View of the horizon 3.5.0 and ThinApp v4.7 with Cisco ASA Smart Tunnel 9.3.3

Similar Questions

• View of the horizon 6 - customer zero can't see RDS Deskstop

  Hello!

  We have been in view for several years.  I just deployed a Desktop of RDS.  If I connect to the server from view with the client software from view of the Horizon, I see the desktop as an option, as well as other items of work to which I have the right.  However, when I connect to the server with a Client light Wyse zero (P20s and P25s), I can see other automated and manual office pools, but the RDS Desktop pool is not listed.

  This configuration is not supported?  Is there a parameter required to allow connects to RDS Desktops?

  Thank you very much!

  Update:

  I found this article:https://techsupport.teradici.com/link/portal/15134/15164/Article/2479/Do-PCoIP-zero-clients-support-Microsoft-Remote-Desktop-Services-15134-2479

  After that I updated one of the clients Tera2 zero to 4.7, I was able to connect to the RDS office pool.

  I'm glad to hear that you figured it out.  Can you mark this issue as resolved?

• I was change in 'Basic' in the 'Development' of Lightroom module, but in some sort the 'Basic' program has disappeared, and I find myself with more detailed editing tools that I don't want. How to get back the menu basic edition?

  Question: I've been change in 'Basic' in the 'Development' of Lightroom module, but in some sort the 'Basic' program has disappeared, and I find myself with more detailed editing tools that I don't want. How to get back the menu basic edition?

  Hello

  Click on the window inside Lightroom go to control panel > and select Basic from there.

  Thank you

• How Anyconnect VPN users will connect with cisco ASA, which uses the server (domain controller) Radius for authentication

  Hi team

  Hope you do well. !!!

  currently I am doing a project which consists in CISCO ASA-5545-X, RADIUS (domain controller) server for authentication. Here, I need to configure Anyconnect VPN and host checker in cisco asa.

  1 users will connect: user advanced browser on SSL VPN pop past username and password.

  2. (cisco ASA) authentication: VPN sends credentials to the RADIUS server.

  3 RADIUS server: authentication: receipt and SSL VPN (ASA) group.

  4 connectivity creation: If employee: PC so NAW verified compliance, no PC check Assign user to the appropriate role and give IP.

  This is my requirement, so someone please guide me how to set up step by step.

  1. how to set up the Radius Server?

  2. how to configure CISCO ASA?

  Thanks in advance.

  Hey Chick,

  Please consult the following page of installation as well as ASA Radius server. The ASA end there is frankly nothing much difference by doing this.

  http://www.4salesbyself.com/1configuring-RADIUS-authentication-for-webvp...

  Hope this helps

  Knockaert

• View of the horizon 6.2, 3.5 see Client and Windows 10

  Hi all

  I did an in place upgrade of Horizon view 6.2 over the weekend and have been very satisfied the performance and features.  However, I have a bit of a problem with Windows 10 company.  The VDI desktop resize not balance not as expected.  It seems that whatever the Windows 10 Office is set in vSphere, seems to stay when connecting with the customer to view.

  I had this problem for Horizon 6.1.1 with the 3.4 customer, but not a not sweat until this recent publication.

  I wanted to remove my image of Windows 10 company as being the culprit, so I installed a new version of Windows 10 Enterprise 64-bit with the latest tools from VMware View Agent and the problem persists.

  I'm under 6.0.0.b and ESXi 6 vCenter with the latest patches.  I can validate the scale/resize screen problem occurs on multiple endpoints, so I don't think the problem is with the endpoint device and the client.

  Any ideas?

  It's 3D acceleration.  Turned off, power off/on VM and everything works as expected.  (SVGA/NVIDIA) 3D acceleration is not supported in Windows 10?

• View of the horizon 6 without Active Directory

  Hello

  I have a Setup with 2 ESXi servers and stand-alone server with Win 2012 and here's installed vCenter.

  I need to install 6 view Horizon for workstation 5 only, and I have not installed the Windows domain and Active Directory.

  How can I install Horizon?

  I read that a prerequisite is AD.

  Can you help me?

  Thank you

  You could install the Direct Connect agent instead, which does not require an announcement but you won't be able to do any brokerage.

  Linjo

• View of the horizon - cmd Powershell for Description

  Hello

  Currently using:

  5.2.0 build-987719

  I had success by using the Get-DesktopVM and Get-pool for PowerShell cmdlets.  There is a cmdlet that will reveal the "Description" field that I can enter the pools on VM Admin view?  For example, if you navigate away from the Admin of VM window > inventory > pools > < poolID > is a Description field where we have notes on the pool.  I would like to retrieve this info so I can use it for further processing in additional systems.

  Please let me know if you need more information.  Is attached a screenshot of the computer virtual Admin window and the area I'm worried.

  Too bad

  The description field was actually available under Get-Pool.

• View of the horizon 6.0

  Can you upgrade from 5.3 6.0 on the Horizon while users are connected to the Desktops.Thinking I just disabled the commissioning.

  Part of the process restarts the connection broker service.   See the upgrade guide, https://pubs.vmware.com/horizon-view-60/topic/com.vmware.ICbase/PDF/horizon-view-60-upgrades.pdf

• I start the download for my CS5 and it comes back with an error that it can not install updates. and try later. I've tried about 6 times

  I start the download for cs5 and it comes back with an error that it can not install updates. and try later. I've tried about 6 times

  Hello Tracy,.

  How exactly you are trying to download and install updates?

  Is it a mac or windows?

  Manually download CS5 CS5 download products

  Download the updates manually CS5 for Windows here: https://www.adobe.com/support/downloads/product.jsp?product=39&platform=Windows

  Download the updates manually CS5 for Mac here: https://www.adobe.com/support/downloads/product.jsp?product=39&platform=Macintosh

  Concerning

  Jitendra

• VLANS with Cisco ASA 5505 and non-Cisco switch

  I have an ASA5505 and a switch Netgear GSM7224 L2 that I try to use together.  I can't grasp how VLANs (or at least how they should be put in place).  When configuring my VLAN on the ASA5505 it seems simple enough, but then on my switch, I thought I'd create just the same VLAN numbers that I used on the SAA and then add the ports that I wanted to use for each VLAN.

  Currently on my ASA, I have the following VLAN configured...

  outside - vlan11 - Port 0/0

  inside - vlan1 - Port 0/1

  dmz_ftp - vlan21 - Port 0/2

  Port of Corp - vlan31 - 0/3

  I need to do the same thing on my switch as well...  On my way, I'm a little confused as to how I need to configure the VLAN.  Below is the screenshot of web GUI...

  

  Note: Normally you can now change the VLAN ID (red), but in this case the default vlan (vlan id 1) may not be changed or deleted, you can does not change its settings.

  Tagged (green), Untagged (purple) and Autodetect (yellow) you must select at least 1.  I'm not sure how to in one place to tell my inner vlan (vlan1).

  I want VLAN1 ports 1-8 on my Netgear switch used alone to talk to interface/0/1 on the ASA5505 port.  I don't want to NOT port 9-24 able to talk to ports 1-8 on the Netgear switch ports OR 0/0, 0/2 - 0 / 7 on the Cisco ASA 5505.

  So, how can I configure my inner Vlan1 on ports 1-8 on the switch?  Do mark, UNTAG, autodetect them?  What about tours?  I've been a bit the impression that I would set up my VLAN on both devices, then trunk port 1 and dedicate this port on both devices to nothing other than the sheath and the security of vlan would then take the packages where they need to go.  Is this the wrong logic?

  Hi Arvo,

  If the port of the ASA is just part of a single VLAN (i.e. e0/0 single door 11 VLAN), this is called an access port. If the port of the ASA had to carry several VLANs, it would constitute a Trunk port.

  To access ports (VLAN unique), you must set the switch corresponding to be unidentified for port this VLAN individual. If you decide to configure a trunk port, then the port of the switch must be set for labelling for each of VLAN who win the trunk.

  For example, ASA I have:

  interface Ethernet0/1
  switchport access vlan 20
  !
  interface Vlan20
  nameif inside
  security-level 100
  ip address 192.168.100.254 255.255.255.0
  

  With the above configuration, the configuration of the switch would look like this (assuming the e0/1 port of the SAA is connected to 0/1 on the switch):

  VLAN 20 - 0/1 = untagged

  If instead you use a trunk port, the config would look like this:

  interface Ethernet0/0
  switchport trunk allowed vlan 10,20
  switchport mode trunk
  !
  interface Vlan10
  nameif outside
  security-level 0
  ip address dhcp setroute
  !
  interface Vlan20
  nameif inside
  security-level 100
  ip address 192.168.100.254 255.255.255.0
  

  Assuming that the ASA e0/0 port is connected to 0/1 on the switch):

  VLAN 10 - 0/1 = tagged
  VLAN 20 - 0/1 = tagged
  

  Hope that helps.

  -Mike

• View of the Horizon from VMware and Microsoft Lync 2013

  Hello

  I am currently working on a VMware View Horizon project and the cap of the great exhibition is Microsoft Lync 2013. I had the matching between the vdi Lync plugin and the Lync client in the virtual office to work. During the process of matching the right icon indicates the attempt of local loading audio or video devices. When I connect a USB headset it detects and when I perform a test call, I hear only noise and not a good tone. Can I use only Lync support audio or video devices or it can be any USB device? I also mentioned the details of the current configuration of VMware View Horizon.

  Overview of VMware View: version 5.2.0 - 987719

  VMware composer: version 5.2.0 - 983460

  VMware View Client: version 5.3.0 - 1042023

  Virtual desktop: Windows 7 SP1

  Computer based mobile operating system: Windows 7 SP1

  Lync Server: version 2013

  Access virtual office: Sonicwall NetExtender

  
  

  Please see the following guide:

  The ABC's of deployment VMware Horizon discovered 5.2 with Microsoft Lync 2013 | Blog of Computing VMware for the end user - VMware Articles

  You should also be aware of the following:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2064266

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2045726

• View of the horizon and 'Blast' Protocol

  Hello

  I have recently updated our login servers and security to view Horizon 5.2 and I see the option to enable HTML5 pool access, but it indicates that an office feature pack must be installed.  I was not able to find this "feature pack" anywhere.  I've been through the administrative guide for 5.2 and it really do anything don't speak HTML access.

  Can someone point me in the right direction so I can start to do some tests with HTML5 access to desktop from view?

  Thank you!

  According to the notes of https://www.vmware.com/support/view52/doc/horizon-view-52-release-notes.htmlversion:

  These components will be available shortly after the general availability of VMware View Horizon 5.2 and may subject to availability of the app in various application stores mobile device.

  I feel your pain, I was really looking forward to test access HTML 5.

• With both internal customers and external view of the Horizon, I do * have * to have at least a connection to the server by type of connection?

  If I want both external and non - VPN and LAN users internal to access desktops from view, I need to have a connection to the server dedicated to external users and another for internal? Right now I have one pair of Security Server-connection to the server and external connections work fine, but the internal connections are not. I have to get up at least a connection replication server and change the URL HTTPS Secure Tunnel for internal users only?

  Apparently, you don't need a connection to the server dedicated to internal users if you also external users and a security server. I found this during my troubleshooting. The URL of security server will be configured as administrator mode that external URL can be resolved and accessible while the URL to connect to the server will be configured with a URL can be resolved internally and is accessible in administrator mode.

• Two view of the Horizon, active sites: that load swing and what on user profiles?

  Hi all

  I have two questions about an active Horizon view deployment.

  I want to deploy two deployments of Horizon view separate in two places, 400 users in total. Users will have a privileged place in which they use a virtual office (all stateless desktop computers). When the preferential site is unavailable the user should automatically directed to 'other '.

  What load balancer is able to do this?

  • The load balancer must be able to direct users to their favorite site.
  • a single point of entry tot the environment view should be used at all times, for example view.mydomain.com

  How can I get replicated user profiles?

  • In the case of a site failure the user profile must be available on the second site without staff intervention.
  • I was considering Microsoft DFS, but if I understand correctly DFS replication of user profiles is not supported?

  Thank you

  Jacques.

  F5:s is most commonly used in these scenarios, take a look on the "always on reference Architecture" of VMware.

  http://www.VMware.com/files/PDF/solutions/VMW-AlwaysOn-validated-design-guide.PDF

• Why show black screen for some of my users with a view to the horizon?

  Hello

  I installed horizon view 6.0. now, I just have a problem sometimes some of my users connect to their desktop with vmware view client horizon just see a black screen and cannot do everything even when I'm this office openconsole in vsphere client no show and a black screen for solve the problem I have to restart this desktop computer and its not ok how can I prevent black screen

  now I see that my status of vmware tools was obsolete is so important?

  What di I do?

  Best regards

  Babak

  As often occurs when the wrong VGA driver is installed.  This occurs when the view Agent is installed on the desktop, and then the VMware Tools is updated after the fact.  The result is the driver included with the Agent to view VGA is replaced with the VGA driver in VMware Tools.  You can see some advantages to the relocation of the Agent of the view, or update the VMware Tools and then install the Agent from the view.