the sender and the recipient of the mail. The e-mail addresses are analysed for strange characters. The pipeline character (|) is removed (replaced by a white space) and "<" "="">" are allowed if they are used to define an e-mail address ("' >" "must be preceded of '")<>
There was some talk to the command pipelinig user definable, but at this time, no final word. Sorry for the trouble. Scott [email protected] / * / PIX Interface I know and agree that the PIX does not meet the traceroute requestes @ external interface but I VPN connections to other companies that have other brands of VPN (Nortel, sonicwall) boxes and they not beleave that. I ve tried to find an official document from CISCO for show them the reality, but I ve not found who Who can help me? HI -. The PIX does not support the initiation of the traceroute command. It is not part of the set of commands for PIX. Also read the following document: http://www.Cisco.com/warp/public/110/pixtrace.html Hope this helps - Jay. Video Jabber for TelePresence, VCS-E connection problem Hello I recently configured control VCS, VCS Expressway and TMS. Two VCS servers are software X7.2 and TMS is on 14.1.1 commissioning is configured between the VCS control and TMS, everything works OK internally and users can log in their Jabber client of telepresence video. When you try to connect via the highway-VCS I get the following question: "connection refused by the server. Try to connect again later" Area authentication is configured like this: VCS-Highway Sub-area by default: do not check the credentials Area Sefault: Do not check the credentials Crossing area: Do not check the credentials VCS-control Default subfield: treat as authenticated Area by default: credentials check Subarea: Credentials Check {area which movi users register to regex function} Crossing area: Do not check the credentials Search the rules between the two VCS game [email protected] / * / OK. The only port of the restrictions in place here are between the VCS control and VCS Expressway, outgoing ports open to the highway of the SANCTION. It seems to me that there is a connection problem, as opposed to an authentication problem. also, do I need to configure a SIP domain local VCS-Highway even if I try to proxy, registration to the VCS control. Would be appreciated if someone can verify my authentication area also... Thank you Simon, to do this, you re normally the area on VCS - C as "check credentials. If you want to proxy of VCS VCS-C-E records, you should not add the SIP domain name to the VCS-E. "Rejected by the login server" sounds weird in this case, however, could you share what you use for this deployment, the SIP domain name so that we can verify that your DNS SRV records are fine? -Andreas Use the VCS to CUCM composition URI I have an external SX20 and internal jabber user The jabber username is [email protected] / * / and the extension number is 999 I want entering through the composition by CUCM But the path is external SX20 > VCS-E > VCS - C > CUCM > internal jabber user I can dial [email protected] / * /, it is successful But can not be used [email protected] / * / composition Can VCS the [email protected] / * / of CUCM? Or where I put in error? I suggest that you have a good look through the VCS of Cisco and the deployment of CUCM Guide and verify that your configuration is at least similar to that proposed to allow calls between VCS and CUCM registered endpoints. Looks like a lot that you are missing a search rule. If the above has not resolved your problem, I suggest you move your discussion in the section Unified Communications Applications forums at the section of telepresence , where are discussed more actively to these types of devices. Wayne Several VCS - C for the deployment of Jabber Hello I found no documentation if the following scenario is possible: -MSD 1 with TMSPE -1 VCS Expressway -Control of multiple VCS (different places connected by VPN) Right away: -Video jabber is configured on TMS with different areas -Jabber client credentials come from AD (all areas) -Jabber clients are on VCS Control 1 Scenario: -Several VCS control servers -Jaber clients will register to the VCS control of their zone / area (based on the rules related to the domain.) Ex: [email protected] / * / will record on VCS - C1,[email protected] / * / will record on VCS - C2, etc.) -1 easy to use TMS Thank you! Hi Valentin,. Yes, it is possible. Configure the various commissioning (SIP server address different VCS - C you want to register to the value), templates for different groups that you want to register on different VCS and affect the good model for groups. Also, be sure to activate the commissioning (from MSDS) on all VCS which should be able to sign up customers in service. Let me know if you have any questions, Arne Setup search rule of venture capital to Lync Server Hi Experts, I'm still learning on how to implement rules research on the RESUME. However, currently, I make the VCS with Lync Server integration. The installer is: -. 1. transport server) edge 2. end of Sling pool) (3.) what a single control VCs running X7.1 Network video SIP domain of my client configured on VCS's [email protected] / * / and it is the same for the field of Lync here. Video endpoints and lync so same domain clients. I'm confused about how I would install search rule on the RESUME that will target the Lync server. (I'm following VCS-Lync Deployment Guide) when the domain is same. Could you please help me, how the rule search would look like? Thank you Saurabh check an additional link for this... https://supportforums.Cisco.com/message/3586039#3586039 a nice thread where Andreas eliminated many things... Thank you Alok Call SCV-express to any endpoint Hello I want to configure VCS Expressway to appeal to any video endpoint, I think that I need to configure to understand all the addresses of the endpoints as: SIP URI: [email protected] / * / H322: [email protected] / * / IP address Could you please help me to determine all possible addresses in order to set up the necessary transformations and query rules. Thanks in advance. No problem, I would suggest that you use the tools > model tool verify or find in order to ensure that the transformations you want to Setup will work as you want, will help greatly. Don't forget to select responses like "right answer" for those who might have the same problems or question. Another thing, just ask, I'm sure someone might have the answer. Just keep in mind, the VCS includes [email protected] / * /, [email protected] / * /, or simply IP if is not your VCS and appeal to an external system outside your network. What license for protection of Email? Hello We have a UTM50 from 2013. The first license period expires now. We use Email Protection but that you no longer use the Web Protection. I've already updated our Messaging Protection license which is valid until the 1.1.2017. Our Protection Web will expire in 3 days. The system sent me an email today: "Critical functions like filtering URL infested with malware, blocking websites that empty your productivity, scanning and cleaning downloads infected with the virus, as well as blocking SPAM e-mail are all dependent on these licenses" Is it possible that SPAM blocking depends ob Web protection not on the e-mail Protection. It would be a strange behavior. The information contained in the pages of support Netgear says something different: http://kb.netgear.com/app/answers/detail/a_id/20830 What ist the right information? Can someone there explain. Thanks in advance. Michael After the expiration of the license for web protection last weekend the firewall blocks always spam. So I think it was a general message about the license expiring, but from my point of view, this kind of message is very annoying because you never know if there is a problem with filtering if you don't buy a license for the web anti-spam protection. This kind of email causes 'the fear '. If the junk e-mail filtering would have stopped we would receive hundreds of spam and which could cause chaos. I hope that netgear changes expired messages to be more precise. Thank you Michael Change the Source URI for outbound calls using VCS Expressway X8.2 Hi all I would like a little help on a CPL script, that I'm working on. I lived all the examples of community support and I am always sick. We run on VCS X8.2. What I've read, VCS X8.1 has introduced a few new CPL capabilities, including the node location CPL supports rewriting the regex-based source alias. I would like to take advantage of this new feature. I'm looking for a tutorial or a direction more advanced examples using this new capability. Here's my question: I have an internal domain "CompanyA.local" and I have a public domain "Entreprisea.com". «My Cisco video endpoints register control VCS with a SIP URI of "[email protected] / * / .local'.» Receive calls from outside help "[email protected] / * / com" and the rules of research, I route calls properly internally. When I dial an external company, my endpoint is showing a video SIP URI of "[email protected] / * / .local" Of course, this isn't a SIP URI dial-able and should be changed to "[email protected] / * / .com'." " I know that this can be achieved using CPL, but I have not used this feature before. Please suggest an example script CPL I can review. I would use a Regex to cover all of my similar to the following endpoints: source-url-to-message-regex = "(.*) ' @CompanyA.local '" Thanks in advance for any help. oooooo, that answer above gave me the answer I was looking for. It does not work! It seems that the syntax for the xml file has changed from pre x 8 and x 8. Looks like I've been using the incorrect syntax. I was missing the AVA: in the clause to the proxy, which is my version of rule switch not working. Still don't know why the address switch did not work, but I prefer the rule-switch anyway, so no big loss for me. I've tested, and it is fully functional on my vm VCS x8.2 running lab Hello have a problem with the composition of CUCM to VCS (7.1). The girl scout way works fine. I played with the rules of search and transformations, but it won't work. The terminal on VCS is a SIP device. Here is the log: "21 sep 11:14:26 tvcs: event ="Call rejected"Service ="SIP"Src - ip ="10.234.40.5"Src-port = '5060' type-aliases-Src = Src-alias"SIP"=" sip:[email protected] "/ * /" Dst-alias-type = "SIP" Dst-alias = "sip:[email protected]/ * /: 5060" Call-serial-number="bdb3272c-03cc-11e2-bef9-0010f3249b3a" Tag = "bdb32808-03cc-11e2-bbef-0010f3249b3a" detail = 'Not found' Protocol = "TCP" response code "404" = Level = '1' elements UTCTime = "2012-09-21 09:14:26, 549" "" "21 sep 11:14:26 tvcs: event ="Research Service completed "="SIP"type-aliases-Src = Src-alias"SIP"="[email protected]/ * / "Dst-alias-type ="SIP"Dst-alias =" sip:[email protected]/ * /: 5060 "Call-serial-number="bdb3272c-03cc-11e2-bef9-0010f3249b3a "Tag ="bdb32808-03cc-11e2-bbef-0010f3249b3a" detail =" "found: FAKE, searchtype:INVITE ' Level = '1' elements UTCTime ="2012-09-21 09:14:26, 549" "Sep 21 11:14:26 tvcs: Event = Service of" attempt of call "="SIP"Src - ip ="10.234.40.5"Src-port = '5060' CBC-alias-type = Src-alias"SIP"=" sip:[email protected] "/ * /" Dst-alias-type = Dst-alias "SIP" = "sip:[email protected]/ * /: 5060" Call-serial-number="bdb3272c-03cc-11e2-bef9-0010f3249b3a" Tag = "bdb32808-03cc-11e2-bbef-0010f3249b3a" Protocol = "TCP" Auth = "" level = '1' elements UTCTime = "2012-09-21 09:14:26, 539" "" "21 sep 11:14:26 tvcs: event ="Attempt to search"Service ="SIP"type-aliases-Src = Src-alias"SIP"="[email protected]/ * / "Dst-alias-type ="SIP"Dst-alias =" sip:[email protected]/ * /: 5060 "Call-serial-number="bdb3272c-03cc-11e2-bef9-0010f3249b3a "Tag ="bdb32808-03cc-11e2-bbef-0010f3249b3a"details ="searchtype:INVITE"level ="1"elements UTCTime =" 2012-09-21 09:14:26, 539 " Could someone help? Concerning Jason Jason, the desitnation is coming as "[email protected]/ * /: 5060" and intellectual property should be 10.224.35.249. What to change here, it's changing the rule search. No source Regex (. *) @10.224.35.249 ((:|;). *)? replace action chain-[email protected]/ * /. the SIP AOR is [email protected]/ * / so I think it should work after the chnges to find the rule. Rgds, Alok Control of Cisco VCS prefix add Hello I'm trying to get VCS to add a prefix to a string e.g. 33333 E.164 becomes 4233333. I tried to do by using the rule of research and transformation, but every time I test I still end up with an appeal that crosses as SIP rather the H.323, resuming a traversal license. What I have tried is the following; Transform Priority 6 Model Regex String [email protected] / * / Prefix for adding behaviors Add text 42 Search rule Priority '30 '. Protocol "H.323". Source 'everything '. AUTH 'no '. Mode "correspondence". Type "Regex". String '33, d, d, d. Behavior "replace". Replace "4233, d, d, d. Football match "continue." Target 'local area '. If I test the transformation it seems to work, but actually my call does not have the added prefix. I never had this work once, but then I ended up with 2 calls a trversed and the other no-treversal. The reason is we have a RMX 2000 bridge that records only the permanent conferences such as SIP and compose their H.323, to first in the prefix followed by the id of the conf. It is to make all the standard component throughout our Organization. Thank you Hi Craig,. As long as you try to send H323 to RMX, you replace the string should not have ' @domain.com ', the number. Please, try to send only "42\1" and if it doesn't work, then try only \1 «» Concerning Paulo Souza My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded." Hello I am configuring a search rule to direct calls to a specific domain. All numbers are 15xxx (each of them starts with 15). For reference, if the call to entry will [email protected] / * / it must be translated in [email protected] / * / and leave the area SIP domain which is privatedomain.com I try to do this ditch search rules, but I couldn't do it again. BTW, the VCS version is 5.2. Thank you Hi Douglas,. You can do this with a search rule or translation rule. The translation is always performed before searching for and allows you to change the number of the called party. Be aware, that only the translation could be used at a time. So if you have several translation only the first, which is to be applied. You can do this also with the rules of research. To look for a match with the correct regex. The positive effect is, if the alias is not found, it could be sought with the public domain too. The next rules are also processed, if the alias matches the regular expression and no alias registered was found and "on the correspondence" was set to continue. I have attached two screenshots, how it might look. BR Paul How can I stop my iTouch (old) screen turn? How can I prevent my iTouch screen first generation to turn? M530DLL.dll missing for Newport power meter 2935 and LabView I installed all the software and drivers with the Newport 2935 and when I try to run the included VI, I find that the file M530DLL.dll is missing. How can I change the ink for HP Officejet 4500? And why isn't this information available? HP 14 laptop: how to replace the QCA9565 of Qualcomm Atheros 802.11b/g/n WiFi Adapter Hello I have a laptop HP 14 which is currently used for academic purposes. However, at the school, the WiFi is dual band, and so I can't connect. At the moment I have a QCA9565 of Qualcomm Atheros 802.11b/g/n WiFi adapter and I am aware that is not Re deskjet 1280 driver Windows 7 64 bit. I have tried all sorts to nothing does not. Someone at - it suggestions?Similar Questions
--
Remember the frequency responses and mark your question as answered as appropriate.
Any help would be appreciated.
source-url-to-message-replace = "------[email protected] / * /"
"xmlns:TAA ="http://www.tandberg.net/cpl-extensions"
"" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance"
xsi: schemaLocation = "urn: ietf:params:xml:ns:cpl cpl.xsd" >
Maybe you are looking for