view client authentication

Similar Questions

• View client authentication failed

  Hello

  When connecting to the login server, it in. - to top the following error message:

  View connection server authentication failed. See connection server license code is not valid. Please contact your system administrator.

  Help, please!

  Thank you

  Ramesh. Giacalone,

  VCP 3 & 4, MCTS(Hyper-V), SNIA SCP.

  Please give points, so useful

  http://communities.VMware.com/people/geddam?view=documents

  http://communities.VMware.com/blogs/rameshgeddam

• Installation of VMWare view client issues with 64 bit Win8

  Hello

  I am trying to install VMware view client to access my VDI but I get the error message below... tried to install different products VMware, that nothing has worked... pls help.

  

  Its best you post your question in the following forums:

  Welcome | VMware Communities

• View Client to connect with expired password

  Hello

  One of our users has changed his password of Windows through the VMware view client. After a few minutes it disconnects and connects back with the old password and customer view allowed him to reconnect.

  But he was allowed to log in when he got connected to the desktop "password username Incorrect please enter the appropriate credentials. Is there a way that we can avoid this?

  We use the Horizon view 6 with Wyse D90D7 Windows embedded customers.

  Horizon View Client version 3.1

  Please notify

  It will be down to the local domain to the computer thinclient controller. A password must be replicated instantly, as it is reported as an urgent change. Best to check the local domain controller and that it the replication on OK. Can you see where the user changes his password and check out the ads and Services Sites and make sure your customers are in a site with a domain controller that runs. If it's a RODC then check the password replication policy.

• Overview of VMware VIew Client for Linux

  Hey everybody

  Is there a table of software compatibility for VMware View Client and Linux Horizon? We would like to use the client on devices based on linux, but we do not know what linux operating systems are currently supported.

  Dou you have a formal link or are you aware of the compatibility?

  Best regards

  Documentation (https://www.vmware.com/pdf/horizon-view/horizon-client-linux-document.pdf):

  Operating systems: Horizon customer 3.2 supports the following operating systems.

  Operating system	Version
  Ubuntu Linux	12.04 or 14.04
  Red Hat Enterprise Linux (RHEL)	6.5
  SUSE Linux Enterprise Desktop (SLED)	11 SP3
  CentOS	6.5

  IMPORTANT only 32-bit systems are supported.

  * Horizon customer 3.1: 32-bit Ubuntu Linux 12.04 or 14.04

  * Display Client 2.x: Linux 32 bit Ubuntu 12.04

  * View Client 1.6 and 1.7: 32-bit Ubuntu Linux 10.04 or 12.04

  * Display Client 1.5: 32-bit Ubuntu Linux 10.04 or 10.10

  VMware customer Horizon for Linux Release Notes

• VMWARE HORIZION VIEW 6.0: it does not serve any which RDS (using PCoIP) session to my zero Teradici Clients but it works with Horizon of VMware View client 3.0.0 from my computer

  Hi all

  I'm testing view Horizon 6.0 Service sessions (Windows 2008 R2) RDS through PCoIP. I think that my setup is just because I can connect via Horizion View Client (installed in my laptop or my Android smartphone). But when I try to connect from a Client Tera zero, 1 or 2 (with the latest firmware), at the same time I did logon, I still have this error:

  "View server connection has no return of available virtual desktops."

  Could someone tell what can be wrong?

  Concerning

  As a result of this discussion "Re: RDS support is included in Vmware View (broker)?" I saw that I must spend my customers zero to 4.5.1 firmware. Once I did, Tera 2 Zero Clients work very well but do not have customers zero 1 Tera.

  I expect response from Teradici.

  Concerning

• Overview of VMware View Client 3.0.0 - cloud icons missing?

  Overview of VMware View Client 3.0.0 build 1887158 - missing icons of cloud?

  After you have installed the Client of the view and adding a new server we do not see the icon 'cloud' over the connection to the server. The link to server connection works and connects - lack just the cloud chart

  

  Any ideas?

  Should look like this...

  

  OK, that explains it. Its a known problem when running in a terminal services session.

  Have no ETA on when it will be fixed.

  Linjo

• Help with renovation Horizon View client for Mac

  I'm packaging the client VMware View Horizon for our Mac desktops and laptops (we have about 150). Normally, it is a very simple and very easy process with this client because it is just a soft. We use Apple PackageMaker to repackage the Horizon of VMware View Client.appand add the plist for the test user for the deployment of future users profiles. We used some com.vmware.view.plist in the past to ensure that our connection to the server is prefilled and force PCoIP. It has worked great for us with all < 2.3 versions.

  From 2.3 and 3.0 now, I have not been able to repackage the application correctly. I have download the .dmg to VMware and copy the .app in it in / applications; This is exactly how a user would install it on their system. I run the Client discovers once and connect to our login server using the settings I want to paste when you deploy this application to our machines. Then using PackageMaker, I point the first part of the package that will be created for Applications/Vmware view Horizon Client.app as usual (including the roots). It's normal. I choose com.vmware.view.plist file, and I'm using a plist Editor, delete the entry for my test user name and office that I'm connected to. In PackageMaker, the destination of this .plist file is in the default profile for the mac - so whenever a new user connects to the mac, they will receive the file .plist with the parameters we want. Sounds good. The package is built successfully. I deploy it on a machine to test successfully.

  When I connect on a test system and run the client from the view, I can connect properly. If I try to use the menu connection/printing enabled, all hell breaks loose and I get a series of errors;

  Invalid file in the package.

  The file is not valid:

  / Applications/VMware Horizon view Client.app/Contents/Library/thnuclnt/thnusetup.sh.

  Please download the official product.

  If I try to start services remotely USB, I get a similar error once it issues a warning that I will be asked to enter the credentials of the admin;

  Invalid file in the package.

  The file is not valid:

  / Applications/VMware Horizon view Client.app/Contents/Library/InitUsbServices.tool.

  Please download the official product.

  ?? If I run the app from the .dmg on this same machine, I have no problem. Any ideas?

  OK, I just had to put the question so that I could think clearly through it.

  There are some extended attributes on these shell scripts that PackageMaker removes when it reconditions the app. I conditioned as a .dmg, and copy the app via the postinstall script in the pkg... works very well after that.

• How is the View Client to connect to the server has failed?

  Hello

  I have already set up the laboratory of Horizon view. But when I was about to connect to VM via View Client, an error message appeared.

  Pls check the photos attached. It seems that view Client connected to the server, but the recovery failed sources to the broker. And the average while servers introduced a healthy state in administrator mode.

  Step:

  1. launch View Client and login entry server IP address.

  2. a box will appear that him want to make sure that the server cannot be trusted. Then click on "continue".

  3. Enter the credentials, and then click "connect" button

  4. the error: "error: invalid server URL.

  What happened there? I have worked all day, still can not understand.

  No matter which help out me? Thank you.

  Step 1:

  

  Step 2:

  

  Step 3:

  

  Don't know if "_" is valid in a FULL domain name, try something else which corresponds to the period of investigation.

  Linjo

• Problem with USB Redirection on Horizon View Client v2.3.0 for Linux

  I had a problem on the USB Redirection when connecting to the Server of VMware View by Horizon View Client v2.3.0.

  1. Here is our configuration:
     1. Server:
        1. Horizon View Server 5.5 + Windows 7 Enterprise VDI
     2. Client:
        1. Thin client (TI ARM platform - 8148)
        2. Horizon View Client v2. 3 for Linux
        3. USB Flash: Kingston 8 GB USB 2.0, FAT32
  2. The issue: USB flash can not redirect to VDI successfully.
  3. Some status on our test:
  • The USB is plugged USB port on workstation before connecting to Horizon view Server 5.5
  • Light client can recognize and use USB flash to the local site.
  • When we connect to VDI, we can see the USB driver is responsible for research and installation, but windows VDI() reports fail to install the USB driver finally. It seems that VDI trying to acknowledge the failure of USB flash but finally.
  • It is held even Let's restart the workstation and VDI.
  • Attached file is the log of the Horizon of the VMware View Client.

  
  All welcomed to this topic?

  Unfortunately the newspapers show much... (note: they do not contain client-side logs)

  one thing I thought well... since he is a computer thinClient - we have seen the questions that manufacturers computer thinClient some of their own 'management' software install on the client. He often tries to do things with usb devices (maybe try to share them between a receiver client citrix application and view client app or maybe just there is a citrix receiver application installed too). In our experience, we've seen these apps interfere between them as they try to hang the bottom of usb devices down into the kernel.

  as such, could you try stop any 3rd party services - either citrix or your provider of thin client and then try again.

  If the problem persists, can you be sure to also collect these log files from the computer thinclient:

  Windows client

  • %ProgramData%\VMware\VDM\logs\debug-*.txt
    AND
  • C:\Windows\Temp\vmware-SYSTEM\vmware-usbarb-*.log

  Linux client

  • default /tmp/vmware-root/VMware-view-Usbd-*.log
    AND
  • / Library/Logs/VMware/vmware-usbarbitrator -.log

  for reference, the Agent-side usb connects:

  • %ProgramData%\VMware\VDM\logs\debug-*.txt

  see you soon

  peterB

• Problems with the module supplier of personalized identification information and overview of VMware View Client working together

  I have a Horizon of VMware View client that connects me HVD Windows 7. So when I give view client Vmware Horizon my credentials, it auto logs me. I also created a custom credential provider that works on Windows 7 PC. When I install the custom in the HVD credentials provider, it works if I am already connected to HVD and I simulate CTRL + ALT + DELETE. Can I use my credential provider to "unlock" in. However, if I disconnect of HVD and try to connect using VMware Horizon View client to connect to Windows 7 of HVD, it gets stuck on the screen of the tile. I see the VMware SSO user tile but nothing happens when I click it. Then, I use my provider of customized credentials to connect. I expect to bypass my ISP credentials on the first connection and self as before.

  Anyone have any ideas?

  Thanks for your help.

  OK, I did some more troubleshooting and discovered that it was a problem with auto connection set to TRUE on my side of custom credentials provider (I pbAutoLogonWithDefault to TRUE). Since I still like it TRUE, I had originally set it to FALSE and then change for REAL once my credential provider was used.

  Thank you!

• Horizon of VMware View Client cryptic error

  Anyone know what this error of the latest version of VMware Horizon View Client trying to say?

  

  My initial guess was she trying to say that the user has not right to the office pool. However, I know for sure that the user has the right. It seems to happen so far only for that user. I googled the error but nothing came.

  Any comments or advice, help reduce our troubleshooting.

  TIA!

  Something has changed in the configuration if the shortcut is no longer valid.

  What happens if you delete the connection parameters and the re - enter?

  Linjo

• Unable to connect to the outside through Horizon View Client

  http://www.VMware.com/files/PDF/view/VMware-view-evaluators-Guide.PDF

  I'm in the middle of evaluation of VMware Horizon View Suite. I set it up according to the information provided in the link above

  I am able to connect to my desktop PC internally through the Horizon View Client and HTML.

  I am also able to connect to the outside through HTML - BUT NOT - through the Horizon View Client from an external location.

  My first thought is that I have all the correct ports open on my firewall to network, that's what I opened, did I miss something?

  TCP / 80

  TCP / 443

  TCP / 4001

  TCP / 4172

  TCP / 8009

  TCP / 8443

  UDP / 4172

  Any help is appreciated with this!

  Exercise 3: connection to a Horizon of a customer of Mobile display view desktop

  "Launch the Horizon View Client you iOS mobile device...". "You will be asked to enter the host name or IP address of the view composer Server"

  See Server of composer? When I enter this IP address, it does not work immediately, it's a typo?

  Any help is greatly appreciated

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&docTypeID=DT_KB_1_1&externalID=1036208

  My problem was solved by following the information provided in the above document (video), but the following two documents where it is also very useful

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1028332

  0 224598712 http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=1039021&sliceId=2&docTypeID=DT_KB_1_1&dialogID=224578928&StateID=0

• SSH Tunnel on VMWare View Client

  I use the VMWare View Client on my Mac to connect to a Windows box in the behind a network business, then SSH for some internal network UNIX boxes. I really despise having to use Putty on Windows.

  Is there anyway I can use my native terminal under OSX (iTerm) to connect to the Unix boxes into the internal network? Is there a way to make the SSH tunnel runs on the client to view?

  -David

  N °

• VMware View Client Logo/skin

  We did it with other products before, but curious if we can change the skin of the Horizon of VMware View Client to something more exclusive to our society, such as our logo or by putting the name of the company in there.  We would also like to do on the Clients of zero if possible Teradici.

  Anyone done this?  I watched the local folder 'skins' under the program VMware View\Client, but these are the old skins (don't know why they are still there).

  Thanks in advance.

  I don't know if you should still do this, but I was able to achieve earlier on the VMware View client.  I discovered this by accident when I 'played '.  Within the facility there is a dll called wswc_en_us_409, it is in C:\Program VMware View\Client\bin.  You will need an application that will be able to open the dll, I think I used Microsoft Visual Studio.  In there is a bitmap (I think it's a bitmap) of the VMware View logo that appears on the client from the view.  If you create a bitmap with the same size, you should be able to replace it.  It worked on older versions of view, I do not know if it works on the latest version.

  To do this on customers of zero Teradici much easier.  In the profile on the management console, there is a parameter named profile OSD Logo which will allow you to upload an image.  You will need to set the OSD Logo to use for setting banner Login to true.